Stop band characteristics of a TESLA cavity coaxial-type HOM coupler

A TTF-type coaxial higher order modes (HOM) coupler has been used in a TESLA 9 cell cavity. It is impossible to measure the stop band characteristics of the HOM coupler with the cavity. A measurement device for the coaxial transmission line type for the HOM coupler has been designed at Peking University. Experimentally it was shown that the average voltage standing wave ratio of the coaxial transmission line is smaller than 1.08. The experimental results of the stop band characteristics of the TTF-type HOM coupler have been fitted for the simulation. This paper describes the design of the measurement device and discusses the experimental and simulation results of stop band characteristics of the HOM coupler.     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency(RF)cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode(HOM)couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility)HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project(PEFP)in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency (RF) cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode (HOM) couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility) HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project (PEFP) in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

Measuring the performance of the coaxial HOM coupler on a 2-cell TESLA-shape copper cavity

Coaxial High Order Mode (HOM) couplers have been fabricated at Peking University and their RF performance has been measured on a test device consisting of a coaxial transmission line and a 2-cellTESLA-shape copper cavity. The test results on the 2-cell TESLA-shape copper cavity with HOM couplers indicate that the coupler can cut off the fundamental mode TM010 and absorb HOMs effectively after a careful adjustment. The optimal angle of the HOM coupler with the beam tube is found. The initial test results of HOM couplers are presented in this paper.     

TESLA式高阶模衰减器的改进与设计研究

为了消除超导加速腔中高阶模场对加速粒子的影响, 在DESY的高阶模耦合器结构的基础上本文提出了改进的耦合器. 用HFSS程序针对1.5cell腔设计优化了高阶模耦合器, 得到高阶模耦合器对几种主要模式的吸收. 研究结果表明, 采用新型结构后, 衰减器对主要有害模的衰减由－40dB提高到－15dB, 使原有高阶模衰减器的性能明显提高. 该高阶模衰减器也适用于国产2cell超导腔的使用.     

Measuring the performance of the coaxial HOM coupler on a 2-cell TESLA-shape copper cavity

Coaxial High Order Mode （HOM） couplers have been fabricated at Peking University and their RF performance has been measured on a test device consisting of a coaxial transmission line and a 2-cell TESLA-shape copper cavity. The test results on the 2-cell TESLA-shape copper cavity with HOM couplers indicate that the coupler can cut off the fundamental mode TM010 and absorb HOMs effectively after a careful adjustment. The optimal angle of the HOM coupler with the beam tube is found. The initial test results of HOM couplers are presented in this paper.     

改进的TESLA式高阶模衰减器的实验研究

讨论了TESLA型高阶模耦合器的改进, 对所设计的改进型TESLA式高阶模耦合器进行实验, 对理论计算与实验结果进行详细分析, 结果表明改进的高阶模耦合器理论计算和实验结果符合得较好.     

RF characters study of a pick-up parallel-setting HOM coupler

A pick-up parallel-setting high order mode coupler(pps-HOM coupler)has been fabricated at Peking University.It has been tested on a coaxial transmission line and a 2-cell TESLA-shape copper cavity.The test result of the 2-cell TESLA cavity shows that the coupler can cut off the fundamental mode TM010 and absorb HOMs electively.As its RF properties are insensitive to the probe dip length,there is no need to adjust the probe repeatedly during practical operation.     

RF characters study of a pick-up parallel-setting HOM coupler

A pick-up parallel-setting high order mode coupler （pps-HOM coupler） has been fabricated at Peking University. It has been tested on a coaxial transmission line and a 2-cell TESLA-shape copper cavity. The test result of the 2-cell TESLA cavity shows that the coupler can cut off the fundamental mode TM010 and absorb HOMs electively. As its RF properties are insensitive to the probe dip length, there is no need to adjust the probe repeatedly during practical operation.     

同轴对称型主耦合器的研制

为更进一步提高注入器的性能,注入器使用的耦合器采用同轴对称耦合。给出了同轴对称耦合器的理论计算、具体设计以及实验情况。经过对模型耦合器多次微波传输测量调试以及对各个部位反射的细致分析,最后获得了较好的结果,证明了该耦合器的实用性和可行性。     

同轴对称型主耦合器的研制

 为更进一步提高注入器的性能,注入器使用的耦合器采用同轴对称耦合。给出了同轴对称耦合器的理论计算、具体设计以及实验情况。经过对模型耦合器多次微波传输测量调试以及对各个部位反射的细致分析,最后获得了较好的结果,证明了该耦合器的实用性和可行性。     

Design of a capacitive main power coupler for RF superconducting accelerators

An updated main coupler has been designed for the superconducting accelerator of Free Electron Laser (FEL) project under construction in Peking University. A capacitive structure is chosen for the main coupler. Numerical investigation using CST Microwave Studio demonstrates the cold window part. The other nonstandard structures such as holding rods and antenna are also optimized. The coupler uses a 95% purity Al₂O₃ ceramic cold window. The VSWR (Vottage Standing Wave Ratio) is 1.02 at 1.3GHz and the frequency bandwidth is 45MHz with VSWR<1.1. The electric field intensity is 8.5×10^－2kV/mm around the window with 20kW Continuous Wave (CW) transmitted power. The Q_ext is designed variable from 5×10⁶ to 1×10⁷.     

熔锥型宽带耦合器的研制

介绍了全光纤熔融拉锥型3dB宽带耦合器的理论设计，根据理论设计制作了样品。应用耦合模理论分析了全光纤非对称熔融拉锥型耦合器的宽带特性；提出了3dB宽带耦合器的制作方案，在此基础上制作了样品；对样品进行测试，样品带宽大约为300nm(在1300nm～1600nm波长之间)，附加损耗小于0.5dB，完全达到了实用化的要求。     

一种覆盖全通信波段的新型宽带偏振无关双芯光纤定向耦合器的研究

提出了一种新型的双芯光子晶体光纤, 应用全矢量有限元方法分析了光纤各种结构参数对光纤宽带特性和偏振无关特性的影响. 在此基础上优化设计了一种50:50的双芯光子晶体光纤耦合器, 在1.225—1.675 μm波长范围内实现分光比小于1%、两偏振态之间的分光比差小于0.5%的优良特性. 由于引入了仅对偏振特性影响明显的相对独立的中心调制区, 不仅降低了光纤的优化设计难度, 而且实现了与普通单模光纤相匹配的模场特性, 能有效地降低耦合器的接续损耗与制作难度. 研究成果为研制接续损耗低、超宽工作带宽、偏振不敏感等特性的新型光定向耦合器提供了理论基础.     

同轴波导中二维金属光子晶体的电磁特性

在同轴传输线内外筒之间引入金属支撑杆,建立了同轴传输线中二维金属光子晶体的物理模型。利用等效电路方法分析其传播情况,通过低频和高频近似得到了两个特征频率。其中,金属光子晶体的第一个带隙从零频开始,到第一特征频率截止;第一个通带从第一特征频率开始,到第二特征频率截止;第一、第二特征频率与金属光子晶体的等效电参数相关。利用CST软件对模型进行了仿真计算,验证了等效电路分析结果的合理性。仿真结果显示,在沿纵向具有N个周期的有限结构中,光子晶体通带分裂成(N-1)个传输峰。并根据其电场分布得到了色散曲线。     

双光子吸收对光子晶体定向耦合全光开关的影响

 利用时域有限差分方法,在非线性条件下,考虑双光子吸收效应的同时,建立了分析2维光子晶体定向耦合波导光开关的模型。数值计算结果表明,对于长度较短的波导耦合器件,在强控制光和非线性条件下,双光子吸收效应会对波导的耦合作用产生一定的影响,从而改变入射光的透射特性,使光开关控制的动态过程发生变化。故而在设计全光开关器件时,对强控制光条件下的非线性双光子吸收效应有必要作为影响因素考虑进去。     

双光子吸收对光子晶体定向耦合全光开关的影响

利用时域有限差分方法,在非线性条件下,考虑双光子吸收效应的同时,建立了分析2维光子晶体定向耦合波导光开关的模型。数值计算结果表明,对于长度较短的波导耦合器件,在强控制光和非线性条件下,双光子吸收效应会对波导的耦合作用产生一定的影响,从而改变入射光的透射特性,使光开关控制的动态过程发生变化。故而在设计全光开关器件时,对强控制光条件下的非线性双光子吸收效应有必要作为影响因素考虑进去。     

Polarisation characteristics of a 12 fibre coupler under femtosecond pulsed and continuous wave illumination

We report on the experimental investigation carried out in the polarisation characteristics of femtosecond pulsed and continuous wave beams propagating through a 1×2 fibre coupler. It is demonstrated that the polarisation states of pulsed and continuous wave illumination over the broad wavelength range can be preserved in a conventional fused fibre coupler. Furthermore, the fibre coupler acts as a low-pass spectral filter in the visible wavelength range with a splitting ratio between 99.6/0.4 and 99.7/0.3. The result is of importance for fibre-optic second harmonic generation microscopy which requires the polarisation preservation to extract molecular organization of a sample.     

Design of a capacitive main power coupler for RF superconducting accelerators

An updated main coupler has been designed for the superconducting accelerator of Free Electron Laser (FEL) project under construction in Peking University. A capacitive structure is chosen for the main coupler. Numerical investigation using CST Microwave Studio demonstrates the cold window part. The other nonstandard structures such as holding rods and antenna are also optimized. The coupler uses a 95% purity Al2O3 ceramic cold window. The VSWR (Vottage Standing Wave Ratio) is 1.02 at 1.3 GHz and the frequency bandwidth is 45 MHz with VSWR<1.1. The electric field intensity is 8.5×10m-2 kV/mm around the window with 20 kW Continuous Wave (CW) transmitted power. The Qext is designed variable from 5×106 to 1×107.     

高次模式同轴多间隙腔激励特性研究

提出了一种工作在TM₅₁-2π模式的Ka波段同轴多间隙谐振腔,使用CST本征模求解器研究了此结构的电场分布特性,并分析了基于外侧全通的耦合方式下该结构的冷腔模式特性。在此基础上,通过结合空间电荷波理论和CST三维粒子仿真分析,研究了在多电子注激励下同轴多间隙腔高次模式的起振特性,并分析了此种结构的模式稳定性与注-波互作用特性。研究结果表明：对于工作在Ka波段的TM₅₁-2π模式同轴多间隙腔,采取结构外侧全耦合的方式具有较高的模式稳定性;在此结构中,多电子注不仅会均匀激励起工作模式,也可能非均匀激励起竞争模式;不同于工作在基模的扩展互作用速调管,此种结构的速调管电场极值是分别建立的,因此激励电子注可放置在不同相位的电场极值处;在保持电子注电压、总电流不变的情况下,采取更多电子注的激励方式,需要更小的聚焦磁场。