表面改性纳米SiO2复合聚合物电解质的制备及性能

通过化学方法将具有增塑效果的环状碳酸酯基团引入纳米SiO2表面,并用FTIR与TGA对改性纳米SiO2进行了表征.将改性纳米SiO2添加到以聚氧化乙烯(PEO)为基体的聚合物电解质中,制备了复合聚合物电解质.通过DSC和交流阻抗等方法对该聚合物电解质膜的热力学和电化学性能进行了研究.结果表明,掺杂改性纳米SiO2的聚合物电解质具有更高的离子电导率,室温最高离子电导率可达到1.84×10-5 S/cm;具有较高的锂离子迁移数,最高可达到0.49,且具有更好的界面稳定性.     

二氧化硅@聚合物同轴纳米纤维

The preparation and formation mechamsm ot silica/polyvinylpyrrolidone(PAN) coaxial nanofibers were presented in this paper. The PVP-PAN composite nanofibers were obtained via an electrospinning technique, while SiO2 nanoparticles were prepared according to a Stoeher method. The measurements of water contact angle(WCA), the compared results of silica coating PVPPAN composite nanofibers with PAN nanofibers indicate that much PVP resided on the composite nanofiber surface, which resuks in the occurrence of SiO2@polymer coaxial nanofibers due to the formation of hydrogen bonding between silica and composite nanofibers and subsequent adsorption of silica on the fiber surface.     

草莓型PMMA/SiO2有机-无机复合微球的合成与表征

在纳米二氧化硅水分散介质中,借助于正离子单体甲基丙烯酰氧乙基三甲基氯化铵(MTC)与未改性纳米二氧化硅颗粒之间的电荷作用,通过MTC与甲基丙烯酸甲酯(MMA)的自由基共聚合,制备了草莓型的PMMA/SiO2复合微球.整个制备反应过程中,纳米二氧化硅无需表面处理,体系中无需另外加入乳化剂或助乳化剂,微球表面吸附的纳米二氧化硅对颗粒起稳定作用.详细讨论了纳米二氧化硅初始添加量、MTC浓度对复合微球的平均粒径、复合微球中二氧化硅含量及微球形态的影响.动态光散射粒度分布仪(DLS)测得复合微球粒径在180~300 nm之间,热重分析(TGA)表明复合微球中二氧化硅含量介于16.4%~40.8%之间.透射电镜(TEM)显示所得复合微球具有草莓型结构,二氧化硅于表面富集.     

纳米二氧化硅复合悬浮液合成及聚合物吸附研究

从水玻璃合成了纳米硅溶胶,并以它为起始原核,通过水解钛酸正丁酯沉积二氧化钛,制得了稳定的二氧化钛复合二氧化硅纳米悬浮液,研究了添加的高分子两亲分散剂聚醚多胺在硅胶粒上的吸附和二氧化钛沉积过程中的贡献。研究结果表明,添加的聚醚多胺吸附在硅胶粒表面,有利于硅溶胶的稳定;钛酸正丁酯-丁醇-硫酸水解反应是可逆的,二氧化钛向硅胶粒定向沉积,这些沉积物呈无定形态,在沉积过程中,吸附的这些添加剂发生离子化,其阳离子端基形成的离子氛有利于二氧化钛沉积,并能减少胶粒粘接或团聚。     

以聚合物乳胶为模板经表面引发原子转移自由基聚合制备空心二氧化硅纳米微球

均匀的空心纳米及微米球因具有可裁剪结构及良好的光学性能和表面性能,而具有非常广泛的应用前景,空心胶囊是一类重要的材料,它是通过不同的化学和物理方法,直接除去壳-核粒子的内核而获得的,目前主要是通过控制表面沉积。或利用静电相互作用层层组装。制备空心胶囊,但前者易于产生独立的无机粒子沉淀,后者的步骤太过繁琐。     

基于表面修饰聚丙烯酸合成超顺磁/荧光纳米复合粒子

在聚丙烯酸修饰的Fe₃O₄纳米粒子表面共价结合罗丹明B, 获得分散性和荧光信号均得到改善的超顺磁/荧光复合纳米材料. 分别用透射电子显微镜(TEM)、傅里叶变换红外光谱仪(FTIR)、热重分析仪、荧光光谱仪、X射线衍射仪(XRD) 和振动样品磁强计(VSM) 对合成的粒子进行了表征. 结果表明, 羧基化的Fe₃O₄纳米粒子和Fe₃O₄-荧光纳米复合材料的粒径基本相同, 为6～10 nm. Fe₃O₄-荧光纳米复合材料的饱和磁化强度为39.2 A•m²/kg, 室温下呈现超顺磁性, 具有较强的荧光信号.     

锆酸钡/聚合物复合中空纳米球的水热合成

采用聚合物辅助水热合成方法, 在强碱条件下加入PAA和PVA的混合液,实现了聚合物/锆酸钡复合中空纳米球的软化学一步合成, 而且球壳为有机-无机复合材料, 有望用于吸附分离、催化剂载体、轻质陶瓷和涂料等方面.     

纳米sio2/聚丙烯酸酯复合涂层的热降解

纳米sio2;聚丙烯酸酯;复合涂层;热降解     

草莓型SiO2/PMMA纳米复合微球的制备

在纳米二氧化硅水分散体系中,借助于碱性辅助单体1-乙烯基咪唑(1-VID)与未改性纳米二氧化硅表面羟基之间的酸-碱作用,通过1-VID与甲基丙烯酸甲酯(MMA)的自由基共聚合,制备了草莓型的SiO2/PMMA复合微球.整个反应过程中,纳米二氧化硅无需表面处理,体系中无需另外加入乳化剂或助乳化剂,微球表面吸附的纳米二氧化硅对颗粒起稳定作用.用动态光散射粒度分布仪测得复合微球粒径在120-330nm之间,热重分析结果表明,复合微球中二氧化硅含量介于15%-20%之间.透射电镜和扫描电镜显示所得复合微球具有草莓型结构,二氧化硅富集在表面.     

Pd/PdO纳米复合微球的合成及催化性能

采用甲基丙烯酸锌加速还原氯化钯(PdCl₂) 溶液中的钯离子(Pd ²⁺)为钯(Pd) 纳米微球, 进而用得到的钯纳米微球直接制备钯/氧化钯(Pd/PdO) 纳米复合微球. 通过扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 粉末X射线衍射分析(XRD)及X射线光电子能谱分析(XPS) 等方法对 Pd/PdO 纳米复合微球进行表征, 结果表明, 制备的纳米复合微球为表面粗糙、 大小均一的纳米微球. 采用紫外-可见吸收光谱(UV-Vis) 等方法考察了 Pd/PdO 纳米复合微球在对硝基苯酚(4-NTP) 还原反应中的催化性能, 发现其具有良好的催化活性和循环稳定性.     

以阴离子多肽为模板合成二氧化硅纳米空心球

以聚阴离子多肽(聚谷氨酸钠)控制合成了微孔二氧化硅空心球. 在合成过程中, 以3-氨丙基三甲氧基硅烷(APMS)和正硅酸乙酯(TEOS)为硅源, 聚谷氨酸钠为模板. 硅源与阴离子多肽模板之间的组装依照以阴离子表面活性剂为模板剂组装合成介孔二氧化硅的机理, 即S-N+-I-机理, 其中S表示阴离子多肽, I表示TEOS, N表示共结构导向剂APMS. 组装过程中质子化的APMS与阴离子多肽之间形成静电相互作用, 同时, AMPS和TEOS共同水解聚合形成围绕阴离子多肽模板的二氧化硅骨架, 多肽的二级结构为微孔孔道的模板. 以阴离子多肽为模板可以在不同的实验条件下控制微孔纳米空心球, 微孔亚微米空心球和实心球形貌的合成. 在生物矿化过程中, 阴离子多肽往往控制碳酸钙或磷酸钙的沉积, 而我们的实验结果表明, 在适当的硅源存在下, 阴离子多肽也可以诱导二氧化硅的沉积.     

Microporous Silica Hollow Nanospheres Templated by Anionic Polypeptide

Anionic polypeptide, the poly(sodium L-glutamate), was applied to fabricate microporous silica hollow nanospheres templated by the secondary structures of the polypeptide as porogens. In the synthesis, 3-aminopropyltrimethoxysilane (APMS) and tetraethyl orthosilicate (TEOS) were used as the silica sources, and the coassembly followed the mechanism of the anionic surfactant-templated mesoporous silica (AMS) through a S_-N₊-I_- pathway, where S indicates the anionic polypeptide, I indicates inorganic precursors (TEOS), and N indicates costructure-directing agent (APMS), which interacted with the negatively charged anionic polypeptide secondary structures electrostatically and cocondensed with silica source to form the silica framework. The product was subjected to characterizations of X-ray diffraction (XRD), infrared (IR) spectroscopy, thermogravimetric (TG) analysis, scanning electron microscopy (SEM), transmitted electron microscopy (TEM), and nitrogen adsorption-desorption measurement. It was found that the pH value of the synthesis solution was an important factor to the morphological control of the silica products. Besides the microporous hollow nanospheres, microporous submicron silica solid and hollow spheres were also obtained facilely by changing the synthesis parameters. Our study further implied that anionic polypeptides, which were able to control mineralization of calcium carbonate and calcium phosphate, could also induce silica condensation in the presence of proper silica precursors. It was also expected that functional calcium carbonate (phosphate)/silica-nanocomposite materials would be fabricated under the control of the anionic polypeptide.     

Fabrication of Fluorescent Porphyrin/Polystyrene Composite Nanospheres by Electrospinning

Fluorescent polystyrene(PS)/porphyrin(TPPA) composite nanospheres were successfully fabricated by electrospinning. The SEM images clearly show that owing to adding TPPA in PS, the averaged diameter of the composite nanospheres became smaller, from 1500 to 580 nm. Fourier-transform infrared(FTIR) spectra determined the chemical composition of the resulting PS/TPPA composite nanospheres. The photoluminescent(PL) spectral analysis indicates that the peak position of the composite nanospheres in either solid st...     

Alkaline Zn-air and Al-air cells based on novel solid PVA/PAA polymer electrolyte membranes

High ionic conducting solid polymer electrolyte membranes (SPEM) had been successfully prepared from poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA). The solution casting method yielded highly hydrophilic membranes with uniform structure that were suitable for electrochemical applications. The room temperature ionic conductivity of the alkaline PVA/PAA polymer electrolyte membranes was in the range of 0.142–0.301 S cm⁻¹ depending on the composition. The cyclic voltammetry analysis was carried out using Zn|SPEM|Zn and Al|SPEM|Al cells. The analysis results revealed the excellent electrochemical stability of these newly developed alkaline solid PVA/PAA polymer electrolyte membranes. Metal-air fuel cells were also prepared from the alkaline solid PVA/PAA polymer electrolyte membranes. The electrochemical cell performance was evaluated based on Zn-air and Al-air cells at C/10 and C/5 discharge rates. The experimental results exhibited high percent of utilization for metal powders at room temperature. It was up to 90% for Zn-air cell when assembled with PVA:PAA = 10:7.5 polymer electrolyte membrane and discharged at C/10 rate. The power density could be as high as 50 mW cm⁻² at room temperature. However, the cell percent utilization was reduced to 73% with the same composition electrolyte membrane when C/5 discharge rate was tested.     

改性PEU/LCP复合膜的设计、合成及其血液相容性研究

从分子水平角度对改性PEU／LCP复合膜的合成进行设计,TN1及复钙、溶血、血小板粘附试验测定表明：一定质量比的LCP与PEU进行共混交联复合,其复合膜的血液相容性及物理机械性能得到极大的改善。这说明,这种设计合成路线是可行的。     

PVA/PAA thermo-crosslinking hydrogel fiber: preparation and pH-sensitive properties in electrolyte solution

The preparation of thermo-crosslinking hydrogel fibers composed of poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) was presented. The hydrogel fiber was prepared by extruding the spinning dope from in situ polymerization of acrylic acid in the presence of PVA into coagulating bath of saturated ammonium sulfate aqueous solution. The network was formed by thermally heating the dried fibers under vacuum. The final hydrogel fibers exhibit pH-sensitive behavior and show hysteresis loop in the pH range from 2.5 to 12.5. The pH value at which the swelling ratio of the fiber had a jump shifted to lower value with increasing the PAA content within the network. Increasing the heating temperature and time for the fibers, the swelling ratio decreased and the jump point pH shifted to higher pH value. The oscillatory swelling/contracting behavior of the hydrogel fiber exhibited a well reversible pH-responsive property.     

Damping characteristics and mechanical properties of silica filled PUR/PEMA simultaneous interpenetrating polymer networks

Simultaneous polyurethane/poly(ethyl methacrylate) interpenetrating polymer network was synthesised by the one-shot route at the 70PUR/30PEMA composition ratio. This semi-miscible IPN exhibited its potential as a material for damping application by a broad loss factor (tan δ) ? 0.3 spanning a temperature range of 132 °C. The TEM micrographs revealed a multiphase morphology where the mixing between the two polymers was extensive. Incorporation of silica was made in order to study the effects of filler on the IPN properties in terms of glass transition temperature, dynamic mechanical properties, and mechanical and thermal properties. Dynamic mechanical thermal analysis indicated that the filler enhanced the damping ability of the IPN at certain temperature range. Furthermore, the addition of filler resulted in improved material strength.     

瓜胶/聚丙烯酸互穿聚合物网络水凝胶对模型药物的负载与控制释放

考察了以牛乳清蛋白(BSA)为模型药物,通过相平衡分配法制备载药瓜胶(GG)/聚丙烯酸(PAA)互穿聚合物网络(IPN)水凝胶的工艺条件.借助紫外可见光谱仪研究了载药水凝胶在结肠酶存在下的控制释放行为.结果表明:载药容量(CM)随瓜胶、丙烯酸用量的增加而下降,半IPN水凝胶的Cm较全IPN的略大;结肠酶能明显提高半IPN与全IPN中的BSA释放速率,且提高幅度随GG含量的增加而加快,GG/PAA IPN水凝胶具有结肠定位降解的特性,有望成为靶向结肠给药的理想载体材料.     

Modification and characterization of semi-crystalline poly(vinyl alcohol) with interpenetrating poly(acrylic acid) by UV radiation method for alkaline solid polymer electrolytes membrane

Semi-crystalline poly(vinyl alcohol) was modified by UV radiation with acrylic acid monomer to get interpenetrating poly(acrylic acid) modified poly(vinyl alcohol), PVAAA, membrane. The stability of various PVAAA membranes in water, 2 M CH₃OH, 2 M H₂SO₄, and 40 wt% KOH aqueous media were evaluated. It was found that the stability of PVAAA membrane is stable in 40 wt% KOH solution. The PVAAA membranes were characterized by differential scanning calorimetry, X-ray diffraction, and thermogravimetry analysis. These results show that (1) the crystallinity in PVAAA decreased with increasing the content of poly(acrylic acid) in the PVAAA membranes. (2) The melting point of the PVAAA membrane is reduced with increasing the content of poly(acrylic acid) in the membrane. (3) Three stages of thermal degradation were found for pure PVA. Compared to pure PVA, the temperature of thermal degradation increased for the PVAAA membrane. The various PVAAA membranes were immersed in KOH solution to form polymer electrolyte membranes, PVAAA-KOH, and their performances for alkaline solid polymer electrolyte were conducted. At room temperature, the ionic conductivity increased from 0.044 to 0.312 S/cm. The result was due to the formation of interpenetrating polymer chain of poly(acrylic acid) in the PVAAA membrane and resulting in the increase of charge carriers in the PVA polymer matrix. Compared to the data reported for different membranes by other studies, our PVAAA membrane are highly ionic conducting alkaline solid polymer electrolytes membranes.     

Semi-micro-monolithic columns using macroporous silica rods with improved performance

Monolithic silica columns in semi-micro-format have been synthesized using poly(acrylic acid) as a phase-separation inducer via a sol–gel route. The absence of a thick skin layer accompanied by deformation of the micrometer-sized gelling skeletons on the outermost part of the macroporous silica rod contributed to improve the efficiency of monolithic silica columns as thick as 2.4 mm in diameter. The kinetic plot analysis revealed that monolithic silica columns with macropore diameter of 1 μm and skeleton thickness of 1 μm with decreased macroporosity behave similarly to columns packed with 3 μm particles with slightly lower back pressure.