Formation of Ag nanostrings induced by lyotropic liquid-crystalline phospholipid multilayer

Morphological variation of the Ag nanoparticles embedded in a lyotropic phospholipid (1,2-dioleoyl-sn-glycero-3-phosphoethanolamine, DOPE) membrane during hydration was investigated. Hydration at 5 °C resulted in transformation of the Ag nanoparticles into a bundle of Ag nanostrings as the Ag nanoparticles conformed to the H(II) phase of the DOPE molecules. Above 30 °C, the nanoparticles quickly coarsened into large polygonal-shaped particles since high mobility of the lipid molecules overwhelmed the tendency for the Ag nanoparticles to order. The result provided an insight into the long-term stability of nanoparticles trapped in different lipid membranes depending on the structural ordering of the molecules.     

Biosynthesis and characterization of gold nanoparticles produced by laccase from Paraconiothyrium variabile

During recent years investigation on the development of eco-friendly processes for production of gold nanoparticles (GNPs) have received much attention due to hazardous effects of chemical compounds used for nanoparticle preparation. In the present study, the purified laccase from Paraconiothyrium variabile was applied for synthesis of Au nanoparticles (AuNPs) and the properties of produced nanoparticles were characterized. The UV-vis spectrum of formed AuNPs showed a peak at 530 nm related to surface plasmon absorbance of GNPs represented the formation of gold nanoparticles after 20 min incubation of HAuCl(4) (0.6 mM) in the presence of 73 U laccase at 70°C. Transmission electron microscopy (TEM) image of AuNPs showed well dispersed nanoparticles in the range of 71-266 nm as determined by the laser light scattering method. The pattern of energy dispersive X-ray (EDX) of the prepared GNPs confirmed the structure of gold nanocrystals.     

氧化铈促进的高效Au/Al2O3催化剂制备及其催化CO选择氧化反应性能

近年来,伴随全球能源危机的加剧,以及温室效应和细颗粒物等一系列环境问题出现,各国研究者正努力寻求和开发可持续利用的新能源来代替传统的化石能源.燃料电池具有能量转化效率高、对环境排放低和污染小等优点,作为一种新的环境友好型技术而广受关注.在众多的燃料电池中,质子交换膜燃料电池(PEMFC)因具有能量效率高和工作窗口温度
　　低等优势而备受关注.但是, PEMFC燃料以H2为主,主要来源是烃类的重整气,但其中痕量的CO (10 ppm)将会引起Pt电极中毒,导致PEMFC性能迅速下降,因此如何有效地祛除富氢气体中的CO并尽可能减少H2的消耗具有重要研究价值.目前, CO选择氧化法(CO-PROX)是公认的最简单、廉价和有效的办法之一. CO的消除通常选用霍加拉特催化剂,虽然Cu基催化剂具有低廉的成本和较好的CO催化氧化性能,但是当反应中有H2O和CO2存在时,其活性会迅速下降. Au催化剂具有优异的低温CO催化氧化性能,但在PEMFC的工作温度窗口为80–120oC时,随着反应温度提高, H2与CO之间的竞争吸附变强,采用单组分Au催化剂难于在80–120 oC内使CO完全氧化.因此,设计并制备高效的Au催化剂来提高其在PEMFC工作温度(80–120 oC)条件下CO-PROX反应活性和选择性仍然是目前该方向的难点.氧化铈(CeO2)是一种重要的稀土化合物,由于Ce具有独特的4f电子层结构, Ce3+/Ce4+在一定条件下可以相互转化,具有较高的储放氧能力,即能够在富氧条件下储存氧,在贫氧条件下释放氧. CeO2是一种重要的氧化反应催化剂载体,是三效催化剂的主要组成部分,在净化汽车尾气方面稀土元素具有独特的优势,广泛应用于CO氧化和NOx消除等领域中.最近,本课题组以自制的氧化铝为载体,制备了K掺杂的Au-Cu/Al2O3催化剂,其在CO-PROX反应中具有较好的催化活性和稳定性.本文在此基础上,利用Au与CeO2之间的相互作用,制备了CeO2掺杂的Au/CeO2/Al2O3催化剂和K掺杂的Au-Cu/CeO2/Al2O3催化剂.表征结果发现,催化剂中Au和Au-Cu纳米粒子的尺寸均一,平均粒径分别为2.4±0.4和2.8±0.4 nm.与Au/Al2O3催化剂相比, Ce掺杂的Au催化剂具有更高的金属分散度,拓宽了其CO完全转化时的反应温度窗口(30–70 oC).对所制备的Au催化剂进一步通过拉曼光谱、H2程序升温还原和CO-红外光谱等手段分析和CO-PROX催化性能测试,可以证实Au-Cu/CeO2/Al2O3催化剂中各组分在CO-PROX反应中所起的作用.结果表明, CeO2的掺杂能增强活性组分与载体之间的相互作用,有助于提高Au-Cu纳米粒子的分散度,此外还能提高Au催化剂的还原性能,其表面形成的氧空位提高了CO-PROX反应的催化性能. Cu物种的引入显著增强了CO在Au催化剂上吸附能力.综上所述, CeO2组分对Au/Al2O3催化剂的促进作用体现在：(1)有效锚定Au和Au-Cu纳米粒子;(2)提供CO-PROX反应中的活性氧物种.     

Highly transparent superhydrophobic surfaces from the coassembly of nanoparticles (≤100 nm)

We report a simple and versatile approach to creating a highly transparent superhydrophobic surface with dual-scale roughness on the nanoscale. 3-Aminopropyltrimethoxysilane (APTS)-functionalized silica nanoparticles of two different sizes (100 and 20 nm) were sequentially dip coated onto different substrates, followed by thermal annealing. After hydrophobilization of the nanoparticle film with (heptadecafluoro-1,1,2,2-tetrahydrodecyl)trichlorosilane for 30 min or longer, the surface became superhydrophobic with an advancing water contact angle of greater than 160° and a water droplet (10 μL) roll-off angle of less than 5°. The order of nanoparticles dip coated onto the silicon wafer (i.e., 100 nm first and 20 nm second or vice versa) did not seem to have a significant effect on the resulting apparent water contact angle. In contrast, when the substrate was dip coated with monoscale nanoparticles (20, 50, and 100 nm), a highly hydrophobic surface (with an advancing water contact angle of up to 143°) was obtained, and the degree of hydrophobicity was found to be dependent on the particle size and concentration of the dip-coating solution. UV-vis spectra showed nearly 100% transmission in the visible region from the glass coated with dual-scale nanoparticles, similar to the bare one. The coating strategy was versatile, and superhydrophobicity was obtained on various substrates, including Si, glass, epoxy resin, and fabrics. Thermal annealing enhanced the stability of the nanoparticle coating, and superhydrophobicity was maintained against prolonged exposure to UV light under ambient conditions.     

Versatile wet-chemical synthesis of non-agglomerated CaCO3 vaterite nanoparticles

Calcium carbonate (vaterite) nanoparticles of 20-60 nm size were obtained without stabilizing tensides by heating a dispersion of calcium bicarbonate (CaHCO(3)) in ethylene glycol for 30 minutes at 40 to 100 °C.     

Au nanoparticle monolayers covered with sol-gel oxide thin films: optical and morphological study

In this work, we provide a detailed study of the influence of thermal annealing on submonolayer Au nanoparticle deposited on functionalized surfaces as standalone films and those that are coated with sol-gel NiO and TiO(2) thin films. The systems are characterized through the use of UV-vis absorption, X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), and spectroscopic ellipsometry. The surface plasmon resonance peak of the Au nanoparticles was found to red-shift and increase in intensity with increasing surface coverage, an observation that is directly correlated to the complex refractive index properties of Au nanoparticle layers. The standalone Au nanoparticles sinter at 200 °C, and a relationship between the optical properties and the annealing temperature is presented. When overcoated with sol-gel metal oxide films (NiO, TiO(2)), the optical properties of the Au nanoparticles are strongly affected by the metal oxide, resulting in an intense red shift and broadening of the plasmon band; moreover, the temperature-driven sintering is strongly limited by the metal oxide layer. Optical sensing tests for ethanol vapor are presented as one possible application, showing reversible sensing dynamics and confirming the effect of Au nanoparticles in increasing the sensitivity and in providing a wavelength dependent response, thus confirming the potential use of such materials as optical probes.     

Synthesis of gold@carbon dots composite nanoparticles for surface enhanced Raman scattering

Gold@carbon dots composite nanoparticles (Au@CDs) with ultrathin carbon dot (CD) shells of ca. 2 nm were prepared by reducing HAuCl(4) with CDs at 100 °C. By adjusting the feeding mass ratio of HAuCl(4) to CDs, the average diameters of Au@CDs can be modulated from 8 to 44 nm. The suspension of Au@CDs with an average diameter of ca. 24 nm was applied as a substrate for surface enhanced Raman scattering (SERS) and it exhibited a higher SERS effect for rhodamine 6G (Rh6G) than the suspension of pure Au nanoparticles with nearly the same size. The excellent SERS effect of Au@CDs is mainly attributed to their improved capability of adsorbing the aromatic probe molecules.     

On the morphology and stability of Au nanoparticles on TiO2(110) prepared from micelle-stabilized precursors

The morphology and stability of well-ordered, nanostructured Au/TiO2(110) surfaces, prepared by deposition of Au loaded micelles on TiO2(110) substrates and subsequent oxidative removal of the polymer shell in an oxygen plasma, was investigated by noncontact AFM, SEM and XPS. The resulting arrays of Au nanoparticles (particle sizes 1-5 nm) form a nearly hexagonal pattern with well-defined interparticle distances and a narrow particle size distribution. Particle size and particle separation can be controlled independently by varying the Au loading and the block-copolymers in the micelle shell. The oxygen plasma treatment does not affect the size and distance of the Au nanoparticles; the latter are fully metallic after subsequent UHV annealing (400 degrees C). The particles are stable under typical CO oxidation reaction conditions, up to at least 200 degrees C, making these surfaces ideally suited as defined model systems for catalytic studies. Significant changes in the height distributions of the Au nanoparticles are found upon 400 degrees C annealing in O2. For adlayers with small interparticle distances, this leads to a bimodal particle size distribution, which together with the preservation of the lateral order points to Ostwald ripening.     

Low-temperature preparation of highly conductive thin films from acrylic acid-stabilized silver nanoparticles prepared through ligand exchange

The preparation of AcA-stabilized Ag nanoparticles and its application to make highly conductive thin films are reported. The AcA-stabilized Ag nanoparticles were prepared through a ligand exchange of original oleylamine (OLA)-coated Ag nanoparticles with acrylic acid (AcA), which acted as both an antisolvent and a modifying ligand during the ligand exchange process. Efficiencies of the ligand exchange as well as the properties of Ag nanoparticles were analyzed using various techniques including TEM, FT-IR, XPS, TGA, and UV-vis methods. The thin films were fabricated by annealing spin-coated AcA-stabilized Ag nanoparticles. Further, the effects of annealing temperature, time, and film thickness on both the film morphology and electrical conductivity have been investigated. In this work, due to the low boiling temperature of stabilizer (AcA) and adjustment of annealing conditions, high electrical conductivity was obtained for the Ag thin films. For example, when annealing at 175 °C for 30 min, a 70 nm thick film showed a maximum electrical conductivity of 1.12 × 10(5) S cm(-1). A conductive layer on a flexible polymer substrate (e.g., PET) sheet has been successfully prepared by annealing a spin-coated film at 140 °C for 30 min. The combined advantages of long-term stability of the AcA-stabilized Ag nanoparticles, low annealing temperature, and high conductivity of the prepared thin films make this relatively simple method attractive for applications in flexible electronics.     

Morphology of gold nanoparticles synthesized by filamentous cyanobacteria from gold(I)-thiosulfate and gold(III)--chloride complexes

Plectonema boryanum UTEX 485, a filamentous cyanobacterium, has been reacted with aqueous Au(S(2)O(3))(2)(3)(-) and AuCl(4)(-) solutions ( approximately 400-550 mg/L Au) at 25-100 degrees C for up to 1 month and at 200 degrees C for 1 day. The interaction of cyanobacteria with aqueous Au(S(2)O(3))(2)(3)(-) promoted the precipitation of cubic (100) gold nanoparticles (<10-25 nm) at membrane vesicles and admixed with gold sulfide within cells and encrusted on the cyanobacteria, whereas reaction with AuCl(4)(-) resulted in the precipitation of octahedral (111) gold platelets ( approximately 1-10 microm) in solutions and nanoparticles of gold (<10 nm) within bacterial cells. Functional groups imaged by negative ion TOF-SIMS on (111) faces of the octahedral platelets were predominantly Cl and CN, with smaller amounts of C(2)H and CNO.     

Construction of sensitive and selective zirconia-based CO sensors using ZnCr2O(4)-based sensing electrodes

The carbon monoxide (CO) sensitivity of a mixed-potential-type yttria-stabilized zirconia (YSZ)-based tubular-type sensor utilizing a ZnCr(2)O(4) sensing electrode (SE) was tuned by the addition of different precious metal nanoparticles (Ag, Au, Ir, Pd, Pt, Ru and Rh; 1 wt % each) into the sensing layer. After measuring the electromotive force (emf) response of the fabricated SEs to 100 ppm of CO against a Pt/air-reference electrode (RE), the ZnCr(2)O(4)-Au nanoparticle composite electrode (ZnCr(2)O(4)(+Au)-SE) was found to give the highest response to CO. A linear dependence on the logarithm of CO concentration in the range of 20-800 ppm at an operational temperature of 550 °C under humid conditions (5 vol % water vapor) was observed. From the characterization of the ZnCr(2)O(4)(+Au)-SE, we can conclude that the engineered high response toward CO originated from the specific properties of submicrometer sized Au particles, formed via the coalescence of nanosized Au particles located on ZnCr(2)O(4) grains, during the calcining process at 1100 °C for 2 h. These particles augmented the catalytic activities of the gas-phase CO oxidation reaction in the SE layer, as well as to the anodic reaction of CO at the interface; while suppressing the cathodic reaction of O(2) at the interface. In addition, the response of the ZnCr(2)O(4)(+Au)-SE sensor toward 100 ppm of CO gradually increased throughout the 10 days of operation, and plateaued for the remainder of the month that the sensor was examined. Correlations between SEM observations and the CO sensing characteristics of the present sensor were suggestive that the sensitivity was mostly affected by the morphology of the Au particles and their catalytic activities, which were in close proximity to the ZnCr(2)O(4) grains. Furthermore, by measuring the potential difference (emf) between the ZnCr(2)O(4)(+Au) and a ZnCr(2)O(4) electrode, sensitivities to typical exhaust component gases other than CO were found to be negligible at 550 °C.     

Comparison between measurements of elasticity and free amino group content of ovalbumin microcapsule membranes: discrimination of the cross-linking degree

Gold nanoparticle-doped poly(2-vinylpyridine) (P2VP) microcapsules and foam films were synthesized and assembled at the P2VP chloroform solution/HAuCl(4) aqueous solution interface at 25 °C. It was found that Au nanoparticles with the average diameter of 2.1 nm were homogeneously embedded in and adsorbed on the walls of the capsules and foams, the nanoparticles were composed of Au(0) and Au(III) with the molar ratio of about 75/25, and the mass percent of Au elements was measured to be 19.65%. The formation of the nanostructures was attributed to the self-assembly of P2VP at the liquid/liquid interface, the simultaneous reduction of AuCl(4)(-) ions by a small amount of ethanol in the chloroform and adsorption of AuCl(4)(-) ions. After irradiated by UV-light for 1h, the average diameter of the nanoparticles was found to be 2.2 nm, and the AuCl(4)(-) ions were transformed to Au(0) completely. The catalytic performance of these composite nanostructures were evaluated by using the reduction of 4-nitrophenol (4-NP) by potassium borohydride in aqueous solutions. The catalytic activity was very high in the first cycle, decreased rapidly and slightly in the second and third cycles, respectively, due to the aggregation of some nanoparticles, and stabilized after the third cycle.     

In situ coarsening study of inverse micelle-prepared Pt nanoparticles supported on γ-Al2O3: pretreatment and environmental effects

The thermal stability of inverse micelle prepared Pt nanoparticles (NPs) supported on nanocrystalline γ-Al(2)O(3) was monitored in situ under different chemical environments (H(2), O(2), H(2)O) via extended X-ray absorption fine-structure spectroscopy (EXAFS) and ex situ via scanning transmission electron microscopy (STEM). Drastic differences in the stability of identically synthesized NP samples were observed upon exposure to two different pre-treatments. In particular, exposure to O(2) at 400 °C before high temperature annealing in H(2) (800 °C) was found to result in the stabilization of the inverse micelle prepared Pt NPs, reaching a maximum overall size after moderate coarsening of ～1 nm. Interestingly, when an analogous sample was pre-treated in H(2) at ～400 °C, a final size of ～5 nm was reached at 800 °C. The beneficial role of oxygen in the stabilization of small Pt NPs was also observed in situ during annealing treatments in O(2) at 450 °C for several hours. In particular, while NPs of 0.5 ± 0.1 nm initial average size did not display any significant sintering (0.6 ± 0.2 nm final size), an analogous thermal treatment in hydrogen leads to NP coarsening (1.2 ± 0.3 nm). The same sample pre-dosed and annealed in an atmosphere containing water only displayed moderate sintering (0.8 ± 0.3 nm). Our data suggest that PtO(x) species, possibly modifying the NP/support interface, play a role in the stabilization of small Pt NPs. Our study reveals the enhanced thermal stability of inverse micelle prepared Pt NPs and the importance of the sample pre-treatment and annealing environment in the minimization of undesired sintering processes affecting the catalytic performance of nanosized particles.     

Formation of Metal Selenide and Metal–Selenium Nanoparticles using Distinct Reactivity between Selenium and Noble Metals

Small Se nanoparticles with a diameter of ≈20 nm were generated by the reduction of selenium chloride with NaBH₄ at ?10 °C. The reaction with Ag at 60 °C yielded stable Ag₂Se nanoparticles, which subsequently were transformed into M–Se nanoparticles (M=Cd, Zn, Pb) through cation exchange reactions with corresponding ions. The reaction with Pt formed Pt layers that were evenly coated on the surface of the Se nanoparticles, and the dissolution of the Se cores with hydrazine generated uniform Pt hollow nanoparticles. The reaction with Au generated tiny Au clusters on the Se surface, and eventually formed acorn‐shaped Au–Se nanoparticles through heat treatment. These results indicate that small Se nanoparticles with diameters of ≈20 nm can be used as a versatile platform for the synthesis of metal selenide and metal–selenium hybrid nanoparticles with complex structures.     

Synthesis of silica supported AuCu nanoparticle catalysts and the effects of pretreatment conditions for the CO oxidation reaction

Supported gold nanoparticles have generated an immense interest in the field of catalysis due to their extremely high reactivity and selectivity. Recently, alloy nanoparticles of gold have received a lot of attention due to their enhanced catalytic properties. Here we report the synthesis of silica supported AuCu nanoparticles through the conversion of supported Au nanoparticles in a solution of Cu(C(2)H(3)O(2))(2) at 300 °C. The AuCu alloy structure was confirmed through powder XRD (which indicated a weakly ordered alloy phase), XANES, and EXAFS. It was also shown that heating the AuCu/SiO(2) in an O(2) atmosphere segregated the catalyst into a Au-CuO(x) heterostructure between 150 °C to 240 °C. Heating the catalyst in H(2) at 300 °C reduced the CuO(x) back to Cu(0) to reform the AuCu alloy phase. It was found that the AuCu/SiO(2) catalysts were inactive for CO oxidation. However, various pretreatment conditions were required to form a highly active and stable Au-CuO(x)/SiO(2) catalyst to achieve 100% CO conversion below room-temperature. This is explained by the in situ FTIR result, which shows that CO molecules can be chemisorbed and activated only on the Au-CuO(x)/SiO(2) catalyst but not on the AuCu/SiO(2) catalyst.     

Electropolymerized network of polyamidoamine dendron-coated gold nanoparticles as novel nanostructured electrode surface for biosensor construction

Polyfuntionalized gold nanoparticles were prepared by using 2-mercaptoethanesulfonic acid, p-aminothiophenol and cysteamine core polyamidoamine G-4 dendron as capping ligands. The nanoparticles were electropolymerized on a Au electrode surface through the formation of a bisaniline-cross-linked network. The enzyme tyrosinase was further crosslinked on this nanostructured matrix. The enzyme electrode, poised at -100 mV, was used for the amperometric quantification of cathecol. The biosensor showed a linear response from 50 nM to 10 μM cathecol, with a low detection limit of 20 nM and a sensitivity of 1.94 A M(-1) cm(2). The electrode retained 96% and 67% of its initial activity after 16 and 30 days of storage at 4 °C under dry conditions.     

Influence of hydrophobic alkylated gold nanoparticles on the phase behavior of monolayers of DPPC and clinical lung surfactant

The effect of hydrophobic alkylated gold nanoparticles (Au NPs) on the phase behavior and structure of Langmuir monolayers of dipalmitoylphosphatidylcholine (DPPC) and Survanta, a naturally derived commercial pulmonary surfactant that contains DPPC as the main lipid component and hydrophobic surfactant proteins SP-B and SP-C, has been investigated in connection with the potential implication of inorganic NPs in pulmonary surfactant dysfunction. Hexadecanethiolate-capped Au NPs (C(16)SAu NPs) with an average core diameter of 2 nm have been incorporated into DPPC monolayers in concentrations ranging from 0.1 to 0.5 mol %. Concentrations of up to 0.2 mol % in DPPC and 16 wt % in Survanta do not affect the monolayer phase behavior at 20 °C, as evidenced by surface pressure-area (π-A) and ellipsometric isotherms. The monolayer structure at the air/water interface was imaged as a function of the surface pressure by Brewster angle microscopy (BAM). In the liquid-expanded/liquid-condensed phase coexistence region of DPPC, the presence of 0.2 mol % C(16)SAu NPs causes the formation of many small, circular, condensed lipid domains, in contrast to the characteristic larger multilobes formed by pure lipid. Condensed domains of similar size and shape to those of DPPC with 0.2 mol % C(16)SAu NPs are formed by compressing Survanta, and these are not affected by the C(16)SAu NPs. Atomic force microscopy images of Langmuir-Schaefer-deposited films support the BAM observations and reveal, moreover, that at high surface pressures (i.e., 35 and 45 mN m(-1)) the C(16)SAu NPs form honeycomb-like aggregates around the polygonal condensed DPPC domains. In the Survanta monolayers, the C(16)SAu NPs were found to accumulate together with the proteins in the liquid-expanded phase around the circular condensed lipid domains. In conclusion, the presence of hydrophobic C(16)SAu NPs in amounts that do not influence the π-A isotherm alters the nucleation, growth, and morphology of the condensed domains in monolayers of DPPC but not of those of Survanta. Systematic investigations of the effect of the interaction of chemically defined NPs with the lipid and protein components of lung surfactant on the physicochemical properties of surfactant films are pertinent to understanding how inhaled NPs impact pulmonary function.     

Chloroform-Enhanced Incorporation of Hydrophobic Gold Nanocrystals into Dioleoylphosphatidylcholine (DOPC) Vesicle Membranes

Vesicles of dioleoylphosphatidylcholine (DOPC) formed by extrusion (liposomes) with hydrophobic alkanethiol-capped Au nanocrystals were studied. Dodecanethiol-capped 1.8-nm-diameter Au nanocrystals accumulate in the lipid bilayer, but only when dried lipid-nanocrystal films were annealed with chloroform prior to hydration. Without chloroform annealing, the Au nanocrystals phase separate from DOPC and do not load into the liposomes. Au nanocrystals with slightly longer capping ligands of hexadecanethiol or with a larger diameter of 4.1 nm disrupted vesicle formation and created lipid assemblies with many internal lamellar attachments.     

Luminescent silicate core-shell nanoparticles: synthesis, functionalization, optical, and structural properties

SiO(2)/Zn(2)SiO(4):Mn(2+) core-shell nanoparticles with mean diameters in the range of 55-220 nm were prepared by a modified Pechini sol-gel method followed by lyophilization and annealing at temperatures of 800-1100°C. The as-synthesized nanoparticles were characterized by transmission electron microscopy, X-ray diffraction analysis, and photoluminescence spectroscopy. The results demonstrate that the crystal structure of the shell and the optical properties can be tuned by the annealing temperature and a variation of the concentration of doping ions. Under UV excitation, the samples emit green luminescence with its maximum at 525 nm, typical for the Mn(2+) ions in α-Zn(2)SiO(4). The resulting nanoparticles were successfully modified with amine and carboxyl functions with respect to a later attachment of biological moieties.     

应用功能化的金纳米通道分离阿特拉津和百草枯

将金(Ⅰ)通过化学沉积法于4℃经9h使之沉积于聚碳酸酯滤膜(孔径100nm)的内孔壁上,从而制得金纳米通道膜。经清洗并干燥后的膜在十八烷基硫醇[CH3(CH2)16CH2SH](0.1+99.9)溶液中浸泡12h,从而使金纳米通道膜被十八烷基硫醇修饰(将此膜简写作C18SH-Mem)并使其呈疏水性。试验在分离装置的样品池中加入阿特拉津和百草枯两种农药的混合溶液,并使其通过C18H37SH-Mem,经过一定时间后,在膜另一端的检测池中对上述两农药分别在222nm及257nm波长处进行检测。结果表明:在检测池中只测得疏水性的阿特拉津而未能测得百草枯,说明亲水性的百草枯不能在疏水性的经修饰的金纳米通道中迁移。据此,应用修饰后的金纳米通道可达到上述两农药的完全分离。