Electrophoretic deposition of TiO2 nanoparticles using organic dyes

Electrophoretic deposition method has been developed for the deposition of TiO(2) nanoparticles modified with organic dyes. Alizarin red, alizarin yellow and pyrocatechol violet dyes were used for the dispersion and charging of TiO(2) in ethanol and anodic electrophoretic deposition of TiO(2) films. The deposition yield was varied by the variation of dye concentration in suspensions and deposition time. Aurintricarboxylic acid dye was used for the deposition of TiO(2) from aqueous suspensions. It was found that thin films of pure aurintricarboxylic acid and composite aurintricarboxylic acid TiO(2) films can be obtained. The deposition yield was studied by quartz crystal microbalance. Dye film thickness was varied in the range of 0.1-2 μm by variation in the deposition time at a constant voltage. The composition of the films and the amount of the deposited material can be varied by the variation of TiO(2) and dye concentration in suspensions and deposition time. The films were studied by Fourier transform infrared spectroscopy, thermogravimetric analysis, differential thermal analysis and electron microscopy. The deposition mechanisms were discussed. The electrophoretic deposition method offers advantages for the fabrication of dye-sensitized TiO(2) films.     

Site-selective direct photochemical deposition of copper on glass substrates using TiO2 nanocrystals

Deposition of copper thin films was achieved by a photocatalytic reaction of site-selectively adsorbed TiO(2) nanocrystals for direct fabrication of copper circuit patterns on glass substrates. The nanocrystal monolayers absorbed on hydrophobic surface templates serve as an effective photocatalyst, producing metallic copper and formic acid via oxidation of methanol in solution. The formic acid generated has also been suggested to serve as an electron donor that accelerates copper deposition through a UV-mediated autocatalytic reaction, even after nanocrystals are embedded into the grown copper films. The thickness of the deposited copper films was easily controlled by varying the UV irradiation time, irradiation power, and initial concentration of methanol as a hole scavenger. The process presented herein provides an effective methodology for resist-free, direct metallization of insulating substrates.     

Controlled electrophoretic deposition of uniquely nanostructured star polymer films

The controlled electrophoretic deposition of polystyrene/divinylbenzene (PS/DVB) star polymer films from a colloidal suspension is reported. Liquid suspensions, containing the PS/DVB star polymer, were prepared by injecting a dichloromethane (DCM) solution of the star polymer into a stratified liquid combination of hexane and DCM. A variety of hexane/DCM volume ratios were examined to identify the optimal solution conditions for electrophoretic deposition; thin films were produced from both unmixed and well-mixed hexane/DCM suspensions. Unmixed suspensions yielded spatially separated thin films, deposited in a controlled fashion, that were dependent on the polarity of the corresponding electrode. Films on the positive electrode differed in thickness, microstructure, and appearance from those formed on the negative electrode. In contrast, films produced from well-mixed hexane/DCM suspensions deposited uniformly across only the negative electrode. Atomic force microscopy studies revealed nanostructured surface morphologies that were unique to each of these films. Additionally, these microscopy studies shed light on the possible conformations of star polymers adsorbed on a surface. By controlling the composition and the mixing state of the solution and by controlling the bias of electrodes, we achieved controlled deposition of star polymer films with a specific nanostructure. These nanostructured films may have broad use in optical and biological device applications.     

阳极氧化TiN薄膜制备N掺杂纳米TiO2薄膜及其可见光活性

室温下通过电泳沉积(EPD)的方法在Ti片表面制备TiN薄膜, 然后对TiN薄膜进行阳极氧化得到N掺杂多孔纳米结构的TiO2薄膜. 利用X射线衍射(XRD), X射线光电子能谱(XPS), 扫描电子显微镜(SEM)及光电化学方法对得到的薄膜进行表征. XRD测试结果表明, 经过阳极氧化并在350 ℃空气气氛中退火1 h的薄膜中存在锐钛矿晶型的TiO2. XPS的结果表明, 样品中的N元素取代部分O, 且N的摩尔分数为0.95%. SEM显示, 经阳极氧化后薄膜表面出现多孔纳米结构. 光电化学测试结果显示, 阳极氧化提高了N掺杂TiO2薄膜在可见光下的光电响应. 经阳极氧化并热处理的薄膜在0 V电位及可见光照射下光电流密度为2.325 μA·cm-2, 而单纯热处理的薄膜在相同条件下光电流密度仅为0.475 μA·cm-2. 阳极氧化得到纳米多孔结构提高了N掺杂纳米TiO2薄膜的表面积, 从而对可见光的响应增大.     

Influence of ordering in porous TiO2 layers on electron diffusion

Layers of porous TiO(2) fabricated by electrophoretic deposition at different temperatures with subsequent sintering in air were investigated by transient photocurrent measurements in aqueous electrolyte. The effective diffusion coefficient of excess electrons changed between 1.6 x 10(-5) and 1.4 x 10(-4) cm(2)/s depending strongly on the solution temperature during the TiO(2) layer deposition. Characterization, in terms of average degree of preferred orientation, shows that low deposition temperature results in orientation of the nanocrystals forming the porous film. Consequently, the increase of effective diffusion coefficient is attributed to a higher degree of ordering in the nanoporous TiO(2) layer.     

Selective atomic layer deposition of titanium oxide on patterned self-assembled monolayers formed by microcontact printing

We demonstrate a selective atomic layer deposition of TiO2 thin films on patterned alkylsiloxane self-assembled monolayers. Microcontact printing was done to prepare patterned monolayers of the alkylsiloxane on Si substrates. The patterned monolayers define and direct the selective deposition of the TiO2 thin film using atomic layer deposition. The selective atomic layer deposition is based on the fact that the TiO2 thin film is selectively deposited only on the regions exposing the silanol groups of the Si substrates because the regions covered with the alkylsiloxane monolayers do not have any functional group to react with precursors.     

水溶液法制备图案化TiO2薄膜

从硫酸钛Ti(SO4)2的水溶液出发, 采用化学浴沉积和电沉积法来制备图案化TiO2薄膜. 通过硫酸和双氧水来稳定Ti4+, 配制了pH=1.0的硫酸钛溶液和pH=1.6的过氧硫酸钛溶液. 结合微接触印刷术在硅基底上制得自组装膜预图案, 再化学浴沉积TiO2即可得规则图纹. 无机配体对钛溶液的稳定性和TiO2的晶型均有影响, 溶液的酸度关系到所得图案的质量. 过氧硫酸钛溶液同样适用于电沉积, 在导电玻璃基底上旋涂光刻胶后选择性曝光、显影, 通过控制阴极电位可获得高差达200 nm的清晰图案.     

A new patterning method using photocatalytic lithography and selective atomic layer deposition

We report a new patterning method using photocatalytic lithography of alkylsiloxane self-assembled monolayers and selective atomic layer deposition of thin films. The photocatalytic lithography is based on the fact that the decomposition rate of the alkylsiloxane monolayers in contact with TiO2 is much faster than that with SiO2 under UV irradiation in air. The photocatalytic lithography, using a quartz plate coated with patterned TiO2 thin films, was done to prepare patterned monolayers of the alkylsiloxane on Si substrates. A ZrO2 thin film was selectively deposited onto the monolayer-patterned Si substrate by atomic layer deposition.     

Alternating current electrophoretic deposition (EPD) of TiO2 nanoparticles in aqueous suspensions

TiO(2)-nanostructured coatings from aqueous suspensions have been successfully prepared by the application of alternating current (AC) instead of direct current (DC) during electrophoretic deposition (EPD). No organic additives in suspension were required for successful EPD. The quality of the AC-EPD TiO(2) coatings in terms of homogeneity and extent of microcracking, upon drying, observed by SEM, was superior to that of DC-EPD coatings made from the same type of suspensions. The main difference between AC- and DC-EPD was the suppression of bubble formation. The absence of water electrolysis at the electrodes can be explained by the particular distribution of the electric field during AC mode, which prevents the nucleation of bubbles. The preparation of TiO(2) coatings from aqueous suspension and without the aid of organic stabilizers opens the possibility for co-deposition of sensitive materials such as biomolecules and even cells for biomedical applications, given the high biocompatibility of TiO(2). The deposition of TiO(2) coatings from aqueous suspensions is also attractive from environmental and economical points of view.     

Methods for functionalization of microsized polystyrene beads with titania nanoparticles for cathodic electrophoretic deposition

Functionalization of colloidal particles based on the use of polyelectrolytes and heterocoagulation was combined with electrophoretic deposition (EPD), with the aim of depositing titania-polystyrene (TiO(2)-PS) composite particles on Ti6Al4V substrates. The composite particles were obtained by heterocoagulation of TiO(2) nanoparticles on the surface of monosized polystyrene beads of 4.6 microm in diameter. Two alternative methods were developed for the preparation of the TiO(2)-PS suspensions in organic fluids for cathodic electrodeposition. The first method was carried out in alkaline aqueous medium with the use of polyelectrolytes and intermediate control measurements of zeta potential, conductivity, and pH; the second one was carried out directly in the organic solvent used for EPD, typically isopropanol. Examples of deposits obtained by EPD in both suspensions and a comparative analysis between the two methods are presented.     

Pure-silica-zeolite MEL low-k films from nanoparticle suspensions

Following our previous works on pure-silica-zeolite (PSZ) MFI, in this study we explore PSZ MEL as a new option for low-k dielectric films. Our motivation has been to increase the microporosity of the spin-on films by moving to structures with a framework density (FD) lower than MFI. Nanoparticle PSZ MEL suspensions were synthesized by a two-stage method that allowed the yield of nanocrystals to be significantly enhanced, while the zeolite nanocrystals remain small. For the first time zeolite nanocrystals of about 50 nm were synthesized with a yield as high as 57%. Nanoparticle suspensions with different particle sizes and crystallinities were spun on silicon wafers to prepare continuous thin films. An ultralow-k value as low as 1.5 was obtained with MEL nanoparticle suspension of high relative crystallinity. The surface roughness of the PSZ MEL film with high relative crystallinity is greatly improved (R(rms) approximately 5.6 nm) compared to MFI films with high relative crystallinity (R(rms) approximately 12 nm).     

Activation of high-TC ferromagnetism in Co2+:TiO2 and Cr3+:TiO2 nanorods and nanocrystals by grain boundary defects

Colloidal Co(2+)- and Cr(3+)-doped TiO(2) nanorods and nanocrystals were synthesized and studied by X-ray powder diffraction, electronic absorption spectroscopy, magnetic circular dichroism spectroscopy, magnetic susceptibility, and transmission electron microscopy. The nanorods were paramagnetic as colloids but showed room-temperature ferromagnetism when spin-coated aerobically into films. Crystalline domain size, thermal annealing, and dopant or defect migration are not the dominating factors converting the doped TiO(2) nanocrystals from the paramagnetic state to the ferromagnetic state. The most important factor for activating ferromagnetism is found to be the creation of grain boundary defects, proposed to be oxygen vacancies at nanocrystal fusion interfaces. These defects are passivated and the ferromagnetism destroyed by further aerobic annealing. These results not only help elucidate the origins of the TM(n+):TiO(2) DMS ferromagnetism but also represent an advance toward the controlled manipulation of high-T(C) DMS ferromagnetism using external chemical perturbations.     

水溶液法制备图案化TiO_2薄膜

从硫酸钛Ti(SO4)2的水溶液出发,采用化学浴沉积和电沉积法来制备图案化TiO2薄膜.通过硫酸和双氧水来稳定Ti4+,配制了pH=1.0的硫酸钛溶液和pH=1.6的过氧硫酸钛溶液.结合微接触印刷术在硅基底上制得自组装膜预图案,再化学浴沉积TiO2即可得规则图纹.无机配体对钛溶液的稳定性和TiO2的晶型均有影响,溶液的酸度关系到所得图案的质量.过氧硫酸钛溶液同样适用于电沉积,在导电玻璃基底上旋涂光刻胶后选择性曝光、显影,通过控制阴极电位可获得高差达200nm的清晰图案.     

Lead Sulfide Nanocrystal-Polymer Composites for Optoelectronic Applications

Summary: Nanocomposite films were prepared by two methods in which lead sulfide (PbS) nanocrystals were contained in an organic matrix. One method used a wet chemical synthesis of the nanocrystals in the direct presence of a polymer, where the polymer controlled nanocrystal growth. The second method was gaseous deposition of nanocrystals into the organic phase. The two methods were similar in that the nanocrystals in the composites were free from surfactant capping layers that otherwise would add an interfacial region between the nanocrystal and the organic matrix. The gaseous deposition technique had several advantages over the wet chemical synthesis in that it allowed direct control over nanocrystal size and density, improved flexibility in the choice of organic phase, and was compatible with lithographic methods.     

Langmuir--Schaefer films of Nafion with incorporated TiO(2) nanoparticles

An easy method of incorporating TiO(2) nanoparticles into Nafion perfluorinated ionomer is proposed. Ultrathin films of Nafion were prepared by employing the Langmuir-Schaefer (LS) technique. The pressure-area isotherm study of a Langmuir monolayer of Nafion at the air-water interface on different concentrations of NaCl as the subphase allowed us to find the best experimental conditions for the deposition of stable Langmuir-Schaefer films. Incorporation of TiO(2) nanoparticles was performed by dipping Nafion LS films in a solution of TiO(2) nanoparticles. The uniformity of the TiO(2) incorporation was detected by UV-visible spectroscopy. The morphology of the Nafion, Nafion/TiO(2) nanoparticles thin films, and the changes due to the annealing procedure were investigated by atomic force microscopy. Interestingly, the AFM investigation showed that Nafion and Nafion/TiO(2) LS films have thermal stability up to 600 degrees C.     

Kinetics of adsorption of oxalic acid on different titanium dioxide samples

FTIR-ATR kinetic studies on the adsorption of oxalic acid on different TiO(2) films were performed. The particulate films were obtained through the evaporation of TiO(2) suspensions. The evolution of the IR bands followed a pseudo-first-order behavior, as previously observed. Systematic studies as a function of the oxalic acid concentration afforded the specific rate constant for adsorption (k(a)) and desorption (k(d)). The influence of physical parameters of the samples, i.e., specific BET area, crystalline domain size, TiO(2) load, film area, and pore size, on the kinetic parameters k(a) and k(d) was analyzed. A mechanism in which the adsorption and desorption processes are controlled by the diffusion through the pores of the films is proposed (intraparticle diffusion). It is concluded that all the samples behave in the same way. Thicker films or those with smaller particle size (higher specific surface area, smaller pores) show the slowest rates of adsorption and desorption. These results are relevant for the design of efficient heterogeneous catalysts and sensors, and for the interpretation of pollutant adsorption.     

Photocatalytic patterning of monolayers for the site-selective deposition of quantum dots onto TiO2 surfaces

A novel photochemical mechanism is reported for the site-selective deposition of quantum dots onto nanocrystalline TiO2 films. The patterning mechanism involves the combination of surfactant-mediated self-assembly and monolayer photolithography. In the self-assembly process, CdS and CdSe quantum dots were attached to TiO2 surfaces through bifunctional mercaptoalkanoic acid (MAA) linkers. MAAs were adsorbed to the TiO2 surface as the deprotonated carboxylates, primarily through monodentate coordination to Ti4+ sites. CdSe quantum dots were bound to the terminal thiol groups of surface-adsorbed MAAs, with a surface adduct formation constant, Kad, of (2.1 +/- 0.7) x 104 M-1. The color and optical density of the quantum dot-functionalized TiO2 films were tunable. Monolayer photopatterning involved the TiO2-catalyzed oxidative degradation of surface-adsorbed mercaptohexadecanoic acid (MHDA). A mechanism is proposed wherein MHDA degradation occurs through both oxidative decarboxylation and the formation of interchain disulfides. These MHDA photodegradation processes regulate the extent to which CdSe quantum dots adsorb onto the TiO2 surface. Illumination through a photomask yielded optically patterned, quantum dot-functionalized TiO2 films that were characterized by scanning electron microscopy and energy-dispersive X-ray analysis.     

Internal structure of nanoporous TiO2/polyion thin films prepared by layer-by-layer deposition

The internal structure of porous TiO2 films prepared by electrostatic layer-by-layer deposition was investigated. The films were prepared by alternate dipping of solid substrates into dispersions of TiO2 nanoparticles and polycations, polyanions, or pure buffer solution, respectively. The surface charge of the amphoteric TiO2 particles was controlled by the pH of the aqueous dispersions. The morphology of the film surface was investigated by means of scanning electron microscopy. It was found that the surface roughness strongly depends on the polymeric material used for the deposition process but is independent of the ionic strength of the solution or the molecular weight of the polyions. The samples with rough surfaces feature strong light scattering. The porosity and internal structure of the TiO2/polyelectrolyte films were investigated by adsorption/desorption of dye molecules. A crude estimate yields an internal surface that is up to 160 times the plane surface of the substrate for a film thickness of 1 microm. The composition of the films was investigated by X-ray photoelectron spectroscopy (XPS). Detection of the XPS signal after each deposition step of the first three dipping cycles shows a significant increase of the relative surface coverage of Ti after the TiO2 deposition step and of PSS after the PSS deposition step. For later dipping cycles, such an increase was also detectable but less prominent.     

Mobility enhanced photoactivity in sol-gel grown epitaxial anatase TiO2 films

Epitaxial anatase thin films were grown on single-crystal LaAlO3 substrates by a sol-gel process. The epitaxial relationship between TiO2 and LaAlO3 was found to be [100]TiO2||[100]LaAlO3 and (001)TiO2||(001)LaAlO3 based on X-ray diffraction and a high-resolution transmission electron microscopy. The epitaxial anatase films show significantly improved photocatalytic properties, compared with polycrystalline anatase film on fused silica substrate. The increase in the photocatalytic activity of epitaxial anatase films is explained by enhanced charge carrier mobility, which is traced to the decreased grain boundary density in the epitaxial anatase film.     

Preillumination of TiO2 and Ta2O5 photoactive thin films as a tool to tailor the synthesis of composite materials

Illumination of TiO 2 thin films with UV light is known to induce the transformation of the surface of this material from partially hydrophobic into fully hydrophilic. The present work shows that this transformation is accompanied by other effects that may be used to control the synthesis of composite materials. For this purpose, TiO 2 and Ta 2O 5 transparent thin films with a columnar structure and open pores were prepared by electron evaporation at glancing angles. Transparent TiO 2 thin films with micropores (i.e., pores smaller than 2 nm) prepared by plasma enhanced chemical vapor deposition (PECVD) were also used. All these films became hydrophilic upon UV illumination. Rhodamine 6G and Rhodamine 800 dyes were irreversibly adsorbed within the columns of the TiO 2 and Ta 2O 5 thin films by immersion into a water solution of these molecules. Isolated and aggregated molecules of these two dyes were detected by visible absorption spectroscopy. The infiltration adsorption efficiency was directly correlated with the acidity of the medium, increasing at basic pHs as expected from simple considerations based on the concepts of the point of zero charge (PZC) in colloidal oxides. The infiltration experiments were repeated with columnar TiO 2 and Ta 2O 5 thin films that were subjected to preillumination with UV light. It was found that this treatment produced a modification in the type (isolated or aggregated) and amount of dye molecules incorporated into the pores. Moreover, the selective adsorption of a given dye in preilluminated areas of the films permitted the lithographic coloring of the films. Preillumination also controls the UV induced deposition of silver on the surface of the microporous TiO 2 thin films. It was found that the size distribution of the formed silver nanoparticles was dependent on the preillumination treatment and that a well-resolved surface plasmon resonance at around 500 nm was only monitored in the preilluminated films. A model is proposed to account for the effects induced by UV preillumination on the TiO 2 and Ta 2O 5 oxide surfaces. The possibilities of this type of light treatment for the tailored synthesis of nanocomposite thin films (i.e., dye-oxide, metal nanoparticles-oxide) are highlighted.