Deposition of silver nanoparticles on cellulosic fibers via stabilization of carboxymethyl groups

The stabilizing role of carboxymethyl groups on the conformal deposition of Ag NPs over cellulosic fibers was elucidated while developing a method for the deposition of silver nanoparticles (NPs) on cellulose acetate (CA), cellulose and partially carboxymethylated cellulose (CMC) electrospun fibers. CMC fibers were prepared through judicious anionization of deacetylated cellulose acetate fibers. Ag NPs were chemically reduced from silver nitrate using sodium borohydride and further stabilized using citrate. Ag NPs were directly deposited onto CA, cellulose and CMC electrospun fibers at pH conditions ranging from 2.5 to 9.0. The resulting composites of Ag/fiber were characterized by field emission scanning electron microscopy (FESEM) and energy-dispersive X-ray spectroscopy (EDX). The results revealed that the amount of Ag agglomerates and NPs deposited on CMC fibers was higher than that deposited on cellulose fibers at similar pH conditions, and that barely any Ag agglomerates or NPs were deposited on the CA fibers. These results implied that functional groups on the cellulose backbone played two important roles in the deposition of NPs as follows: (1) Hydrogen bonding was the main driving force for agglomeration of NPs when the medium pH was below 4.4, which corresponds to the pKa of carboxylic acid groups; (2) Carboxymethyl groups could replace citrate groups as stabilizers allowing the fabrication of a uniform and evenly distributed Ag NPs layer over CMC fibers at higher pH values. This report also highlights the importance of the substrate’s surface charge and that of the pH of the medium used, on the deposition of NPs. The composite of Ag NPs on CMC electrospun fibers appears to be a promising candidate for wound dressing applications due to its superior antibacterial properties originated by the uniform and even distribution of Ag NPs on the surface of the fibers and the wound healing aptness of the CMC fibers.     

Physical immobilization of Rhizopus oryzae lipase onto cellulose substrate: activity and stability studies

Rhizopus oryzae lipase (ROL) was immobilized by adsorption onto oxidized cellulose fibers and regenerated films. The maximum adsorption level increases with the raise in the amount of carboxylic groups on cellulose surface confirming that adsorption is being governed mainly by electrostatic interaction between the enzyme and the substrate. This hypothesis was further confirmed by zeta-potential measurements showing a decrease in the zeta-potential of the fibers after enzyme adsorption. XPS analysis showed an intensification of the N 1s peak attesting the presence of the enzyme on the surface. The effect of temperature, pH and solvent polarity on the immobilized enzyme activity and stability was investigated. The catalytic esterification of oleic acid with n-butanol has been carried on using hexane as an organic solvent. A high conversion yield was obtained (about 80%) at 37 degrees C with a molar ratio of oleic acid to butanol 1:1 and 150IU immobilized lipase. The adsorption achieved two successive cycles with the same efficiency, and started to lose its activity during the third cycle.     

Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

Antibacterial modification of cellulose fibers by grafting β-cyclodextrin and inclusion with ciprofloxacin

Antibacterial-modified cellulose fiber was prepared by covalently bonding β-cyclodextrin (β-CD) with cellulose fiber via citric acid (CA) as crosslinking agent, followed by the inclusion of ciprofloxacin hydrochloride (CipHCl) as antibiotic. Effects of reaction time, temperature, concentration of β-cyclodextrin citrate (CA-β-CD) and pH on the grafting reaction were investigated, and the grafting ratio of β-CD onto cellulose fibers was 9.7 % at optimal conditions; the loading and releasing behaviors of CipHCl into/from β-CD grafted cellulose fibers were also revealed, the load amount of CipHCl into grafted cellulose fibers increased remarkably, and the release of CipHCl from the grafted cellulose fibers was prolonged. The microstructure, phase and thermal stability of modified cellulose fibers were characterized by FT-IR, ¹³C CPMAS NMR, X-ray diffraction and TGA. Considerably longer bacterial activity against E. coli and S. aureus was observed for grafted fibers loading CipHCl compared to virgin ones. Optical and mechanical properties of the paper sheets decreased generally with more antibacterial-modified fibers added.     

Physico-chemical and anatomical characterization of residual lignocellulosic fibers

Anatomical and physico-chemical properties of residual natural fibers (sugarcane bagasse, coconut fibers and peanut hulls) were characterized in order to evaluate their potential for use in the production of particleboard. The bulk density was determined by helium pycnometer and the chemical characteristics by using an electronic pH meter (for pH determination) on fibers dissolved in acidic and neutral detergents (to determine the levels of cellulose, hemicellulose and lignin). The anatomical characteristics were established using scanning electron microscopy coupled with an X-ray detector system, as well as energy dispersive X-ray spectroscopy. Results indicated similarities and differences between physico-chemical and anatomical characteristics of the residual lignocellulosic fibers when compared with the Pinus sp. wood commercially employed in particleboard production. Bulk density and pH for residual lignocellulosic fibers and Pinus sp. wood presented analogous values. Similar amounts of cellulose and lignin were identified between waste fibers and Pinus sp. wood. The presence of silica was identified in coconut fiber, peanut hull and sugarcane bagasse waste fibers, and may affect the mechanical characteristics of panels. Coconut and sugarcane bagasse fibers show surface pores with diameters ranging from 1.2 to 2.1 μm, below the 5 μm identified for Pinus sp. wood. Both fibers present pores distributed over their entire surface, whereas peanut hull fibers have no pores on their surface. This characteristic contributes to resin dispersion among particles, reflecting positively on the physical–mechanical properties of the panels. Particleboards produced with residual lignocellulosic fibers present similar physical–mechanical properties to those of Pinus sp. wood panels.     

Sorption of iron(III)–alginate complexes on cellulose fibres

Multivalent ions take a significant role in the sorption of soluble polysaccharides on solid cellulose substrates and thus demonstrate an important principle in structural polysaccharide organisation. Sorption of Fe(III)–alginate complexes on lyocell fibres as model for the insoluble cellulose matrix has been studied between pH 3–13, at 30 and 60 °C. Sorption maximum of the Fe(III)–alginate complex was observed at pH 3 where the sorbed amounts of alginate and iron were 6,600 and 85 mg iron per kg cellulose respectively. Under the experimental conditions used, a concentration of 0.05 mM Fe(III) is sufficient to achieve surface sorption of Fe(III)–alginate complex. The alginate sorption exhibited minor dependence on molar ratio of Fe(III) to alginate. In environmental scanning electron microscopy no deposition of Fe-hydroxides on the fiber surface was detected. The thickness of the adsorbed Fe(III)–alginate layer on the fiber surface was estimated with 12–22 nm. Tensile strength and abrasion resistance of Fe(III)–alginate treated fibers were not reduced through the sorption treatment. Alginate modified cellulose is of interest as material for medical application, as sorbent and textile finish.     

Reversible hydrophobization and lipophobization of cellulose fibers via trifluoroacetylation

The surface modification of cellulose fibers with trifluoroacetic anhydride (TFAA) was studied using the heterogeneous cellulose/TFAA/pyridine/toluene system. The degree of substitution (DS) of the ensuing trifluoroacetylated fibers ranged from 0.04 to 0.30. This treatment conferred a high degree of both hydrophobicity and lipophobicity on the fibers' surface, even at low DS values. Both the dispersive and the polar contributions to the surface energy were drastically reduced. However, the original cellulose hydrophilicity could be readily restored through hydrolysis, by treating the modified fibers with neutral water.     

Preparation of cellulose nanofibers with hydrophobic surface characteristics

The aim of this study was to develop cellulose nanofibers with hydrophobic surface characteristics using chemical modification. Kenaf fibers were modified using acetic anhydride and cellulose nanofibers were isolated from the acetylated kenaf using mechanical isolation methods. Fourier transform infrared spectroscopy (FTIR) indicated acetylation of the hydroxyl groups of cellulose. The study of the dispersion demonstrated that acetylated cellulose nanofibers formed stable, well-dispersed suspensions in both acetone and ethanol. The contact angle measurements showed that the surface characteristics of nanofibers were changed from hydrophilic to more hydrophobic when acetylated. The microscopy study showed that the acetylation caused a swelling of the kenaf fiber cell wall and that the diameters of isolated nanofibers were between 5 and 50 nm. X-ray analysis showed that the acetylation process reduced the crystallinity of the fibers, whereas mechanical isolation increased it. The method used provides a novel processing route for producing cellulose nanofibers with hydrophobic surfaces.     

Surface modification of cellulose fibers with layer-by-layer self-assembly of lignosulfonate and polyelectrolyte: effects on fibers wetting properties and paper strength

To convert the hydrophilic cellulose fiber into hydrophobic, multilayers composed of cationic polyacrylamide (CPAM) and lignosulfonate (LS) were constructed on cellulose fiber surface using layer-by-layer (LBL) self-assembly technique. The presence of CPAM/LS multilayers were validated by zeta potential, X-ray photoelectron spectroscopy and atomic force microscopy (AFM). It was found that potential of fiber surface inversed after deposition of each layer, the contents of characteristic elements (i.e. S and N) of CPAM/LS multilayers increased with increasing bilayer number, furthermore, the calculated surface LS content increased linearly as a function of bilayers. AFM phase images indicated that the cellulose microfibrils on fiber surface were gradually covered by LS granules, resulting in an increase in fiber surface roughness as self-assembly proceeded. The wetting properties of modified cellulose fibers were detected by dynamic contact angle measurement. The results showed that the initial water contact angle gradually increased and the attenuation rate of the contact angle gradually decreased with the number of bilayers, suggesting that the controllable hydrophobicity of cellulose fiber can be achieved depending on the number of bilayers. It also showed that the polyelectrolyte presented in the outermost layer significantly influenced the wetting properties of cellulose fibers, and a higher hydrophobicity was observed when LS was in the outermost layer. Moreover, tensile strength test was performed on the handsheet prepared from LBL modified fibers to evaluate the effect of CPAM/LS multilayers on strength property of cellulose fiber networks. The tensile index of handsheet prepared from fibers modified with a (CPAM/LS)₅ multilayer increased by 12.4% compared with that of handsheet prepared from original fibers. The print density of handsheet increased with the number of bilayers, suggesting that printability of the handsheet was improved by constructing CPAM/LS multilayers on cellulose fiber surface. This strategy will have a positive impact and potential application value in printing process control of cellulose fiber-based products.     

Surface methacrylation and graft copolymerization of ultrafine cellulose fibers

Ultrafine fibrous (? from 100 to 450 nm) cellulose membranes were generated by electrospinning of cellulose acetate [degree of substitution (DS): 2.45, weight‐average molecular weight: 30,000 Da], followed by alkaline deacetylation. Reaction of these ultrahigh surface‐area cellulose fibers with methacrylate chloride (MACl) produced activated surfaces without altering the fiber morphology. Surface methacrylation of these fibers was confirmed by the acquired hydrophobicity (θ_water = 84°) as compared to the originally hydrophilic (θ_water = 56°) cellulose. Changing the MACl:OH molar ratios could vary the overall DS of methacrylation. The very low overall DS values indicate the surface nature of the methacrylation reaction. At a DS of 0.17, the thermal properties of the surface methacrylated cellulose resemble those of cellulose derivatives at much higher DS values, an unusual behavior of the ultrafine fibers. The methacrylated cellulose could be further copolymerized with vinyl monomers (methyl methacrylate, acrylamide, and N‐isopropylacrylamide) as linear grafts or three‐dimensional (3D) networks. The morphology of cellulose fibers and the interfiber pore structure were not altered at 15–33% graft levels. This study demonstrates that either linear or 3D networks of vinyl polymers could be efficiently supported on ultrafine cellulose fibrous membranes via surface methacrylation. Through these surface reactions the chemical, thermal, and liquid wetting and absorbent properties of these ultrafine fibrous membranes were significantly altered with no change to the fiber dimensions or interfiber pore morphology. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 953–964, 2003     

Morphology control of poly(lactic) acid/polypropylene blend composite by using silanized cellulose fibers extracted from coir fibers

The objective of this work is the use of cellulose fibers extracted from coir fibers as Janus nanocylinders to suppress the phase retraction and coalescence in poly(lactic) acid/polypropylene bio-blend polymers via prompting the selective localization of cellulose fibers at the interface using chemical modification. The untreated and modified cellulose fibers extracted from coir fibers using a silane molecule (tetraethoxysilane) were used as reinforcement and as Janus nanocylinder at two weight contents (2.5 wt% and 5 wt%) to manipulate the morphology of the bio-blends. Their bio-composites with PLA-PP matrix were prepared via melt compounding (at PLA/PP: 50/50). The treatment effect on component interaction and the bio-composites properties have been studied via Scanning electron microscopy, infrared spectroscopy, and differential calorimetry analysis. The mechanical and rheological properties of nanocomposites were similarly assessed. Young's modulus and tensile strength of PLA-PP nanocomposites reinforced by silanized cellulose fibers show a great enhancement as compared to a neat matrix. In particular, there was a gain of 18.5% in Young's modulus and 11.21% in tensile strength for silanized cellulose fiber-based bio-blend composites at 5 wt%. From the rheological point of view, it was found that the silanized cellulose fibers in PLA-PP at both fibers loading enhances the adhesion between both polymers leading to tuning their morphology from sea-island to the continuous structures with the appearance of PLA microfibrillar inside of bio-composites. This change was reflected in the relaxation of the chain mobility of the bio-blend composites.

     

Synthesis and characterization of cellulose fibers grafted with hyperbranched poly(3-methyl-3-oxetanemethanol)

Hyperbranched poly(3-methyl-3-oxetanemethanol) (HBPO) was directly grafted from the surface of cellulose fibers (CF) through a surface hydroxyl group-initiated ring-opening polymerization of 3-methyl-3-oxetanemethanol (MOM). TOF–SIMS, XPS, AFM, ATR-FTIR, and TGA were utilized for characterizing the resultant HBPO-grafted cellulose fibers. The content of grafted HBPO is easily adjustable by controlling feeding dosage of the MOM. To verify the reactivity of hydroxyl groups in the grafted HBPO, poly(ε-caprolactone) (PCL) was further grafted from the HBPO-grafted cellulose surface.     

Self-aggregation of cationic surfactants onto oxidized cellulose fibers and coadsorption of organic compounds

In this work, the adsorption of cationic surfactant and organic solutes on oxidized cellulose fibers bearing different amounts of carboxylic moieties was investigated. The increase in the amount of -COOH groups on cellulose fibers by TEMPO oxidation induced a general rise in surfactant adsorption. For all tested conditions, that is, cellulose oxidation level and surfactant alkyl chain length (C12 and C16), adsorption isotherms displayed a typical three-region shape with inversion of the substrate zeta-potential which was interpreted as reflecting surfactant adsorption and aggregation (admicelles and hemimicelles) on cellulose fibers. The addition of organic solutes in surfactant/cellulose systems induced a decrease in surfactant cac on the cellulose surface thus favoring surfactant aggregation and the formation of mixed surfactant/solute assemblies. Adsorption isotherms of organic solutes on cellulose in surfactant/cellulose/solute systems showed that solute adsorption is strictly correlated to (i) the surfactant concentration, solute adsorption increases up to the surfactant cmc, where solute partitioning between the cellulose surface and free micelles causes a drop in adsorption, and to (ii) solute solubility and functional groups. The specific shape of solutes adsorption isotherms at a fixed surfactant concentration was interpreted using a Frumkin adsorption isotherm, thus suggesting that solute uptake on cellulose fibers is a coadsorption and not a partitioning process. Results presented in this study were compared with those obtained in a previous work investigating solute adsorption in anionic surfactant/cationized cellulose systems to better understand the role of surfactant/solute interactions in the coadsorption process.     

On the indirect polyelectrolyte titration of cellulosic fibers. Conditions for charge stoichiometry and comparison with ESCA

The effect of electrolyte (NaHCO3) concentration on the adsorption of poly-DADMAC (poly-diallyldimethylammonium chloride) onto cellulosic fibers with different charge profiles was investigated. Surface carboxymethylated fibers were obtained by grafting carboxymethyl cellulose (CMC) onto the fiber surface and bulk carboxymethylated fibers were obtained by reacting the fibers with monochloroacetic acid. It was shown that nonionic interactions do not exist between cellulose and poly-DADMAC, rather electrostatic interactions govern the adsorption. Charge stoichiometry prevails under electrolyte-free conditions, whereas surface charge overcompensation occurs at higher electrolyte concentrations. It was shown that charge stoichiometry prevails if the thickness of the electric double layer kappa(-1) was larger than the mean distance between the charges on the fiber surface, as predicted by polyelectrolyte adsorption theories, taking lateral correlation effects into account. In a second set of experiments the ESCA technique served to independently calibrate the polyelectrolyte titrations for determining the surface charge of cellulosic fibers. Various molecular masses of poly-DADMAC were adsorbed to carboxymethylated fibers having different charge profiles. The adsorption of low M(w) poly-DADMAC (7.0 x 10(3)), analyzed by polyelectrolyte titration, was about 10 times higher than that of the high M(w) poly-DADMAC (9.2 x 10(5)). Despite the difference in accessibility of these two polyelectrolytes to the fiber cell wall, ESCA surface analysis showed, as expected, only slight differences between the two polyelectrolytes. This gives strong credibility to the idea that surface charge content of cellulosic fibers can be analyzed by means of adsorption of a high-molecular-mass cationic polymer, i.e., by polyelectrolyte titration.     

Synthesis of cellulose–metal nanoparticle composites: development and comparison of different protocols

Deposition of nanoparticles on the surface of a variety of materials is a subject of great interest due to their potential applications in electronic devices, sensing, catalysis and bio-medical sciences. In this context, we have explored and compared various methodologies to generate gold and silver nanoparticles on the surface of cellulose fibers. It was found that boiling of the cellulose fibers in alkaline solution of gold and silver salts led to the formation and immobilization of gold and silver nanoparticles. However, in case of lecithin treated and thiol-modified cellulose fibers, high temperature was not essentially required for the formation and deposition of nanoparticles on cellulose substrate. In both these cases, fairly uniform metal nanoparticles were obtained in good yields (~43 wt% gold loading in case of thiol modified cellulose fibers) at room temperature. Borohydride-reduction method resulted in relatively lower loading (~22 wt%) with a wide size distribution of gold and silver nanoparticles on cellulose fibers. All these nanoparticle–cellulose composites were thoroughly characterized using scanning electron microscopy, energy dispersive X-ray, Fourier transform infrared spectroscopy, UV–visible spectroscopy, and elemental analyzer. Thiol modified cellulose–gold nanoparticle composites served as active catalysts in the reduction of 4-nitrophenol into 4-aminophenol.     

The fiber charge measurement depending on the poly-DADMAC accessibility to cellulose fibers

Cellulose fiber charge is a significant parameter for porous cellulose fibers, and strongly affects the swelling ability of cellulose fibers and the properties of cellulose-based materials as well. Actually, it includes surface charge and inner charge. The surface charge is mentioned often in papermaking wet-end chemistry, however, the inner charge or the total charge is paid less attention to. In this study, the cationic polydiallyldimethyl ammonium chloride (poly-DADMAC) with different molecular weight (Mw) was applied for the accessibility evaluation to the cellulose fiber charges by using polyelectrolyte adsorption technique. Results showed that higher fiber charge was detected by lower Mw poly-DADMAC (7.5–15 kDa) due to its highly efficient penetration into the fiber cell walls and neutralization with inner charges, while lower fiber charge was obtained by using higher Mw poly-DADMAC (higher than 100 kDa) because of its adsorption onto fiber surface. As a consequence, high-Mw poly-DADMAC was used to determine the surface charge of cellulose fibers, and low-Mw poly-DADMAC could be used to measure the total charge under the saturated adsorption and low ionic strength (or salts concentration). This was confirmed by SEM–EDS analysis. The low-Mw poly-DADMAC adsorption had a good agreement with conventional conductometric titration, and a linear regression equation with slope of 1.03 and regression coefficient of 0.99 was obtained.     

Properties of Monocarboxy Cellulose Containing Sorbed Fe(III), Al(III), and Cr(III) Cations

Sorption of Fe(III), Al(III), and Cr(III) on monocarboxy cellulose at various pH, concentrations of metal chloride or sulfate in solution, and time was studied. The effect of type and amount of the cation sorbed on the physicomechanical properties, swelling, and stability in phosphate buffer of monocarboxy cellulose fibers was considered.     

Controlling deposition and release of polyol-stabilized latex on boronic acid-derivatized cellulose

Poly(glycerol monomethacrylate)-stabilized polystyrene (PGMA-PS) latex particles undergo specific, pH-dependent adsorption onto regenerated cellulose film bearing surface phenylboronic acid groups (cellulose-PBA). Deposition occurs at pH 10 and is driven by the boronate ester formation with the polyol latex surface coating. In contrast, no deposition occurs at pH 4, and previously deposited particles can be readily desorbed at this lower pH. In control experiments, conventional anionic sulfate-stabilized polystyrene latex did not deposit onto the hydrophilic cellulose surface. The distribution of boronate groups in the cellulose was determined by exposure to Alizarin Red S dye, which forms a fluorescent complex with phenylboronic acid; confocal microscopy was used to determine a surface density of 3 nm(2) per boronic acid group on the cellulose surface. Although the boronic acid binding constant with PGMA is relatively low (5.4 L/mol), the cooperative interactions between multiple PBA surface sites and the many PGMA chains per latex particle are sufficient to induce specific latex adsorption, providing a convenient new tool for controlling nanoparticle deposition on surfaces.     

Surface esterification of cellulose fibers: characterization by DRIFT and contact angle measurements

The surface chemical modification of microcrystalline cellulose and cellulose fibers obtained from different sugar cane bagasse pulping processes, viz. Kraft, organosolv ethanol/water and organosolv/supercritical carbon dioxide, were studied in heterogeneous conditions using modest amounts of octadecanoyl and dodecanoyl chloride. The ensuing surfaces acquired a non-polar character, suitable for incorporating these fibers as reinforcing agents in composite materials based on polymeric matrices. The success of these chemical modifications was assessed by diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, elemental analysis, scanning electron microscopy (SEM) and contact angle measurements. In particular, the dynamic and equilibrium contact angle measurements, before and after the treatments, revealed that the value of the polar component (gamma(s)p) of the surface energy had decreased very considerably following the modification.     

In situ generated cellulose nanoparticles to enhance the hydrophobicity of paper

Handsheets with in situ generated cellulose nanoparticles were made from oxidized pulp fibers prepared by 2,2,6,6-tetramethylpiperidinyl-1-oxyl-mediated oxidation of kraft fiber with sodium hypochlorite and sodium bromide. The oxidized pulp fibers were blended prior to handsheet formation for short times (1–3 min). From gravimetric analysis of the supernatant, yield of cellulose nanoparticles generated from this blending process were up to 9.5 dry wt%. Scanning electron microscopy showed that the handsheets fabricated in a wetlay process had increased smoothness with increased blending time. A significant decrease in water vapor transmission rate for the sheets supported the hypothesis that cellulose nanoparticles fill the empty spaces between pulp fibers throughout the handsheet affording a more dense structure. Oxidation significantly enhanced the tensile index of the handsheets and this value was further improved by blending for 2 min. The handsheets were treated with a solution of octadecylamine (ODA) modifying the surface chemistry of the paper. Irreversibly adsorbed ODA on the oxidized cellulose surfaces after extensive extraction was confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Sessile drop contact angle tests for modified handsheets illustrated its enhanced hydrophobicity with contact angles over 90°. Overall the study developed a novel route to make paper with enhanced functionality without the need to separately deposit nanocellulose onto the paper surface.