Heterogeneous nucleation and growth of calcium carbonate on calcite and quartz

The precipitation of calcium carbonate as a binding salt for the consolidation of loose sand formations is a promising approach. The heterogeneous nucleation and growth of calcite were investigated in supersaturated solutions. The ionic activities in the solutions tested were selected so that they included both supersaturations in which crystal growth took place only following the introduction of seed particles and supersaturations in which precipitation occurred spontaneously past the lapse of induction times. In the latter case the supersaturation conditions were sufficiently low to allow the measurement of induction times preceding the onset of precipitation. The stability domain of the calcium carbonate system was established at pH 8.50, 25 degrees C, measuring the induction times in the range between 30 min and 2 h. The rates of precipitation following the destabilization of the solutions were measured from the pH and/or concentration-time profiles. The induction times were inversely proportional and rates proportional to the solution supersaturation as expected. The high-order dependence of the rates of precipitation on the solution supersaturation suggested a polynuclear growth mechanism. Fitting of the induction time-supersaturation data according to this model yielded a value of 64 mJ/m2 for the surface energy of the calcite nucleus. In the concentration domain corresponding to stable supersaturated solutions, seeded growth experiments at constant supersaturation showed a second-order dependence on the rates of crystal growth of calcite seed crystals. Inoculation of the stable supersaturated solutions with quartz seed crystals failed to induce nucleation. Raising supersaturation to reach the unstable domain showed interesting features: calcite seed crystals yielded crystal growth kinetics compatible with the polynuclear growth model, without any induction time. The presence of quartz seed crystals reduced the induction times and resulted in nucleation in the bulk solution. The kinetic data in the latter case were consistent with the polynuclear growth model and the surface energy for the newly forming embryo was calculated equal to 31.1 mJ/m2, because of the dominantly heterogeneous nature of the process.     

Effect of inorganic anions on the morphology and structure of magnesium calcite

Calcium carbonate was precipitated from calcium hydroxide and carbonic acid solutions at 25 degrees C, with and without addition of different magnesium (MgSO(4), Mg(NO(3))(2) and MgCl(2)) and sodium salts (Na(2)SO(4), NaNO(3) and NaCl) of identical anions, in order to study the mode of incorporation of magnesium and inorganic anions and their effect on the morphology of calcite crystals over a range of initial reactant concentrations and limited c(i)(Mg(2+))/c(i)(Ca(2+)) molar ratios. The morphology, crystal size distribution, composition, structure, and specific surface area of the precipitated crystals, as well as the mode of cation and anion incorporation into the calcite crystal lattice, were studied by a combination of optical and scanning electron microscopy (SEM), electronic counting, a multiple BET method, thermogravimetry, FT-IR spectroscopy, X-ray diffraction (XRD), and electron paramagnetic resonance (EPR) spectroscopy. In the systems of high initial relative supersaturation, precipitation of an amorphous precursor phase preceded the formation of calcite, whereas in those of lower supersaturation calcite was the first and only polymorphic modification of calcium carbonate that appeared in the system. The magnesium content in calcite increased with the magnesium concentration in solution and was correlated with the type of magnesium salt used. Mg incorporation caused the formation of crystals elongated along the calcite c axis and, in some cases, the appearance of new [011] faces. Polycrystalline aggregates were formed when the c(i)(Mg(2+))/c(i)(Ca(2+)) molar ratios in solution were increased. Addition of sulfate ions, alone, caused formation of spherical calcite polycrystalline aggregates.     

Removal of copper (Cu2+) from water by sulfonated cellulose

Water insoluble sulfonated cellulose was prepared and applied for Cu²⁺ removal from water. The effects of sorbent dose, initial solution pH, temperature and initial Cu²⁺ concentration on the removal performance of sulfonated cellulose were investigated. Isothermal data were modeled with the Langmuir and Freundlich isotherm models. The Cu²⁺ sorption onto sulfonated cellulose followed the Langmuir isotherm model with the maximum sorption capacity of 8.2?mg-Cu²⁺/g. Removal of Cu²⁺ showed rapid initial kinetics; in 3?min removal of Cu²⁺ reached equilibrium status. Thermodynamic study revealed an exothermic sorption process. In addition, sulfonated cellulose is a kind of green and renewable sorbent because it can be easily regenerated by 0.1?M HCl.     

Atomic force microscopy investigation of the mechanism of calcite microcrystal growth under Kitano conditions

A combined atomic force microscopy (AFM)-inverted optical microscopy technique has been used to image the surface of calcite single microcrystals, with dimensions of 10-20 microm, at high resolution. The microcrystals were grown on a glass substrate using the Kitano method, a process that involves the outgassing of carbon dioxide from a saturated solution of calcium carbonate. The resulting increase in the supersaturation of the solution, with respect to calcium carbonate, induces crystallization. It is demonstrated, for the first time, that calcite microcrystals formed in this way exhibit a single spiral growth hillock on the (104) surface, as evidenced by a spiral step pattern, indicating that growth occurs at steps arising from an individual screw dislocation. The subsequent reactivity of these crystals under Kitano conditions has been followed in situ using AFM imaging.     

Model cellulose films exposed to H. insolens glucoside hydrolase family 45 endo-cellulase--the effect of the carbohydrate-binding module

The effects of enzyme structure and activity on the degradation of model cellulose substrates were investigated by ellipsometry for the cellulase Humicola insolens GH45. The inactive variant D10N was found to adsorb at the cellulose surface but also to be incorporated into the cellulose films to an extent that depended on pH. For the native protein, the initial adsorption monitored for the inactive variant D10N was followed by enzyme-mediated degradation of the cellulose films. Again, a dependence on pH was found, such that higher pH resulted in slower enzymatic degradation. Removing the carbohydrate-binding module eliminated this pH dependence but also resulted in a decreased adsorption to the cellulose surface, and in a decreased net catalytic effect.     

Atomistic nature of NaCl nucleation at the solid-liquid interface

The early stage of heterogeneous nucleation of NaCl from supersaturated NaCl aqueous solution at the water-NaCl (001) interface has been investigated by molecular dynamics simulations. The critical size of the nuclei for spontaneous growth was found to be as small as two atoms (a Na(+)-Cl(-) ion pair) at high supersaturation. Due to the presence of a relatively stable water network and the effect of the hydration force at the interface, the stable nuclei formed on the NaCl (001) are found to contain more Na(+) ions than Cl(-) ions. The different deposition characteristics of the Na(+) and Cl(-) solutes lead to a positively charged substrate and thus may introduce another driving force for nucleation besides the level of solution supersaturation. The role of water was further confirmed by comparison with NaCl epitaxy growth in the vacuum.     

Crystallization kinetics of calcium carbonate at a stoichiometric ratio of components

The formal kinetics of calcium carbonate crystallization in aqueous solutions is studied at a stoichiometric ratio of Ca²⁺ and CO₃^2- ions. The kinetics of the process was monitored by convenient and reliable methods (complexometric analysis for calcium in an aqueous solution and energy dispersive and microscopic measurement of solid particle sizes). The effect the temperature and degree of supersaturation have on the periods of induction and mass crystallization and the equilibrium concentration of calcium ions in solution is estimated at continuously controlled pH and solution ionic strength. The kinetic parameters (n, k, τ_1/2, E_a) of calcium carbonate crystallization are calculated. It is shown that calcium carbonate with a calcite structure formed at a stoichiometric ratio of reagents, and changes in the temperature (25–45°C) and the solution’s degree of supersaturation (2–6) within the considered range had no effect on the characteristics of the solid phase.     

Divalent Cd and Pb uptake on calcite {1014} cleavage faces: an XPS and AFM study

The interaction of divalent Cd and Pb with the {101 4} cleavage faces of calcite has been investigated with X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Analysis of the {101 4} cleavage planes of calcite was carried out with X-ray photoelectron spectroscopy (XPS) after exposure to divalent metal-bearing solutions in the 0.1-100 microM concentration range for times ranging from 1 to 24 h. The uptake of Cd2+ by calcite was determined to be greater than that of Pb2+ under similar experimental conditions (1 microM, pH 8.2, 24 h exposure time). In both cases, the majority of the divalent metal was postulated to exist in a surface precipitate. AFM results showed that the exposure of calcite to a 1 microM Pb2+ solution resulted in ellipsoidal surface growths that were attributed to the nucleation of a PbCO3 bulk phase. In the Cd circumstance, AFM showed comparatively flat growth features forming on the calcite surface even at concentrations down to 0.1 microM, where the solution would be expected to be undersaturated with respect to Cd bulk phases. These features were attributed to a (Ca,Cd)CO3 solid solution. The individual exposure of these Cd/CaCO3 and Pb/CaCO3 samples to water pre-equilibrated with calcite (metal free) for 1 h led to the removal of no more than 20% of the divalent metal, suggesting that if there was an adsorbed Pb or Cd complex initially on the calcite surface, it was an minority species compared to the precipitate phase. Exposure of calcite to 100 microM Cd and Pb resulted in the accumulation of precipitate on the calcite surface presumably due to the divalent metal initial solution concentrations exceeding the solubility products of CdCO3 and PbCO3, respectively.     

Fluorescence and light-scattering studies on the formation of stable colloidal nanoparticles made of sodium sulfonated polystyrene ionomers

The lightly sulfonated polystyrene ionomer is only soluble in some organic solvents, such as toluene and tetrahydrofurnan (THF). The mixture of its organic solution with water normally leads to macroscopic phase separation, namely precipitation. In this study, using the steady-state fluorescence, the nonradiative energy transfer and dynamic laser light scattering, we demonstrate that the sulfonated polystyrene ionomers can form stable colloidal nanoparticles if the THF solution of the ionomers is dropwisely added into an excessive amount of water, or vice verse, water is added in a dropwise fashion into the dilute ionomer THF solution under ultrasonification or fast stirring. The hydrophobic core made of the polystyrene backbone chains is stabilized by the ionic groups on the particle surface. Such formed stable nanoparticles have a relatively narrow size distribution with an average diameter in the range of 5–12 nm, depending on the degree of sulfonation, the initial concentration of the ionomer THF solution, and the mixing order. This study shows another way to prepare surfactant-free polystyrene nanoparticles. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1593–1599, 1997     

Early homogenous amorphous precursor stages of calcium carbonate and subsequent crystal growth in levitated droplets

An in situ study of the contact-free crystallization of calcium carbonate in acoustic levitated droplets is reported. The levitated droplet technique allows an in situ monitoring of the crystallization while avoiding any foreign phase boundaries that may influence the precipitation process by heterogeneous nucleation. The diffusion-controlled precipitation of CaCO3 at neutral pH starts in the initial step with the homogeneous formation of a stable, nanosized liquid-like amorphous calcium carbonate phase that undergoes in a subsequent step a solution-assisted transformation to calcite. Cryogenic scanning electron microscopy studies indicate that precipitation is not induced at the solution/air interface. Our findings demonstrate that a liquid-liquid phase separation occurs at the outset of the precipitation under diffusion-controlled conditions (typical for biomineral formation) with a slow increase of the supersaturation at neutral pH.     

Bioinspired crystallization of CaCO3 coatings on electrospun cellulose acetate fiber scaffolds and corresponding CaCO3 microtube networks

This article describes the mineralization behavior of CaCO(3) crystals on electrospun cellulose acetate (CA) fibers by using poly(acrylic acid) (PAA) as a crystal growth modifier and further templating synthesis of CaCO(3) microtubes. Calcite film coatings composed of nanoneedles can form on the surfaces of CA fibers while maintaining the fibrous and macroporous structures if the concentration of PAA is in a suitable range. In the presence of a suitable concentration of PAA, the acidic PAA molecules will first adsorb onto the surface of CA fibers by the interaction between the OH moieties of CA and the carboxylic groups of PAA, and then the redundant carboxylic groups of PAA can ionically bind Ca(2+) ions on the surfaces of CA fibers, resulting in the local supersaturation of Ca(2+) ions on and near the fiber surface, which can induce the nucleation of CaCO(3) on the CA fibers instead of in bulk solution. Calcite microtube networks on the macroscale can be prepared by the removal of CA fibers after the CA@CaCO(3) composite is treated with acetone. When the CA fiber scaffold is immersed in CaCl(2) solution with an extended incubation time, the first deposited calcite coatings can act as secondary substrate, leading to the formation of smaller calcite mesocrystal fibers. The present work proves that inorganic crystal growth can occur even at an organic interface without the need for commensurability between the lattices of the organic and inorganic counterparts.     

The interaction of diphosphonates with calcitic surfaces: understanding the inhibition activity in marble dissolution

The rates of dissolution of calcitic Carrara marble have been reported to be significantly reduced in alkaline pH (pH 8.25) at 25 degrees C in the presence of (1-hydroxyethylidene)-1,1 diphosphonic acid (HEDP). The adsorption takes place at the calcite/water interface at the double layer through the interaction of charged surface species with the charged solution species of the adsorbate. The present work focused on obtaining a better understanding of the interaction of the calcite surface with HEDP. Calculations were performed according to the triple layer model, assuming the formation of surface complexes between the charged surface species of calcite and the species of HEDP dominant at pH 8.25. According to the model, the adsorbed species are located at the inner Helmholtz plane of the electrical double layer. Strong lateral interactions between the adsorbed species were suggested and were corroborated from the calculation of the respective energy, which was equal to 69 kJ mol(-1). The adsorption isotherm was consistent with the proposed model at low surface coverage values, while discrepancies between the values experimentally measured and the predicted were found at higher adsorbate concentrations. The deviations from the predicted values were attributed to the fact that HEDP adsorption on calcite resulted in the formation of multiple layers. The model explained adequately the changes in the zeta-potential values of calcite in the presence of HEDP in the solution which resulted in charge reversal upon adsorption.     

Transport phenomena of sulfonated dyes into cellulose membrane: Effects of urea on parallel diffusion of mono azo dyes

 Effects of urea on transport phenomena of sulfonated azo dyes with different aggregation constants into water-swollen cellulose membrane have been studied at 25–55 °C. The results were analyzed on the basis of a parallel transport theory of surface and pore diffusion. Addition of urea decreased equilibrium adsorption of the dyes onto cellulose and increased the surface and pore diffusivities for the parallel diffusion model of the dye with high aggreg-ation constant. Temperature dependence of the effects was also discussed. Received: 30 November 1996 Accepted: 7 April 1997     

Dynamic Membranes Based on Poly(N-Isopropylacrylamide-co-Heptadecyl Vinyl Ketone): Preparation and Properties

Dynamic membranes were prepared from poly(N-isopropylacrylamide-co-heptadecyl vinyl ketone) having a lower critical solution temperature in an aqueous solution and being a micelle-forming surfactant. The dependence of the critical concentration of the copolymer micellization on temperature was shown to have an extreme character, with a minimum at the lower critical solution temperature of the copolymer. The dynamic membranes are formed on both the hydrophilic (cellulose) and hydrophobic (polyacrylonitrile) supports. For the penetrants studied, it was found that the dynamic membrane formed on the hydrophobic support favors the rejection of a PEG₆₀₀₀, while that formed on the hydrophilic support rejects more effectively albumin and sodium cellulose sulfoacetate. We failed to realize a completely reversible thermal control of transport properties of the dynamic membranes obtained, while it was readily accomplished for the membranes obtained by grafting N-isopropylamide onto a cellulose matrix.     

Model films of cellulose ID – improved preparation method and characterization of the cellulose film

An optimization study of the preparation of spin-coated cellulose model films from the NMMO/DMSO system on silicon wafers has been made. The study shows that the cellulose concentration ID the solution determines the cellulose film thickness and that the temperature of the solution affects the surface roughness. A lower solution temperature results ID a lower surface roughness at cellulose concentrations below 0.8%. Using the described method, ID ID possible to prepare films with thicknesses of 30–90 nm with a constant surface roughness by changing the cellulose concentration, i.e. by dilution with DMSO. On these films, water has a contact angle less than 20° and about 50% of the material can, according to CP/MAS ¹³C-NMR spectroscopy on corresponding fibrous material, be considered to consist of crystalline cellulose ID type material. ID has further been shown that AFM can be used to determine the thickness of cellulose films, ID both dry and wet states. ID this method, the difference ID height between the top surface and the underlying wafer has been measured at an incision made into the cellulose film. The cellulose films have also been spin-coated with the same technique as on the silicon oxide wafer onto the crystal ID a quartz crystal microbalance (QCM). These model films were found to be suitable for swelling measurements with the QCM. The films were very stable during this type of measurement and films with different amounts of charges gave different swelling responses depending on their charges. As expected, films with a higher charge showed a higher swelling.     

Formation of stable vaterite with poly(acrylic acid) by the delayed addition method

The crystallization of CaCO3 was examined by changing the addition time of poly(acrylic acid) (PAA) to an aqueous solution of calcium carbonate by selectively interacting with the crystal at different stages during the crystal-forming process. The precipitation of CaCO3 was carried out by a double jet method to prevent heterogeneous nucleation on glass walls, and the sodium salt of PAA was added by a delayed addition method. In the initial presence of PAA in an aqueous solution of calcium carbonate, PAA acted as an inhibitor for the nucleation and growth of crystallization. However, it was found that stable vaterite particles were successfully obtained by delaying the addition of PAA from 1 to 60 min. The vaterite particles were stable in the aqueous solution for more than 30 days, and the CaCO3 particles were formed by a spherulitic growth mechanism. It is suggested that PAA strongly binds with the Ca2+ ion on the surface of CaCO3 particles to stabilize the unstable vaterite form effectively. Upon changing the addition time of PAA, we found that CaCO3 particles were formed through different formation mechanisms in selectively controlled crystallization at different stages during the crystallization process.     

Transformation of vaterite into calcite in the absence and the presence of copper(II) species

The transformation of vaterite into calcite may be performed by heating in the presence and the absence of oxygen. Vaterite remains thermally stable until a calcination temperature of 450°C. It transforms progressively to calcite up to 500°C giving two exothermic peaks: 1) at 481°C due to the transformation of vaterite surface which is in contact with a small amount of calcite phase already formed with the time on the solid surface from the humidity atmosphere; 2) at 491°C due to the transformation of pure vaterite bulk. The calcite phase remains stable until 700°C. Above this temperature the formation of CaO is observed. This revised version was published online in August 2006 with corrections to the Cover Date.     

Experimental and computational growth morphology of two polymorphs of a yellow isoxazolone dye

We report on the crystal structures and the experimentally found and the computationally predicted growth morphologies of two polymorphs of a yellow isoxazolone dye. The stable polymorph I has a blocklike habit, and the metastable polymorph II grows as fine needles, nucleating only by heterogeneous or contact nucleation. The habits of both polymorphs depend on the supersaturation during growth. The experimental observations are compared with predictions of the attachment energy model and kinetic Monte Carlo lattice simulations in which the growth is modeled as an "atomistic process", governed by surface energetics. These Monte Carlo simulations correctly predict the shape and the dependence on supersaturation of the crystal morphology for both polymorphs: for polymorph I, a strong dependence on supersaturation is found from the simulations. For polymorph II, the order of morphological importance is reproduced correctly, as well as the needlelike morphology.     

Rheology of water-in-water suspensions formed with lightly sulfonated ionomers

The formation and rheological properties of water-in-water suspensions formed by mixing a dilute nonaqueous solution containing a lightly sulfonated ionomer with an aqueous solution are described. The spheres formed via this process are composed of a very thin (approximately 2000 Å), ionically crosslinked gel membrane which separates the continuous aqueous phase from the encapsulated aqueous phase. The membrane itself is composed of the lightly sulfonated ionomer (i. e., sulfonated polystyrene) swollen with the nonaqueous solvent. Interestingly, surface tension measurements indicate that the sulfonated ionomer in this nonaqueous solvent has no significant interfacial activity. Viscometric measurements confirm that aqueous solvents containing these spheres have considerably enhanced viscosity even in the presence of high concentrations of a salt or acid. Thixotropic behavior is observed at low shear rates, whereas Newtonian behavior is observed at higher rates of shear (> 40 sec^–1). Cessation of stress reverts the viscosity to its initial value. Dilution studies show that the streamlines in the flowing exterior aqueous phase cause circulation of the aqueous fluid within the sphere. These results point to the fluid-like characteristics of the gel membrane, since transmission of the stress across the membrane is not dramatically inhibited. Comparison of the low shear rate data with the Mooney equation support these conclusion.     

酸碱处理后纳米微晶纤维素的热行为分析

Nanocrystalline cellulose (NCC) was prepared from microcrystalline cellulose (MCC) by acid hydrolysis. It was observed that the diameter of NCC particles mainly distributed over 30-50nm by transmission electron microscope (TEM) . The crystal form and degree of crystallinity were detected by X-Ray diffraction. The results showed that NCC and MCC have the same crystal form of cellulose I, and that the reactions mainly occurred in the amorphous region of MCC during the acid hydrolysis process. The thermal behavior of NCC in different pH conditions was characterized by differential scanning calorimetry (DSC) . The consequences indicate that the thermal stability of NCC distinctly decreased by contrast with the thermal stability of MCC, and that the thermal stability of NCCs in alkali conditions was higher than that of NCCs in acid conditions. The specific surface area distinctly increased with sharp decreasing of the particle size of NCC. This induced the end carbons and active groups of surface of NCC to increase sharply, therefore caused the thermal stability of NCC to distinctly abate. That NCC has very strong adsorption affinity is the cause of the obvious difference of thermal behavior of NCC in different pH. In acid conditions the surface of NCC adsorbed a great lot of H^ , which induced the cellulose chains of surface of NCC to decompose at low temperature catalyzed by H^ . When adding sodium hydroxide solution, on one hand the H^ of surface of NCC was neutralized; on the other hand, the cellulose chains of low molecular weight were dissolved in sodium hydroxide solution and the defects of surface of NCC rearranged and stable structure formed. These factors improved the thermal stability of NCC in alkali conditions.