普鲁士蓝膜修饰极循环伏安行为的研究

本文研究普鲁士蓝（PB）膜修饰电极的循环伏安行为，结果表明，膜中电活性中心间的相经作用导致PB膜电极的伏安行为偏离理想表面波，用有限扩散边模型解释了高电位扫速下膜电极的伏安行为，在含钾离子的电解质溶液中测得PB膜中电荷传输扩散系数为10^-9-10^-11cm^2/s。     

分步电沉积普鲁士蓝、纳米铜复合膜修饰玻碳电极测定芦丁

采用分步电沉积方法,依次将普鲁士蓝膜(PB)和纳米铜(CuNPs)电沉积在玻碳电极(GCE)表面,制备了相应的修饰电极(CuNPs/PB/GCE)。考察了实验条件,并采用循环伏安(CV)法和差分脉冲伏安(DPV)法研究了芦丁在CuNPs/PB/GCE上的电化学行为,求解了相关的电化学参数。最佳条件下,采用DPV法,芦丁的还原峰电流与其浓度在1.0×10-8~1.0×10-4 mol/L范围内呈现良好的线性关系,其检出限(S/N=3)为2.8×10-9 mol/L。结果表明,电极表面PB和CuNPs的存在有效提高了芦丁的电化学响应。该修饰电极的选择性和重现性好,可以应用于水样中芦丁的检测。     

电沉积普鲁士蓝/壳聚糖修饰金电极的电化学研究

应用控制电位电解法在金电极上进行了普鲁士蓝(PB)/壳聚糖(CS)修饰膜的电沉积。在pH2、溶液组成为2.5 mmol/L FeCl3 2.5 mmol/L K3[Fe(CN)6] 0.01%CS 0.01 mol/L HCl和0.1 mol/L KCl的溶液中,于0.4 V(vs.SCE)电沉积300 s,获得性能理想的沉积膜。对修饰膜进行了红外和显微表征,结果表明,PB和CS同时沉积在电极上,且膜结构较纯PB沉积膜粗糙,修饰量大,具有更强的空间结构性。研究了PB/CS/金修饰电极(PB/CS/Au/CME)的电化学行为,该电极在中性(pH7.0~8.0)条件下性能比纯PB修饰膜更稳定,具有良好的电化学活性和对H2O2的电催化性能。氧化峰电流与H2O2浓度在1×10-6~5×10-3mol/L范围内呈良好线性关系,为研制基于酶催化反应的电化学生物传感器奠定了良好基础。     

碳纳米管修饰电极同时测定邻苯二酚和对苯二酚

用十二烷基磺酸钠(SDS)分散碳纳米管(CNTs),通过层层组装(LBL)聚二甲基二烯丙基氯化铵(PDDA)和CNTs构筑PDDA/CNTs多层膜电极.利用紫外-可见光谱法对PDDA/CNTs多层膜的组装过程进行监测,用循环伏安法(CV)和差分脉冲伏安法(DPV)研究了邻苯二酚和对苯二酚同时存在时PDDA/CNTs多层膜电极上的电化学行为.结果表明,碳纳米管修饰电极对邻苯二酚和对苯二酚有较好的电催化活性和电分离作用,邻苯二酚和对苯二酚无需经过分离即可同时被检出.在修饰电极上的线性范围如下:邻苯二酚为2.0×10-6~1.4×10-4mol/L,线性相关系数R=0.9991;对苯二酚为2.0×10-6~1.4×10-4mol/L,线性相关系数R=0.9987.     

碳量子点/聚中性红修饰电极同时检测鸟嘌呤和腺嘌呤

制备了碳量子点/聚中性红膜修饰电极。采用了透射电子显微镜和荧光光谱对制备的碳量子点进行表征。利用循环伏安法、示差脉冲伏安法考察了鸟嘌呤和腺嘌呤在修饰电极上的电化学行为。结果表明,在0.1 mol/L磷酸盐缓冲溶液中,该修饰电极对鸟嘌呤和腺嘌呤的氧化具有明显的电催化作用。在最佳条件下,鸟嘌呤和腺嘌呤的示差脉冲伏安响应和其浓度分别在1.0×10~(-6)~2.0×10~(-4)mol/L和5.0×10~(-6)~2.0×10~(-4)mol/L范围中呈良好的线性关系,检测限分别为3.0×10~(-7)mol/L和4.8×10~(-7)mol/L(S/N=3)。该修饰电极能够用于复杂样品中鸟嘌呤和腺嘌呤的检测及实际样品分析。     

多壁碳纳米管-聚茜素红膜修饰电极测定多菌灵

制备了多壁碳纳米管-聚茜素红膜(MWNT-PAR)修饰电极,用循环伏安法和线性扫描伏安法、计时电量法等研究多菌灵在修饰电极上的电化学行为.结果表明,多菌灵在MWNT-PAR修饰电极上是扩散控制的不可逆电氧化过程.实验测定了部分电极过程参数,并发现多菌灵氧化峰电流的一阶导数值与其浓度在5.0×10~(-6)～1.0×10~(-4) mol/L范围内呈线性关系,回归方程为:I_p ′(A)=-3.112×10~(-6)-1.198c(mol/L),R=-0.9953,其检出限为2.0×10~(-7) mol/L,回收率为99.0%～105.6%.     

聚对硝基苯偶氮间苯二酚修饰电极伏安法测定多巴胺

采用循环伏安法研究了多巴胺(DA)在聚对硝基苯偶氮间苯二酚(p-nitrobenzenazo resorcinol,简称NBAR)膜修饰电极上的电化学行为,用差示脉冲伏安法对多巴胺的含量进行测定.结果表明,聚NBAR膜修饰电极对DA有明显的电催化作用.在pH4.0的磷酸盐缓冲液中,氧化峰电流与DA浓度在5.0×10-6~8.0×10-4mol/L范围内呈良好的线性关系,检测限为6.0×10-7mol/L.修饰电极可有效消除针剂中其它组分对DA测定的干扰,已用于实际样品DA含量的测定,结果令人满意.     

普鲁士蓝膜电化学行为的EQCM研究

应用循环伏安法于铂电极上电化学沉积PB膜,并由电化学石英晶体微天平技术(EQCM)原位测量了PB膜电沉积过程的频率响应.研究表明,沉积液中添加邻菲咯啉对PB膜结构有影响.有邻菲咯啉参与沉积的PB Pt/QCM电极对H2O2的电催化还原性能优于不含邻菲咯啉沉积液制备的PB Pt/QCM电极.     

水杨酸在多壁碳纳米管修饰电极上的电化学行为及其测定

用循环伏安法(CV)研究了水杨酸(SA)在多壁碳纳米管修饰玻碳电极上的电化学行为,并初步探讨了反应机理.实验结果表明,水杨酸在该电极上为一个2e/H~+的完全不可逆过程.在pH=5.0的磷酸盐缓冲溶液(PBS)中,用循环伏安法在该电极上测定了水杨酸.方法线性范围为2.0×10~(-5)～1.0×10~(-3)mol/L,检出限为8.93×10~(-6)mol/L.将该电极用于药品分析,结果令人满意.     

Au-Pd合金纳米管修饰的尼古丁分子印迹膜传感器的研究

基于Au-Pd合金修饰的玻碳电极为工作电极,采用循环伏安法将邻氨基酚与尼古丁电沉积在工作电极上,制备了尼古丁分子印迹膜传感器。采用差分脉冲伏安法研究尼古丁在尼古丁分子印迹膜传感器上的电化学行为,考察了模板溶解时间、富集时间和溶液pH值对尼古丁测定的影响。在优化实验条件下,尼古丁分子印迹膜传感器的线性范围为1.2×10~(-7)~2.5×10~(-3) mol/L,检出限为4.6×10~(-8) mol/L。用该传感器对吸烟者血液中尼古丁的含量进行检测,结果表明,该传感器具有灵敏度高、线性范围宽、重现性及稳定性好等优点。     

普鲁士蓝膜修饰电极的电化学阻抗谱

测量了应用电化学方法制备的不同厚度的普鲁士蓝膜修饰电极的循环伏安行为与电化学阻抗谱.由所得到的循环伏安图讨论了普鲁士蓝修饰膜的氧化还原过程,并对相关的Nyquist图进行了解析,提出了相应的等效电路.在此基础上计算出较薄膜中普鲁士蓝/普鲁士白电化学反应的表观速率常数和表观扩散系数,讨论了膜厚度对电荷扩散的影响.当膜相对较薄时,电极过程主要由动力学过程控制;当膜达到一定厚度时,电荷在膜中的扩散速率受到限制,电极过程由动力学过程和电荷扩散过程共同控制,证实了文献报导的普鲁士蓝膜修饰电极为多层空间分布电荷传递模型.     

化学修饰电极的研究—Ⅸ.普鲁士蓝修饰电极的制备和性能

本文用电化学方法在Pt基体上制备出更稳定的普鲁士蓝修饰电极,可经历0.6—1.1V(Vs.SCE)之间连续一千周以上电位扫描;提出了普鲁士蓝薄膜电化学氧化还原时电子转移的多层模型;系统地研究了电极制备条件、薄膜厚度及溶液pH值对电极伏安行为的影响。     

Enhancement of the Electrochemical Performance of Prussian Blue Modified Electrode via Ionic Liquid Treatment

This article first reports the preparation of a Prussian blue (PB) modified electrode with improved electrochemical properties at the functionalized glass carbon electrode (GC) by imidazolium based ionic liquid. The molecular ionic liquid film on the GC electrode has been found to influence the electrodeposition of PB by a way of enhancement of voltammetric currents, suggesting efficient electrodepositon. Such efficient electrodeposition was caused by the static electric effect which existed between the positively charged imidazolium group on the electrode surface and the negative ferric‐ferricyanide in solution. Compared with the PB/GC electrode, the PB/[Bmim][Cl]/GC electrode showed much better electrochemical stability after successive potential cycling for 250 cycles. A comparative study on amperometric responses of both electrodes to reduce H₂O₂ was also investigated. PB/[Bmim][Cl]/GC electrode showed a better electrocatalytic performance to H₂O₂ with wider linear detection range and higher sensitivity than that at the electrode without [Bmim][Cl]. Furthermore, the kinetics for both electrodes was discussed. The PB/[Bmim][Cl]/GC electrode possessed a greater diffusion coefficient.     

Electrochemical Fabrication of Prussian Blue Nanocube‐decorated Electroreduced Graphene Oxide for Amperometric Sensing of NADH

In this study, Prussian blue (PB) film on the electroreduced graphene oxide (ERGO)‐modified Au electrode surface (ERGO/PB) is easily prepared by means of cyclic voltammetric technique in the mixture of K₃Fe(CN)₆ and FeCl₃. Its electrochemical behaviors for NADH biosensor are studied. The structural and morphological characters of modified electrode material are analyzed with using of XPS, XRD, Raman, EDS, and SEM techniques. ERGO/PB hybrid nanocomposite for NADH biosensor is exhibited to the higher catalytic effect (linear range from 1.0 to 100 μM, detection limit of 0.23 μM at S/N=3) compared to naked Au, ERGO‐modified Au, and PB‐modified Au electrodes. In addition to, ERGO/PB electrode was used to voltammetric and amperometric detection of H₂O₂. ERGO/PB electrodes also showed the same behavior as the NADH sensor. This ERGO/PB‐modified electrode supplied a simple, new, and low‐cost route for amperometric sensing of both NADH and H₂O₂.     

Voltammetric and amperometric determination of ascorbic acid at a chemically modified carbon fibre microelectrode

A carbon fibre microelectrode was modified by electrodeposition of a thin copper-heptacyanonitrosylferrate (CuHNF) film on its surface. The film showed the ability to catalyse electrochemical oxidation of ascorbic acid. The catalytic reaction was limited either by diffusion, or by the electrochemical reaction of the catalyst. A linear, cyclic voltammetric response for ascorbic acid was obtained between 5.0 x 10(-5) and 6.0 x 10(-3)M. By amperometric measurements the linear range could be extended to 8.0 x 10(-6)-2.0 x 10(-3)M. The modified electrode showed good stability and reproducibility.     

Electrocatalytic oxidation of thiosulfate on a modified nickel hexacyanoferrate film electrode

Summary A modified nickel hexacyanoferrate film glassy carbon electrode is prepared by the electrochemical deposition technique. The film is very stable upon voltammetric scanning in the potential range of 1.0 to –0.5 V (vs. SCE) and an oxidation peak occurs at 0.35 V (vs. SCE) (1 mol/l NaNO₃). The effects of electrolyte, solvent, coexisting ions and other variables on the voltammetric behaviour of the modified film have been studied. The thickness of the resulting film can be controlled by changing the number of voltammetric cycles and the concentrations of nickel(II) and hexacyanoferrate(III) ions. The film shows catalytic activity towards electrooxidation of thiosulfate with a peak potential +0.5 V (K^–-containing media). This oxidation potential of thiosulfate on the modified electrode is shifted negatively by about 550 mV as compared to the naked glassy carbon electrode. For practical application, the modified electrode can be used for the determination of thiosulfate in concentrations from 5.0×10^–5 to 1.0×10^–1 mol/l. This method has been successfully applied to the determination of thiosulfate in photographic waste effluents.     

维生素B1的电化学聚合及催化作用

用循环伏安法在石墨电极上制备了VB1聚合膜修饰电极,VB1聚合膜在pH5的PBS中有一对氧化还原峰,峰电位Epd=350mV,Epc=325mV,峰电流与扫描速率的平方根成正比,表明电子在膜中的传递为扩散控制,且聚合膜与VB1单体有不同的电化学性质。实验表明VB1聚合膜对多巴胺、肾上腺素等神经递质有显著的电催化作用。     

Polybenzoin Based Sensor for Determination of 2thiouracil in Biological Fluids and Pharmaceutical Formulations

A carbon paste electrode was modified by electropolymerisation of benzoin using voltammetric technique. A novel polybenzoin modified carbon paste electrode (PB‐CPE) was developed for use as a detector in cyclic voltammetry and differential pulse adsorptive stripping voltammetry for the sensitive determination of 2thiouracil (2TU). The atomic force microscopy was applied to characterize the surface morphology of PB‐CPE. The modified electrode showed excellent electrocatalytic activity for the oxidation of 2TU. The oxidation process was irreversible over the pH range studied and exhibited a diffusion controlled behavior. All experimental parameters have been optimized. The peak current for the stripping of 2TU was found to be linear over the concentration range of 0.2–1.2 µM, with a detection limit of 2.21 nM. The practical application of the PB‐CPE in the determination of 2TU in human biological fluids and pharmaceutical samples were demonstrated that it has high sensitivity and good selectivity.     

Surface modification of a planar electrochemical microcell

The fabrication of a three-electrode electrochemical microcell in which the working electrode is selectively modified with poly (vinylferrocene) (PVFer) is described for use as a chemical sensor. The microcell was characterized by cyclic voltammetric and differential-pulse voltammetric techniques and the behaviour of the PVFer-modified platinum electrode in contact with 0.1 M KCl is reported. The mediating properties of the PVFer film are demonstrated for this cell by using the oxidation of ascorbic acid, a process which is shown to be slow at the corresponding bare platinum microelectrode.     

TiO2 phytate films as hosts and conduits for cytochrome c electrochemistry

Cytochrome c is accumulated into a film of TiO(2) nanoparticles and phytate by adsorption from an aqueous solution into the mesoporous structure. Stable voltammetric responses and high concentrations of redox protein within the TiO(2) phytate layer can be achieved. Two types of electrode systems are reported with (i) the modified TiO(2) phytate film between electrode and aqueous solution phase and (ii) the modified TiO(2) phytate film buried under a porous gold electrode ('porotrode'). The electrical conductivity of TiO(2) phytate films is measured and compared in the dry and in the wet state. Although in the dry state essentially insulating, the TiO(2) phytate film turns into an electrical conductor (with approximately 4 Omega cm specific resistivity assuming ohmic behaviour) when immersed in aqueous 0.1 M phosphate buffer solution at pH 7. The redox protein cytochrome c is therefore directly connected to the electrode via diffusion and migration of electrons in the three dimensional mesoporous TiO(2) phytate host structure. Electron transfer from cytochrome c to TiO(2) is proposed to be the rate-determining step for this conduction mechanism.