Construction of a new Cu2+ coated wire ion selective electrode based on 2-((2-(2-(2-(2-hydroxy-5-methoxybenzylidene amino)phenyl)disufanyl)phenylimino)methyl)-4-methoxyphenol Schiff base

In this article a new coated platinum Cu²⁺ ion selective electrode based on 2-((2-(2-(2-(2-hydroxy-5-methoxybenzylideneamino)phenyl)disufanyl)phenylimino) methyl)-4-methoxyphenol Schiff base (L₁) as a new ionophore is described. This sensor has a wide linear range of concentration (1.2 × 10⁻⁷-1.0 × 10⁻¹ mol L⁻¹) and a low detection limit of 9.8 × 10⁻⁸ mol L⁻¹of Cu(NO₃)₂. It has a Nernstian response with slope of 29.54 ± 1.62 mV decade⁻¹ and it is applicable in the pH range of 4.0-6.0 without any divergence in potentioal. The coated electrode has a short response time of approximately 9 s and is stable at least for 3.5 months. The electrode shows a good selectivity for Cu²⁺ ion toward a wide variety of metal ions. The proposed sensor was successfully applied for the determination of Cu²⁺ ion in different real and environmental samples and as indicator electrode for potentiometric titration of Cu²⁺ ion with EDTA.     

Mesoporous silica-based electrochemical sensor for sensitive determination of environmental hormone bisphenol A

Bisphenol A (BPA) is an emerging contaminant with severe toxic effects such as disrupting endocrine system or causing cancer, therefore, developing sensitive and selective sensor for BPA is very important and interesting. Herein, MCM-41, a kind of mesoporous silica, was synthesized and then used to prepare an electrochemical sensor for BPA. For better comparison, carbon nanotubes, activated carbon, silica gel and graphite were also employed to prepare electrochemical sensor for BPA. The electrochemical behaviors of BPA at different electrochemical sensors were investigated. Compared with other sensors, the MCM-41 sensor greatly enhances the response signal of BPA due to the large active surface area and high accumulation efficiency. The effects of pH value, accumulation time and sensor composition were examined. The linear range is from 2.2 × 10⁻⁷ to 8.8 × 10⁻⁶ mol L⁻¹, and the limit of detection is evaluated to be 3.8 × 10⁻⁸ mol L⁻¹. Finally, the MCM-41 sensor was successfully employed to determine BPA in water samples.     

Highly selective and sensitive paper-based colorimetric sensor using thiosulfate catalytic etching of silver nanoplates for trace determination of copper ions

A novel, highly selective and sensitive paper-based colorimetric sensor for trace determination of copper (Cu²⁺) ions was developed. The measurement is based on the catalytic etching of silver nanoplates (AgNPls) by thiosulfate (S₂O₃²⁻). Upon the addition of Cu²⁺ to the ammonium buffer at pH 11, the absorption peak intensity of AuNPls/S₂O₃²⁻ at 522 nm decreased and the pinkish violet AuNPls became clear in color as visible to the naked eye. This assay provides highly sensitive and selective detection of Cu²⁺ over other metal ions (K⁺, Cr³⁺, Cd²⁺, Zn²⁺, As³⁺, Mn²⁺, Co²⁺, Pb²⁺, Al³⁺, Ni²⁺, Fe³⁺, Mg²⁺, Hg²⁺ and Bi³⁺). A paper-based colorimetric sensor was then developed for the simple and rapid determination of Cu²⁺ using the catalytic etching of AgNPls. Under optimized conditions, the modified AgNPls coated at the test zone of the devices immediately changes in color in the presence of Cu²⁺. The limit of detection (LOD) was found to be 1.0 ng mL⁻¹ by visual detection. For semi-quantitative measurement with image processing, the method detected Cu²⁺ in the range of 0.5–200 ng mL⁻¹(R² = 0.9974) with an LOD of 0.3 ng mL⁻¹. The proposed method was successfully applied to detect Cu²⁺ in the wide range of real samples including water, food, and blood. The results were in good agreement according to a paired t-test with results from inductively coupled plasma-optical emission spectrometry (ICP-OES).     

Extraction of trace amounts of silver on various amino-functionalized nanoporous silicas in real samples

Aminopropyl-functionalized mesoporous silicas, NH₂-MCM-41 and NH₂-SBA-15, as absorbents were utilized for rapid extraction, preconcentration and determination of trace amounts of silver. Flow rates of sample and eluent, pH, eluent solution, type, concentration and the least amount of eluent for desorption of silver ions were optimized; moreover, break through volume and the effect of various cationic interferences on the sorption of silver were evaluated. The extraction efficiency of silver ions was greater than 95% for MCM-41-NH₂ and 85% for SBA-15-NH₂ and the limit of detection (LOD) was less than 4 ng mL^?1 for both functionalized mesoporous silicas. The preconcentration factor was greater than 210 and the relative standard deviation (RSD) was <2%. The adsorption capacity of the mesoporous silicas is higher than 143 mg g^?1 for NH₂-MCM-41 and 137 mg g^?1 for NH₂-SBA-15. Under similar experimental conditions the results for these solid phases were compared with each other. NH₂-SBA-15, in spite of larger pore size diameter and adsorption of silver ions in higher flow rates has lower recovery and a higher RSD compared to MCM-41. This method has been applied to determine silver in photographic emulsions and real samples.     

Effect of dimensions of multi-walled carbon nanotubes on its enrichment efficiency of metal ions from environmental waters

The effect of dimensions (length and external diameter) of multi-walled carbon nanotubes (MWCNTs) on its preconcentration efficiency towards some metal ions (Pb²⁺, Cd²⁺, Cu²⁺, Zn²⁺ and MnO₄⁻) from environmental waters prior to their analysis by flame atomic absorption spectroscopy (FAAS) was investigated. MWCNTs (as-received from the manufacturer) of various external diameters and lengths were involved. Other variables optimized included effects of pH of water sample, composition and volume of eluent, mass of the MWCNTs, breakthrough volume and coexisting ions. Maximum recovery of metal ions was obtained at pH 9 where it was thought that precipitation of metals as their hydroxides played the major factor in metals uptake by MWCNT. It was suggested that the use of appropriate dimensions of MWCNTs may support the trapping process of the precipitated metal hydroxides by MWCNTs. It was found that long MWCNT of length 5-15 μm and external diameter 10-30 nm gave the highest enrichment efficiency towards almost all the targeted metal ions. It could be used for preconcentration of MnO₄⁻, Cu²⁺, Zn²⁺ and Pb²⁺ with almost full recovery; but not for Cd²⁺ due to its low recovery. The optimized solid phase extraction (SPE) procedure was capable of determining metal ions in the linear range 20-100 ng mL⁻¹ (except for Zn²⁺ from 20 to 150 ng mL⁻¹). Detection limits were 0.709 ng mL⁻¹ for MnO₄⁻, 0.278 ng mL⁻¹ for Pb²⁺, 0.465 ng mL⁻¹ for Cu²⁺, 0.867 ng mL⁻¹ for Zn²⁺. Application of the optimized SPE procedure to environmental waters (tap water, reservoir water and stream water) gave spike recoveries of the metals in the range of 81-100%.     

Simultaneous extraction and preconcentration of uranium and thorium in aqueous samples by new modified mesoporous silica prior to inductively coupled plasma optical emission spectrometry determination

A new synthesized modified mesoporous silica (MCM-41) using 5-nitro-2-furaldehyde (fural) was applied as an effective sorbent for the solid phase extraction of uranium(VI) and thorium(IV) ions from aqueous solution for the measurement by inductively coupled plasma optical emission spectrometry (ICP OES). The influences of some analytical parameters on the quantitative recoveries of the analyte ions were investigated in batch method. Under optimal conditions, the analyte ions were sorbed by the sorbent at pH 5.5 and then eluted with 1.0 mL of 1.0 mol L⁻¹ HNO₃. The preconcentration factor was 100 for a 100 mL sample volume. The limits of detection (LOD) obtained for uranium(VI) and thorium(IV) were 0.3 μg L⁻¹. The maximum sorption capacity of the modified MCM-41 was found to be 47 and 49 mg g⁻¹ for uranium(VI) and thorium(IV), respectively. The sorbent exhibited good stability, reusability, high adsorption capacity and fast rate of equilibrium for sorption/desorption of uranium and thorium ions. The applicability of the synthesized sorbent was examined using CRM and real water samples.     

Sensitive pseudobienzyme electrocatalytic DNA biosensor for mercury(II) ion by using the autonomously assembled hemin/G-quadruplex DNAzyme nanowires for signal amplification

Herein, a novel sensitive pseudobienzyme electrocatalytic DNA biosensor was proposed for mercury ion (Hg²⁺) detection by using autonomously assembled hemin/G-quadruplex DNAzyme nanowires for signal amplification. Thiol functionalized capture DNA was firstly immobilized on a nano-Au modified glass carbon electrode (GCE). In presence of Hg²⁺, the specific coordination between Hg²⁺ and T could result in the assembly of primer DNA on the electrode, which successfully triggered the HCR to form the hemin/G-quadruplex DNAzyme nanowires with substantial redox probe thionine (Thi). In the electrolyte of PBS containing NADH, the hemin/G-quadruplex nanowires firstly acted as an NADH oxidase to assist the concomitant formation of H₂O₂ in the presence of dissolved O₂. Then, with the redox probe Thi as electron mediator, the hemin/G-quadruplex nanowires acted as an HRP-mimicking DNAzyme that quickly bioelectrocatalyzed the reduction of produced H₂O₂, which finally led to a dramatically amplified electrochemical signal. This method has demonstrated a high sensitivity of Hg²⁺ detection with the dynamic concentration range spanning from 1.0 ng L⁻¹ to 10 mg L⁻¹ Hg²⁺ and a detection limit of 0.5 ng L⁻¹ (2.5 pM) at the 3S_blank level, and it also demonstrated excellent selectivity against other interferential metal ions.     

Non-chromatographic determination of ultratraces of V(V) and V(IV) based on a double column solid phase extraction flow injection system coupled to electrothermal atomic absorption spectrometry

In this work, a non-chromatographic procedure for the on-line determination of ultratraces of V(V) and V(IV) is presented. The method involves a solid phase extraction-flow injection system coupled to electrothermal atomic absorption spectrometry (SPE-FI-ETAAS). The system holds two microcolumns (MC) set in parallel and filled with lab-made mesoporous silica functionalized with 3-aminopropyltriethoxy silane (APS) and mesoporous silica MCM-41, respectively. The pre-concentration of V(V) is performed by sorption onto the first MC (C1) filled with APS at pH 3, whilst that of V(IV) is performed by sorption onto the second column (C2) filled with mesoporous silica MCM-41 at pH 5. Aqueous samples containing both analytes are loaded and, after pre-concentration (pre-concentration factor PCF = 10, sorption flow rate = 1 mL min⁻¹, sorption time = 10 min), they are eluted in separate vessels with hydroxylammonium chloride (HC) 0.1 mol L⁻¹ in HCl 0.5 mol L⁻¹ (elution volume = 1 mL, elution flow rate = 0.5 mL min⁻¹). Afterwards, both analytes are determined through ETAAS with graphite furnace. Under optimized conditions, the main analytical figures of merit for V(V) and V(IV) are, respectively: detection limits (3 s): 0.5 and 0.6 μg L⁻¹, linear range: 2-100 μg L⁻¹ (both analytes), sensitivity: 0.015 and 0.013 μg⁻¹ L and sample throughput: 6 h⁻¹ (both analytes). Recoveries of both species were assayed in different water samples. Validation was performed through certified reference materials for ultratraces of total vanadium in river water.     

Highly sensitive and selective amperometric sensors for nanomolar detection of iodate and periodate based on glassy carbon electrode modified with iridium oxide nanoparticles

Iridium oxide nanoparticles are grown on a glassy carbon electrode by electrodepositing method. The electrochemical behavior and electrocatalytic activity of modified electrode towards reduction of iodate and periodate are studied. The reductions of both ions occur at the unusual positive peak potential of 0.7 V vs. reference electrode. The modified electrode is employed successfully for iodate and periodates detection using cyclic voltammetry, hydrodynamic amperometry and flow injection analysis (FIA). In the performed experiments, flow injection amperometric determination of iodate and periodate yielded calibration curves with the following characteristics: linear dynamic range up to 100 and 80 μM, sensitivity of 140.9 and 150.6 nA μM⁻¹ and detection limits of 5 and 36 nM, respectively. The repeatability of the modified electrode for 21 injections of 1.5 μM of iodate solution is 1.5%. The interference effects of NO₂⁻, NO₃⁻, ClO₃⁻, BrO₃⁻, ClO₄⁻, SO₄²⁻, Cu²⁺, Zn²⁺, Mn²⁺, Mg²⁺, Cd²⁺, Ca²⁺, Na⁺, K⁺, NH₄⁺ and K⁺, CH₃COO⁻ and glucose were negligible at the concentration ratio of more than 1000. The obtained attractive analytical performance together with high selectivity and simplicity of the proposed method provide an effective and e novel modified electrode to develop an iodate and periodate sensor. Sensitivity, selectivity, the liner concentration range and the detection limit of the developed sensor are all much better than all known similar sensors in the literature for iodate and periodate determination.     

Synthesis of salicylaldehyde-modified mesoporous silica and its application as a new sorbent for separation, preconcentration and determination of uranium by inductively coupled plasma atomic emission spectrometry

A new functionalized mesoporous silica (MCM-41) using salicylaldehyde was utilized for the separation, preconcentration and determination of uranium in natural water by inductively coupled plasma atomic emission spectrometry (ICP-AES).Experimental conditions for effective adsorption of trace levels of U(VI) were optimized. The preconcentration factor was 100 (1.0 mL of elution for a 100 mL sample volume). The analytical curve was linear in the range 2-1000 μg L⁻¹ and the detection limit was 0.5 ng mL⁻¹. The relative standard deviation (R.S.D.) under optimum conditions was 2.5% (n = 10). Common coexisting ions did not interfere with the separation and determination of uranium at pH 5. The sorbent exhibited excellent stability and its sorption capacity under optimum conditions has been found to be 10 mg of uranium per gram of sorbent. The method was applied for the recovery and determination of uranium in different water samples.     

Langmuir-Blodgett film of p-tert-butylthiacalix[4]arene modified glassy carbon electrode as voltammetric sensor for the determination of Hg(II)

The π-A isotherms and UV-vis spectra of the transferred films suggested that the monolayer of p-tert-butylthiacalix[4]arene can coordinate with Hg²⁺ at the air-water surface. From these observations, a glassy carbon electrode coated with Langmuir-Blodgett film of p-tert-butylthiacalix[4] arene as a new voltammetric sensor is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode and modified glassy carbon electrode using direct coating method, the Langmuir-Blodgett film-modified electrode can greatly improve the measuring sensitivity of Hg²⁺. Under the selected conditions, the Langmuir-Blodgett film-modified electrode in 0.1 mol L⁻¹ H₂SO₄ + 0.01 mol L⁻¹ KCl solution shows a linear voltammetric response for Hg²⁺ in the range of 5.0 × 10⁻¹⁰ to 1.5 × 10⁻⁷ mol L⁻¹, with a detection limit of 2.0 × 10⁻¹⁰ mol L⁻¹. The proposed method was also applied to determine Hg²⁺ in water samples (tap, lake and river water). In addition, the fabricated electrode exhibited a distinct advantage of simple preparation, non-toxicity, good reproducibility and good stability.     

Synthesis of Cu-mediated nano-sized salbutamol-imprinted polymer and its use for indirect recognition of ultra-trace levels of salbutamol

Cu²⁺-mediated salbutamol-imprinted polymer nanoparticles, synthesized by precipitation polymerization, were mixed with graphite powder and n-eicosane in order to fabricate a modified carbon paste electrode. This electrode was then applied for indirect differential pulse voltammetry determination of salbutamol. In the presence of Cu²⁺ ions, the formed Cu²⁺–salbutamol complex was adsorbed in to the pre-designed cavities of the MIP particles, situated on the electrode surface. Since the electrochemical signal of salbutamol was intrinsically small, the oxidation peak of the participant Cu²⁺, after reduction step, was recorded and used as an indication of salbutamol amount, adsorbed in the electrode. Different variables influencing the sensor performance were studied and the best conditions were chosen for the determination purpose. Correlation between the sensor response to salbutamol and its concentration was linear in the range of 1.0 × 10⁻⁹–5.5 × 10⁻⁸ M. Detection limit was calculated equal to 6.0 × 10⁻¹⁰ M (S/N). Five replicated determination of salbutamol (1 × 10⁻⁸ M) resulted in standard error of 3.28%, meaning a satisfactory precision of the determination method. The prepared sensor was applied for real sample analysis. In order to minimize the interference effect, the synthesized polymer was successfully used as a solid phase sorbent for salbutamol extraction, before analysis of real samples by the developed sensor.     

Simultaneous determination of Mn(II), Cu(II) and Fe(III) as 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol complexes by adsorptive cathodic stripping voltammetry at a carbon paste electrode

A simple and precise square-wave adsorptive cathodic stripping voltammetry (SW-AdCSV) method has been described for simultaneous determination of Mn(II), Cu(II) and Fe(III) in water samples using a carbon paste electrode. In 0.1 mol L⁻¹ acetate buffer (pH 5) containing 50 μmol L⁻¹ of 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol (5-Br-PADAP), Mn(II), Cu(II) and Fe(III) were simultaneously determined as metal-complexes with 5-Br-PADAP following preconcentration onto the carbon paste electrode by adsorptive accumulation at +1.0 V (vs. Ag/AgCl/3 M KCl). Insignificant interference from various cations (K⁺, Na⁺, Mg²⁺, Ca²⁺, Al³⁺, Bi³⁺, Sb³⁺, Se⁴⁺, Zn²⁺, Ni²⁺, Co²⁺, Cd²⁺, Pb²⁺, V⁵⁺, Ti⁴⁺ and NH₄⁺), anions (HCO₃⁻, Cl⁻, NO³⁻, SO₄²⁻ and PO₄³⁻) and ascorbic acid was noticed. Limits of detection of 0.066, 0.108 and 0.093 μg L⁻¹ and limits of quantitation of 0.22, 0.36 and 0.31 μg L⁻¹ Mn(II), Cu(II) and Fe(III), respectively, were achieved by the described method. The described stripping voltammetry method was successfully applied for simultaneous determination of Mn(II), Cu(II) and Fe(III) in ground, tap and bottled natural water samples.     

Synthesis and characterization of novel ion-imprinted polymeric nanoparticles for very fast and highly selective recognition of copper(II) ions

This work reports the preparation of new Cu²⁺ ion-imprinted polymeric nanoparticles using 1-hydroxy-4-(prop-2′-enyloxy)-9,10-anthraquinone (AQ) as a vinylated chelating agent. The Cu²⁺ ion found to form a stable 1:1 complex with AQ in methanol solution. The resulting Cu²⁺-AQ complex was copolymerized with ethyleneglycol dimethacrylate, as a cross-linking monomer, via precipitation polymerization method. The imprint copper ion was removed from the polymeric matrix using a 0.1 mol L⁻¹ HNO₃ solution. The Cu²⁺-imprinted polymeric nanoparticles were characterized by IR spectroscopy, scanning electron microscopy (SEM) and N₂ adsorption-desorption isotherms. The SEM micrographs showed colloidal nanoparticles of 60-100 nm in diameter and slightly irregular in shape. Optimum pH for maximum sorption was 7.0. Sorption and desorption of Cu²⁺ ion on the IIP nanoparticles were quite fast and achieved completely over entire investigated time periods of 2-30 min. Maximum sorbent capacity and enrichment factor of the prepared IIP for Cu²⁺ were 73.8 μmol g⁻¹ and 56.5, respectively. The relative standard deviation and limit of detection (C_LOD = 3S_b/m) of the method were evaluated as 2.6% and 0.1 ng mL⁻¹, using inductively coupled plasma-atomic emission spectrometry, respectively. It was found that the imprinting technology results in increased affinity of the prepared material toward Cu²⁺ ion over other metal ions with the same charge and close ionic radius. The relative standard deviations for six and twenty replicates with the same nanoparticles were found to be 1.7% and 2.1%, respectively.     

Determination of mercury species by the diffusive gradient in thin film technique and liquid chromatography – atomic fluorescence spectrometry after microwave extraction

A diffusive gradient in thin films technique (DGT) was combined with liquid chromatography (LC) and cold vapor atomic fluorescence spectrometry (CV-AFS) for the simultaneous quantification of four mercury species (Hg²⁺, CH₃Hg⁺, C₂H₅Hg⁺, and C₆H₅Hg⁺). After diffusion through an agarose diffusive layer, the mercury species were accumulated in resin gels containing thiol-functionalized ion-exchange resins (Duolite GT73, and Ambersep GT74). A microwave-assisted extraction (MAE) in the presence of 6 M HCl and 5 M HCl (55 °C, 15 min) was used for isolation of mercury species from Ambersep and Duolite resin gels, respectively. The extraction efficiency was higher than 95.0% (RSD 3.5%). The mercury species were separated with a mobile phase containing 6.2% methanol + 0.05% 2-mercaptoethanol + 0.02 M ammonium acetate with a stepwise increase of methanol content up to 80% in the 16th min on a Zorbax C18 reverse phase column. The LODs of DGT–MAE–LC–CV-AFS method were 38 ng L⁻¹ for CH₃Hg⁺, 13 ng L⁻¹ for Hg²⁺, 34 ng L⁻¹ for C₂H₅Hg⁺ and 30 ng L⁻¹ for C₆H₅Hg⁺ for 24 h DGT accumulation at 25 °C.     

Kinetic method for determination of nanogram amounts of copper(II) by its catalytic effect on hexacynoferrate(III)-citric acid indicator reaction

This paper describes a highly sensitive, selective catalytic-kinetic-spectrophotometric method for the determination of copper(II) concentration as low as 6 ng ml⁻¹. The method is based on the catalytic effect of copper(II) on the oxidation of citric acid by alkaline hexacyanoferrate(III). The reaction was followed by measuring the decrease in absorbance of hexacyanoferrate(III) at 420 nm (λ_max of [Fe(CN)₆]³⁻, ∈ = 1020 dm³ mol⁻¹ cm⁻¹). The dependence of rate of the indicator reaction on the reaction variables has been studied and discussed to propose a suitable mechanism to get a relation between the reaction rate and [Cu²⁺]. A fixed time procedure has been used to obtain a linear calibration curve between the initial rate and lower [Cu²⁺] or log[Cu²⁺] in the range 1 × 10⁻⁷ to 4 × 10⁻⁴ mol l⁻¹ (6.35-25,400 ng ml⁻¹). The detection limit has been calculated to be 4 ng ml⁻¹. The maximum average error is 3.5%. The effect of the presence of various cations, commonly associated with copper(II) and some anions has also been investigated and discussed. The proposed method is sensitive, accurate, rapid and inexpensive compared to other techniques available for determination of copper(II) in such a large range of concentration. The new method has been successfully applied for the determination of copper(II) in various samples.     

Luminescent core–shell Ca2MoO5:Eu3+-MCM-41 structure for sustained drug release

The spherical mesoporous MCM-41 coated with a novel Ca₂MoO₅:Eu³⁺ phosphor layer was prepared for the first time. The obtained Ca₂MoO₅:Eu³⁺-MCM-41 was characterized via XRD and FT-IR. The crystal system of the Ca₂MoO₅ phase was determined to be orthorhombic, and its space group was found to be Ima2 (46), and its cell parameters were a = 16.175, b = 5.1514, c = 5.6977 A°; α = β = γ = 90°. The particle dimensions of MCM-41 and Ca₂MoO₅:Eu³⁺-MCM-41 nanoparticles were determined to be 260 nm and 229 nm via scanning electron microscopy analysis. Bortezomib was loaded into the Ca₂MoO₅:Eu³⁺-MCM-41 nanoparticles under scCO₂ at 200 bars and 40 °C. The results of the TG analysis showed that the amount of drug-loaded to MCM-41 and Ca₂MoO₅:Eu³⁺-MCM-41 nanoparticles were determined to be 14.02% and 3.02%, respectively. The BET analysis showed that while the specific surface area and pore volume of MCM-41 and Ca₂MoO₅:Eu³⁺ before Bortezomib (BTZ) loading were 1,506 m²/g and 267 m²/g, respectively, after drug loading these values were found to decrease to 488 m²/g and 7.883 m²/g. It was determined that BTZ was released from the nanoparticles in a sustained manner over 66 h. The R² value, which was calculated to be 0.9739, indicated that the release kinetic of BTZ followed the Korsmeyer–Peppas model.     

Fabrication and application of a new modified electrochemical sensor using nano-silica and a newly synthesized Schiff base for simultaneous determination of Cd,Cu and Hg ions in water and some foodstuff samples

A new chemically modified carbon paste electrode was constructed and used for rapid, simple, accurate, selective and highly sensitive simultaneous determination of cadmium, copper and mercury using square wave anodic stripping voltammetry (SWASV). The carbon paste electrode was modified by N,N′-bis(3-(2-thenylidenimino)propyl)piperazine coated silica nanoparticles. Compared with carbon paste electrode, the stripping peak currents had a significant increase at the modified electrode. Under the optimized conditions (deposition potential, −1.100 V vs. Ag/AgCl; deposition time, 60 s; resting time, 10 s; SW frequency, 25 Hz; pulse amplitude, 0.15 V; dc voltage step height, 4.4 mV), the detection limit was 0.3, 0.1 and 0.05 ng mL⁻¹ for the determination of Cd²⁺, Cu²⁺ and Hg²⁺, respectively. The complexation reaction of the ligand with several metal cations in methanol was studied and the stability constants of the complexes were obtained. The effects of different cations and anions on the simultaneous determination of metal ions were studied and it was found that the electrode is highly selective for the simultaneous determination of Cd²⁺, Cu²⁺ and Hg²⁺. Furthermore, the present method was applied to the determination of Cd²⁺, Cu²⁺ and Hg²⁺ in water and some foodstuff samples.     

A new method for electrocatalytic oxidation of ascorbic acid at the Cu(II) zeolite-modified electrode

A new method is developed for the catalytic oxidation of ascorbic acid at graphite zeolite-modified electrode, doped with copper(II) (Cu²⁺A/ZCME). Copper(II) exchanged in zeolite type A acts as catalyst to oxidize ascorbic acid. The modified electrode lowered the overpotential of the reaction by ∼400 mV. First, the electrochemical behavior of copper(II), incorporated in the zeolite type A modified electrode, was studied. The results illustrate that diffusion can control the copper(II)/copper(0) redox process at the Cu²⁺A/ZCME. Then, the behavior of electrocatalytic oxidation reaction for ascorbic acid was researched. The electrode was employed to study electrocatalytic oxidation of ascorbic acid, using cyclic voltammetry and chronoamperometry as diagnostic techniques. The diffusion coefficient of ascorbic acid was equal to 1.028 × 10⁻⁵ cm² s⁻¹. A linear calibration graph was obtained over the ascorbic acid with a concentration range of 0.003-6.00 mmol L⁻¹. The detection limit (DL) of ascorbic acid was estimated as 2.76 × 10⁻⁷ mol L⁻¹. The relative standard deviations of 10 replicate measurements (performed on a single electrode at several ascorbic acid concentrations between 3.0 and 200 μmol L⁻¹) were measured between 1.0 and 2.4%.