On-line multidimensional chromatography using packed capillary liquid chromatography and capillary gas chromatography

The introduction of selected fractions from a liquid chromatograph into a gas chromatograph has been described; however, analyses were performed by off-line experiments requiring collection and reinjection of the separate fractions or by on-line procedures where disadvantageously, only a fraction of the separated peak or a well resolved component in a mixture could be introduced into a gas chromatograph. This disadvantage is overcome by the apparatus and method described in this paper, which utilizes a multidimensional chromatography system employing a high efficiency, packed capillary LC column coupled on-line to a capillary gas chromatograph. The liquid chromatograph (so designed) can act as a highly efficient clean-up or chemical class fractionation step prior to introduction into the gas chromatograph, significantly reducing sample preparation times in many applications. Thus minor components in a complex matrix can be determined without prior sample clean-up, an example of which is the determination of polychlorinated biphenyls in a complex hydrocarbon matrix.     

Porous ceramic bed supports for fused silica packed capillary columns used in liquid chromatography

Porous ceramic bed supports for fused silica packed capillary columns utilized in liquid chromatography were prepared by polymerizing solutions containing potassium silicate in-situ within a column to create a mechanically stable, rugged, and easily constructed termination. The effect of the bed support length on efficiency, and comparisons to glass wool bed supports, were considered in terms of column efficiencies and hydrodynamic variables. Results obtained indicate better performance for the ceramic bed support.     

Performance evaluation of long monolithic silica capillary columns in gradient liquid chromatography using peptide mixtures

A systematic study is reported on the performance of long monolithic capillary columns in gradient mode. Using a commercial nano-LC system, reversed-phase peptide separations obtained through UV-detection were conducted. The chromatographic performance, in terms of conditional peak capacity and peak productivity, was investigated for different gradient times (varying between 90 and 1320min) and different column lengths (0.25, 1, 2 and 4m) all originating from a single 4m long column. Peak capacities reaching values up to n=10(3) were measured in case of the 4m long column demonstrating the high potential of these long monoliths for the analysis of complex biological mixtures, amongst others. In addition, it was found that the different column fragments displayed similar flow resistance as well as consistent chromatographic performance in accordance with chromatographic theory indicating that the chromatographic bed of the original 4m long column possessed a structural homogeneity over its entire length.     

Gas chromatography of plasma amino acids using a wide bore column: Comparison with packed and capillary columns

A procedure is described in which a wide bore glass capillary column is used as an alternative to the more traditional packed column in the analysis of amino acid levels in plasma. The coefficients of variation for all amino acids (with the exception of aspartic acid) were better than 11% with recoveries ranging from 81% to 122%. The data are compared with the corresponding results obtained using a packed column and show significant differences (p < 0.005) between values for glycine, serine, isoleucine, proline, methionine, aspartic acid, phenylalanine, and lysine. A similar comparison between results from the wide bore and the fused-silica open tubular (FSOT) column shows better agreement. Adjustment of chromatographic conditions for the wide bore analysis yields results in good agreement with those from FSOT analysis but which still differe significantly from the backed column data.     

Fast supercritical fluid chromatography of polymers using packed capillary columns

Summary Fast separations of perfluorinated polyethers and polymethylsiloxanes that are composed of 50–80 oligomers were demonstrated in packed capillary column supercritical fluid chromatography (SFC) using a carbon dioxide mobile phase. Separations were accomplished within 10 min using a 13 cm×250 μm i.d. column packed with 2 μm porous octadecyl bonded silica (ODS) particles. Effects of particle diameter of the packing material and pressure programming on separation were investigated, and packed column SFC was compared with open tubular column SFC. Results show that as the particle diameter was decreased from 5 to 3 to 2 μm and the column length was reduced from 85 to 43 to 13 cm, the separation time could be reduced from 70 to 20 to 10 min while still maintaining similar separation (resolution). Short columns packed with small porous particles are very suitable for fast SFC separations of polymers.     

High resolution liquid chromatography with a packed micro glass capillary column

Single, long columns (1–5 m) can be prepared efficiently using reversed phase packings (3–10 μm particle diameter). 1-m columns packed with 3 and 10 μm packing provide 110 000 and 50 000 theoretical plates, respectively. Very efficient columns can resolve highly complex mixtures and difficult-to-separate compounds. Temperature gradient elution is a powerful technique for LC with microbore columns.     

Comparison of packed and capillary columns for quantitative gas chromatography of triglycerides in milk fat

Summary Quantitative gas chromatography of triglycerides in conjunction with established triglyceride formulae can be used to determine various milk fat parameters. Since the evaluation of, for example, iodine number or content of non-milk fats (foreign fats) in milk fat requires only the separation of triglycerides by carbon number and since repeatabilities, especially of the highboiling triglycerides, have been less acceptable with capillary columns in the past, packed columns have been used exclusively. There is, however, an increasing demand for the use of capillary instead of packed columns and to that end the present investigation has been carried out. To achieve a suitable resolution, with this particularly exacting high-temperature application, a short 5 m capillary column of extreme temperature stability has been used. As well as modification of various analytical conditions different injection techniques have been investigated. On-column, PTV and split injection were compared with regard to repeatability. The cold-on-column injection technique was found to produce the best results, being comparable to the excellent precision of a packed column. Thus, a method is now available by means of which the determination of milk fat parameters by the triglyceride formulae, such as the amount of foreign fats in milk fat, can now be carried out with a standardized capillary column.     

Performance of new prototype packed columns for very high pressure liquid chromatography

The reduced heights equivalent to a theoretical plate (HETP) of naphtho[2,3-a]pyrene were measured at room temperature on two sets of new prototype columns designed to be used in very high pressure liquid chromatography (VHPLC). The mobile phase used was pure acetonitrile. The columns are 50, 100, and 150 mm long. Those of the first set are 2.1 mm I.D., those of the second set, 3.0 mm I.D. The performance of these new columns were compared to those of the first generation of VHPLC columns, commercially available in 2.1 mm I.D. The prototype and commercial columns behave similarly at low reduced linear velocities (ν<5$\nu <5$), when the heat effects are negligible. At high flow rates, the shorter prototype columns have a twice better efficiency and less steep C-branches than the commercial columns. In contrast, the C-branch of the 150 mm long prototype columns are slightly steeper than those of the commercial columns. The important contribution to the reduced HETP that is due to the heat effects at high flow rates can in part be accounted for by a band broadening model governed by a flow mechanism with the shortest prototype columns. The sole heat effects cannot, however, explain the mediocre reduced HETPs of the 2.1 and 3.0 I.D. 150 mm long prototype columns. It seems that radial heterogeneity of the flow rate of the long prototype columns is significantly larger than that of the short columns. The contribution of the packing heterogeneity adds up to that of the heat effects to yield a poor column efficiency when sub-2μm$\text{sub-}2\mu \text{m}$ are packed into thin, long column tubes.     

Packed capillary column supercritical fluid chromatography of fat-soluble vitamins using liquid crystal polysiloxane coated particles

Summary Liquid crystal polysiloxane stationary phases were prepared by coating two different polymers on deactivated porous silica particles (10 m diameter, 80 Å pores). Deactivation of the silica particles before coating was necessary to prepare highly efficient and inert stationary phases for supercritical fluid chromatography (SFC). Fat-soluble vitamins E, A, K₁, K₂, D₂, and D₃ were separated on these columns using neat supercritical CO₂ as mobile phase. The analyses were completed within 40 min at 70 °C. The results were compared to those obtained using a capillary column packed with less ordered liquid crystalm,m-cyanobiphenyl-substituted polysiloxane coated particles. Reduced shape selectivity was observed with this cyanobiphenyl phase. The response factors of vitamins A, E, K₁, K₂, D₂, and D₃ when using the flame ionization detector (FID) were determined to be very similar.     

Parameters affecting the separation of intact proteins in gradient-elution reversed-phase chromatography using poly(styrene-co-divinylbenzene) monolithic capillary columns

An experimental study was performed to investigate the effects of column parameters and gradient conditions on the separation of intact proteins using styrene-based monolithic columns. The effect of flow rate on peak width was investigated at constant gradient steepness by normalizing the gradient time for the column hold-up time. When operating the column at a temperature of 60 °C a small C-term effect was observed in a flow rate range of 1–4 μL/min. However, the C-term effect on peak width is not as strong as the decrease in peak width due to increasing flow rate. The peak capacity increased according to the square root of the column length. Decreasing the macropore size of the polymer monolith while maintaining the column length constant, resulted in an increase in peak capacity. A trade-off between peak capacity and total analysis time was made for 50, 100, and 250 mm long monolithic columns and a microparticulate column packed with 5 μm porous silica particles while operating at a flow rate of 2 μL/min. The peak capacity per unit time of the 50 mm long monolithic column with small pore size was superior when the total analysis time is below 120 min, yielding a maximum peak capacity of 380. For more demanding separations the 250 mm long monolith provided the highest peak capacity in the shortest possible time frame.     

Sensitive biomonitoring of phthalate metabolites in human urine using packed capillary column switching liquid chromatography coupled to electrospray ionization ion-trap mass spectrometry

A rapid and sensitive method for the determination of the phthalate monoesters monoethyl phthalate (MEP), monobutyl phthalate (MBP), monobenzyl phthalate (MBzP) and monoethylhexyl phthalate (MEHP), in human urine, using packed capillary column liquid chromatography coupled to electrospray quadrupole-ion trap mass spectrometry (ESI-QITMSⁿ) has been developed. Sample volumes of 200 L of deconjugated and diluted urine were loaded onto a precolumn of 30 mm×0.32 mm I.D. packed with Hypercarb 5 m particles, using a sample carrier consisting of acetonitrile/water (15/85, v/v, adjusted to pH 2 using HCl) with a flow rate of 20 L/min. Backflushed elution onto a 100 mm×0.32 mm I.D. analytical column packed with 5 m Hypercarb particles was conducted using a tetrahydrofuran/water gradient where both solvents contained 10 mM ammonium acetate, at a flow rate of 4 L/min. Determination of the monophthalates was achieved within 8 min. Ionization was performed in the negative mode and the analytes were observed as [M-H]^– at m/z=193.1, 221.1, 255.1 and 277.0 for MEP, MBP, MBzP and MEHP, respectively. Quantification was performed in the multiple reaction monitoring (MRM) mode monitoring the fragments at m/z=121.1, 177.0, 183.0 and 233.0 for MEP, MBP, MBzP and MEHP, respectively. The method was validated over the concentration range 2.5–125 ng/mL in pretreated urine samples, corresponding to 25–1250 ng/mL untreated urine, yielding correlation coefficients in the range 0.996–0.999. The within-assay (n=6) and between-assay (n=6) repeatabilities were in the range 4.0–18% and 4.8–15% RSD, respectively. The mass limits of detection were in the range 32–70 pg, corresponding to concentration limits of detection of 1.6–3.5 ng/mL of untreated urine.     

Practical aspects of fast reversed-phase high-performance liquid chromatography using 3 microm particle packed columns and monolithic columns in pharmaceutical development and production working under current good manufacturing practice

The potential and limitations of fast reversed-phase high-performance liquid chromatographic separations for assay and purity of drug substances and drug products were investigated in the pharmaceutical industry working under current good manufacturing practice using particle packed columns and monolithic columns. On particle packed columns, the pressure limitation of commercially available HPLC systems was found to be the limiting factor for fast separations. On 3 microm particle packed columns, HPLC run times (run to run) for assay and purity of pharmaceutical products of 20 min could be achieved. As an interesting alternative, monolithic columns were investigated. Monolithic columns can be operated at much higher flow rates, thus allowing for much shorter run times compared to particle packed columns. Compared to particle packed columns, the analysis time could be reduced by a factor up to 6. However, some compounds investigated showed a dramatic loss of efficiency at higher flow rates. This phenomenon was observed for some larger molecules supporting the theory that mass transfer is critical for applications on monolithic columns. At flow rates above 3 ml/min some HPLC instruments showed a dramatic increase in noise, making quantifications at low levels impossible. For very fast separations on monolithic columns, the maximum data acquisition rate of the detector is the limiting factor.     

On-line solid-phase extraction and high performance liquid chromatography determination of polycyclic aromatic hydrocarbons in water using polytetrafluoroethylene capillary

Naphthalene, biphenyl, acenaphtene, anthracene and pyrene were extracted from water samples using inner walls of polytetrafluoroethylene capillary. Optimum conditions for sorption, desorption and heart-cutting of the analyte zone were found. Combined on-line solid-phase extraction and HPLC method for determination of these compounds was proposed. Limits of detection were: (μg L⁻¹): 0.4 (naphthalene), 0.3 (biphenyl), 0.6 (acenaphtene), 0.2 (anthracene) and 0.1 (pyrene).     

Poly (methacrylic acid-ethylene glycol dimethacrylate) monolithic capillary for in-tube solid phase microextraction coupled to high performance liquid chromatography and its application to determination of basic drugs in human serum

A poly (methacrylic acid-ethylene glycol dimethacrylate) monolithic capillary column was prepared for in-tube solid-phase microextraction. Comparing with the commonly used open tubular extraction capillary, which cannot provide sufficient extraction efficiency since the ratio of its coating volume to that of the capillary void volume is relatively small, the monolithic column with greater phase ratio combined with convective mass transfer provides the possibility to improve the extraction efficiency with shorter capillary. As to poly (methacrylic acid-ethylene glycol dimethacrylate), its hydrophobic main chains and acidic pendant groups make it a superior material for extraction of basic analytes from aqueous matrix.An on-line monolithic capillary column solid phase microextraction (SPME) method was developed for determination of theobromine, theophylline and caffeine in serum samples. The high extraction efficiency was obtained for all the three analytes, yielding the detection limits of 12, 8 and 6.5 ng/mL by UV detection, respectively. Excellent method reproducibility (R.S.D. < 2.9%) was found over a linear dynamic range of 0.05-2 μg/mL in serum sample. The monolithic capillary column was proved to be reusable in coping with serum samples, which would facilitate practical determination of basic drugs.     

Quantitation of hindered amine light stabilizers in plastic materials by high performance liquid chromatography and mass spectrometric detection using electrospray ionization and atmospheric pressure photoionization

In this work new high performance liquid chromatographic methods in combination with mass spectrometry have been developed for the quantitation of hindered amine light stabilizers (HALS) which are commonly used as monomeric and oligomeric species for stabilization of plastic materials. These analytes are difficult to separate under traditional reversed phase conditions. In the present study new silica-based pH stable reversed phases that had become available recently were investigated for HALS analysis, and turned out to be well suited employing mobile phases at a pH of around 11 adjusted by addition of ammonia. Detection was done by mass spectrometry employing both time-of-flight and triple quadrupole mass analyzers. The performance of electrospray ionization (ESI) as well as atmospheric pressure photoionization (APPI) was investigated and compared. Despite the high pH of the mobile phase, an excellent ionization could be obtained in the positive ion mode. ESI provided slightly lower limits of quantitation (on average a factor of 2) in comparison with APPI. The method allowed the quantitation of a range of different HALS down to 0.05–0.005% (depending on the HALS) in polymeric materials. Sample preparation consisted in dissolving the sample in toluene and precipitation of the polymer with acetone. The procedure can be routinely applied to aging tests of plastic materials in order to predict the lifetime of plastic components.