晶种协同廉价有机模板导向合成高纯度MCM-49沸石

采用廉价低毒性的环己胺（CHA）作为有机模板剂,并合理添加少量MCM-49沸石晶种,在静态水热条件下成功合成了高纯度MCM-49沸石.研究了起始凝胶组成（如Al₂O₃/SiO₂,H₂O/SiO₂,CHA/SiO₂,晶种/SiO₂,Na₂O/SiO₂）、晶化温度和时间等因素对合成MCM-49沸石的影响.通过XRD、SEM、N₂吸附、固体²⁷Al和²⁹Si MAS NMR等手段表征产物,结果表明合成的MCM-49沸石具有良好的结晶度、均匀的晶体尺寸、高比表面积和纯的四配位Al³⁺物种.热重差热分析（TG-DTA）和固体¹³C MAS NMR表征结果证实CHA是作为模板剂填充在沸石产物的孔道内.这种合成MCM-49的方法具有廉价和低毒性的特点,对其产业应用有潜在的重要价值.     

间歇式水热合成制备丝光沸石膜及其异丙醇脱水应用

采用市售廉价大孔α-Al₂O₃管作为基质材料，通过热浸渍法在管外表面涂敷晶种，随后在无模板剂体系下，利用新型的间歇式水热合成法制备丝光沸石膜。对比了传统加热和间歇式加热对丝光沸石膜形貌、结构及渗透蒸发异丙醇脱水分离性能的差异。考察了合成液中Na₂O/SiO₂、SiO₂/Al₂O₃和NaF/SiO₂物质的量之比在间歇式水热合成下对丝光沸石膜的影响。研究结果表明，当合成液中Na₂O/SiO₂、SiO₂/Al₂O₃和NaF/SiO₂物质的量之比分别为0.24、16.7和0.25时，制备的丝光沸石膜渗透蒸发异丙醇脱水分离性能最佳，在75℃下，对异丙醇/水(9∶1，w/w)的渗透通量达5.60 kg·m^-2·h^-1，水对异丙醇的分离因数大于10 000。     

变浓度无有机模板剂合成ZSM-5沸石分子筛膜

报道了无有机模板剂制备出15 nm的ZSM-5分子筛，并以其为晶种浸涂在多孔α-Al₂O₃陶瓷管外表面，再用先浓后稀的无有机模板剂的晶化液水热合成出ZSM-5分子筛膜的新方法。晶种和晶化液的物质的量组成为12Na₂O∶100SiO₂∶2Al₂O₃∶(2 500～5 000)H₂O。XRD分析表明α-Al₂O₃陶     

磁性核P型沸石的合成及表征

为了解决实际应用中微细粉末状沸石产品与所处理溶液难以分离的问题，采用水热法进行磁性P型沸石的制备研究。按照传统P型沸石制备的方法，配制Na₂O∶Al₂O₃∶SiO₂∶H₂O物质的量的比为3∶1∶2.3∶185料液，室温下先搅拌老化反应3 h，然后加入磁性Fe₃O₄在95 ℃下静态晶化6 h，合成了一系列包覆Fe₃O₄的磁性核P型沸石。通过晶化过程中对固相进行XRD、SEM、IR及能谱表征等分析，及对液相组成含量进行测定，探讨了磁性核P型沸石的形成机理。合成的磁性核P型沸石显示良好超顺磁特性，并具有很好的磁稳定性，其磁化率随所包覆Fe₃O₄量的增加而增大，钙、镁离子离子交换吸附性能随包覆Fe₃O₄量的增加而有小幅下降，但是仍保持了较高的值。四氧化三铁质量含量为0.176 3%的磁性P型沸石，其钙镁离子的交换吸附量分别为315.6 mg CaCO₃·g^-1 和86.94 mg MgCO₃·g^-1。     

清液体系中T型分子筛膜的高重复性合成与渗透汽化性能

以自制微米级分子筛为晶种,在清液体系中成功合成出高性能的T型分子筛膜,考察了硅铝比、水硅比、碱度及合成温度与时间等条件对膜的生长和渗透汽化性能的影响.结果表明,在摩尔组成为1SiO₂:0.015Al₂O₃:0.41(Na₂O+K₂O):30H₂O的清液体系中,于423K晶化6h的条件下可较快地形成一层厚度为5μm的连续致密纯相T型分子筛膜,较大缩短了膜合成时间且提高了膜致密性.在优化条件下所合成的膜具有优良的分离性能和高重复性.348K时,在10wt%水-90wt%异丙醇混合物体系中膜的渗透通量和分离因子分别高达4.20kg/(m²·h)和7800.     

利用Taguchi法以高岭土为原料制备高硅NaY分子筛

采用Taguchi试验方法优化出了以高岭土为原料制备高硅NaY分子筛的最佳合成参数,考察了硅溶胶的加入量、反应体系的碱度、加水量以及晶化时间对NaY分子筛硅铝比和结晶度的影响。结果表明,高硅NaY分子筛的最佳合成条件是：反应体系各组分的物质的量比为7.5SiO₂∶1.0Al₂O₃∶2.2Na₂O∶120H₂O,晶化时间为16 h。同时发现,对合成样品性能的影响最为显著的因素是硅溶胶的加入量和碱度。采用X射线衍射、N₂静态容量吸附法和扫描电镜对利用最佳条件所合成样品的硅铝比、比表面积、孔分布以及表观形貌进行了表征。结果显示,以高岭土原料制备的NaY分子筛比参考样品拥有更高的硅铝比和更大的比表面积。     

WQD-1沸石离子交换性能的研究

测定了W_QD-1沸石在一价碱金属离子混合溶液中的分配系数、饱和交换量和在25℃时，NH⁺₄/K⁺、NH⁺₄/Na⁺交换等温线。得出该沸石一价离子选择性序列为：Cs⁺>Rb⁺>K⁺>Na⁺>Li⁺, Na⁺/K⁺交换自由焓变ΔG(T,P)=-6.745 KJ/mol。     

Na+，K+//Br-，SO42--H2O四元体系323 K相平衡研究

采用等温溶解平衡法研究了四元体系Na⁺,K⁺//Br^-,SO₄^2--H₂O在323 K的相平衡关系,测定了该体系323 K的溶解度及平衡液相的密度,绘制了该体系的相图。研究发现：平衡体系存在复盐钾芒硝Na₂SO₄·3K₂SO₄的结晶区。其相图由3个共饱和点,7条单变量曲线和5个结晶区组成。相区分别对应NaBr·2H₂O、Na₂SO₄、K₂SO₄、KBr和Na₂SO₄·3K₂SO₄结晶区。其中复盐钾芒硝Na₂SO₄·3K₂SO₄,Na₂SO₄和K₂SO₄有较大结晶区,而NaBr·2H₂O和KBr有较小结晶区。对比了等温条件下四元体系Na⁺,K⁺//Cl^-,SO₄^2--H₂O相平衡结果。实验结果表明溴化物对硫酸盐有较强盐析作用。     

α-Fe2O3/SiO2纳米颗粒混合体系表面的酸碱性质及其对重金属离子的吸附行为

以Fe(NO₃)₃·9H₂O和正硅酸乙酯(TEOS)为原料, 通过溶胶-凝胶法和辅助模板法分别制备了纳米α-Fe₂O₃和SiO₂, 并对所合成样品进行了粉末X射线衍射(XRD)和BET表征. 使用自动电位滴定仪测定了α-Fe₂O₃/SiO₂纳米颗粒混合体系的表面酸碱性质. 研究了在不同pH下α-Fe₂O₃/SiO₂混合体系对Cu²⁺、Pb²⁺、Zn²⁺离子的吸附行为. 基于上述实验数据, 用WinSGW软件计算了α-Fe₂O₃/SiO₂混合体系表面酸碱配位常数, 并得出结论: α-Fe₂O₃/SiO₂混合体系表面反应为单一脱质子反应≡XOH ⇔ ≡XO^-+ H⁺(lg K = -8.19±0.15), 明显区别于同时具有加质子和脱质子反应的α-Fe₂O₃/SiO₂/γ-Al₂O₃, α-Fe₂O₃/γ-Al₂O₃和SiO₂/γ-Al₂O₃等纳米颗粒混合体系. 在此基础上拟合得到α-Fe₂O₃/SiO₂混合体系吸附重金属离子Cu²⁺、Pb²⁺、Zn²⁺的表面络合反应平衡常数分别为:
≡XOH + M²⁺ ⇔ ≡XOM⁺+ H⁺ [lg K = -3.1, -3.6, -3.8 (M = Cu, Pb, Zn)].
≡XOH＋M²⁺＋H₂O ⇔≡XOMOH＋2H⁺[lg K = -8.8, -8.0, -10.5 (M = Cu, Pb, Zn)]     

微波场中T型分子筛的合成及晶化研究

研究了微波场中T型分子筛的结晶过程。考察了微波加热体系中合成参数如合成时间、溶胶组成、反应压力和模板剂用量对分子筛晶化的影响。微波加热的主要优点是减少合成时间,无模板剂的溶胶在普通加热条件下的晶化时间需要120 h,而在微波场中则仅需要20～25 h。另一方面,由于微波的快速加热特性促进了稳定相钙十字沸石的生成,从而减小了次稳定相T型分子筛的结晶区间。在未添加模板剂条件时,100 ℃下微波水热合成T型分子筛的结晶区间为：20≤n_SiO2/n_Al2O3≤22和0.31≤ n_M2O/n_SiO2≤0.33(其中M₂O=Na₂O+K₂O, n_Na/n_K=3和n_M2O/n_SiO2=11.70)。在普通加热和微波加热合成体系中,添加模板剂均能扩大结晶区间,同时还可以进一步减少合成时间。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.