Determination of trace heavy metals in waters by flame atomic absorption spectrometry after preconcentration with 2,4-dinitrophenyldiazoaminoazobenzene on Amberlite XAD-2

A new column, solid-phase extraction (SPE), preconcentration method was developed for determination of Cd, Co, and Cu ions in natural water samples by flame atomic absorption spectrometry. The procedure is based on the retention of analytes in the form of 2,4-dinitrophenyldiazoaminoazobenzene (DNDAA) complex on a mini column of DNDAA-XAD-2 resin. The effects of pH, eluent type, eluent concentration, eluent volume, resin quantity, sample volume, sample flow rate, and matrix ions (Na, Ca, and Mg) were investigated on the recovery of the metals using model solutions. The detection limit for Cd, Co, and Cu was 0.062, 0.084, and 0.057 μg L⁻¹ and the quantification limit was 0.17, 0.24, and 0.12 μg L⁻¹ respectively. The method was validated by the analysis of a certified reference material with the results being in agreement with those quoted by manufactures. The developed method was applied to the determination of trace metal ions in tap water, river water samples with satisfactory results.     

Preconcentration and Determination of Copper(II) by Novel Solid-Phase Extraction and High-Resolution Continuum Source Flame Atomic Absorption Spectrometry

Amberlite XAD-4 modified with N-para-anisidine-3,5-di-tert-butylsalicylaldimine was investigated as a new chealting sorbent for the selective separation and preconcentration of Cu(II). The metal ion was retained by chemical sorption on the modified resin, eluted by hydrochloric acid, and determined by high-resolution continuum source flame atomic absorption spectrometry. The prepared resin was characterized for the solid-phase extraction of Cd²⁺, Co²⁺, Cr³⁺, Cu²⁺, Fe³⁺, Mn²⁺, Ni²⁺, Pb²⁺, and Zn²⁺ in a column. The influence of the pH, the mass of solid phase, eluent, flow rate, and sample volume was optimized. Using the optimum conditions, only Cu(II) showed quantitative sorption at the 95% confidence level, and the recoveries of the other metal ions were below 80%. A preconcentration factor 125 was obtained for Cu(II) with a limit of detection of 0.56?µg?L^?1. The method was used for the determination of Cu(II) in tap water, river water, tomato leaves, and fish. The relative standard deviation and the relative error were lower than 7%.     

Pyrogallol Immobilized Amberlite XAD-2: A Newly Designed Collector for Enrichment of Metal Ions Prior to their Determination by Flame Atomic Absorption Spectrometry

 Pyrogallol is covalently linked with the benzene ring of Amberlite XAD-2, through an azo (–N=N–) spacer group and the resulting new polymer characterized by elemental analyses, thermogravimetric analysis (TGA) and infrared (IR) spectra. It has been used for separation and preconcentration of Cu(II), Cd(II), Co(II), Ni(II), Pb(II), Zn(II), Mn(II), Fe(III) and U(VI) prior to their determination by flame atomic absorption spectrometry (FAAS) or fluorimetry (for U(VI) only). The pH ranges for quantitative sorption are 5.5–6.5, 5.5–7.5, 5.5–7.0, 5.5–7.0, 5.5–6.5, 5.5–6.5, 5.5–8.0, 5.5–6.2 and 5.5–6.2, respectively, for the nine metal ions, which can be desorbed (recovery 90–99%) with 4 mol L⁻¹ HNO₃ or HCl. The sorption capacity of the resin has been found to be in the range 4.10 to 6.71 mg of metal g⁻¹ of dry resin. The loading half time (t_1/2) was ≤3.3 min for all the metal ions. The effects of NaF, NaCl, NaNO₃, Na₂SO₄, and Na₃PO₄ on the sorption of these metal ions (0.2 μg mL⁻¹) are reported. The Ca(II) and Mg(II) are tolerable up to a concentration level of 40–400 and 25–240 μg mL⁻¹, respectively. The enrichment factor for Cu(II), Cd(II), Co(II), Ni(II), Pb(II), Zn(II), Mn(II), Fe(III) and U(VI) has been found to be 65, 40, 65, 120, 25, 160, 120, 140, and 70 (concentration level 2–25 ng mL⁻¹), respectively. The limit of detection for these nine metal ions is 5.0, 1.3, 5.0, 4.0, 25.0, 0.5, 1.0, 2.0 and 1.0 ng mL⁻¹, respectively. After enrichment on the present matrix, the flame AAS method has been applied to determine these metal ions (except U) in river water samples (RSD ≤ 7%) and well water (RSD ≤ 8%). Uranium present in well water samples has been enriched on the present matrix and determined by a fluorimetric method (RSD ≤ 6%). The cobalt present in pharmaceutical vitamin tablets was also preconcentrated with the aid of the present chelating resin and determined by FAAS to be 1.93 μg g⁻¹ (RSD ∼4%). Received May 16, 2000. Revision April 3, 2001.     

磁性石墨烯固相萃取/原子吸收法测定环境水样中的痕量铜

以1-(2-吡咯偶氮)-2-萘酚(PAN)为络合剂络合水样中的痕量铜,以磁性石墨烯(G)纳米材料为固相萃取吸附剂,建立了测定水样中痕量铜的磁性固相萃取/火焰原子吸收分光光度法。此方法将磁性石墨烯比表面积大、吸附性能好的优点与Fe3O4纳米粒子的磁性相结合,采用的磁性固相萃取避免了传统固相萃取中离心和过滤等繁琐的操作步骤。对影响G-Fe3O4萃取效率的实验因素进行了优化。在优化实验条件下,对铜离子的富集倍数为80.4倍,线性范围为0.5～100μg/L,相关系数(r)为0.998 1,检出限为0.067μg/L,相对标准偏差为2.1%～5.2%。此方法成功地应用于矿泉水、自来水、公园湖水中铜离子含量的测定,其加标回收率为94%～103%。结果表明,该磁性石墨烯纳米材料G-Fe3O4对水样品中铜的PAN络合物具有较高的富集能力。     

Solid-Phase Extraction of Copper with Cupron on Octadecyl Silica Cartridge and its Determination with Atomic Absorption Spectrometry

Solid-phase extraction of trace amounts of copper from large volumes of aqueous solutions was studied. The extraction was carried out by means of an octadecyl silica cartridge modified with cupron. The effect of different parameters such as sample matrix, flowrates of sample solution and eluent, pH, breakthrough volume, and potentially interfering ions was examined. Cu²⁺ was extracted from solution in the pH range of 6–8.5 on a modified cartridge. Elution was accomplished using 2mL of 0.2M HNO₃. Hence, with a typical preconcentration factor of 1000, a detection limit of 0.02ngmL^–1 was obtained. The method was applied to the determination of copper in natural water samples.     

浊点萃取-火焰原子吸收光谱法测定样品中的痕量钴

研究了基于表面活性剂Triton X-114和络合剂吡咯烷二硫代氨基甲酸铵（APDC）浊点萃取钴的样品前处理方法.优化了浊点萃取条件参数,包括pH值、Triton X-114用量、APDC浓度、平衡温度及时间等,建立了浊点萃取-火焰原子吸收光谱法测定痕量钴的方法.该法的检测限（3σ）为2.6μg/L,相对标准偏差RSD为6.2%（n=7,c=200μg/L）.该法成功地应用于海带、维生素B12注射液等样品中钴的测定.     

Determination of Iron(III), Cobalt(II) and Chromium(III) in Various Water Samples by Flame Atomic Absorption Spectrometry After Preconcentration by Means of Saccharomyces Carlsbergensis Immobilized on Amberlite XAD-4

A method for the determination of Fe(III), Co(II) and Cr(III) by flame atomic absorption spectrophotometry (FAAS) after preconcentrating on a column containing S. carlsbergensis immobilized on Amberlite XAD-4 has been developed. The optimum values of pH, amount of adsorbent, elution solution and flow rate of the sample solution were determined for the quantitative recovery of the analytes. The effect of interfering ions on the recovery of the analytes was also investigated. Under the optimum conditions, recoveries of Fe(III), Co(II) and Cr(III) by S. carlsbergensis immobilized on Amberlite XAD-4 were 99±2, 100±2 and 98±2% at 95% confidence level, respectively. The limit of detections for Fe(III), Co(II) and Cr(III) were 2.8, 3.9 and 7.4ngmL^–1, respectively. The proposed method was applied to the determination of the analytes in various water samples. The validity of the method was checked with spiked water samples. Fe(III), Co(II) and Cr(III) was determined with a relative error of less than 5%.     

火焰原子吸收光谱法测定铼产品中的痕量钠

建立了火焰原子吸收光谱法测定高铼酸、高铼酸铵、铼粉中痕量钠的方法,对样品的预处理和测定钠的条件进行了研究。结果表明:水溶解法、硝酸溶解法或硝酸-硫酸溶解法溶解样品完全,测得钠的结果吻合;于选定条件下,钠的测定浓度在0.020 0~0.500 0μg/mL范围内线性良好;测定高铼酸、高铼酸铵和铼粉样品中0.27~0.47mg/L、0.000047%~0.00048%和0.000040%~0.00049%的钠含量,检出限、相对标准偏差(RSD,n=7)、加标回收率分别为高铼酸3×10-4μg/mL、6%~10%、98%~102%,高铼酸铵3×10-4μg/mL、8%~9%、96%~102%和铼粉3×10-4μg/mL、5%~9%、96%~103%。方法结果准确、分析快速、操作简便,应用于实际的样品分析,结果满意。     

键合4-(2-吡啶偶氮)-间苯二酚螯合树脂分离富集-火焰原子吸收法测定蔬菜中痕量镉(Ⅱ)

本文合成了Amberlite XAD-4键合4-(2-吡啶偶氮)-间苯二酚螯合树脂,并考察了其对痕量镉(Ⅱ)的吸附性能。探讨了溶液pH、洗脱剂和干扰离子等对镉(Ⅱ)分离富集的影响。树脂吸附容量为4.7mg/g,吸附的镉(Ⅱ)用5mL 2mol/L HNO3乙醇溶液洗脱,火焰原子吸收法测定。在最佳实验条件下,回收率为94.4%～97.9%,相对标准偏差在1.7%～2.7%之间。方法可用于蔬菜中镉(Ⅱ)的测定。     

Speciation Analysis of Antimony (III) and Antimony (V) by Flame Atomic Absorption Spectrometry After Separation/Preconcentration With Cloud Point Extraction

A sensitive and simple method for flame atomic absorption spectrometry (FAAS) determination of antimony species after separation/preconcentration by cloud point extraction (CPE) has been developed. When the system temperature is higher than the cloud point extraction temperature, the complex of antimony (III) with N-benzoyl-N-phenyhydroxylamine (BPHA) can enter the surfactant-rich phase, whereas the antimony (V) remains in the aqueous phase. Antimony (III) in surfactant-rich phase was analyzed by FAAS and antimony (V) was calculated by subtracting of antimony (III) from the total antimony after reducing antimony (V) to antimony (III) by L-cysteine. The main factors affecting the cloud point extraction, such as pH, concentration of BPHA and Triton X-114, equilibration temperature and time, were investigated systematically. Under optimized conditions, the detection limits (3σ) were 1.82 ng mL⁻¹ for Sb(III) and 2.08 ng mL⁻¹ for Sb(total), and the relative standard deviations (RSDs) were 2.6% for Sb(III) and 2.2% for Sb(total). The proposed method was applied to the speciation of antimony species in artificial seawater and wastewater, and recoveries in the range of 95.3–106% were obtained by spiking real samples. This technique was validated by means of reference water materials and gave good agreement with certified values.     

火焰原子吸收分光光度法测大沂河水体的重金属含量

采用火焰原子吸收分光光度法测定了山东省曲阜市大沂河水体的重金属铜、铅、镉、锌含量。结果表明,大沂河水体中铜、铅、镉、锌的最高含量分别为0.018,0.230,0.176,0.490mg/L,其中铅和镉的含量超过国家Ⅴ类水标准。     

流动注射-火焰原子吸收光度法测定矿泉水中的锶

用流动注射离子交换系统于酸性条件下在线富集饮用天然矿泉水中的锶,火焰原子吸收光度法测定,共存成分无干扰,方法简便快速,富集倍数可随意调节。在 60 h～(-1)的进样频率下,灵敏度提高 17倍。用于矿泉水中锶的测定,当含量为 60～250 ng/ml时,相对标准偏差为 0.68％～0.94％。回收率为 94.4％～110.3％,检测限为 15ng/ml。     

Determination of Manganese(II) with Preconcentration on Almond Skin and Determination by Flame Atomic Absorption Spectrometry

Almond skin was used as a biosorbent by solid-phase extraction for the preconcentration of manganese(II) before the determination by flame atomic absorption spectrometry. Characterization of almond skin was performed by infrared spectroscopy. The functional groups of the almond skin surface were shown to be beneficial for the adsorption of manganese(II). At pH 6.0, the manganese(II) ions were retained on the almond skin and afterward quantitatively eluted using 1.5?mol?L^?1 nitric acid. The pH, flow rate and volume of sample, concentration, and flow rate of eluent and interfering ions were characterized. Using a sample size of 30?mL, a linear dynamic range of 1–120?µg?L^?1 was obtained. A detection limit of 0.24?µg?L^?1 manganese(II) and a relative standard deviation of 1.6% at 30?µg?L^?1 were achieved. The accuracy of the present procedure was evaluated by the determination of manganese(II) in a certified reference material (GSB07-1189-2000). The protocol was also used for the determination of manganese(II) in wastewater. The fortified recoveries were from 99.0 to 99.4%.     

流动注射在线萃取色谱预浓集火焰原子吸收法测定钯

以三异辛胺萃淋树脂为微型柱固定相，采用流动注射在线预浓集与火焰原子吸收法联用技术，对微量钯的测定进行了研究。在0.5mol/L的HCl介质中以7.8mL/min的速率采样90s再用0.1mol/L硫脲－0.5mol/L HCl洗脱；在27h^-1的采样频率下，浓集系数为50倍，浓集效率为22.5min，消耗指数0.23mL。线性范围为0－1000μg/L，检出限为0.34μg/L。钯含量水平50μg/L时，连续11次测定的相对标准偏差为2.6%，并对加氢催化剂中的钯进行了加标回收率实验，回收率为99.3%-101.2%。     

磁性纳米材料固相萃取/火焰原子吸收光谱法测定环境水样中的痕量银离子

在纳米四氧化三铁表面包覆二氧化硅,并以十八烷基三甲氧基硅烷进行化学修饰,用作固相萃取吸附剂富集环境水样中的痕量银离子,用火焰原子吸收光谱法测定,建立了一种灵敏、快速、简便分析银离子的新方法。考察了水样pH值、吸附剂用量、螯合剂用量、振荡时间、洗脱剂、共存离子等对银离子回收率的影响。实验结果表明,对于200 mL水样,在pH 7.0、吸附剂用量为0.1 g、螯合剂5-Br-PADAP(0.5 g/L)用量为0.6 mL、吸附时间为10 min的条件下,材料对Ag+具有较好的吸附性,且用6 mL 1.0 mol/L的硝酸可完全洗脱所吸附的Ag+。在优化实验条件下,检出限(3σ)为0.15μg/L,相对标准偏差(10μg/L,n=6)为1.4%,富集因子达31。分别对河水、湖水样品中Ag+进行检测,加标回收率为85.0%~94.8%。     

原子捕集火焰原子吸收法测定水中镉

采用自制原子捕集装置，选择了镉在不锈钢管上捕集的合适条件，使测镉的灵敏度比常规火焰原子吸收法提高了116倍。应用于工业废水中痕量镉的测定，获得满意结果。     

Preconcentration and Determination of Trace Amounts of Heavy Metals in Water Samples Using Membrane Disk and Flame Atomic Absorption Spectrometry

A fast and simple method for preconcentration of Ni^2＋, Cd^2＋, Pb^2＋, Zn^2＋, Cu^2＋ and Co^2＋ from natural water samples was developed. The metal ions were complexed with sodium diethyldithiocarbamate （Na-DDTC）, then adsorbed onto octadecyl silica membrane disk, recovered and determined by FAAS. Extraction efficiency, influence of sample volume and eluent flow rates, effects of pH, amount of Na-DDTC, nature and amount of eluent for elution of metal ions from membrane disk, break through volume and limit of detection have been evaluated. The effect of foreign ions on the percent recovery of heavy metal ions has also been studied. The limit of detection of the proposed method for Ni^2＋, Cd^2＋, Pb^2＋, Zn^2＋, Cu^2＋ and Co^2＋was found to be 2.03, 0.47, 3.13, 0.44, 1.24 and 2.05 ng·mL^-1, respectively. The proposed （DDTC） method has been successfully applied to the recovery and determination of heavy metal ions in different water samples.     

流动注射在线液-液萃取火焰原子吸收法测定水中痕量铅

提出了一种流动注射在线液－液萃取火焰原子吸收直接测定水中痕量铅的分析方法。实验以APDC为螯合剂,用MIBK为萃取剂,研究了在线萃取中各种实验参数、酸度条件的影响,考察了共存元素的干扰。方法的RSD（n=12)为2．7％,测定检出限为3．1μg/L,回收率为96％－106％。     

火焰原子吸收光谱法测定莲子中的微量元素

莲子经过硝酸、高氯酸处理后，用火焰原子吸收光谱法测定了莲子中的镁、铁、锰、锌、铜、钴、钾、钙等金属元素含量。此法快速、简单，结果准确。     

碘化钾―甲基异丁基甲酮萃取―火焰原子吸收法测定土壤中的痕量铅

土壤样品经微波消解,在优化的条件下,用碘化钾―甲基异丁基甲酮萃取,采用火焰原子吸收光谱法测定其中的铅。结果表明,在盐酸质量分数为1%～2%,萃取时间为2 min,平衡时间为15 min,样品中的铅能被定量萃取。方法检出限为0.1 mg/kg。方法用于土壤标准样品测定,测定值与标准值相符,相对标准偏差为1.2%～1.4%,相对误差为0.8%～2.5%。实际土壤样品的测定结果显示,回收率为99.8%～100.4%。