Preparation and Characterization of Single-Phase Perovskite La0.6Sr0.4Co0.8Fe0.2O3-δ

Single-phase perovskite La0.6Sr0.4Co0.8Fe0.2O3-δ has been successfully prepared by using citrate-EDTA complexation method at relatively low calcination temperature. The structure and thermal decomposition process of the complex precursor have been investigated by means of differential scanning calorimetry-thermal gravimetric analysis (DSC/TGA), X-ray diffraction (XRD), and Fourier transform infrared spectroscopic (FT-IR) measurements. The precursor decomposed completely and started to form perovskite-type oxide above 420℃ according to the differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) results. Single-phase perovskite La0.6Sr0.4Co0.8Fe0.2O3-δ obtained has been confirmed from the XRD pattern, and no peak of SrCO3 was found by XR.D of the oxides synthesized at a relatively low temperature of 800 ℃. The reducibility of La0.6Sr0.4Co0.8Fe0.2O3-δ was also characterized by the temperature programmed reduction (TPR) technique. Disk shaped dense La0.6Sr0.4Co0.8Fe0.2O3-δ membrane was prepared by the isostatical pressing method. The oxygen flux rate of dense La0.6Sr0.4Co0.8Fe0.2O3-δ membrane was (2.8-18)×10-8 mol/(cm2·s) in the temperature range of 800-1 000℃.     

La0.8Sr0.2Fe1-xScxO3-δ催化剂的制备、表征及甲烷催化燃烧性能

采用甘氨酸-硝酸盐溶液燃烧法制备了钙钛矿型氧化物催化剂La_0.8Sr_0.2Fe_1-xSc_xO_3-δ (LSFS, x=0, 0.3,0.4, 0.5, 0.6, 0.8, 1), 利用X射线衍射(XRD)、H₂程序升温还原(H₂-TPR)、扫描电子显微镜(SEM)和比表面积测试等手段对催化剂进行了系统表征, 并在常压微型固定床反应器上考察了催化剂对甲烷燃烧的催化性能. 结果表明, 经空气气氛下900 °C煅烧5 h制备的LSFS均具有单一的钙钛矿结构, 在La_0.8Sr_0.2FeO_3-δ (LSF)中掺杂Sc有助于改善催化剂的抗烧结性能, 提高催化剂的比表面积. 当LSF 中的Sc 掺杂量为0.4-0.6 时, 所形成的LSFS表现出良好的甲烷催化燃烧活性, 其中Sc 掺杂量为0.5 时, 其起燃温度(T₁₀)和完全转化温度(T₉₀)分别为406和563 °C, 与La_0.8Sr_0.2FeO_3-δ和La_0.8Sr_0.2ScO_3-δ相比, T₁₀分别降低了14和87 °C; T₉₀分别降低了59和95 °C.     

Synthesis and characterization of La0.8Sr1.2Co0.5M0.5O4−δ (M=Fe, Mn)

The M⁴⁺-containing K₂NiF₄-type phases La_0.8Sr_1.2Co_0.5Fe_0.5O₄ and La_0.8Sr_1.2Co_0.5Mn_0.5O₄ have been synthesized by a sol–gel procedure and characterized by X-ray powder diffraction, thermal analysis, neutron powder diffraction and Mössbauer spectroscopy. Oxide ion vacancies are created in these materials via reduction of M⁴⁺ to M³⁺ and of Co³⁺ to Co²⁺. The vacancies are confined to the equatorial planes of the K₂NiF₄-type structure. A partial reduction of Mn³⁺ to Mn²⁺ also occurs to achieve the oxygen stoichiometry in La_0.8Sr_1.2Co_0.5Mn_0.5O_3.6. La_0.8Sr_1.2Co_0.5Fe_0.5O_3.65 contains Co²⁺ and Fe³⁺ ions which interact antiferromagnetically and result in noncollinear magnetic order consistent with the tetragonal symmetry. Competing ferromagnetic and antiferromagnetic interactions in La_0.8Sr_1.2Co_0.5Fe_0.5O₄, La_0.8Sr_1.2Co_0.5Mn_0.5O₄ and La_0.8Sr_1.2Co_0.5Mn_0.5O_3.6 induce spin glass properties in these phases.     

中温固体氧化物燃料电池La1.6Sr0.4Ni1-xCuxO4阴极材料的制备及电化学性能

采用甘氨酸-硝酸盐法合成了中温固体氧化物燃料电池阴极材料La_1.6Sr_0.4Ni_1-xCu_xO₄ (x=0.2, 0.4, 0.6,0.8), 利用X射线衍射(XRD)和扫描电子显微镜(SEM)对其结构和微观形貌进行了表征. 结果表明, 该阴极材料与固体电解质Ce_0.9Gd_0.1O_1.95(CGO)在1000 °C烧结时不发生化学反应, 且烧结4 h 后, 二者之间可形成良好的接触界面. 利用电化学交流阻抗谱技术对阴极材料的电化学性能进行研究, 结果显示, 当Cu离子掺杂量(x)为0.6 时, La_1.6Sr_0.4Ni_0.4Cu_0.6O₄阴极具有最小的极化电阻, 在空气中当测试温度为750 °C时, 极化电阻为0.35 Ω·cm². 在不同氧分压条件下电化学阻抗谱分析结果表明, 电极上的两个氧还原反应主要包含氧离子从三相界面向电解质CGO 转移的过程和电荷的迁移过程, 其中电荷的迁移过程为电极反应的速率控制步骤.La_1.6Sr_0.4Ni_0.4Cu_0.6O₄电极在空气中700 °C和阴极电流密度为45 mA·cm^-2时, 阴极过电位为45 mV. 本研究的初步结果表明La_1.6Sr_0.4Ni_1-xCu_xO₄材料是一种电化学性能较为优良的新型中温固体氧化物燃料电池(IT-SOFC)阴极材料.     

钙铝石涂层对整体型钙钛矿氧化物催化剂活性和热稳定性的影响

 采用固相反应法合成了钙铝石材料 12SrO•7Al2O3, 并以此作为涂层制备了堇青石蜂窝陶瓷型 La0.8Sr0.2MnO3 整体催化剂, 在不同温度 (850~1 050 oC) 下对该催化剂进行了热处理, 并采用 N2 吸附-脱附、X 射线衍射和扫描电镜等手段对其进行了表征, 考察了其催化甲基丙烯酸甲酯燃烧反应的活性. 结果表明, 12SrO•7Al2O3 作为涂层明显改善了整体催化剂的热稳定性, 在 850 oC 下焙烧 6 h 后, 含有 12SrO•7Al2O3 涂层的整体催化剂在 260 oC 即可将甲基丙烯酸甲酯完全转化. 12SrO•7Al2O3 涂层可避免 La0.8Sr0.2MnO3 活性组分与堇青石的接触, 减轻了活性组分在催化剂表面的烧结, 有利于保持 La0.8Sr0.2MnO3 活性组分的晶体结构和分散度, 提高整体催化剂的活性和热稳定性.     

(La0.8A0.2)MnO3 (A = Sr,K) perovskite catalysts for NO and C10H22 oxidation and selective reduction of NO by C10H22

In this work, we studied the catalytic activity of LaMnO₃ and (La_0.8A_0.2)MnO₃ (A = Sr, K) perovskite catalysts for oxidation of NO and C₁₀H₂₂ and selective reduction of NO by C₁₀H₂₂. The catalytic performances of these perovskites were compared with that of a 2 wt% Pt/SiO₂ catalyst. The La site substitution increased the catalytic properties for NO or C₁₀H₂₂ oxidation compared with the non-substituted LaMnO₃ sample. For the most efficient perovskite catalyst, (La_0.8Sr_0.2)MnO₃, the results showed the presence of two temperature domains for NO adsorption: (1) a domain corresponding to weakly adsorbed NO, desorbing at temperatures lower than 270 ℃ and (2) a second domain corresponding to NO adsorbed on the surface as nitrate species, desorbing at temperatures higher than 330 ℃. For the Sr-substituted perovskite, the maximum NO₂ yield of 80% was observed in the intermediate temperature domain (around 285 ℃). In the reactant mixture of NO/C₁₀H₂₂/O₂/H₂O/He, (La_0.8Sr_0.2)MnO₃ perovskite showed better performance than the 2 wt% Pt/SiO₂ catalyst： NO₂ yields reaching 50% and 36% at 290 and 370 ℃, respectively. This activity improvement was found to be because of atomic scale interactions between the A and B active sites, Sr²⁺ cation and Mn⁴⁺/Mn³⁺ redox couple. Thus, (La_0.8Sr_0.2)MnO₃ perovskite could be an alternative free noble metal catalyst for exhaust gas after treatment.     

Perovskite-like La1−xKxMnO3 and related compounds: Solid state chemistry and the catalysis of the reduction of NO by CO and H2

The new compounds La_1?xM_xMnO₃ (0.05 ? x ? 0.4 for M = K; x = 0.2 for M = Na, Rb) have been prepared. La_1?xK_xMnO₃ (0.05 ? x ? 0.4), LaMnO_3.01, LaMnO_3.15, La_0.8Na_0.2MnO₃, and La_0.8Rb_0.2MnO₃ have been used as catalysts in the reduction of NO. La_0.8K_0.2MnO₃ has also been used in the catalytic decomposition of NO. The activity of these catalysts is related to the presence of a Mn³⁺/Mn⁴⁺ mixed valence and to the relative ease of forming oxygen vacancies in the solid. The presence of cation vacancies in LaMnO_3.15 and the substitution of La³⁺ by alkali ions in LaMnO₃ increases the catalytic activity. The reduction of NO involves both molecular and dissociative adsorption of NO.     

Magnetic properties of La0.5−xLnxSr0.5MnO3 (Ln=Pr, Nd, Gd and Y)

Magnetic and electron transport properties of four series of manganates of the composition La_0.5−xLn_xSr_0.5MnO₃ (Ln=Pr, Nd, Gd and Y) have been investigated to examine how the ferromagnetic metallic nature of the parent La compound changes over to antiferromagnetic insulating behavior, with change in Ln and x due to the associated changes in the A-site cation radius as well as the size disorder. When Ln=Pr and Nd, there is a transition from the tetragonal I4/mcm structure to the orthorhombic Immm and Imma structures at x=0.2 and 0.35, respectively. There is a gradual evolution of the properties from those of La_0.5Sr_0.5MnO₃ to those of Pr_0.5Sr_0.5MnO₃ or Nd_0.5Sr_0.5MnO₃ with increase in x. Thus, when x>0.2 and >0.35, respectively, the Pr- and Nd-substituted manganates show ferromagnetic transitions followed by antiferromagnetic transitions at low temperatures, with the ferromagnetic T_C decreasing with increasing x. The Gd and Y series of compounds are all orthorhombic and show a decrease in T_C with the increase in x, the ferromagnetism disappearing at high x. At a value of x corresponding to the A-site cation radius of Pr_0.5Sr_0.5MnO₃, the Gd and Y series of compounds exhibit ferromagnetism in the 250-300 K region and undergo an antiferromagnetic transition on cooling. The T_C−T_N gap is sensitive to the disorder arising from the size mismatch.     

固-溶法制备中温固体氧化物燃料电池高性能La0.8Sr0.2MnO3-Ba0.5Sr0.5Co0.8Fe0.2O3阴极

研究了新型固溶法合成La_0.8Sr_0.2MnO₃（LSM）包覆Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃（BSCF）复合粉体（LSM-BSCF）,并探讨了其作为中温固体氧化物燃料电池阴极材料的电化学性能。LSM-BSCF阴极结合了LSM和BSCF阴极的优点,不仅增大了三相界面,而且稳定了微观结构。当温度为600-750℃时,其极化阻抗为0.61-0.09 Ω·cm²。与溶液注入法制备的高性能电极相比,极大地提高了性能稳定性。     

Reverse micellar synthesis and properties of nanocrystalline GMR materials (LaMnO3, La0.67Sr0.33MnO3 and La0.67Ca0.33MnO3): Ramifications of size considerations

Nanoparticles of complex manganites (viz. LaMnO₃, La_0.67Sr_0.33MnO₃ and La_0.67Ca{0.33}MnO₃) have been synthesized using the reverse micellar route. These manganites are prepared at 800‡C and the monophasic nature of all the oxides has been established by powder X-ray diffraction studies. TEM studies show an average grain size of 68, 80 and 50 nm for LaMnO₃, La_0.67Sr_0.33MnO₃ and La_0.67Ca{0.33}MnO₃respectively. Ferromagnetic ordering is observed at around 250 K for LaMnO₃, 350 K for La_0.67Sr_0.33MnO₃ and 200 K for La_0.67Ca{0.33}MnO₃. These Curie temperatures correspond well with those reported for bulk materials with similar composition.     

Lumineszenz und sensibilisierte Emission der dreiwertigen Seltenen Erden in Sr3La2W2O12

By activation of the new host lattice Sr₃La₂W₂O₁₂ with the trivalent rare earth ions Nd, Eu, Ho, Er, Tm, Yb an intense emission in the visible and/or infrared region is obtained. Energy transfer from Er³⁺ to Tm³⁺ and Nd³⁺ to Yb³⁺ has been found to occur. The excitation, emission, and diffuse reflectance spectra are analyzed for Sr₃La₂W₂O₁₂: Ln³⁺ (Ln = Nd, Sm, Eu, Dy, Ho, Er, Tm, Yb).     

The Reactivity of Manganites in 18O Isotope Exchange Reactions

The effect of the structural properties and the oxidation state of Mn on the ¹⁸O isotope exchange behaviour of ternary manganites (La_1–xSr_xMnO₃, La_0.5Sr_1.5MnO₄ and SrMnO₃) has been studied. All types of ¹⁸O isotope exchange homomolecular, partially and completely heteromolecular) take place on the very active manganites with perovskite (LaMnO₃ and La_0.7Sr_0.3MnO₃) and perovskite-like (SrMnO₃) structure, but not on the less active K₂NiF₄-structure (La_0.5Sr_1.5MnO₄). The highest ¹⁸O exchange activity is observed for La_0.7Sr_0.3MnO₃, for which the completely heteromolecular ¹⁸O exchange starts to occur at 520 K, already, a T_on which is typical for excellent redox catalysts. The influence of the structural properties on the ¹⁸O exchange and oxygen diffusion behaviour of the manganites is much more pronounced than that of the Mn³⁺/Mn⁴⁺ ratio. The different reduction behaviour of the manganites with perovskite and K₂NiF₄-structure can be explained by means of the bond-valence model.This revised version was published online in November 2005 with corrections to the Cover Date.     

Reduction properties of phases in the system La0.5Sr0.5MO3 (M=Fe, Co)

Phases formed by the reduction of compounds of the type La_0.5Sr_0.5MO₃ (M=Fe, Co) have been characterized by means of temperature programmed reduction, X-ray powder diffraction, ⁵⁷Fe Mössbauer spectroscopy and Fe K-, Co K-, Sr K-, and La L_III-edge X-ray absorption spectroscopy. The results show that treatment of the material of composition La_0.5Sr_0.5FeO₃ (which contains 50% Fe⁴⁺ and 50% Fe³⁺) at 650 °C in a flowing 90% hydrogen/10% nitrogen atmosphere results in the formation of an oxygen-deficient perovskite-related phase containing only trivalent iron. Further heating in the gaseous reducing environment at 1150 °C results in the formation of the Fe³⁺-containing phase SrLaFeO₄, which has a K₂NiF₄-type structure, and metallic iron. The material of composition La_0.5Sr_0.5CoO₃ is more susceptible to reduction than the compound La_0.5Sr_0.5FeO₃ since, after heating at 520 °C in the hydrogen/nitrogen mixture, all the Co⁴⁺ and Co³⁺ are reduced to metallic cobalt with the concomitant formation of strontium- and lanthanum-oxides.     

Composite electrodes for proton conducting electrolyte of CaZr<Subscript>0.95</Subscript>Sc<Subscript>0.05</Subscript>O<Subscript>3 – δ</Subscript>

A new method of obtaining gastight ceramic based on CaZr_0.95Sc_0.05O_{3 – δ} is presented. The microstructure and electric properties of the obtained samples, same as the behavior of composite electrodes in contact with this electrolyte, are studied for application of the obtained results in the technology of formation of electrochemical devices. The design of bilayer electrodes is suggested, in which the materials tested as the functional layer were layered lanthanum nickelate La2NiO_{4 + δ} and substituted lanthanum nickelate La_1.7Ca(Sr,Ba)_0.3NiO_{4 + δ} in combination with the electrolyte components of Ce_0.8Sm_0.2O_{2 – δ} and BaCe_0.89Gd_0.1Cu_0.01O_{3 – δ}. The collector layer used was lanthanum nickelate–ferrite LaNi_0.6Fe_0.4O_{3 – δ} and manganite La_0.6Sr_0.4MnO_{3 – δ} that are characterized by high electron conductivity, low layer resistance and are close by their values of coefficient of linear thermal expansion to the materials of functional layers. Electrochemical activity of the obtained electrodes are compared with the characteristics of composite electrodes based on lanthanum ferrite–cobaltite La_0.6Sr_0.4Fe_0.8Co_0.2O_{3 – δ} and deficient lanthanum manganite La_0.75Sr_0.2MnO_{3 – δ}.     

The nature of the orthorhombic to tetragonal phase transition in Sr1−xCaxMnO3

The orthorhombic-tetragonal phase transition in the perovskite series Sr_1−xCa_xMnO₃ 0.4?x?0.6 has been studied by synchrotron X-ray powder diffraction. At room temperature the Ca rich oxides x?0.45 have the orthorhombic Pbnm superstructure whereas Sr_0.6Ca_0.4MnO₃ is two phases with both tetragonal I4/mcm and orthorhombic Pbnm. Analysis of the octahedral tilts suggest the co-existence of these two phases is a consequence of a first-order I4/mcm to Pbnm transition. The evolution of the structure of Sr_0.5Ca_0.5MnO₃ with temperature is also described and this is found to evolve from orthorhombic to tetragonal and ultimately cubic.     

Direct Observation of Oxygen Dissociation on Non‐Stoichiometric Metal Oxide Catalysts

Oxygen dissociation on metal oxides is a key reaction step, limiting the efficiency of numerous technologies. The complexity of the multi‐step oxygen reduction reaction (ORR) makes it difficult to investigate the oxygen dissociation step independently. Direct observation of the oxygen dissociation process is described, quantitatively, on perovskites La_0.6Sr_0.4Co_0.2Fe_0.8O_3‐δ and (La_0.8Sr_0.2)_0.95MnO_3±δ, using gas‐phase isotope‐exchange with a 1:1 ¹⁶O₂:¹⁸O₂ ratio. Oxygen transport mechanisms between gas–surface reactions and surface–bulk exchange are deconvoluted. Our findings show that regardless of participation of lattice oxygen, La_0.6Sr_0.4Co_0.2Fe_0.8O_3‐δ is better at oxygen dissociation than (La_0.8Sr_0.2)_0.95MnO_3±δ. Heteroexchange, involving lattice oxygen, dominates on La_0.6Sr_0.4Co_0.2Fe_0.8O_3‐δ. In contrast, (La_0.8Sr_0.2)_0.95MnO_3±δ shows both homoexchange and heteroexchange, with the latter only happening above 600 °C. Using a 1:1 isotope mixture, a simple method is presented for separation of the oxygen dissociation step from the overall ORR.     

Synthesis and electrocatalytic performance of La0.3Ce0.1Sr0.5Ba0.1TiO3 anode catalyst for solid oxide fuel cells

Ce-doped La_0.4Sr_0.5Ba_0.1TiO_3–δ (LCSBT) perovskite anode catalysts in solid oxide fuel cells were successfully synthesized by a modified rheological phase reaction for the first time. Pure LCSBT could be obtained under a reducing atmosphere and nano-CeO₂ particles could be exsoluted from LCSBT after being sintered in air. The catalytic activity and electrochemical performance of LCSBT anodes for the H₂ oxidation were obviously improved comparing with the pure La_0.4Sr_0.5Ba_0.1TiO_3–δ (LSBT) and LSBT&CeO₂ admixture anodes. The improved performance could be attributed to the nanostructure of LCSBT and the exsoluted nano-CeO₂ particles.     

Extension of the “1201” Family to Strontium-Rich Chromite and Ferrite, Bi0.4Sr2.5Cr1.1O4.9 and Bi0.4Sr2.5Fe1.1O5

Two new Sr-rich “1201”-type oxides, Bi_0.4Sr_2.5Cr_1.1O_4.9 and Bi_0.4Sr_2.5Fe_1.1O₅ have been synthesized. These compounds, intergrowths of double rock-salt layers with single perovskite layers, show a 1:1 ordering between (Bi,M) and Sr species within the intermediate rock-salt layer [Bi_0.4M_0.1Sr_0.5O]. The XANES study shows that bismuth is mainly trivalent, whereas iron is mixed valent containing 50% Fe³⁺ and 50% Fe⁴⁺ (also confirmed by Mössbauer), and chromium could be a mixture of Cr³⁺ and Cr⁶⁺ sitting in the perovskite and rock-salt-type sites, respectively. Both compounds exhibit antiferromagnetic interactions. The Cr-phase is a strong insulator, whereas the Fe-phase exhibits a semi-conductor-like resistivity whose value at room temperature is close to that of isotypic cobaltite.     

Synthesis and structural characterization of LaxSr1−xMnO2.6+δ (0.1<x<0.4) compounds displaying compressed octahedral coordination of Mn

La_xSr_1−xMnO_2.6+δ (x=0.1-0.4) compounds have been obtained by low-temperature annealing of stoichiometric materials in hydrogen. La_0.1Sr_0.9MnO_2.6+δ (δ=0.15) and La_0.3Sr_0.7MnO_2.6, tetragonal (P4/m), and La_0.2Sr_0.8MnO_2.6, pseudo-tetragonal monoclinic (P2/m), structures are isostructural with oxygen-vacancy-ordered Sr₅Mn₅O₁₃ (, c≈a_P). La_0.4Sr_0.6MnO_2.6 shows cubic perovskite structure with disordered oxygen vacancies. In the vacancy-ordered (La_xSr_1−x)₅Mn₅O₁₃ phases four out of five Mn cations are Mn³⁺ and show a typical Jahn-Teller elongated pyramidal coordination while the fifth one Mn^(4−5x)+, in octahedral environment, shows decreasing formal charge from Mn⁴⁺ (x=0) to Mn^2.5+x=0.3. This unusual selective doping of the octahedral site produces structural strain due to increasing size of the Mn^(4−5x)+ and, in the case of (La_0.2Sr_0.8)₅Mn₅O₁₃, the unusual compressed octahedral arrangement of oxygen atoms around it. The coordination geometry implies that either the d_x²-y² orbital is occupied, which would be a rare example of inverted occupancy of e_g orbitals in manganites, or that disordered Mn³⁺ apically elongated MnO₆ octahedra are present with normal electronic configuration , and the observed bond distances are the average of the long and intermediate in-plane Mn-O bonds. Several structural features favor the second case.     

Synthesis and characterization of monodisperse spherical SiO2@RE2O3 (RE=rare earth elements) and SiO2@Gd2O3:Ln (Ln=Eu, Tb, Dy, Sm, Er, Ho) particles with core-shell structure

Spherical SiO₂ particles have been coated with rare earth oxide layers by a Pechini sol-gel process, leading to the formation of core-shell structured SiO₂@RE₂O₃ (RE=rare earth elements) and SiO₂@Gd₂O₃:Ln³⁺ (Ln=Eu, Tb, Dy, Sm, Er, Ho) particles. X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), photoluminescence (PL), and cathodoluminescence spectra as well as lifetimes were used to characterize the resulting SiO₂@RE₂O₃ (RE=rare earth elements) and SiO₂@Gd₂O₃:Ln³⁺ (Eu³⁺, Tb³⁺, Dy³⁺, Sm³⁺, Er³⁺, Ho³⁺) samples. The obtained core-shell phosphors have perfect spherical shape with narrow size distribution (average size ca. 380 nm), smooth surface and non-agglomeration. The thickness of shells could be easily controlled by changing the number of deposition cycles (40 nm for two deposition cycles). Under the excitation of ultraviolet, the Ln³⁺ ion mainly shows its characteristic emissions in the core-shell particles from Gd₂O₃:Ln³⁺ (Eu³⁺, Tb³⁺, Sm³⁺, Dy³⁺, Er³⁺, Ho³⁺) shells.