Synthesis and characterization of poly(1,4-phenylenevinylene-alt-2,5-thienylenevinylene) derivatives for organic light-emitting diodes

A new series of alternating copolymers composed of 1,4-phenylenevinylene and 2,5-thienylenylvinylene repeating units with various side chain substituents were synthesized via the Heck coupling reaction for use in light-emitting diodes (LEDs). The resulting copolymers were characterized using ¹H- and ¹³C-NMR, DSC, and TGA. These polymers were found to be soluble in common organic solvents and are easily spin-coated onto glass substrates, producing high optical quality thin films without defects. The electro-optical properties of ITO/PEDOT/Polymer/Al devices were investigated using UV-VIS, PL and EL spectroscopy. The turn-on voltages of these devices were found to be in the range 4-16 V, with a maximum brightness of about 2900 cd/m² at 12 V.     

Analysis of trichroic infrared absorption in solids. II. One-way drawn poly(ethylene terephthalate)

The techniques of polarized infrared spectroscopy and sample tilting are applied to one-way drawn poly(ethylene terephthalate) (PET) films to calculate the trichroic absorption as a function of frequency. Of specific interest in this study is the distribution of vibrational modes in the plane transverse to the draw direction. The rotational isomeric content of the films is found by the method of least squares and compared with a density-method prediction of crystallinity. A two-phase model to describe PET morphology in the oriented state is examined and found to be inadequate. The segmental orientation as a function of strain is followed with five conformationally sensitive infrared modes. High segmental orientation is found in the trans conformers of both amorphous and crystalline phases. Little net segmental orientation in the gauche conformers of the amorphous phase occurs.     

Analysis of trichroic infrared absorption in solids. III. Phase I poly(vinylidene fluride)

Trichroic infrared absorption has been measured for oriented phase I poly(vinylidene fluoride). In addition to intensity differences, frequency shifts in the plane transverse to the draw direction are apparent. Shifts up to 10 cm^?1 in one-way drawn phase I are found for the CF₂ stretching vibration (880 cm^?1) between the direction normal to the film surface (thickness direction) and the remaining directions. Annealing the highly oriented films produces no major changes in the unique three-dimensional structure. A model based on crystal defect structures is proposed to explain the unusual frequency shift behavior in the phase I PVDF. Possible conformations and a mechanism of formation of the defects are discussed.     

Structure and properties of poly(2,5-dimethylterephthalamides)

Six methyl-substituted wholly aromatic polyamides were synthesized from the reaction of 2,5-dimethylterephthaloyl chloride with p-phenylenediamine, its 2,5-dimethyl and 2-methyl derivatives, m-phenylenediamine, or its 2-methyl and 4-methyl derivatives by solution polycondensation at low temperature. The x-ray diffraction diagrams of the polyamides obtained exhibit crystal patterns. Density values range from 1.26 to 1.37 g/cm³. NMR spectra determined in concentrated H₂SO₄ solution are reported. Poly(2,5-dimethylterephthalamides) have lower thermal stability than the corresponding polyterephthalamides. The increase in solubility of polyamide by the introduction of the 2,5-dimethylterephthaloyl linkage is accompanied by a decrease in thermal stability. The effect of methyl substituents on thermal properties and solubility is discussed in terms of the packing of polymeric molecules and the extent of hydrogen bonding of the amide groups.     

Regiodefined substituted poly(2,5-thienylene)s

The polymerization of 3,3″-dialkylterthiophenes overcomes the lack of regiospecificity associated (to some extent) with all the polymerization methods in use, thus allowing the preparation of perfectly regioregular polymers endowed with enhanced electrical and optical properties. Moreover, the larger spacing of the alkyl chains achieved with the insertion of an unsubstituted thiophene unit confers to such regioregular polymers an extraordinary doping stability. Two regiochemically defined alkoxy-substituted terthiophenes were also polymerized and the effects of the effects of the presence and position of the alkoxy group on the polymerization reaction and on the polymer properties are discussed. © 1993 John Wiley & Sons, Inc.     

Synthesis and electrical conductivity of poly(arylene vinylene). I. Poly(2,5-dimethoxyphenylene vinylene) and poly(2,5-dimethylphenylene vinylene)

The highly conjugated aromatic polymers, poly(2,5-dimethoxyphenylene vinylene) and poly(2,5-dimethylphenylene vinylene), were obtained from their water soluble, sulfonium salt precursor polymers. Films of these polymers were reacted with either AsF₅ or I₂ vapor. Poly(2,5-dimethoxyphenylene vinylene) showed increases in electrical conductivity of up to 14 to 15 orders of magnitude for these two dopants, while an 8 to 9 order of magnitude increase was observed for poly(2,5-dimethylphenylene vinylene) with the same dopants. The synthesis of the precursor polymers, the properties and elimination reactions of films of the precursors, the doping reactions, and the conductivities of the resulting phenylene vinylene films are discussed.     

Synthesis and properties of poly(2,5-ethylene benzimidazole)

Methyl β-(3,4-diaminophenyl)propionate, its hydrochloride, and β-(3,4-diaminophenyl)propionic acid were prepared and their structures were established. The effect of temperature, time, and pressure on the polymerization of these compounds and the molecular weight and structure of the resulting polymers were examined. Thin films of different polymer samples were prepared by compression molding, and their infrared spectra were used to study their structures. Samples of poly(2,5-ethylene benzimidazole) formed under typical polymerization conditions were shown by differential scanning calorimetry and x-ray techniques to be amorphous, and the glass transition temperature ranged between 201 and 240°C. The polymers were shown by thermogravimetric analysis to have good thermal stability, and 29–34% of the original weights remained after heating to 1000°C in nitrogen.     

NMR study of doped poly(2,5-dimethylaniline)

Structure changes and charge transfer in the doping process of poly(2,5-dimethylaniline) (PDMA) were studied by NMR technique. It was shown that not only the polymer chain but also the hydrogen atoms and methyl groups on the aromatic rings were involved in the charge transfer process. A “four ring BQ derivatives” model was proposed to explain the NMR results.     

Effects of dipolar coupling on the intensity of infrared absorption bands from supported metal catalysts

Although the influence of dipole coupling on spectra from adsorbed species has been much investigated in recent years, most of this work has concentrated on the frequency shifts induced by coupling, while the effects on intensity have been largely ignored. However, coupling can produce such profound changes in band intensities that serious mis-interpretation of spectra may arise if its influence is ignored: this is especially true for spectra obtained from relatively ill-defined substrates such as supported catalysts. Both absolute and relative band intensities are affected by coupling. Depolarization effects reduce molecular absorption intensities at high adsorbate densities, often very significantly; a reduction by a factor of 4 occurs with carbon monoxide molecules at a coverage of 10¹⁵ cm⁻². However, this influence of coupling is likely to be less important than the concomitant changes in the relative intensities of bands. These arise when two or more species with similar vibrational frequencies occur in physical proximity, and they then enhance the intensity of bands at high wavenumber, sometimes to such a degree that a species present to the extent of less than 5 % of the total may come to dominate the spectrum. Experiments have shown that slight variations in structure caused by surlhce defects can give rise to dramatic changes attributable to this effect.     

An evoluted bio-based 2,5-furandicarboxylate copolyester fiber from poly(ethylene terephthalate)

A series of bio-based poly(ethylene terephthalate-co-ethylene 2,5-furandicarboxylate) (PEFT) fibers was prepared via the industrially feasible melt-spinning and hot-drawing process. The effect of 2,5-furandicarboxylic acid (FDCA) content on the fibers properties was studied using differential scanning calorimetry, wide-angle X-ray diffraction, sound velocity, tensile, and boiling water shrinkage tests. It was found that the PEFT fibers showed comparable or superior tenacity to the PET fibers under the same conditions, especially the PEFT-4 fibers exhibited the highest tenacity (2.3, 2.9 cN/dtex for the drawn PET and PEFT-4 fibers prepared at the same take-up speed of 2500 m/min and a fixed draw ratio of 1.6). Moreover, the boiling water shrinkage of the PEFT fibers was quite close to that of the PET fibers under the same conditions, showing that the PEFT fibers were comparable to the PET fibers in heat resistance. The results indicated that the bio-based PEFT fibers would be a feasible alternative for the PET fibers, in terms of sustainability, processability, and mechanical properties. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 320–329     

Water absorption and desorption from the dipole ordered polymer poly(methylvinylidene cyanide)

From thermal desorption studies, we find evidence that absorbed water in the bulk of poly(methylvinylidene cyanide) is more weakly bound than is the case for copolymer films of poly(vinylidenefluoride-trifluoroethylene). Ultraviolet laser enhanced thermal desorption of absorbed water exhibits little light polarization dependence for poly(methylvinylidene cyanide) in contrast to absorbed water in copolymer films of poly(vinylidenefluoride-trifluoroethylene). The implications of these differences are discussed.     

Reflection–absorption infrared spectroscopy investigation of the crystallization kinetics of poly(ethylene terephthalate) ultrathin films

Reflection–absorption infrared spectroscopy was used to study the crystallization behavior of poly(ethylene terephthalate) (PET) ultrathin films. The crystallinity of ultrathin films was estimated by the fraction of trans conformers of PET. The isothermal and nonisothermal crystallization kinetics of ultrathin films with different thicknesses were investigated. The thinner PET film showed slower kinetics during isothermal crystallization than the thicker film. Moreover, the final crystallinity of films with various thicknesses were reduced with decreasing thickness. An Avrami equation was used to fit the acquired results. The Avrami exponents decreased with the film thickness. As for the nonisothermal crystallization, the cold‐crystallization starting temperature shifted to a lower temperature as the film thickness increased. The influence of the substrate on the crystallization kinetics of the films was also studied. The half‐crystallization times and final crystallinities of ultrathin films adsorbed onto a self‐assembled‐monolayer‐treated surface and an untreated substrate were clearly different, although their thickness dependence was similar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4440–4447, 2004     

Analysis on absorption spectra of Nd in poly(methyl methacrylate)

The absorption spectrum of neodymium (III) (Nd³⁺ doped in poly(methyl methacrylate) was measured. The Nephlauxetic effect was found in the spectrum compared to other spectra of Nd³⁺ doped in various matrices. The experimental data used, Slater-Condon parameters (F₂,F₄,F₆) and Lander parameter (ζ_4f) were calculated by the Taylor series expansion based on the assumption that the energy separation between J-levels of the 4fⁿ-configuration is a function of F₂,F₄,F₆ and ζ_4f. The Judd-Ofled intensity parameters (Ω₂,Ω₄,Ω₆) were also calculated. Analysis of the Nephlauxetic effect and the parameters variation on the host matrices was carried out.     

Preparation of soluble and fusible poly(2,5-dimethoxy-1,4-phenylene)

Poly(2,5-dimethoxy-1,4-phenylene) was prepared by oxidative polymerization of p-dimethoxybenzene with aluminum chloride and copper(II) chloride in nitrobenzene under reduced pressure. The polymers obtained were soluble in sulfuric acid and fusible at 320°C. The intrinsic viscosity of the polymer was ca. 0.07 in sulfuric acid. Demethylation of methoxy groups did not occur during the polymerization.     

Liquid crystalline,highly luminescent poly(2,5-dialkoxy-p-phenyleneethynylene)

A high-molecular-weight poly(2,5-dialkoxy-p-phenyleneethynylene) derivative has been prepared by the Heck reaction of 1,4-bis(2-ethylhexyloxy)-2,5-diiodobenzene and 1,4-diethynyl-2,5-dioctyloxybenzene. The highly luminescent polymer exhibits excellent solubility and can readily be processed into high-optical-quality films. The weight-average molecular weight M̄_w was 240000 g · mol⁻¹, with a polydispersity index of 2.9. Thermal analysis revealed a glass transition around 90°C, and an onset of chemical crosslinking at 130°C. The high M̄_w and the remarkable solubility enabled the preparation of liquid crystalline solutions of the new PPE.     

One-step electrochemical synthesis of pure poly(2,5-dicyano-p-phenylenevinylene) films

In this communication we describe the electrochemical synthesis of poly(2,5-dicyano-p-phenylenevinylene) (DCNPPV) polymer films on indium tin oxide substrates. We investigate the purity, morphology, absorption and emission properties of the film. The purity was checked by infrared spectroscopy. The film formed presented spectroscopic purity equivalent to the chemically prepared PPV that was dialyzed for one week. Scanning electron microscopy of the surface revealed a grain-like morphology. The absorption and emission spectra showed absorption and emission bands at 420 nm and 575 nm, respectively, with the absorption onset at 422 nm, which corresponds to an energy gap of 2.25 eV. The electrochemical determination of the energy gap gives 2.05 eV, thus quite close to the optical energy gap at the onset of absorption. The EA and IP were determined by electrochemical measurements and are 3.46 eV and 5.51 eV, respectively.