The adsorption of CO,O2, and H2 on Pt(100)-(5×20)

The adsorption/desorption characteristics of CO, O₂, and H₂ on the Pt(100)-(5 × 20) surface were examined using flash desorption spectroscopy. Subsequent to adsorption at 300 K, CO desorbed from the (5×20) surface in three peaks with binding energies of 28, 31.6 and 33 kcal gmol^?1. These states formed differently from those following adsorption on the Pt(100)-(1 × 1) surface, suggesting structural effects on adsorption. Oxygen could be readily adsorbed on the (5×20) surface at temperatures above 500 K and high O₂ fluxes up to coverages of $\text{2}\text{3}$ of a monolayer with a net sticking probability to ssaturation of ? 10^?3. Oxygen adsorption reconstructed the (5 × 20) surface, and several ordered LEED patterns were observed. Upon heating, oxygen desorbed from the surface in two peaks at 676 and 709 K; the lower temperature peak exhibited atrractive lateral interactions evidenced by autocatalytic desorption kinetics. Hydrogen was also found to reconstruct the (5 × 20) surface to the (1 × 1) structure, provided adsorption was performed at 200 K. For all three species, CO, O₂, and H₂, the surface returned to the (5 × 20) structure only after the adsorbates were completely desorbed from the surface.     

Chemical shifts in auger electron spectra from silicon in silicon nitride

The chemisorption of nitric oxide on (110) nickel has been investigated by Auger electron spectroscopy, LEED and thermal desorption. The NO adsorbed irreversibly at 300 K and a faint (2 × 3) structure was observed. At 500 K this pattern intensified, the nitrogen Auger signal increased and the oxygen signal decreased. This is interpreted as the dissociation of NO which had been bound via nitrogen to the surface. By measuring the rate of the decomposition as a function of temperature the dissociation energy is calculated at 125 kJ mol^?1. At ～860 K nitrogen desorbs. The rate of this desorption has been measured by AES and by quantitative thermal desorption. It is shown that the desorption of N₂ is first order and that the binding energy is 213 kJ mol^?1. The small increase in desorption temperature with increasing coverage is interpreted as due to an attractive interaction between adsorbed molecules of ～14 kJ mol^?1 for a monolayer. The (2 × 3) LEED pattern which persists from 500–800 K is shown to be associated with nitrogen only. The same pattern is obtained on a carbon contaminated crystal from which oxygen has desorbed as CO and CO₂. The (2 × 3) pattern has spots split along the (0.1) direction as $\text{(m,}\text{n}\text{3}\text{)}$ and $\text{(}\text{m}\text{2, n}\text{)}$. This is interpreted as domains of (2 × 3) structures separated by boundaries which give phase differences of $\text{2π}\text{3}$ and π. The split spots coalesce as the nitrogen starts to desorb. A (2 × 1) pattern due to adsorbed oxygen was then observed to 1100 K when the oxygen dissolved in the crystal leaving the nickel (110) pattern.     

The CO coadsorption and reactions of sulfur,hydrogen and oxygen on clean and sulfided Mo(100) and on MoS2(0001) crystal faces

The chemisorption and reactivity of O₂ and H₂ with the sulfided Mo(100) surface and the basal (0001) plane of MoS₂ have been studied by means of Thermal Desorption Spectroscopy (TDS), Auger Electron Spectroscopy (AES) and Low Energy Electron Diffraction (LEED). These studies have been carried out at both low (10^?8–10^?5Torr) and high (1 atm) pressures of O₂ and H₂. Sulfur desorbs from Mo(100) both as an atom and as a diatomic molecule. Sulfur adsorbed on Mo(100) blocks sites of hydrogen adsorption without noticeably changing the hydrogen desorption energies. TDS of ¹⁸O coadsorbed with sulfur on the Mo(100) surface produced the desorption of SO at 1150 K, and of S, S₂ and O, but not SO₂. A pressure of 1 × 10^?7 Torr of O₂ was sufficient to remove sulfur from Mo(100) at temperatures over 1100 K. The basal plane of MoS₂ was unreactive in the presence of 1 atm of O₂ at temperatures of 520 K. Sputtering of the MoS₂ produced a marked uptake of oxygen and the removal of sulfur under the same conditions.     

Characterization of oxygen,carbon, and sulfur adlayers on W(211)

Adlayers of oxygen, carbon, and sulfur on W(211) have been characterized by LEED, AES, TPD, and CO adsorption. Oxygen initially adsorbs on the W(211) surface forming p(2 × 1)O and p(1 × 1)O structures. Atomic oxygen is the only desorption product from these surfaces. This initial adsorption selectively inhibits CO dissociation in the CO(β₁) state. Increased oxidation leads to a p(1 × 1)O structure which totally inhibits CO dissociation. Volatile metal oxides desorb from the p(1 × 1)O surface at 1850 K. Oxidation of W(211) at 1200 K leads to reconstruction of the surface and formation of p(1 × n)O LEED patterns, 3 ? n ? 7. The reconstructed surface also inhibits CO dissociation and volatile metal oxides are observed to desorb at 1700 K, as well as at 1850 K. Carburization of the W(211) surface below 1000 K produced no ordered structures. Above 1000 K carburization produces a c(6 × 4)C which is suggested to result from a hexagonal tungsten carbide overlayer. CO dissociation is inhibited on the W(211)?c(6×4)C surface. Sulfur initially orders into a c(2 × 2)S structure on W(211). Increased coverage leads to a c(2×6)S structure and then a complex structure. Adsorbed sulfur reduces CO dissociation on W(211), but even at the highest sulfur coverages CO dissociation was observed. Sulfur was found to desorb as atomic S at 1850 K for sulfur coverages less than $\text{7}\text{6}$ monolayers. At higher sulfur coverages the dimer, S₂, was observed to desorb at 1700 K in addition to atomic sulfur desorption.     

The adsorption of CO,H2, H2, CO2 and H2O on carburized and graphitized Ni(110)

A study of the adsorption/desorption behavior of CO, H₂O, CO₂ and H₂ on Ni(110)(4 × 5)-C and Ni(110)-graphite was made in order to assess the importance of desorption as a rate-limiting step for the decomposition of formic acid and to identify available reaction channels for the decomposition. The carbide surface adsorbed CO and H₂O in amounts comparable to the clean surface, whereas this surface, unlike clean Ni(110), did not appreciably adsorb H₂. The binding energy of CO on the carbide was coverage sensitive, decreasing from 21 to 12 $\text{kcal}\text{mol}$ as the CO coverage approached 1.1 × 10¹⁵ molecules cm^?2 at 200K. The initial sticking probability and maximum coverage of CO on the carbide surface were close to that observed for clean Ni(110). The amount of H₂, CO, CO₂ and H₂O adsorbed on the graphitized surface was insignificant relative to the clean surface. The kinetics of adsorption/desorption of the states observed are discussed.     

Reactive scattering of small molecules from platinum crystal surfaces: D2CO,CH3OH,HCOOH, and the nonanomalous kinetics of hydrogen atom recombination

The decomposition of D₂CO, CH₃OD and HCOOH on Pt(110) and of D₂CO on Pt(S)-[9(111) × (100)] was studied by molecular beam relaxation spectroscopy. D₂CO and CH₃OD evolved CO and H₂ via a desorption limited sequence of elementary steps. The rate constant for CO desorption from Pt(110) was 6 × 10¹⁴exp(? 35.5 $\text{kcal}\text{gmol}$ · RT) s^?1, and from Pt(S)-[9(111) × (100)] it was 1 × 10¹⁵ exp(?36.2 $\text{kcal}\text{gmol}\text{·RT}$) s^?1. On Pt(110) the rate constant for hydrogen formation was 10^{0 ± 1}exp(?24 $\text{kcal}\text{gmol}\text{·RT}$) $\text{m}\text{?}{}^2\text{atom}$ · s. On Pt(S)-[9(111) × (100)] two pathways for H₂ formation existed with rate constants of 8.7 × 10^?2exp( ?24.9 $\text{kcal}\text{gmol}\text{· RT}$) $\text{cm}{}^2\text{atom}$· s and 3.2 × 10^?3 exp(?19.5 $\text{kcal}\text{gmol}\text{·RT}$) $\text{cm}{}^2\text{atom}\text{·}$ s. These pre-exponential factors are in order of magnitude agreement with values typical of hydrogen recombination on other metals. When a small amount of sulfur ( ~ 0.1 ML) was adsorbed on the stepped Pt surface, only one pathway for H₂ formation existed due to blockage of stepped sites. A similar result was obtained when a beam of CO was impinged on the surface. Formic acid decomposed via a branched process to form primarily CO₂ and H₂.     

A study of SO2 adsorption on CaO (100) surfaces using X-ray photoelectron spectroscopy

The adsorption of SO₂ on CaO (100) at 300 K has been studied using X-ray photoelectron spectroscopy. Under ultrahigh-vacuum conditions, the surface was exposed to 0–500 Langmuirs of SO₂. The resulting adsorption yields a single SO surface species with an S 2p peak at 168.2 eV and an O 1s_{$\text{sol1}\text{2}$} peak at 531.7 eV. Subsequent heating of the exposed surface to 673 K indicated no desorption or changes in the binding energies of the S 2p and O 1s_{$\text{1}\text{2}$} peaks. On the basis of these data and binding-energy data for standard compounds, the adsorbed species is identified as SO₄^2?. The surface coverage due to the SO₄^2? species was also measured as a function of SO₂ exposure. From these data, the initial adsorption is found to be first-order in surface coverage, and the initial sticking probability is found to have a value of 0.4.     

Adsorption and surface structural chemistry of Na and Na + O2 on Ag(110)

The adsorption of Na and the coadsorption of Na and O₂ on Ag(110) have been studied by LEED, thermal desorption, and Auger spectroscopy. For Na coverages in the regime 0 < θ_Na < 2 the Na desorption spectra show a single peak (β) corresponding to a desorption energy of ～195 kJ mol^?1, and at θ_Na ～ 2 a (1 × 2) LEED pattern appears. At still higher coverages (2 < θ_Na < 5), a (1 × 3) surface phase is formed, and a new peak (α) appears in the desorption spectra; this is identified with Na desorption from an essentially Na surface. The desorption energy of αNa (～174 kJ mol^?1) indicates that Na adatoms beyond the first chemisorbed layer are significantly influenced by the presence of the Ag substrate. The initial sticking probability of O₂ on Na-dosed Ag(110) is enormously enhanced over the clean surface value, being of the order of unity, and O₂ chemisorption ultimately leads to a (4 × 1) surface structure. The presence either subsurface Na alone, or of both Na and O below the surface, causes substantial changes in surface behaviour. In the former case, submonolayer doses of Na lead to the appearance of a (1 × 2) structure; and in the latter case, Na + O₂ coadsorption results in a c(4 × 2) structure. Auger spectroscopy indicates that the Ag(110)-c(4 × 2)$\text{Na}\text{O}$ phase forms with a constant stoichiometry which is independent of the initial Na dose. The Na:O ratio in this adlayer is believed to be of the order of unity. The structures of the various ordered phases, the nature of the AgNa bonding, and the interatomic spacing between the alkali adatoms on Ag(110) are discussed.     

Adsorption of CO on clean and oxygen covered Ni(111) surfaces

Adsorption of CO on Ni(111) surfaces was studied by means of LEED, UPS and thermal desorption spectroscopy. On an initially clean surface adsorbed CO forms a √3 × $\text{√3}\text{R30°}$ structure at θ = 0.33 whose unit cell is continuously compressed with increasing coverage leading to a c4 × 2-structure at θ = 0.5. Beyond this coverage a more weakly bound phase characterized by a $\text{√7}\text{2}$ × $\text{√7}\text{2R19°}$ LEED pattern is formed which is interpreted with a hexagonal close-packed arrangement (θ = 0.57) where all CO molecules are either in “bridge” or in single-site positions with a mutual distance of 3.3 Å. If CO is adsorbed on a surface precovered by oxygen (exhibiting an O 2 × 2 structure) a partially disordered coadsorbate 2 × 2 structure with θ_o = θ_co = 0.25 is formed where the CO adsorption energy is lowered by about 4 kcal/mole due to repulsive interactions. In this case the photoemission spectrum exhibits not a simple superposition of the features arising from the single-component adsorbates (i.e. maxima at 5.5 eV below the Fermi level with O_ad, and at 7.8 (5σ + 1π) and 10.6 eV (4σ) with CO_ad, respectively), but the peak derived from the CO 4σ level is shifted by about 0.3 eV towards higher ionization energies.     

The co-adsorption of copper and oxygen on a tungsten {100} surface

The co-adsorption of Cu on O₂ and a W{100}surface is studied by Auger electron spectroscopy (AES), thermal desorption (TD), low energy electron diffraction (LEED) and by work function change (δø) measurements. It is shown that the presence of Cu on the surface initially decreases s_O, the sticking coefficient of O₂. For longer oxygen exposures and for higher adsorption temperatures, θ_O reaches values larger than those on the clean surface for the same O₂ exposure. Except at the highest θ_O values and temperatures, the sticcking coefficient for copper, s_Cu, is unity and is independent of the oxygen coverage θ_O in the range studied (0 ? θ_O ? 2). Co-adsorption at room temperatures does not produce any long range order while co-adsorption at elevated temperature leads to the ordered structures (1 × 1), p(2 × 1), p(2 × 2) and c(2 × 2). The saturation coverage of the two dimensional co-adsorbate at 800 K is given by the relation $\text{θ}{}_{\mathrm{Cu}}\text{+}\text{8}\text{5}\text{θ}{}_{\mathrm{O}}\text{= 2}$. The work function is a complicated function of θ_O and θ_Cu and is determined predominantly by the temperature at which oxygen is adsorbed. At high temperatures the sequence of adsorption has no influence, in contrast to the room temperature behavior.     

The effect of sulfur on co adsorption/desorption on Pt(S)-[9(111) × (100)]

CO adsorption/desorption on clean and sulfur covered Pt(S)-[9(111) × (100)] surfaces was studied using AES, TPD, and modulated beam experiments. CO desorption occurred from two states on the clean surface — a low temperature state associated with the (111) terraces and a high temperature state associated with the steps/defects. Thermal desorption results indicated that above small CO coverages conversion from the low temperature state into the high temperature state was activated and that back conversion was slow. Sulfur preferentially adsorbed at step/defect sites and decreased the population of the high temperature desorption state. Modulated beam experiments were performed in order to determine CO adsorption/desorption parameters as a function of sulfur coverage on the Pt crystal. The sticking coefficient and binding energy of CO decreased as the sulfur concentration increased. Sulfur adsorption at step/defect sites decreased the CO sticking coefficient only slightly but increased the effective rate constant for CO desorption significantly. Sulfur adsorption on the terraces affected CO adosrption more than sulfur at step sites. On the clean surface the effective rate constant for CO desorption was

$\text{1 × 10}{}^{15}\text{s}{}^{\mathrm{?1}}\text{exp (}\text{?36.2 kcal/mole}\text{RT}\text{)}$

Desorption occurred from both terrace and step/defect sites, but the kinetics were characteristic of the step/defect sites. For the surface on which step/defect sites were blocked by sulfur the effective desorption rate constant was

$\text{k}{}_{\mathrm{eff}}\text{= 1 × 10}{}^{13}\text{s}{}^{\mathrm{?1}}\text{exp (?}\text{27.5 kcal/mole}\text{RT}\text{)}$

indicating an appreciable decrease in CO binding on the terraces, though sulfur-CO repulsive interactions had probably made k_eff larger than the true rate constant for desorption from clean (111) planes. The results showed clearly a compensation effect in activation energy and preexponential factor.     

Oxygen chemisorption and the carbon monoxide-oxygen interaction on Ru(101)

The adsorption of oxygen and the interaction of carbon monoxide with oxygen on Ru(101) have been studied by LEED, Auger spectroscopy and thermal desorption. Oxygen chemisorbs at 300 K via a precursor state and with an initial sticking probability of ~0.004, the enthalpy of adsorption being ~300 kJ mol^?1. As coverage increases a well ordered ¦11,30¦ phase is formed which at higher coverages undergoes compression along [010] to form a ¦21,50¦ structure, and the surface eventually saturates at 0 ~ $\text{8}\text{9}$. Incorporation of oxygen into the subsurface region of the crystal leads to drastic changes in the surface chemistry of CO. A new high; temperature peak (γ CO, E_d ~ 800 kJ mol^?1) appears in the desorption spectra, in addition to the α and β CO peaks which are characteristic of the clean surface. Coadsorption experiments using ¹⁸O₂ indicate that γ CO is not dissociatively adsorbed, and this species is also shown to be in competition with β CO for a common adsorption site. The unusual temperature dependence of the LEED intensities of the ¦11,30¦-O phase and the nature of α, β, and β CO are discussed. Oxygen does not displace adsorbed CO at 300 K and the converse is also true, neither do any Eley-Rideal or Langmuir-Hinshelwood reactions occur under these conditions. Such processes do occur at higher temperatures, and in particular the reaction CO(g) + O(a) → CO₂(g) appears to occur with much greater collisional efficiency than on Ru(001). The oxidation of CO has been examined under steady state conditions, and the reaction was found to proceed with an apparent activation energy of 39 kJ mol^?. This result rules out the commonly accepted explanation that CO desorption is rate determining, and is compared with the findings of other authors.     

A proposed experiment to measure surface roughness in Si/SiO2 system

The adsorption of oxygen on clean cleaved (111) silicon surfaces has been investigated by high resolution electron spectroscopy (HRES), Auger electron spectroscopy (AES) and ellipsometry. Localized vibrations ($\text{h}\text{?}\text{ω = 94}$, 130 and 175 meV) which are related to the binding state band of oxygen are identified with HRES. AES measures the concentration of adsorbed atoms basically independent of their binding state while ellipsometry refers additionally to the optical properties of the adsorbed layer. The same adsorption kinetics was found with the three methods. Oxygen therefore adsorbs in a single likely molecular state. The sticking coefficient S increases exponentially with the surface step concentration. S is also enhanced by the presence of nude ion gauges. Depending on these parameters sticking coefficients between 2 × 10^?4 and 10^?1 have been obtained. This result might contribute to an explanation of the large differences in earlier works.     

Adsorption of oxygen on Pt(111)

Oxygen adsorbed on Pt(111) has been studied by means of temperature programmed thermal desorption spectroscopy (TPDS). high resolution electron energy loss spectroscopy (EELS) and LEED. At about 100 K oxygen is found to be adsorbed in a molecular form with the axis of the molecule parallel to the surface as a peroxo-like species, that is, the OO bond order is about 1. At saturation coverage (θ_mol= 0.44) a $\text{(}\text{3}\text{2}\text{×}\text{3}\text{2}\text{)R15°}$ diffraction pattern is observed. The sticking probability S at 100 K as a function of coverage passes through a maximum at θ = 0.11 with S = 0.68. The shape of the coverage dependence is characteristic for adsorption in islands. Two coexisting types of adsorbed oxygen molecules with different OO stretching vibrations are distinguished. At higher coverages units with v-OO = 875 cm^?1 are dominant. With decreasing oxygen coverages the concentration of a type with v-OO = 700 cm^?1 is increased. The dissociation energy of the OO bond in the speices with v-OO = 875 cm^?1 is estimated from the frequency shift of the first overtone to be ~ 0.5 eV. When the sample is annealed oxygen partially desorbs at ~ 160K, partially dissociates and orders into a p(2×2) overlayer. Below saturation coverage of molecular oxygen, dissociation takes place already at92 K. Atomically adsorbed oxygen occupies threefold hollow sites, with a fundamental stretching frequency of 480 cm^?1. In the non-fundamental spectrum of atomic oxygen the overtone of the E-type vibration is observed, which is “dipole forbidden” as a fundamental in EELS.     

Determination of the c(2 × 2) structure of sulfur on Fe{001} by low-energy electron diffraction

In the early stages of reaction with sulfur, a clean Fe{001} surface develops a c(2 × 2) superstructure. A low-energy electron diffraction analysis of this structure leads to a model in which the S atoms lie in the four-fold symmetrical sites on the Fe{001} surface, the S-Fe interplanar spacing being $\text{1.09 ± 0.05}\text{A}\text{?}$ and corresponding to an effective radius of 1.06 Å for the chemisorbed S atoms. In contrast to Fe{001} 1 × 1-O, the first interlayer spacing of the substrate here is not significantly expanded.     

A leed-aes study of the structure of sulfur monolayers on the Mo(100) crystal face

The formation of ordered phases of sulfur on the molybdenum (100) crystal face has been studied by Low Energy Electron Diffraction (LEED), Auger Electron Spectroscopy (AES) and Thermal Desorption Spectroscopies (TDS). Sulfur was deposited from a S₂ molecular flux streaming out of an Ag₂S containing electrochemical cell inside the UHV chamber. The use of a controlled flux of S₂ allowed the careful determination of saturation values for the monolayer, as well as the formation of multilayers of sulfur. This allowed the calibration of Auger intensities in terms of sulfur coverage. Various ordered structures, c(2 × 2), (1 × 2), $\text{2}\text{1}\text{?}\text{1}\text{1}$ and c(2 × 4), were observed by LEED for different values of the S coverage. Real space models for these structures are proposed that satisfy the coverage values observed and place sulfur atoms only on high symmetry four-fold sites on the (100) molybdenum surface.     

The adsorption of acetylene on W(100) at room temperature: An electron spectroscopic study

The adsorption of acetylene on W(100) at room temperature has been studied by AES, ELS, thermal desorption, mass spectrometry, work function and LEED in one vacuum chamber. AES line profile analysis shows that there are at least two adsorption processes occurring at room temperature. Further, it is possible to explain all the AES results by assuming non-sequential adsorption into just two states, denoted by α and β. This picture was substantiated and embellished by comparison with other standard surface techniques. The α-state comprises either a C₂H₂ unit with an activation energy for desorption of $\text{2.3}\text{eV}\text{molecule}\text{(53}\text{kcal mole}{}^{\mathrm{?1}}\text{)}$ or CH units bounded through the carbon of the β-state. Saturation coverage for the α-state is 3 × 10¹⁴ molecules cm^?2. The β-state is dissociative at low acetylene exposures and comparison between a carbon covered surface and the β-state suggest the latter to be dissociative up to saturation. There also appears to be ca. 10¹⁴ hydrogen atoms cm^?2 on W(100) on room temperature acetylene saturation, the carbon content of the β-state being 9 × 10¹⁴ atoms cm^?2. The residual C?C bond from the molecule in the β-state remains unknown. No sign of ordering in the adsorbed species was detected, save the possibility of (1 × 1) in the β-state. Acetylene adsorption at 580 K showed hydrogen from the β-state to block acetylene adsorption by 15% at saturation. A two-site adsorption model for the β-state is proposed to explain the results. The α-state is bonded through the carbon of the β-state and it is speculated that the former adsorbs onto “β” domains where there is a critical minimum size for the latter.     

Chemisorption and surface reactivity of nitric oxide on clean and sodium-dosed Ag(110)

The chemisorption of NO on clean and Na-dosed Ag(110) has been studied by LEED, Auger spectroscopy, and thermal desorption. On the clean surface, non-dissociative adsorption into the α-state occurs at 300 K with an initial sticking probability of ～0.1, and the surface is saturated at a coverage of about $\text{1}\text{25}$. Desorption occurs without decomposition, and is characterised by an enthalpy of E_d ～104 kJ mol^?1 — comparable with that for NO desorption from transition metals. Surface defects do not seem to play a significant role in the chemistry of NO on clean Ag, and the presence of surface Na inhibits the adsorption of αNO. However, in the presence of both surface and subsurface Na, both the strength and the extent of NO adsorption are markedly increased and a new state (β₁NO) with E_d ～121 kJ mol^?1 appears. Adsorption into this state occurs with destruction of the Ag(110)-(1 × 2)Na ordered phase. Desorption of β₁NO occurs with significant decomposition, N₂ and N₂O are observed as geseous products, and the system's behaviour towards NO resembles that of a transition metal. Incorporation of subsurface oxygen in addition to subsurface Na increases the desorption enthalpy (β₂NO), maximum coverage, and surface reactivity of NO still further: only about half the adsorbed layer desorbs without decomposition. The bonding of NO to Ag is discussed, and comparisons are made with the properties of α and βNO on Pt(110).     

Adsorption,coadsorption, and reactivity of sodium and nitric oxide on Ag(111)

The adsorption, desorption, and surface structural properties of Na and NO on Ag(111), together with their coadsorption and surface reactivity, have been studied by LEED, Auger spectroscopy, and thermal desorption. On the clean surface, non-dissociative adsorption of NO into the a-state occurs at 300 K with an initial sticking probability of ~0.1, saturation occurring at a coverage of $\text{~}\text{1}\text{20}$. Desorption occurs reversibly without decomposition and is characterised by a desorption energy of E_d ~ 103 kJ mol^?1. In the coverage regime 0 < θ_Na < 1, sodium adsorbs in registry with the Ag surface mesh and the desorption spectra show a single peak corresponding to E_d ~ 228 kJ mol^?1. For multilayer coverages (1 < θ _Na < 5) a new low temperature peak appears in the desorption spectra with E_d ~ 187 kJ mol^?1. This is identified with Na desorption from an essentially Na surface, and the desorption energy indicates that Na atoms beyond the first chemisorbed layer are significantly influenced by the presence of the Ag substrate. The LEED results show that Na multilayers grow as a (√7 × √7) R19.2° overlayer, and are interpreted in a way which is consistent with the above conclusion. Coadsorption of Na and NO leads to the appearance of a more strongly bound and reactive chemisorbed state of NO (β-NO) with E_d ~ 121 kJ mol^?1. β-NO appears to undego surface dissociation to yield adsorbed O and N atoms whose subsequent reactions lead to the formation of N₂, N₂O, and O₂ as gaseous products. The reactive behaviour of the system is complicated by the effects of Na and O diffusion into the bulk of the specimen, but certain invariant features permit us to postulate an overall reaction mechanism, and the results obtained here are compared with other relevant work.     

Interaction of NO with a Ni (111) surface

The interaction of NO with a Ni (111) surface was studied by means of LEED, AES, UPS and flash desorption spectroscopy. NO adsorbs with a high sticking probability and may form two ordered structures (c4 × 2 and hexagonal) from (undissociated) NO_ad. The mean adsorption energy is about 25 $\text{kcal}\text{mole}$. Dissociation of adsorbed NO starts already at ?120°C, but the activation energy for this process increases with increasing coverage (and even by the presence of preadsorbed oxygen) up to the value for the activation energy of NO desorption. The recombination of adsorbed nitrogen atoms and desorption of N₂ occurs around 600 °C with an activation energy of about 52 $\text{kcal}\text{mole}$. A chemisorbed oxygen layer converts upon further increase of the oxygen concentration into epitaxial NiO. A mixed layer consisting of N_ad + O_ad (after thermal decomposition of NO) exhibits a complex LEED pattern and can be stripped of adsorbed oxygen by reduction with H₂. This yields an N_ad overlayer exhibiting a 6 × 2 LEED pattern. A series of new maxima at ≈ ?2, ?8.8 and ?14.6 eV is observed in the UV photoelectron spectra from adsorbed NO which are identified with surface states derived from molecular orbitals of free NO. N_ad as well as O_ad causes a peak at ?5.6 eV which is derived from the 2p electrons of the adsorbate. The photoelectron spectrum from NiO agrees closely with a recent theoretical evaluation.