C_2H_x(x=4～6)在Ni(111)表面吸附的DFT研究

采用密度泛函理论与周期平板模型相结合的方法,对物种C_2H_x(x=4～6)在Ni(111)表面的top,fcc,hcp和bridge位的吸附模型进行了结构优化、能量计算,得到了各物种较有利的吸附位;并对最佳吸附位进行密立根电荷和总态密度分析.结果表明:C_2H_6和C_2H_4在Ni(111)表面的最稳定吸附位都是top位,吸附能分别是-36.41和-48.62 kJ·mol~(-1),物种与金属表面吸附较弱;而C_2H_5在Ni(111)表面的最稳定吸附位hcp的吸附能是-100.21 kJ·mol~(-1),物种与金属表面较强;三物种与金属表面之间都有电荷转移,属于化学吸附.     

Thermoelectric performance of XI2 (X = Ge,Sn, Pb) bilayers

We study the thermal and electronic transport properties as well as the thermoelectric (TE) performance of three two-dimensional (2D) XI₂ (X=Ge, Sn, Pb) bilayers using density functional theory and Boltzmann transport theory. We compared the lattice thermal conductivity, electrical conductivity, Seebeck coefficient, and dimensionless figure of merit (ZT) for the XI₂ monolayers and bilayers. Our results show that the lattice thermal conductivity at room temperature for the bilayers is as low as ~1.1 W·m^{-1·K-1-1.7 W}·m^{-1·K-1, which is about 1.6 times as large as the monolayers for all the three materials. Electronic structure calculations show that all the} XI₂ bilayers are indirect-gap semiconductors with the band gap values between 1.84 eV and 1.96 eV at PBE level, which is similar as the corresponding monolayers. The calculated results of ZT show that the bilayer structures display much less direction-dependent TE efficiency and have much larger n-type ZT values compared with the monolayers. The dramatic difference between the monolayer and bilayer indicates that the inter-layer interaction plays an important role in the TE performance of XI₂, which provides the tunability on their TE characteristics.     

O在Au(111)表面吸附的密度泛函理论研究

应用密度泛函理论，本文系统地研究了O在Au(111)表面上的吸附能、吸附结构、功函数、电子密度和投影态密度，给出了覆盖度从0.11ML到1.0ML的范围内，O的吸附特性随覆盖度变化的规律.研究发现O的稳定吸附位为3重面心立方(fcc)洞位，O在fcc洞位的吸附能对覆盖度比较敏感，其值随着覆盖度的增加而减小；O诱导Au(111)表面功函数的变化量与覆盖度成近线性关系，原因是Au表面电子向O偏移，形成表面偶极子；O—Au的相互作用形成成键态和反键态，且反键态都被占据，造成O—Au键很弱，O吸附能较小. 关键词： 表面吸附 Au(111)表面 密度泛函理论 电子特性     

Pressure-induced phase transitions in the ZrXY (X= Si,Ge, Sn;Y= S,Se, Te) family compounds

Pressure is an effective and clean way to modify the electronic structures of materials, cause structural phase transitions and even induce the emergence of superconductivity. Here, we predicted several new phases of the ZrXY family at high pressures using the crystal structures search method together with first-principle calculations. In particular, the ZrGeS compound undergoes an isosymmetric phase transition from P4/nmm-I to P4/nmm-II at approximately 82 GPa. Electronic band structures show that all the high-pressure phases are metallic. Among these new structures, P4/nmm-II ZrGeS and P4/mmm ZrGeSe can be quenched to ambient pressure with superconducting critical temperatures of approximately 8.1 K and 8.0 K, respectively. Our study provides a way to tune the structure, electronic properties, and superconducting behavior of topological materials through pressure.     

Structural phase transitions at clean and metal-covered Si(111) surfaces investigated by RHEED spot analysis

Structural phase transitions between various kinds of superlattice structures formed on a Si(111) surface have been investigated by spot analysis of reflection high-energy electron diffraction (RHEED). Reversible transitions induced by temperature changes and irreversible ones induced by metal depositions were observed. Detailed discussions on the dynamics of the phase transitions are made by quantitative analyses of integrated spot intensity and profile. For a phase transition of 7′7  1′1 structures on a clean Si(111) surface, a hysteresis with temperature difference of 5°C. between in heating and cooling processes was found in the spot intensity change, indicating a first-order transition. Hysteresis was hardly recognized, on the other hand, for transitions of Au-induced superstructures (5×2-Au or ×-Au)  1×1-Au. The spot profiles were found to be broadened during the transition of Si(111)-×-Au  1×1-Au, which was a signature of a continuous transition, while the profiles remained unchanged during the transitions of the 7×7  1×1 and 5×2-Au  1×1-Au phases. Structural conversions induced by In adsorption on the Si(111) surface kept at constant temperatures were also analyzed. The conversions at room temperature were totally dependent on the initial substrate surface structures; the 7×7 surface did not show any structural conversion with In adsorption, while the ×-In surface successively converted to a 2×2 and a × phase with coverage increase. The structural transitions at elevated temperatures were sensitively dependent on the temperatures. Sequences of transitions among the 7×7, 4×1, ×, 1×, and ×4 were quantitatively revealed as changes in RHEED spot intensity.     

甲基和羟基在Ir(111)表面吸附的密度泛函理论研究

在超原胞近似和slab模型基础上,采用周期性密度泛函理论,在0.11覆盖度(ML)下,对甲基与羟基在Ir(111)表面的吸附进行了研究,得到了甲基和羟基在Ir(111)表面不同吸附位置的吸附能和吸附构型,计算了它们的振动频率,同时分析了甲基和羟基共吸附于Ir(111)表面的情况.结果表明,甲基和羟基在Ir(111)表面的最稳定吸附位置都是top位,甲基是碳端向下吸附,羟基是通过氧端向下倾斜吸附.通过频率分析发现吸附后CH3中C-H键的对称伸缩振动、反对称伸缩振动以及剪切振动频率均发生了红移,而羟基中的O-H键的振动频率发生蓝移现象.通过计算对比发现甲醇分解为甲基和羟基过程是一个放热反应,从热力学角度来说该反应是可行的.     

甲基和羟基在Ir(111)表面吸附的密度泛函理论研究

在超原胞近似和slab模型基础上,采用周期性密度泛函理论,在0.11覆盖度（ML）下,对甲基与羟基在Ir(111)表面的吸附进行了研究,得到了甲基和羟基在Ir(111)表面不同吸附位置的吸附能和吸附构型,计算了它们的振动频率,同时分析了甲基和羟基共吸附于Ir(111)表面的情况。结果表明,甲基和羟基在Ir(111)表面的最稳定吸附位置都是top位,甲基是碳端向下吸附,羟基是通过氧端向下倾斜吸附。通过频率分析发现吸附后CH3中C-H键的对称伸缩振动、反对称伸缩振动以及剪切振动频率均发生了红移,而羟基中的O-H键的振动频率发生蓝移现象。通过计算对比发现甲醇分解为甲基和羟基过程是一个放热反应,从热力学角度来说该反应是可行的。     

Mg-Sn-Si合金中Mg2(Si,Sn)复合相的结构与性能研究

研究了铸态Mg-Sn-Si合金中Mg₂(Si,Sn)复合相的结构、 特性以及该相对Mg-Sn-Si合金变质作用的影响. 结果表明: Sn原子能取代Mg₂Si中的部分Si生成Mg₂(Si,Sn)复合相, 该三元相与Mg₂Si, Mg₂Sn相的结构相同, 属于面心立方结构, Mg₂(Si,Sn)相的元素含量并不固定, 在Si富集区形成的Mg₂(Si,Sn)相中, Si元素含量高, 在Si贫乏区形成的Mg₂(Si,Sn)相中, Si元素含量低. Si含量较多的Mg₂(Si,Sn)相性能与Mg₂Si相接近, Sn含量较多的Mg₂(Si,Sn)相性能与Mg₂Sn相接近, 实验中发现Mg₂(Si,Sn)复合相的纳米硬度、 弹性模量与维氏硬度等物理性能介于Mg₂Si与Mg₂Sn之间, Mg₂(Si,Sn)相对汉字状Mg₂Si相的变质处理起到桥梁作用. 关键词： Mg-Sn-Si合金 2Si')" href="#">Mg₂Si 2Sn')" href="#">Mg₂Sn 2(Si,Sn)复合相')" href="#">Mg₂(Si,Sn)复合相     

A density functional theory study on the adsorption of CO and O2 on Cu-terminated Cu2O （111） surface

The adsorptions of CO and 02 molecules individually on the stoichiometric Cu-terminatcd Cu20 （111） surface are investigated by first-principles calculations on the basis of the density functional theory. The calculated results indicate that the CO molecule preferably coordinates to the Cu2 site through its C atom with an adsorption energy of-1.69 eV, whereas the 02 molecule is most stably adsorbed in a tilt type with one O atom coordinating to the Cu2 site and the other O atom coordinating to the Cul site, and has an adsorption energy of -1.97 eV. From the analysis of density of states, it is observed that Cu 3d transfers electrons to 2π orbital of the CO molecule and the highest occupied 5σ orbital of the CO molecule transfers electrons to the substrate. The sharp band of Cu 4s is delocalized when compared to that before the CO molecule adsorption, and overlaps substantially with bands of the adsorbed CO molecule. There is a broadening of the 2π orbital of the 02 molecule because of its overlapping with the Cu 3d orbital, indicating that strong 3d-2π interactions are involved in the chemisorption of the 02 molecule on the surface.     

Reconstruction-Determined Diffusion of Ag Adatoms on the Si(111)-(7X7) Surface

Surface diffusion is one of the basic processes determining morphology of a growing film. In the case of metal heteroepitaxy on Si(111)-(7X7) the diffusion is strongly affected by the presence of surface reconstruction, which introduces additional constraints into the motion of deposited atoms. To determine diffusion parameters we used two different approaches: i) interpretation of experimentally observed morphologies by a coarse-grained kinetic Monte Carlo model, ii) direct observation of adatom movement using UHV STM. The attempt frequency and the barrier to hopping of a single Ag atom between half-unit cells of the reconstruction were estimated in both cases. Obtained values are compared and discussed.     

First-principle investigation on the thermodynamics of X_2N_2O(X = C,Si, Ge) compounds

The structures under different pressures, elastic properties, electronic structures and lattice vibrations of the X_2N_2O(X = C, Si, Ge) compounds are investigated by using the first-principle method. Based on the phonon density of state,the thermodynamic properties of the present compounds are studied under different pressures and at different temperatures. The structural parameters including the bond lengths and bond angles are in agreement with available experimental measurements and theoretical calculations. We employ the elastic theory to calculate the nine independent elastic constants(C_(ij)) and the derived elastic moduli(B, G, E, v). Results indicate that these X_2N_2O(X = C, Si, Ge) compounds are mechanically stable and show the brittle behaviors. The electronic properties of the present compounds are analyzed by using the band structure and density of states. The phonon dispersion calculations imply that the present compounds are dynamically stable. Based on the quasi-harmonic approximation, the calculations of the specific heat indicate that the temperature in a range of 0 K–1500 K and pressure in a range of 0 GPa–40 GPa have a large effect on the thermal quantities of Ge_2N_2O,compared with on those of the C_2N_2O and Si_2N_2O compounds.     

Si3Xn (X=C,O,N;n=1,2)团簇的密度泛函研究

使用密度泛函理论(DFT)的杂化密度泛函B3LYP方法在6-31G*基组水平上对Si3Xn(X=C,O,N;n=1,2)团簇各种可能的构型进行几何结构优化,预测了各团簇的最稳定结构.并对最稳定结构的电子结构、振动特性、成键特性和电荷特性等进行了理论研究.结果表明团簇的几何结构都是平面结构,通常Si3X2出现是Si-X键,较少出现X-X键;而Si3X中出现Si-X键和Si-Si键共存,Si3Xn(X=C,O,N;n=1,2)团簇的电荷布局分布表明这种电荷转移的作用使得团簇中所有X原子呈负电性,Si原子显正电性.处于不同位置的Si原子呈不同大小布局数,而且由于Si3X2的对称性,2个X负电性相同.     

密度泛函理论研究MN@H_2O (M=Ga,Ge, In,Sn, Sb; N=M,Al)团簇的特性

采用密度泛函理论的B3LYP, B3P86, B1B95, P3PW91和PBE1PBE方法结合SDD, LANL2DZ和CEP-121G基组计算了d~(10)组态二聚物MN(M=Ga, Ge, In, Sn和Sb; N=M和Al)的几何结构.采用B3P86/SDD进一步研究了MN@H_2O团簇的几何结构及吸附能.结果表明,水分子结合在二聚物M_2上时,对二聚物影响较大,对水分子自身影响较小.将M_2中Ga, Ge, In, Sn或Sb替换一个原子为Al时,水分子在GeAl和SnAl上的吸附能变化较大,而在GaAl, InAl和SbAl上吸附能变化较小.另外, H_2O吸附在Ga, Ge, In, Sn和Sb上时,与吸附在Al上时,吸附能的变化不大.     

Coadsorption of gold with chlorine on CeO2 (111) surfaces: A first principles study

To investigate the effects of chlorine on the Au/ceria catalysts,the adsorption of gold or chlorine and their coadsorpiton on the stoichiometric and partially reduced CeO₂（111） surfaces are studied from the first principles.It is found that the adsorption of Au is significantly enhanced by the chlorine preadsorption on the stoichiometric CeO₂（111） surface;while on the partially reduced CeO₂（111） surface,the preadsorbed chlorine inhabits the oxygen vacancy（which is the preferred adsorption site for gold）,leading to a CeOCl phase and the dramatical weakening of the Au adsorption.Therefore,chlorine on the CeO₂（111） surface can affect the Au adsorption thus the activity of the Au/CeO₂ catalyst.     

用SAC-CI方法研究Si(CH3)2O双自由基的基态、激发态、阳离子态和阴离子态

采用Nakatsuji提出的对称匹配耦合簇相互作用(SAC-CI)方法,计算了Si(CH3)2O双自由基分子的基态,单重三重激发态,阳离子二重态和阴离子二重态的激发能,光电子谱,电离能等.结果表明,SAC-CI方法比TDDFT有明显优势.     

H2O在SrTiO3-(001)TiO2表面上吸附和解离的密度泛函理论研究

利用密度泛函理论研究了0.25单层(ML),0.5ML,0.75ML和1ML吸附率下H2O在SrTiO3-(001)TiO2表面上的吸附行为.比较了不同吸附率下分子吸附和解离吸附的稳定性,利用微动弹性带(nudged elastic band)方法计算了H2O的解离势垒.结果表明:在低吸附率(0.25ML和0.5ML)时,H2O表现为解离吸附;在0.75ML吸附率下,分子吸附和解离吸附同时存在;而在全吸附(吸附率为1ML)时,分子吸附更稳定.基于对H2O分子与表面之间以及H2O分子之间的电荷转移和相互作用的分析,讨论了吸附率对H2O吸附和解离的影响.     

La调节Pb(Zr,Sn,Ti)O_3反铁电陶瓷的相变与电学性质

利用X射线衍射、弱场介电温度谱、强场极化强度研究了不同La含量(Pb1-xLa2x3)(Zr06Sn03Ti01)O3(000≤x≤012)(PLZSnT)陶瓷的相变与电学特性.实验发现,随La含量增大,室温下材料由铁电三方相(x=000)转变为反铁电四方相(003≤x≤009)和立方相(x=012).介电测试表明,La含量增大,反铁电→顺电相变温度降低,峰值介电常量减小.在x=006的PLZSnT三元相图中,反铁电四方相区扩大到Ti含量约为18at%,该系统反铁电陶瓷具有“窄、斜”型双电滞回线和“三电滞回线”;在高Zr、高Sn区,反铁电→顺电相变呈现弥散相变和介电频率色散特征,即反铁电极化弛豫现象.从ABO3钙钛矿结构的容忍因子(t)和反铁电相的结构特征出发,讨论了La对Pb(Zr,Sn,Ti)O3相变与电学性质的影响机理 关键词： 场诱相变 弛豫型反铁电体 介电性能 La调节Pb(Zr Sn Ti)O3     

Chemical interactions in noncontact AFM on semiconductor surfaces: Si(111), Si(100) and GaAs(110)

Total-energy pseudopotential calculations are used to study the imaging process in noncontact atomic force microscopy (AFM) on Si(111), Si(100) and GaAs(110) surfaces. The chemical bonding interaction between a localised dangling bond on the atom at the apex of the tip and the dangling bonds on the adatoms in the surface is shown to dominate the forces and the force gradients and, hence, to provide atomic resolution. The lateral resolution capabilities are tested in both the Si(100) and the GaAs(110) surfaces. In the first case, the two atoms in a dimer can be resolved due to the dimer flip induced by the interaction with the tip during the scan, while in the GaAs(110), we identify the anion sublattice as the one observed in the experimental images.     

Stability and electronic properties of the O-terminated Cu2O(111) surfaces: First-principles investigation

The effect of different vacancies on the morphology of the O-terminated Cu₂O(111) surface has been studied through the first-principles calculations. Our results show that Cu and O vacancies trigger large relaxations and formation of two different facets. Our emulated STM images are in consistent with the experimental STM patterns. A sizeable magnetic moment (∼1.0 μ_B) was found for surfaces with either Cu or O vacancies. The calculated formation energies of surface vacancies indicate that the deficient surfaces are more stable than the stoichiometric O-terminated (1×1) surface, which is also in line with our results obtained from ab initio atomistic thermodynamics studies.