染料敏化太阳能电池中二聚噻吩类光敏染料构效关系的理论研究

D-π-A型有机光敏染料结构上的微小差异会引起器件性能的显著不同. 为了合理解释染料分子1和2(给体分别为咔唑和二氢吲哚)结构与性能之间的关系, 采用密度泛函理论(DFT)和含时密度泛函理论(TD-DFT)讨论了包括紫外-可见吸收光谱、 光捕获效率、 电子注入驱动力、 垂直方向偶极矩和电子转移数目在内的一系列影响染料性能的理论参数. 结果表明, 在光捕获效率和电子注入效率差别不大的情况下, 染料分子2较低的染料再生效率可导致其短路电流较小; 同时, 在由光诱导产生的从染料分子转移到半导体的电子数目以及电子复合程度相差不大的情况下, 染料分子1垂直方向上较大的偶极矩则可导致其具有较高的开路电压. 计算结果与实验值相吻合, 有望对今后设计合成高效光敏染料提供一定的理论指导.     

Synthesis and Photovoltaic Properties of Non-fullerene Solution Processable Small Molecule Acceptors

Two non-fullerene small molecules, BT-C6 and BT-C12, based on the vinylene-linked benzothiadiazole- thiophene(BT) moiety flanked with 2-(3,5,5-trimethylcyclohex-2-en-1-ylidene)malononitrile have been synthesized and characterized by solution/thin film UV-Vis absorption, photoluminescence(PL), and cyclic voltammetry(CV) measurements. The two molecules show intense absorption bands in a wide range from 300 nm to 700 nm and low optical bandgaps for BT-C6(1.60 eV) and for BT-C12(1.67 eV). The lowest unoccupied molecular orbital(LUMO) levels of both the molecules are relatively higher than that of [6,6]-phenyl C61 butyric acid methyl ester(PCBM), promising high open circuit voltage(V_oc) for photovoltaic application. Bulk heterojunction(BHJ) solar cells with poly(3-hexylthiophene) (P3HT) as the electron donor and the two molecules as the acceptors were fabricated. Under 100 mW/cm² AM 1.5 G illumination, the devices based on P3HT:BT-C6(1:1, mass ratio) show a power conversion efficiency(PCE) of 0.67%, a short-circuit current(J_sc) of 1.63 mA/cm², an open circuit voltage(V_oc) of 0.74 V, and a fill factor(FF) of 0.56.     

Novel organic dye sensitizers containing fluorenyl and biphenyl moieties for solar cells

Three novel triarylamine dyes(AFL1-AFL3) containing fluorenyl and the biphenyl moieties have been designed and synthesized for application in dye-sensitized solar cells.The light-harvesting capabilities and photovoltaic performance of these dyes were investigated systematically through comparison of different π-bridges.The dye with a furan linker exhibited a higher open-circuit voltage(V_(OC)) and monochromatic incident photon-to-current conversion efficiency(IPCE) compared to thiophene and benzene linker.Thus,AFL3 containing a furan linker exhibited the maximum overall conversion efficiency of 5.81%(V_(OC) = 760 mV,J_(SC) = 11.36 mA cm~2 and ff=0.68) under standard global AM 1.5 G solar condition.     

Modulation of photovoltaic behavior of dye-sensitized solar cells by electron donors of porphyrin dyes and cosensitization

Porphyrin dyes have received great attention due to their excellent photovoltaic performance in dyesensitized solar cells(DSSCs). In this work, dyes XC1–XC3 were synthesized by introducing various numbers of bis(4-methoxyphenyl)amino and p-hexyloxyphenyl groups to porphyrin meso-positions.The XC1 molecule contains two p-hexyloxyphenyl groups, and its DSSCs showed the power conversion efficiency of 4.81%. For XC2 and XC3, the replacement of p-hexyloxyphenyl with diphenylamino groups can effectively enhance the light harvesting around 500 nm. However, the highest occupied molecular orbitals(HOMOs) were elevated too much, which suppressed the dye regeneration processes, leading to low cell efficiencies of 2.51% and 1.27% for XC2, and XC3, respectively. To further improve the cell performance, an anthracene derivative C1 was used as the cosensitizer for XC1, which increased both the Jscand Vocvalues, with an improved efficiency of 5.75%.     

Multispectral Plasmon of Anisotropic Core-shell Gold Nanorods@SiO2: Dual-band Absorption Enhancement with Coupling Dye Molecules

Direct evidence of effects of surface plasmon resonance(SPR) of gold nanorods(GNRs) on dual-band light absorption enhancement with coupling dye molecules was reported by introducing gold nanorod@SiO₂(GNR@SiO₂) core-shell nanoparticles into a photoelectric conversion system. GNR with asymmetric shape had unusual anisotropic SPR[transversal surface plasmon resonance(TSPR) and longitudinal surface plasmon resonance(LSPR)]. The excellent SPR of GNR made it a promising candidate as enhancing light absorption material to increase power conversion efficiency(PCE). The PCE was improved nearly 17.2% upon incorporating GNRs, mostly due to the increase in J_sc, while V_oc and FF were unchanged. The improvement was mostly contributed by the SPR of the GNRs with coupling of N719. And there was also a complementary to N719 in visible light range. Therefore, SPR is an effective tool in improving the photocurrent and consequently enhancement of PCE. The TSPR and LSPR effects of GNRs on light harvesting were reflected in the increased monochromatic incident photon-to-electron conversion efficiency(IPCE). We also utilized finite-difference time-domain(FDTD) to investigate the light coupling of GNRs with TiO₂. Compare to the base anode, the IPCE of optimized electrode showed significant improvement and peaks broadening at 500-600 nm and 610-710 nm. We got an increase in overall conversion efficiency from 6.4% to 7.5%.     

Design of an organic chromophore for p-type dye-sensitized solar cells

A successful model for the design of efficient dyes for p-type dye-sensitized solar cells (DSSCs) is presented. As an example, a novel and efficient organic dye containing a triphenylamine chromophore has been synthesized and successfully applied in a p-type DSSC. The highest incident photon-to-current conversion efficiency (IPCE) of 18% in the visible region has been obtained, which is the highest value so far in p-type DSSCs. This is remarkably high, considering that only 600 nm thin NiO mesoporous films were used as p-type DSSC electrodes.     

Hierarchical TiO2 Flower-spheres with Large Surface Area and High Scattering Ability: an Excellent Candidate for High Efficiency Dye Sensitized Solar Cells

Hierarchical TiO₂ flower-spheres assembled from porous nanosheets-stacked of nanoparticles were synthesized by a simple hydrothermal method with one-step. The as-prepared TiO₂ flower-spheres showed a diameter range from 200 nm to 550 nm and a large surface area of 188 m²/g. A double layer photoanode made of P25 nanoparticles and as-prepared TiO₂ flower-spheres was fabricated for the dye sensitized solar cells(DSSCs). The efficient light scattering and dye absorption of the photoanode can be attributed to the top-layer of hierarchical TiO₂ flower-spheres. DSSCs based on the double layers photoanode exhibit a higher energy conversion efficiency of 8.11% with a short-circuit photocurrent density of 17.87 mA/cm², indicating that there is an increase of 38% in the conversion efficiency compared to those based on electrode P25(5.91%, 14.09 mA/cm²).     

Effective design of A-D-A small molecules for high performance organic solar cells via F atom substitution and thiophene bridge

Novel A-D-A-type small molecule donors employ thiophene bridge and F-substitution to improve the power conversion efficiency in organic solar cell.     

Dye-sensitized solar cells based on functionalized truxene structure

Three new metal-free organic dyes(TX1, TX2 and TX3) based on truxene core structure, with triphenylamine as the electron donor, thiophene as the p spacers, and cyanoacetic acid or rhodanine-3-acetic acid as the electron acceptor are designed and synthesized. Their UV–vis absorption spectra,electrochemical and photovoltaic properties were investigated. The cyanoacrylic acid is verified to be a better acceptor unit(meanwhile the anchoring group) compared to the rhodanine-3-acetic acid. And also, two anchoring groups in TX2 could provide stronger adsorption ability on the Ti O2 surface. In addition, the EIS results indicate a slower charge recombination processes for TX2. As a result, dye TX2 bearing two cyanoacetic acid outperforms the other two dyes, exhibiting the photo-conversion efficiency of 2.64%, with Jsc= 5.09 m A cm–2, Voc= 729 m V, FF = 71.1.     

Functionalized organic dyes containing a phenanthroimidazole donor for dye-sensitized solar cell applications

Five functionalized organic dyes (H6-10) containing a phenanthroimidazole unit as an electron donor were synthesized and characterized for use in dye-sensitized solar cell (DSSC) applications. Under standard global AM 1.5 solar conditions, the DSSCs based on dye H6 displayed the best performance, with an incident photon-to-current conversion efficiency (IPCE) exceeding 70% at wavelengths of 400–530 nm, a short-circuit photocurrent density of 10.98 mA cm^?2, an open-circuit voltage of 0.68 V, a fill factor of 0.69, and an overall conversion efficiency of 5.12%. This efficiency is ～94% of that for JK2 cells (5.46%) and ～72% of that for N719 cells (7.07%) under the same conditions.     

电沉积CdTe多晶薄膜光电化学电池的初步研究

采用电沉积工艺,在黄铜衬底上阴极电沉积多晶CdTe薄膜,并用它作为光电极,Cu₂S作为对电极,多硫氧化还原体系Na₂S+NaOH+S溶液为电解液制作光电化学电池,测量电池的J_sc、V_oc和I～V特性曲线并计算了效率和填充因子F_F,对影响电池效率的几种因素作了关联和讨论。     

Near infrared thieno[3,4-b]pyrazine sensitizers for efficient quasi-solid-state dye-sensitized solar cells

Three near infrared (NIR) metal-free organic sensitizers (FNE32, FNE34, FNE36) based on the thieno[3,4-b]pyrazine derivative have been designed and synthesized for application in quasi-solid-state dye-sensitized solar cells (DSSCs). These organic dyes demonstrate maximum absorption bands at 596-625 nm due to the presence of the thieno[3,4-b]pyrazine derivative, which facilitates the intramolecular electron transfer from the donor to the acceptor. Quasi-solid-state DSSCs based on FNE34 display efficient photoelectric conversion over the whole visible range extending into the NIR region up to 900 nm with maximum incident monochromatic photon-to-electron conversion efficiency (IPCE) of 77%, yielding a short-circuit photocurrent density of 16.24 mA cm(-2) and a power conversion efficiency of 5.30%. To the best of our knowledge, this is the highest efficiency for quasi-solid-state DSSCs based on an organic NIR dye. When exposed to one-sun illumination for 1000 h, the quasi-solid-state DSSC based on FNE34 exhibits good long-term stability with almost constant power conversion efficiency.     

聚乙烯吡咯烷酮基碘凝胶电解质的制备及在染料敏化太阳能电池中的应用

采用聚乙烯吡咯烷酮(PVP)和聚偏氟乙烯(PVDF)为凝胶剂, 以碘化锂和碘单质为碘源, 碳酸乙烯酯(EC)和碳酸丙烯酯(PC)为溶剂, 制备了染料敏化太阳能电池(DSSCs)用凝胶聚合物电解质(GPE). 使用拉曼光谱、 循环伏安曲线和交流阻抗谱等对GPE进行表征. 结果表明, 聚合物的配比与浓度及碘与碘化锂比例对该电解质性能有很大影响, 当聚合物质量分数为10%、 PVP与PVDF质量比为80∶20、 I₂浓度为0.042 mol/L且LiI与I₂摩尔比为30∶1时, 制备的GPE在室温下电导率达最大值(3.27 mS/cm). 使用该GPE组装的DSSCs在100 mW/cm²的模拟太阳光照射下, 开路电压为0.64 V, 短路电流为13.6 mA/cm², 填充因子为0.595, 能量转化效率为5.18%, 并在30 d内表现出了良好的稳定工作性能.     

Enhanced performance of ruthenium dye-sensitized solar cell by employing an organic co-adsorbent of N,N'-bis((pyridin-2-yl)(methyl) methylene)-o-phenylenediamine

A pyridine-anchor co-adsorbent of N,N'-bis((pyridin-2-yl)(methyl) methylene)-o-phenylenediamine(named BPPI) is prepared and employed as co-adsorbent in dye-sensitized solar cells(DSSCs). The prepared co-adsorbent could overcome the deficiency of N719 absorption in the low wavelength region of visible spectrum, offset competitive visible light absorption of I₃^-, enhance the spectral responses of the co-adsorbed TiO₂ film in region from 300 nm to 750 nm, suppress charge recombination, prolong electron lifetime, and decrease the total resistance of DSSCs. The optimized cell device co-sensitized by BPPI/N719 dye gives a short circuit current density of 12.98 mA cm^-2, an open circuit voltage of 0.73 V, and a fill factor of 0.66 corresponding to an overall conversion efficiency of 6.22% under standard global AM 1.5 solar irradiation, which is much higher than that of device solely sensitized by N719(5.29%) under the same conditions. Mechanistic investigations are carried out by various spectral and electrochemical characterizations.     

2D-π-A Type Organic Dyes Based on N,N-Dimethylaryl Amine and Rhodamine-3-acetic Acid for Dye-sensitized Solar Cells

Three organic dyes XS17 – 19 based on N,N‐dimethylaryl amine and rhodamine‐3‐acetic acid moieties are designed and synthesized. These dyes were applied into nanocrystalline TiO₂ dye‐sensitized solar cells through standard operations, showing strong absorption bands at around 320–650 nm, and exhibiting broad IPCE responses. Cell based on XS17 gave a J_sc of 3.7 mA/cm², an open circuit voltage of 550 mV, and a fill factor of 0.68, corresponding to an overall conversion efficiency of 1.4%. The low overall conversion efficiency is due to the modest IPCE and V_oc values, which mainly stem from the acceptor of rhodanine‐3‐acetic acid.     

Ethoxy‐substituted Oligo‐phenylenevinylene‐Bridged Organic Dyes for Efficient Dye‐Sensitized Solar Cells

Organic dyes with ethoxy‐substituted oligo‐phenylenevinylene as chromophores were synthesized for dye‐sensitized solar cells (DSSCs), and the detailed relationships between the dye structures, photophysical properties, electrochemical properties, and performances of DSSCs were described. The dye S3O showed broad IPCE spectra in the spectral range of 350–750 nm, and the dye S1P showed solar energy‐to‐electricity conversion efficiency (() of up to 4.23% under AM 1.5 irradiation (100 mW/cm²) in comparison with the reference Ru‐complex (N719 dye) with an η value of 5.90% under similar experimental conditions.     

Structural engineering of dipolar organic dyes with an electron-deficient diphenylquinoxaline moiety for efficient dye-sensitized solar cells

A series of new organic dyes containing an electron-deficient diphenylquinoxaline moiety was synthesized and employed as the photosensitizers in dye-sensitized solar cells (DSSCs). The multiple phenyl rings in the peripheral positions of the dye structure provide a hydrophobic barrier to slow down the charge recombination. The photophysical and electrochemical properties of these dyes were investigated in detail. The cell performance and the associated photophysical and electrochemical properties can be easily tuned by the modification of the aromatic fragments within the π spacer. Dye CR204-based DSSC reached the best energy conversion efficiency of 6.49% with an open-circuit voltage of 666 mV, a short-circuit photocurrent density of 14.9 mA cm⁻², and a fill factor of 0.66. The IPCE of CR204-based DSSC covers the light-harvesting to NIR region.     

Dye‐Sensitized Solar Cells Based on a Donor–Acceptor System with a Pyridine Cation as an Electron‐Withdrawing Anchoring Group

New hemicyanine dyes ( CM101 , CM102 , CM103 , and CM104 ) in which tetrahydroquinoline derivatives are used as electron donors and N‐(carboxymethyl)‐pyridinium is used as an electron acceptor and anchoring group were designed and synthesized for dye‐sensitized solar cells (DSSCs). Compared with corresponding dyes that have cyanoacetic acid as the acceptor, N‐(carboxymethyl)‐pyridinium has a stronger electron‐withdrawing ability, which causes the absorption maximum of dyes to be redshifted. The photovoltaic performance of the DSSCs based on dyes CM101 – CM104 markedly depends on the molecular structures of the dyes in terms of the n‐hexyl chains and methoxyl. The device sensitized by dye CM104 achieved the best conversion efficiency of 7.0 % (J_sc=13.4 mA cm^?2, V_oc=704 mV, FF=74.8 %) under AM 1.5 irradiation (100 mW cm^?2). In contrast, the device sensitized by reference dye CMR104 with the same donor but the cyanoacetic acid as the acceptor gave an efficiency of 3.4 % (J_sc=6.2 mA cm^?2, V_oc=730 mV, FF=74.8 %). Under the same conditions, the cell fabricated with N719 sensitized porous TiO₂ exhibited an efficiency of 7.9 % (J_sc=15.4 mA cm^?2, V_oc=723 mV, FF=72.3 %). The dyes CM101 – CM104 show a broader spectral response compared with the reference dyes CMR101 – CMR104 and have high IPCE exceeding 90 % from 450 to 580 nm. Considering the reflection of sunlight, the photoelectric conversion efficiency could be almost 100 % during this region.     

Oligothiophene-containing coumarin dyes for efficient dye-sensitized solar cells

We have developed oligothiophene-containing coumarin dyes fully functionalized for dye-sensitized nanocrystalline TiO(2) solar cells (DSSCs). DSSCs based on the dyes gave good performance in terms of incident photon-to-current conversion efficiency (IPCE) in the range of 400-800 nm. A solar energy-to-electricity conversion efficiency (eta) of 7.4% was obtained with a DSSC based on 2-cyano-3-[5'-(1,1,6,6-tetramethyl-10-oxo-2,3,5,6-tetrahydro-1H,4H,10H-11-oxa-3a-aza-benzo[de]anthracen-9-yl)-[2,2']bithiophenyl-5-yl]acrylic acid (NKX-2677) under simulated AM 1.5G irradiation (100 mW cm(-2)) with a mask: short-circuit current density (J(sc)) = 13.5 mA cm(-2); open-circuit voltage (V(oc)) = 0.71 V; fill factor (FF) = 0.77. Transient absorption spectroscopy measurements indicated that electron injection from NKX-2677 to the conduction band of TiO(2) is very rapid (<100 fs), which is much faster than the emission lifetime of the dye (1.0 ns), giving a highly efficient electron injection yield of near unity.     

Additive-free non-fullerene organic solar cells with random copolymers as donors over 9% power conversion efficiency

The PBDB-TBT1:ITIC-based device obtains PCE of 9.09%, and is insensitive to additive and thermal annealing, and forms microstructural morphology.