Li4Ti5O12/CMK-3复合材料的制备及其作为锂离子电池负极材料的性能

将LiNO₃和Ti(OC₄H₉)₄填填充在有序介孔碳CMK-3 孔道中, 然后烧结合成了Li₄Ti₅O₁₂/CMK-3复合材料. 利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射(XRD)对其结构和微观形貌进行了表征. 利用差热-热重分析(TG-DTA)测试复合材料中Li₄Ti₅O₁₂的含量. 利用充放电测试、循环伏安和电化学阻抗技术考察了复合材料作为锂离子电池负极材料的性能. 发现Li₄Ti₅O₁₂分布在CMK-3孔道中及其周围, 复合材料的高倍率充放电性能显著优于商品Li₄Ti₅O₁₂, 复合材料中Li₄Ti₅O₁₂的比容量明显高于除去CMK-3的样品(在1C倍率时比容量为117.8 mAh·g^-1), 其0.5C、1C和5C倍率的放电比容量分别为160、143 和131 mAh·g^-1, 库仑效率接近100%, 5C倍率时循环100次的容量损失率只有0.62%. 本研究结果表明CMK-3明显提高了Li₄Ti₅O₁₂的高倍率充放电性能, 可能是CMK-3特殊的孔道结构和良好的导电性减小了Li₄Ti₅O₁₂的粒径并提高了其电导率.     

锂离子电池负极材料Li_(4-x)K_xTi_5O_(12)结构和电化学性能

采用固相反应的方法制备了尖晶石型Li4Ti5O12和K掺杂Li4-xKxTi5O12(x=0.02,0.04,0.06)。通过XRD、SEM、BET等对制备材料进行了分析。结果表明,K掺杂没有影响立方尖晶石型Li4Ti5O12的合成,同时也没有改变Li4Ti5O12的电化学反应过程。K掺杂Li4-xKxTi5O12具有比Li4Ti5O12小的颗粒粒径和比Li4Ti5O12大的比表面积、孔容积。适量的K掺杂能够明显改善Li4Ti5O12的电化学性能,尤其是倍率性能,但是过多的K掺杂却不利于材料电化学性能的提高。研究表明,Li3.96K0.04Ti5O12体现了相对较好的倍率性能和循环稳定性。0.5C下,首次放电比容量为161mAh·g-1,3.0和5.0C下,容量保持分别为138和121mAh·g-1。3.0C下,200次循环后容量保持为137mAh·g-1。     

Preparation and characterization of Li4/3Ti5/3O4/Ag composite prepared by sol-gel technique

The powders of Li_4/3Ti_5/3O₄/Ag composite were prepared by sol-gel technique. Structural identification, surface morphology and electrochemical properties of the powders were studied by X-ray diffraction, scanning electron microscopy and galvanostatic charge-discharge experiments. The results show that Li_4/3Ti_5/3O₄/Ag composite derived from sol-gel is a composite of Li_4/3Ti_5/3O₄ and silver. Li_4/3Ti_5/3O₄/Ag composite shows higher specific capacity, higher columbic efficiency and lower polarization than Li_4/3Ti_5/3O₄. The addition of silver greatly improves the cycleability of Li_4/3Ti_5/3O₄, especially at higher charge-discharge rate.     

Preparation and characterization of LiMn2O4/Li1.3Al0.3Ti1.7(PO4)3/LiMn2O4 thin-film battery by spray technique

Solid-state thin-film lithium-ion battery of LiMn₂O₄/Li_1.3Al_0.3Ti_1.7(PO₄)₃/LiMn₂O₄ is prepared by spray technique using Li_1.3Al_0.3Ti_1.7(PO₄)₃ sintered pellet as both electrolyte and substrate. The thin-film battery is heat-treated by rapid thermal annealing. Phase identification, morphology and electrochemical properties of the sintered pellets and thin-film battery are investigated by X-ray diffraction, scanning electron microscopy, electrochemical impedance spectroscopy, cyclic voltammetry, and galvanostatic charge-discharge experiments, respectively. The results show that LiMn₂O₄ films with some pores are well deposited on the surface of Li_1.3Al_0.3Ti_1.7(PO₄)₃ sintered pellet. The discharge current density and temperature have considerable effect on discharge capacity of the thin-film battery. LiMn₂O₄/Li_1.3Al_0.3Ti_1.7(PO₄)₃/LiMn₂O₄ thin-film battery can be easily cycled with a capacity loss of 0.213% per cycle when 50 cycles are carried out.     

LiMn2O4表面包覆Li4Ti5O12的制备及倍率特性

采用固相法合成了尖晶石型LiMn₂O₄，并通过溶胶-凝胶法制备了不同物质的量的百分比含量Li₄Ti₅O₁₂包覆的正极材料。X-射线衍射和扫描电镜结果表明，Li₄Ti₅O₁₂微粒包覆在LiMn₂O₄的表面没有产生晶体结构的变化。实验电池在室温下，以1C，2C和5C倍率作充放电循环测试；结果表明，与未包覆的LiMn₂O₄相比，表面包覆Li₄Ti₅O₁₂微粒的正极材料在高倍率下具有更好的循环稳定性。     

Li4Ti5O12/(Cu+C)复合材料的制备及电化学性能

以Li₄Ti₅O₁₂,Cu(CH₃COO)₂·H₂O和C₆H₁₂O₆为前驱体,化学沉积与热分解结合合成锂离子电池负极材料Li₄Ti₅O₁₂/(Cu+C)。采用X-射线衍射(XRD)、扫描电子显微镜(SEM)、恒流充放电、循环伏安和电化学阻抗方法表征样品的结构、形貌和电化学性能。结果表明,Li₄Ti₅O₁₂表面包覆的Cu与C提高了Li₄Ti₅O₁₂电极材料的导电率,其循环性能和倍率性能得到有效地改善。在0.5C、1C和3C倍率下,经过50次充放电循环,放电比容量分别为168.2、160、140.6 mAh·g^-1,其容量保持率分别为88.7%、84.4%、71.2%。电化学阻抗测试表明,表面包覆的Cu与C使其电荷转移阻抗大幅度减少。     

Li4Ti5O12/(Ag+C)电极材料的固相合成及电化学性能

以Li₂CO₃,TiO₂为原料,葡萄糖为碳源,采用固相煅烧工艺合成了亚微米级的Li₄Ti₅O₁₂/C复合负极材料。并将之与AgNO₃复合,采用固相方法制备出了Ag表面修饰的Li₄Ti₅O₁₂/(Ag+C)复合材料。采用XRD、SEM和TEM测试方法对材料的微结构进行了表征。结果表明,C的存在对Ag单质在Li₄Ti₅O₁₂/C颗粒表面的大量形成起到了积极的促进作用,从而很大程度地提高了Li₄Ti₅O₁₂/C的电导率,因此有效地改善了其电化学性能。在1C倍率下,Li₄Ti₅O₁₂/(Ag+C)复合材料的首次放电容量达到了164 mAh·g^-1。     

高倍率尖晶石型Li_4Ti_5O_(l2)/TiN锂离子电池负极材料的合成及其电化学性能

以乙酰丙酮(ACAC)为螯合剂、聚乙二醇(PEG)为分散剂,采用溶胶-凝胶法合成了尖晶石型Li4Ti5Ol2/TiN材料.考察了TiN膜对尖晶石型Li4Ti5Ol2锂离子电池负极材料电化学性能的影响.利用X射线光电子能谱(XPS)对Li4Ti5O12表面的TiN膜进行了分析.X射线衍射(XRD)和扫描电子显微镜(SEM)分析表明,Li4Ti5Ol2/TiN材料为结晶良好的亚微米纯相尖晶石型钛酸锂.电化学性能测试表明,该材料的首次放电比容量为173.0mAh·g-1,并且具有良好的循环性能,以0.2C、1C、2C、5C倍率放电进行测试,10次循环后比容量分别为170.6、147.6、135.6、111.0mAh·g-1,较之表面无TiN膜的钛酸锂材料表现出更好的倍率特性.循环伏安曲线(CV),交流阻抗图谱(EIS)进一步论证了TiN膜改善了尖晶石型Li4Ti5Ol2锂离子电池负极材料的电化学性能.     

Preparation of Li4Ti5O12 Microspheres with a Pure Cr2O3 Coating Layer and its Effect for Lithium Storage

The pure Cr₂O₃ coated Li₄Ti₅O₁₂ microspheres were prepared by a facile and cheap solutionbased method with basic chromium(III) nitrate solution (pH=11.9). And their Li-storage properties were investigated as anode materials for lithium rechargeable batteries. The pure Cr₂O₃ works as an adhesive interface to strengthen the connections between Li₄Ti₅O₁₂ particles, providing more electric conduction channels, and reduce the inter-particle resistance. Moreover, LixCr₂O₃, formed by the lithiation of Cr₂O₃, can further stabilize Li₇Ti₅O₁₂ with high electric conductivity on the surface of particles. While in the acid chromium solution (pH=3.2) modification, besides Cr₂O₃, Li₂CrO₄ and TiO₂ phases were also found in the final product. Li₂CrO₄ is toxic and the presence of TiO₂ is not welcome to improve the electrochemical performance of Li₄Ti₅O₁₂ microspheres. The reversible capacity of 1% Cr₂O₃-coated sample with the basic chromium solution modification was 180 mAh/g at 0.1 C, and 134 mAh/g at 10 C. Moreover, it was even as high as 127 mAh/g at 5 C after 600 cycles. At-20℃, its reversible specific capacity was still as high as 118 mAh/g.     

Li ion diffusion in Li4Ti5O12 thin film electrode prepared by PVP sol-gel method

Li₄Ti₅O₁₂ thin films for rechargeable lithium batteries were prepared by a sol-gel method with poly(vinylpyrrolidone). Interfacial properties of lithium insertion into Li₄Ti₅O₁₂ thin film were examined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and potentiostatic intermittent titration technique (PITT). Redox peaks in CV were very sharp even at a fast scan rate of 50 mV s⁻¹, indicating that Li₄Ti₅O₁₂ thin film had a fast electrochemical response, and that an apparent chemical diffusion coefficient of Li⁺ ion was estimated to be 6.8×10⁻¹¹ cm² s⁻¹ from a dependence of peak current on sweep rates. From EIS, it can be seen that Li⁺ ions become more mobile at 1.55 V vs. Li/Li⁺, corresponding to a two-phase region, and the chemical diffusion coefficients of Li⁺ ion ranged from 10⁻¹⁰ to 10⁻¹² cm² s⁻¹ at various potentials. The chemical diffusion coefficients of Li⁺ ion in Li₄Ti₅O₁₂ were also estimated from PITT. They were in a range of 10⁻¹¹-10⁻¹² cm² s⁻¹.     

三维连续结构Li4Ti5O12/石墨烯纳米复合材料：制备和其锂离子电池超长循环性能

利用具有三维连续纳米孔结构的热剥离石墨烯为骨架制备Li4Ti5O12/石墨烯纳米复合材料。通过乙醇挥发法在热剥离石墨烯的纳米孔道内引入前驱物,进一步高温热处理,在热剥离石墨烯的孔道内原位形成Li4Ti5O12纳米粒子。利用复合材料作为锂离子电池电极材料。电化学反应过程中,热剥离石墨烯的三维连续结构确保了Li4Ti5O12纳米粒子与石墨烯在长循环过程中的有效接触。因此,复合材料表现出优异的循环稳定性。在5C下,5 000次循环后,其容量保持率高达94%。     

Effect of Nb-doping on electrochemical stability of Li4Ti5O12 discharged to 0?V

Li₄Ti_4.95Nb_0.05O₁₂ is synthesized by a citric acid-assistant sol–gel method. X-ray diffraction (XRD) reveals that highly crystalline Li₄Ti_4.95Nb_0.05O₁₂ without any impurity is obtained. The electrochemical performances of the Li₄Ti_4.95Nb_0.05O₁₂ and the Li₄Ti₅O₁₂ in the range from 0 to 2.5 V are investigated. The Li₄Ti_4.95Nb_0.05O₁₂ presents a higher specific capacity and better cycling stability than the Li₄Ti₅O₁₂ due to the improved conductivity. The Li₄Ti_4.95Nb_0.05O₁₂ exhibits a capacity as high as 231.2 mAh g⁻¹ after 100 cycles, which is much higher than the Li₄Ti₅O₁₂ (111.1 mAh g⁻¹). The effect of Nb-doping on electrochemical performance of Li₄Ti₅O₁₂ discharged to 0 V has also been discussed.     

Synthesis and electrochemical performances of Li4Ti4.95Zr0.05O12/C as anode material for lithium-ion batteries

Spinel Li₄Ti_5 − x Zr _x O₁₂/C (x = 0, 0.05) were prepared by a solution method. The structure and morphology of the as-prepared samples were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The electrochemical performances including charge–discharge (0–2.5 V and 1–2.5 V), cyclic voltammetry, and ac impedance were also investigated. The results revealed that the Li₄Ti_4.95Zr_0.05O₁₂/C had a relatively smaller particle size and more regular morphology than that of Li₄Ti₅O₁₂/C. Zr⁴⁺ doping enhanced the ability of lithium-ion diffusion in the electrode. It delivered a discharge capacity 289.03 mAh g⁻¹ after 50 cycles for the Zr⁴⁺-doped Li₄Ti₅O₁₂/C while it decreased to 264.03 mAh g⁻¹ for the Li₄Ti₅O₁₂/C at the 0.2C discharge to 0 V. Zr⁴⁺ doping did not change the electrochemical process, instead enhanced the electronic conductivity and ionic conductivity. The reversible capacity and cycling performance were effectively improved especially when it was discharged to 0 V.     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.     

Effects of carbon coating from sucrose and PVDF on electrochemical performance of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/C composites in different potential ranges

The carbon coated nanoflower-like Li₄Ti₅O₁₂/C composites were prepared via hydrothermal method followed by surface modification using sucrose or polyvinylidene fluoride (PVDF) as carbon sources. X-ray diffraction, SEM, TEM, Raman spectroscopy, TGA, and the electrochemical measurements were used for the materials characterization. Such modification leads to the formation of a high-conductive carbon coating. In the case of polyvinylidene fluoride use, fluorination of Li₄Ti₅O₁₂ surface takes place also. As a result, electrochemical performance of the obtained composites is improved. In the potential range of 1–3 V, Li₄Ti₅O₁₂, Li₄Ti₅O₁₂/C_PVDF, and Li₄Ti₅O₁₂/C_sucrose exhibit, respectively, the discharge capacities of 142.5, 154.3, and 170.4 mAh/g at a current of 20 mA/g and 57.2, 82.1, and 89.3mAh/g at a current of 3200 mA/g. When cycled in a potential range of 0.01–3 V, the discharge capacity of Li₄Ti₅O₁₂/C_PVDF increases up to 252 mAh/g at 20 mA/g.     

Sol–gel preparation and electrochemical properties of La-doped Li4Ti5O12 anode material for lithium-ion battery

A sol–gel method using Ti(OC₄H₉)₄, LiCH₃COO·2H₂O, and La(NO₃)₃·6H₂O as starting materials and ethyl acetoacetate as chelating agent to prepare pure and lanthanum (La)-doped Li₄Ti₅O₁₂ is reported. The structure and morphology of the active materials characterized by powder X-ray diffraction and scanning electron microscopy analysis indicate that doping with a certain amount of La³⁺ does not affect the structure of Li₄Ti₅O₁₂, but can restrain the agglomeration of the particles during heat treatment. The electrochemical properties measured by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge cycling tests show that La-doped Li₄Ti₅O₁₂ presents a much improved electrochemical performance due to a decrease in charge transfer resistance. At current densities of 1 and 5 C, the La-doped Li₄Ti₅O₁₂ exhibits excellent reversible capacities of 156.16 and 150.79 mAh?g^?1, respectively. The excellent rate capability and good cycling performance make La-doped Li₄Ti₅O₁₂ a promising anode material for lithium-ion batteries in energy storage systems.     

Preparation of Li4Ti5O12 Yolk–Shell Powders by Spray Pyrolysis and their Electrochemical Properties

We have reported for the first time the preparation of yolk–shell‐structured Li₄Ti₅O₁₂ powders for use as anode materials in lithium‐ion batteries. One Li₄Ti₅O₁₂ yolk–shell‐particle powder is directly formed from each droplet containing lithium, titanium, and carbon components inside the hot wall reactor maintained at 900 °C. The precursor Li₄Ti₅O₁₂ yolk–shell‐particle powders, which are directly prepared by spray pyrolysis, have initial discharge and charge capacities of 155 and 122 mA h g^?1, respectively, at a current density of 175 mA g^?1. Post‐treatment of the yolk–shell‐particle powders at temperatures of 700 and 800 °C improves the initial discharge and charge capacities. The initial discharge capacities of the Li₄Ti₅O₁₂ powders with a yolk–shell structure and a dense structure post‐treated at 800 °C are 189 and 168 mA h g^?1, respectively. After 100 cycles, the corresponding capacities are 172 and 152 mA h g^?1, respectively (retentions of 91 and 90 %).     

Heat capacity and thermodynamic properties of ramsdellite,Li2Ti3O7, and spinel,Li43Ti53O4

The heat capacity and heat content Li_{$\text{4}\text{3}$}Ti_{$\text{5}\text{3}$}O₄ and Li₂Ti₃O₇ have been measured in the temperature range 198—960 K. The lattice and dilation contributions to the heat capacity have been estimated. The standard thermodynamic functions and the high temperature enthalpy and entropy have been derived. The lattice heat capacity of Li_{$\text{4}\text{3}$}Ti_{$\text{5}\text{3}$}O₄ spinel appears to be consistent with the phonon model put forward by Grimes.     

Mesoporous Spherical Li4Ti5O12 as High‐Performance Anodes for Lithium‐Ion Batteries

Porous microspherical Li₄Ti₅O₁₂ aggregates (LTO‐PSA) can be successfully prepared by using porous spherical TiO₂ as a titanium source and lithium acetate as a lithium source followed by calcinations. The synthesized LTO‐PSA possess outstanding morphology, with nanosized, porous, and spherical distributions, that allow good electrochemical performances, including high reversible capacity, good cycling stability, and impressive rate capacity, to be achieved. The specific capacity of the LTO‐PSA at 30 C is as high as 141 mA h g^?1, whereas that of normal Li₄Ti₅O₁₂ powders prepared by a sol–gel method can only achieve 100 mA h g^?1. This improved rate performance can be ascribed to small Li₄Ti₅O₁₂ nanocrystallites, a three‐dimensional mesoporous structure, and enhanced ionic conductivity.     

Solvothermal Synthesis of Superfine Li1−xMn2O4−σ Powders

Superfine Li_1−xMn₂O_4−σ powders were successfully synthesized by the alcohol-thermal method using 0.01 mol of MnO₂, 0.01mol of LiOH·H₂O, and 0.06mol of NaOH as starting materials at 160-200°C. The products are characterized by XRD, TEM, ED, BET, and ICP. Results show that the Li_0.74Mn₂O_3.74 powder prepared at 200°C has an average size of 180 nm with BET surface areas of 16.44 m²/g. A possible formation mechanism is proposed. It was concluded that the alcohol acts not only as the solvent but also as the reducing agent in the synthesis of Li_1−xMn₂O_4−σ powders. The effects of reaction temperature and the contents of NaOH and LiOH on the formation of single phase Li_1−xMn₂O_4−σ were investigated.