石墨烯薄膜的光化学还原制备与表征

采用光化学还原方法制备了图案化的石墨烯薄膜.研究了光还原氧化石墨烯薄膜(PRGO)的热稳定性和发光性质.热重分析(TGA)结果表明,光化学还原主要引起氧化石墨烯(GO)氧化基团的减少,而对GO内水含量影响较小;发光(PL)测试结果表明,不同激发条件下,PRGO的发光与GO相比表现出了不同的变化规律:在波长514 nm的光激发下,PRGO的发光强度比GO明显降低,同时伴随着发光峰峰位红移;而在波长830 nm的光激发下,PRGO的发光强度比GO略有增强,并且发光峰峰位无明显变化,此结果表明不同尺寸的碳团簇局域态(sp2C团簇)的光还原反应活性不同,这与GO特殊的能带结构密切相关.     

氧化石墨烯的可控还原及结构表征

采用氧化还原法, 通过控制还原时间制备了不同还原程度的石墨烯; 用红外光谱、 紫外光谱、 拉曼光谱、 X射线衍射、 热重分析、 电导率测量等多种手段系统研究了不同还原程度石墨烯的结构与性能; 采用透射电子显微镜、 扫描电子显微镜和原子力显微镜比较了氧化石墨烯和石墨烯的形貌. 结果表明, 随着还原程度的增加, 石墨烯中含氧基团减少, 紫外吸收峰逐渐红移, D带与G带的强度比增加, 热稳定性和导电性提高. 微观结构表征说明石墨烯比氧化石墨烯片的厚度增加, 褶皱增多.     

正丁基氯化镁还原氧化石墨烯的表征

采用元素分析、红外光谱(FTIR)、X射线光电子能谱(XPS)、拉曼光谱、X射线衍射(XRD)、固体¹³C核磁共振波谱(¹³C MAS NMR)、热失重分析(TGA)、导电率测试以及原子力显微镜(AFM)等手段对正丁基氯化镁还原的氧化石墨烯进行了系统的表征. 结果表明, 正丁基氯化镁可以有效还原氧化石墨烯, 随着其用量的增加, 氧化石墨烯还原程度增加, 碳/氧摩尔比升高, 片层间距减小, 热稳定性增强, 导电率增大(可达3.6×10² S/m). 还原后部分氧化石墨烯片层发生聚集.     

A Green Synthesis of Substituted Coumarins Using Nano Graphene Oxide as Recyclable Catalyst

One‐pot synthesis of some pyranocoumarins and biscoumarins using graphene oxide nanosheets as efficient catalyst has been investigated. The green methods offer appealing attributes such as excellent yields, short reactions times, use of a safe and recyclable catalyst, and a simple workup procedure.     

Determination of Sudan I Using Electrochemically Reduced Graphene Oxide

Electrochemically reduced graphene oxide (ER-GO) was prepared by reducing exfoliated graphene oxide sheets on a glassy carbon electrode (GCE). The voltammetric responses of Sudan I-IV were studied at the ER-GO modified GCE (ER-GO/GCE). Compared with chemically reduced graphene oxide (CR-GO) modified electrode (CR-GO/GCE), ER-GO/GCE showed higher voltammetric responses to Sudan I. The electrode had a linear response to Sudan I in the range of 0.04–8.0 µmol L^?1 and a detection limit of 0.01 µmol L^?1. The real sample determination indicated that the proposed method was reliable, effective, and sufficient.     

石墨烯-氧化钨复合薄膜的制备及界面电子传输特性

以偏钨酸铵为钨源、聚乙烯吡咯烷酮为连接剂,采用浸渍提拉法制备了石墨烯-氧化钨复合薄膜,利用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)及Raman光谱等方法对复合结构材料进行了表征,并利用光电流测试、交流阻抗谱(EIS)、瞬态光电流谱和强度调制光电流谱等方法,研究复合薄膜电极在光电作用下界面上的载流子转移过程和电荷传输行为.结果表明,组成薄膜的氧化钨纳米颗粒与石墨烯充分复合,光电性能显著提高;与石墨烯复合后,薄膜的瞬态时间常数增大,电子-空穴对寿命延长;电子传输时间减少,为纯氧化钨薄膜的47.5%.     

石墨烯-氧化钨复合薄膜的制备及界面电子传输特性

以偏钨酸铵为钨源、聚乙烯吡咯烷酮为连接剂,采用浸渍提拉法制备了石墨烯-氧化钨复合薄膜,利用X射线衍射（XRD）、扫描电镜（SEM）、透射电镜（TEM）及Raman光谱等方法对复合结构材料进行了表征,并利用光电流测试、交流阻抗谱（EIS）、瞬态光电流谱和强度调制光电流谱等方法,研究复合薄膜电极在光电作用下界面上的载流子转移过程和电荷传输行为. 结果表明,组成薄膜的氧化钨纳米颗粒与石墨烯充分复合,光电性能显著提高;与石墨烯复合后,薄膜的瞬态时间常数增大,电子-空穴对寿命延长;电子传输时间减少,为纯氧化钨薄膜的47.5%.     

Electrical Conductivity of Alkaline-reduced Graphene Oxide

A green route using a very simple and straightforward ultrasonic process under alkaline conditions, rather than a general chemical reduction process using hydrazine, was utilized to obtain the hydrophilic reduced graphene oxide(RGO) sheets, via removing oxygen functional groups from graphene oxide(GO) and repairing the aromatic structure. It is found that the conductivity of the obtained RGO could be tuned by changing pH value in alkaline solution, and the current-voltage(I-V) curves of both GO and RGO are nonlinear and slightly asymmetric. Under the same applied voltage, the current of RGO is much larger than that of GO, indicating a pronounced increase in the electrical conductivity of RGO, compared to that of GO.     

自由基反应诱导的溴功能化还原氧化石墨烯的制备

以氧化石墨烯(GO)为原料,N-溴代丁二酰亚胺(NBS)为溴代试剂,硫代硫酸钠为还原剂,通过羧基化、溴化和还原三步法,采用自由基反应的方式制备了溴功能化还原氧化石墨烯(rGOBr).通过X射线衍射、扫描电子显微镜、红外光谱、拉曼光谱以及X射线光电子能谱等手段对rGOBr的结构、微观形貌和元素组成进行了表征.结果表明,溴元素以共价键的形式分布在石墨烯表面.本方法原料来源广泛、操作简单且条件温和,为石墨烯的溴功能化提供了一条新途径.     

电化学法制备部分还原氧化石墨烯薄膜及其光电性能

提供了一种快速制备氧化石墨烯(GO)薄膜的方法, 并通过调节GO薄膜的含氧量来调控其能级结构.采用阳极电泳及阴极电化学还原联用的方法在F掺杂SnO₂(FTO)导电玻璃上制备出不同层数及含氧量的GO薄膜, 并通过扫描电镜(SEM)、X射线衍射(XRD)、紫外可见(UV-Vis)光谱、X射线光电子能谱(XPS)、拉曼光谱及电化学分析对样品进行表征. 用20-350 s 不同时间电泳沉积得到层数约为77-570层的GO薄膜. 经过不同时间阴极还原的GO薄膜的禁带宽度为1.0-2.7 eV, 其导带位置及费米能级也随之改变. GO作为p型半导体, 与FTO导电膜之间会形成p-n 结, 在光强为100 mW·cm^-2的模拟太阳光照射下, 电泳300 s 且电化学还原120 s时GO薄膜阳极光电流密度达到5.25×10^-8 A·cm^-2.     

石墨烯氧化物薄膜电极的光电化学特性

采用浸渍-提拉法制备了一系列石墨烯氧化物(GO)薄膜,并通过X射线衍射(XRD),扫描电镜(SEM),傅里叶变换红外光谱,紫外-可见吸收光谱和光电化学测量等技术对样品进行了表征.在GO电极上观察到阴极光电流,且光电流密度受薄膜的厚度影响.GO薄膜电极厚度为27nm时,光电流密度为0.25μA·cm-2.此外,GO电极的光电响应还受紫外光照影响,随着紫外光照时间的延长,阴极光电流逐渐减小.该工作提供了简便的通过控制薄膜厚度或紫外光照时间来控制GO薄膜半导体光电化学性能的方法.     

还原氧化石墨烯改性少层剥离石墨增强石墨基钾离子电池负极稳定性

钾在石墨中嵌入电位较低,因此石墨负极可使钾离子电池具有较高的能量密度,是一种理想的钾离子电池负极材料。然而,石墨嵌钾后的体积膨胀率高达60%,导致钾离子电池的循环稳定性较差。此外,钾嵌入石墨层间的动力学过程缓慢,制约了钾离子电池倍率性能的提升。在本工作中,我们用还原氧化石墨烯(rGO)包覆剥离石墨(EG),得到一种具有协同效应的层状复合材料。一方面,以少层的EG代替石墨可以减少由于钾的嵌入/脱嵌所引起的体积膨胀和内部应力;另一方面,外层rGO可以避免EG的堆叠,这有利于加速动力学过程并在钾化/去钾化过程中稳定结构。当复合材料所用EG和GO的质量比为1 : 1时,其性能达到最优,在50 mA·g^-1的电流密度下能够提供443 mAh·g^-1的比容量;在电流密度为800 mA·g^-1时,比容量为190 mAh·g^-1,保持率为42.9%。相同测试条件下,纯EG和rGO的容量保持率仅为14.2%和27.2%。测试结果说明EG-1/rGO-1复合材料在比容量和倍率性能两个方面得到了提升。     

基于分子印迹聚合物掺杂氧化石墨烯膜的利巴韦林电位传感器

以利巴韦林为模板分子,甲基丙烯酸为功能单体,采用沉淀聚合法制备利巴韦林分子印迹聚合物(MIP).以利巴韦林分子印迹聚合物掺杂氧化石墨烯(GO)为离子载体,聚氯乙烯为基质,癸二酸二辛酯为增塑剂制备电极敏感膜.结果表明,敏感膜组成为100.8 mg MIP、14.7 mg GO、450.8 mg聚氯乙烯和901.6 mg癸二酸二辛酯,内充液组成为0.1 mol/L NaCl+0.05 mol/L NaAc-0.05 mol/L HAc缓冲溶液+ 1.0×10.-5 mol/L利巴韦林,电极的响应性能最好.此电极的能斯特响应斜率为45.565 mV/decade,线性范围为1.0×10.-6~1.0×10.-4 mol/L, 检出限为1.0×10.-7 mol/L(S/N=3),工作pH范围为3~5,响应时间小于3 min.此电极对利巴韦林具有高选择性,可用于检测饲料和注射液中利巴韦林含量,加标回收率为90%~110%,RSD为3.0%~7.9%.     

Graphene Oxide Modified Chemically Activated Graphite Electrodes for Detection of microRNA

In our study, graphene oxide (GO) modified graphite electrodes were used for sensitive and selective impedimetric detection of miRNA. After chemical activation of pencil graphite electrode (PGE) surface using covalent agents (CA), GO modification was performed at the surface of chemically activated PGE. Then, CA‐GO‐PGEs were applied for impedimetric miRNA detection. The microscopic and electrochemical characterization of CA‐GO‐PGEs was performed by scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). The optimization of experimental conditions; such as GO concentration, DNA probe concentration and miRNA target concentration was performed by using EIS technique. After the hybridization occurred between miRNA‐34a RNA target and its complementary DNA probe, the hybrid was immobilized onto the surface of CA‐GO‐PGEs. Then, the impedimetric detection of miRNA‐DNA hybridization was performed by EIS. The selectivity of our assay was also tested under the optimum experimental conditions.     

希瓦氏菌介导制备还原氧化石墨烯薄膜及其增强的胞外电子传递

采用单室、三电极体系,通过希瓦氏菌(Shewanella)还原氧化石墨烯(GO)膜,制备了石墨烯(rGO)薄膜,并通过X射线衍射(XRD)和拉曼光谱(Raman)等手段表征了GO还原前后的结构和性质,证明了Shewanella菌可以有效将GO膜还原为rGO.以该生物还原得到的rGO薄膜为工作电极,可以有效改善Shewanella菌的胞外电子转移(EET).与空白的氧化铟锡(ITO)电极相比,rGO电极的阳极输出电流增大了13%,电量增加90%.该Shewanella还原法是一种温和制备rGO膜的方法,制得的rGO膜改善了微生物的EET效率.     

Green Synthesis of Ag Nanoparticles by Callicarpa Maingayi: Characterization and Its Application with Graphene Oxide for Enzymeless Hydrogen Peroxide Detection

A facile green synthesis of silver nanoparticles (AgNPs) was achieved using aqueous leaf extract of Callicarpa Maingayi as a reducing and stabilizing agent during the synthesis from its salt solutions. The synthesized silver nanoparticles were analyzed with transmission electron microscopy (TEM), X‐ray diffraction (XRD) and energy dispersive spectrometer (EDS). XRD study shows that the particles are crystalline in nature with face centered cubic geometry. The crystallite size obtained from XRD is about 15 nm which is in agreement well with the TEM results. A new nanostructure sensor was constructed by immobilizing silver nanoparticles and graphene oxide (AgNPs‐GO) composite film on a glassy carbon electrode (AgNPs‐GO/GCE). It was found that the AgNPs‐GO composite exhibits good catalytic activity toward the reduction of hydrogen peroxide (H₂O₂), leading to an enzymeless sensor with a fast amperometric response time of less than 5 s, high selectivity, good reproducibility and stability. The linear range was 5.0 μM to 700 μM with a detection limit of 0.6 μM (S/N = 3).     

In situ Synthesis of Poly(methyl methacrylate)/Graphene Oxide Nanocomposites Using Thermal-initiated and Graphene Oxide-initiated Polymerization

A facile and cost-effective method to prepare poly(methyl methacrylate) (PMMA)/graphene oxide (GO) nanocomposites was developed by in situ polymerization. By using thermal-initiated and GO-initiated polymerization of methyl methacrylate (MMA), no extra radical initiator was added during the reaction. Without any pre-functionalization of GO, PMMA chains were covalently bonded to its surface, which was confirmed by Fourier-transform infrared, atomic force microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy investigations. TGA analysis showed that the mass ratio of grafted PMMA and GO was as high as 1.7. Transmission electron microscopy and X-ray powder diffraction investigations demonstrated that the grafting of PMMA chains to GO surfaces resulted in homogeneous dispersion of GO sheets in PMMA matrix, which led to a commendable performance on its mechanical and thermal properties. Dynamic mechanical analysis showed that, at a loading level of just 0.5 wt% for the nanocomposites, the storage modulus of the nanocomposites was improved 14%, and the glass transition temperature was increased 12°C in comparison with that of neat PMMA. Thermogravimetric analysis showed that the onset degradation temperature of the nanocomposites was increased 13°C with a GO content of 0.25 wt%.     

Comparison of Adsorption of Proteins at Di erent Sizes on Pristine Graphene and Graphene Oxide

Using all-atom molecular dynamics (MD) simulations, we have investigated the adsorption stability and conformation change of different proteins on the surface of pristine graphene (PG) and graphene oxide (GO). We find that: (ⅰ) with the cooperation of the electrostatic interactions between proteins and oxygen-containing groups, GO shows better adsorption stability than PG; (ⅱ) the peptide loses its secondary structure on both PG and GO surface, and the α-helix structure of the protein fragment is partially broken on PG surface, but is well preserved on GO surface, while the secondary structure of globular protein has no distinct change on both PG and GO surface. In general, GO presents better biocompatibility than PG. Our results are of significant importance to understand the interactions between proteins and PG/GO and the applications of PG/GO in biotechnology and biomedicine.     

功能化氧化石墨烯的细胞相容性

采用改进的Hummers方法制备了纳米尺度的氧化石墨烯.对氧化石墨烯的表面进行羧基化,并连接上聚乙二醇(PEG)使其在细胞培养液中可溶并能稳定保存.采用透射电镜(TEM)、傅里叶变换红外(FTIR)光谱和zeta电位测量等对修饰后的氧化石墨烯的结构和功能进行了表征.体外细胞实验表明PEG修饰的氧化石墨烯在水中具有良好的可溶性,对A549细胞没有明显的毒性,在生物医药领域具有潜在的应用价值.     

羧基化氧化石墨烯的血液相容性

氧化石墨烯的官能团修饰可促进氧化石墨烯与生物体液、聚合物基体等不同环境的融合. 通过超声法制备了氧化石墨烯, 并利用化学改性的方法, 将氧化石墨烯表面的羟基和环氧基转变为羧基. 红外图谱上羧基化氧化石墨烯(GeneO-COOH)的羧基振动明显, 峰强增大. GeneO-COOH的主要失重表现为羧基官能团缩合以一个水分子的形态释放失去结构水[OH2]. 复钙动力学曲线随着GeneO-COOH的浓度增加, 曲线上升趋势由陡峭趋于平缓, 当浓度为1.25 μg/mL时复钙时间延长了11 min, 平台期OD值降低了8.14 %; 在0.5~100 μg/mL浓度范围内溶血率均<5 %. GeneO-COOH比GeneO在同等低浓度下的抗凝血性能有一定程度的改善, 主要是因为带负电的羧基可直接络合凝血因子. 因此, 羧基修饰氧化石墨烯是提高血液相容性的有效手段, 羧基化氧化石墨烯可作为潜在的生物医用材料的填料.