表面接枝含氟苯乙烯共聚物的聚酯薄膜制备与表征

利用表面引发原子转移自由基聚合(SI-ATRP)在聚对苯二甲酸乙二醇酯(PET)薄膜表面接枝苯乙烯和4-氟苯乙烯的共聚物.研究不同反应时间和不同配比下接枝共聚物对聚酯薄膜表面组成、结构和性能的影响.通过傅利叶变换红外光谱仪(ATR/FTIR),X-射线光电子能谱仪(XPS),凝胶渗透色谱(GPC)和扫描电子显微镜(SEM)对接枝改性前后PET薄膜的表面组成,结构和形貌进行分析;利用接触角测试和表面能计算对比研究接枝改性前后PET薄膜的表面性能.结果表明反应时间和单体百分含量对接枝百分率及接触角有一定的影响,随着反应时间的增长,聚酯薄膜表面接枝百分率增大,接触角增加,表面自由能下降.     

表面温度敏感性聚酯薄膜的制备

通过在聚酯(PET)薄膜表面固定原子转移自由基聚合(ATRP)的引发基团,继而引发接枝聚N-异丙基丙烯酰胺(NIPAM),制备表面具有温度敏感性的聚酯薄膜.利用X射线光电子能谱仪(XPS),衰减全反射傅立叶变换红外光谱仪(FTIR/ATR),扫描电子显微镜(SEM)对接枝改性前后PET薄膜的表面组成,结构和形貌进行分析与表征;利用接触角测试仪对比研究接枝改性前后PET薄膜的表面性能;研究数据表明,随着反应时间的延长,接枝到PET薄膜表面PNIPAM的量在增加.当接枝聚合反应时间为16 h,接枝量达到0.239mg/cm2.表明SI-ATRP具有一定的"活性"特征;接枝PNIPAM改性后的PET薄膜表现出对温度的刺激响应性.     

金表面聚合物刷及图案化微结构的制备

采用表面引发室温原子转移自由基聚合(ATRP)方法在金基底上原位制备了接枝聚合物刷,其制备过程用厚度测量,ATR-FTIR,XPS等进行了表征,初始时聚合物刷的厚度随着聚合时间的增加线性增加,表现为活性聚合的特征．XPS表征证明表面引发聚合后聚合物刷末端仍然存在ATRP反应的引发剂．紫外光刻图案化的聚合物刷作为电沉积的模板,经电沉积、后紫外处理、湿化学刻蚀步骤后得到了分离的导电聚合物微阵列结构,通过浇注／粘附处理将导电聚合物微阵列转移至硅油弹性体片,由于导电聚合物在湿化学刻蚀中对基底金具有良好的保护作用,因此在导电聚合物阵列被转移后,基底表面得到金微阵列。     

窄分布聚丙烯酸-g-聚甲基丙烯酸酯接枝共聚物的合成

利用合成的一种新型原子转移自由基聚合大分子引发剂和从主干接枝的方法制备了窄分布的两亲性接枝共聚物聚丙烯酸-g-聚甲基丙烯酸酯, 并对其结构进行表征. 产物主链和侧链的分子量可分别通过调整单体与引发剂的投料比和反应时间进行控制, 结构规整, 侧链单体适用范围广. 该合成方法不仅推动了接枝共聚物合成研究的进展, 其产物更为两亲性接枝共聚物自组装行为的研究提供了很好的研究对象.     

对-氯甲基苯乙烯共聚物引发合成接枝共聚物

接枝共聚物含有性质差别很大的主链和支链,具有许多特殊的性质,因而一直是人们感兴趣的研究课题之一^[1～5].原子转移自由基聚合(ATRP)^[6,7]的问世,为接枝共聚物的合成提供了一条新的途径.本文用对-氯甲基苯乙烯和其它乙烯基单体自由基共聚.     

原子转移自由基聚合(ATRP)在二氧化硅表面接枝中的应用

ATRP方法是在二氧化硅(SiO2)表面接枝聚合物的一种有效方法.通过硅烷偶联剂把ATRP引发剂键接到SiO2表面,然后进行表面ATRP聚合,可以在SiO2表面接枝各种均聚物、嵌段共聚物、超支化聚合物.聚合可以在有机溶剂或水中进行.把ATRP方法同其它聚合方法如氮氧稳定自由基聚合或开环聚合相结合,可以在SiO2表面接枝复杂结构的聚合物如V型嵌段共聚物、梳型共聚物等.SiO2表面ATRP聚合可以通过外加引发剂或外加二价铜来实现聚合可控.     

ATRP法合成接枝共聚物PVDF-g-PNIPAAm及其分离膜的研究

以氯化亚铜(CuCl)/三(N,N-二甲基氨基乙基)胺(Me₆TREN)为催化配位体系, 用DMF作为溶剂, 通过原子转移自由基聚合(ATRP)方法直接在商用聚偏氟乙烯(PVDF)粉末上接枝温敏性材料N-异丙基丙烯酰胺(NIPAAm). 红外光谱(FTIR)和核磁共振(¹H NMR)分析表明, PNIPAAm成功接枝到了PVDF上. 考察了聚合反应时间及反应温度对接枝率的影响. 接枝共聚物以相转化法进行制膜, 通过纯水通量测试温敏性能, 结果表明, PVDF能成功用于ATRP反应, 当温度变化时所制备的PVDF-g-PNIPAAm共聚膜呈现出一定的温度敏感性能.     

两亲性纤维素接枝聚脱氢枞酸共聚物的制备及性能研究

通过均相原子转移自由基聚合法(ATRP)将生物质基疏水性松香单体(脱氢枞酸(2-甲基丙烯酰氧基乙基)酯,MAEDA)接枝到纤维素骨架上合成了全生物质基两亲性的纤维素-g-聚脱氢枞酸接枝共聚物(cellulose-g-PMAEDA).ATRP反应过程动力学研究表明cellulose-g-PMAEDA接枝共聚物的合成过程是活性可控的;傅里叶红外光谱(FTIR)、核磁共振氢谱(1H-NMR)、凝胶色谱(GPC)和X射线衍射(XRD)结果证实了cellulose-g-PMAEDA接枝共聚物的成功合成;由于聚脱氢枞酸侧链的引入,cellulose-g-PMAEDA接枝共聚物的热稳定性,疏水性能明显提高,并且具有紫外吸收性能;动态光散射仪和透射电镜结果表明两亲性cellulose-g-PMAEDA接枝共聚物能够在水溶液中自组装成平均粒径约为200 nm左右的纳米微球,并且该纳米微球具有以纤维素为壳,聚脱氢枞酸酯为核的核壳结构.     

低聚表面活性剂的合成及性能研究

低聚表面活性剂是指通过连接基将两个以上的传统表面活性剂连接在一起而形成的一类新型表面活性剂。相对于对应的传统表面活性剂,这类表面活性剂具有临界胶束浓度(cmc)低、表面活性高等优点。本文介绍了本研究团队近年针对低聚表面活性剂所开展的研究,包括分子结构不对称的双子表面活性剂、同时具有阳离子和阴离子头基的甜菜碱型双子表面活性剂、三聚和四聚阳离子表面活性剂以及通过原子转移自由基聚合制备的低聚表面活性剂等。     

One‐Reactant Photografting of ATRP Initiators for Surface‐Initiated Polymerization

Self‐initiated photografting polymerization is used to couple the polymerizable initiator monomer 2‐(2‐chloropropanoyloxy)ethyl acrylate to a range of polymeric substrates. The technique requires only UV light to couple the initiator to surfaces. The initiator surface density can be varied by inclusion of a diluent monomer or via selection of initiator and irradiation parameters. The functionality of the initiator surface is demonstrated by subsequent surface‐initiated atom transfer radical polymerization. Surfaces are characterized by x‐ray photoelectron spectroscopy (XPS), ellipsometry, and atomic force microscopy (AFM), and UV‐induced changes to the initiator are assessed by ¹H NMR and gel permeation chromatography (GPC). This is the first time this one‐reactant one‐step technique has been demonstrated for creating an initiator surface of variable density.

     

Synthesis of Chlorogenic Acid Imprinted Chromatographic Packing by Surface-initiated Atom Transfer Radical Polymerization and Its Application

A novel chromatographic packing of chlorogenic acid（CGA） molecularly imprinted polymer（MIP） based on the 5.0 ~tm silica was prepared by surface initiated atom transfer radical polymerization（SI-ATRP） with 4-vinylpyridine（4-VP） as functional monomer, ethyl glycol dimethacrylate（EDMA） as cross-linker in the mixture of methanol and water（7：3, volume ratio） under mild reaction conditions. The characteristics of CGA MIP were investi- gated by elemental analysis, thermogravimetric analysis（TGA）, Fourier transform infrared spectrometry（FTIR） and atomic force microscopy（AFM）. The effects of some chromatographic conditions such as mobile phase composition and temperature on the retention time were investigated. The adsorption capacity of the stationary phase for com- pounds was determined by frontal chromatographic technique. The results show that Freundlich isotherm fits the ex- perimental adsorption isotherm data better than Langmuir model does. The relatively high heterogeneity index values regressed with the Freundlich isotherm suggest the formation of fairly homogeneous MIP. Thermodynamic data（AAH and AAS） obtained by van＇t Hoff plots reveal an entropy-controlled separation. The CGA MIP column was shown to be successful for the separation and purification of chlorogenic acid from the extract of Honeysuckle.     

A novel hydrophilic polystyrene-based beads for hydrophilic interaction chromatography by surface-initiated atom transfer radical polymerization

A one-step procedure to hydrophilize monodisperse poly(chloromethyl-styrene-co-divinylbenzene) beads has been presented with 2-hydroxy-3-[4-(hydroxymethyl)-1H-1,2,3-triazol-1-yl]propy1 2-methylacrylate(HTMA) as monomer by surface-initiated atom transfer radical polymerization(SI-ATRP).The length of the grafted poly(HTMA) chain was varied via controlling the ratio of HTMA to initiator on the surface of the beads.Using these grafted beads as the stationary phase in hydrophilic interaction chromatography,good separation was obtained for nucleosides in the mobile phase of acetonitrile-water.It was also found that the retention time and selectivity of solutes showed a positive relationship with the length of the grafted poly(HTMA) chain.     

表面自由基链转移反应制备超萍聚合物膜

研究了通过自由基链转移反应原位接枝聚合物膜。所得聚合物膜经红外（FT- IR）、X射线光电子能谱（XPS）、原子力显微镜（AFM）、接触角及椭圆偏光测量 进行了表征。两种单体如苯乙烯/甲基丙烯酸甲酯共聚合时,改变单体对的组成, 可以得到不同亲水亲油性质的表面。     

原子转移自由基聚合制备聚酯二元醇接枝聚苯乙烯

聚酯二元醇经氯甲基化制备了聚酯二元醇大分子引发剂,通过原子转移自由基聚合技术,合成了聚酯二元醇－ｇ－聚苯乙烯接枝聚合物。用＾１Ｈ－ＮＭＲ、ＦＴ－ＩＲ和ＧＰＣ表征了接枝聚合物,结果表明分子量与转化率呈线性关系,且分子量分布较窄,接枝聚合反应是一个可控过程。     

三嵌段共聚物PAN-b-PEG-b-PAN的合成及其自组装行为的研究

利用原子转移自由基聚合(ATRP)制得了分子量可控、分子量分布窄的聚丙烯腈-b-聚乙二醇-b-聚丙烯腈P(AN-b-PEG-b-PAN)嵌段共聚物. 通过¹H NMR, FTIR, 凝胶渗透色谱(GPC)对所得产物的结构和分子量进行了表征并通过TG和DTA考察了该嵌段共聚物的热稳定性; 运用透射电子显微镜(TEM)、荧光探针技术和动态光散射(DLS)研究了P(AN)₂₇-b-P(EG)₄₅-b-P(AN)₂₇在溶剂水中胶束的形成、结构、形貌和胶束粒径. 结果表明, 三嵌段共聚物P(AN)₂₇-b-P(EG)₄₅-b-P(AN)₂₇的热稳定性较纯聚乙二醇P(EG)好, 且柔性链PEG的引入对嵌段共聚物的放热峰位置没有显著的影响. 当改变此嵌段共聚物溶液浓度时, 该嵌段共聚物会自组装成不同形状的胶束, DLS测量的胶束粒径大于TEM观察的结果, 其临界胶束浓度(cmc)约为4.46×10^－4 g•L^－1.     

Preparation of End Grafted Polyacrylonitrile Brushes through Surface Confined Radical Chain Transfer Reaction

End grafted polyacrylonitrile (PAN) brush was prepared through surface initiated polymerization via the chain transfer process.The thiol-terminated monolayer and PAN brushes were characterized by FTIR,X-ray photoelectron spectroscopy(XPS),atomic force microscopy (AFM),ellipsometry and contact angle measurements etc.It is demonstrated that radical chain transfer reaction and surface initiated precipitate polymerization can used to prepare end-grafted polymer brushes.     

PS-b-PAA嵌段共聚物修饰的智能表面的制备及其响应行为的研究

利用原子转移自由基聚合(ATRP), 再经水解后得到了嵌段共聚物聚苯乙烯-b-聚丙烯酸(PS-b-PAA), 接枝到硅烷偶联剂γ-(2,3环氧丙氧)丙基三甲氧基硅烷[γ-(2,3-glycidoxypropyl)trimethoxysilane, GPS]修饰的Si表面得到了对溶剂具有响应性的智能表面, 并通过凝胶渗透色谱(GPC)、傅立叶变换红外光谱(FTIR)、核磁共振(¹H NMR)和原子力显微镜(AFM)等测试手段对产物进行了表征. 然后, 通过接触角测试研究了所得智能表面对不同溶剂的响应行为. 结果显示, PS-b-PAA接枝表面的润湿性与接枝共聚物的组成及表面处理的溶剂性质有关. 在相同的溶剂处理条件下, 共聚物中PS/PAA比值越小, 表面亲水性越大; 乙醇和碱性溶液处理后的表面呈亲水状态, 甲苯和酸性水溶液处理后的表面又切换到疏水状态, 同时其表面的酸碱响应行为具有非常稳定的可逆性.     

Growth of poly(methyl methacrylate) brushes on silicon surfaces by atom transfer radical polymerization

Poly(methyl methacrylate) (PMMA) brushes are grown by surface‐initiated atom transfer radical polymerization on silicon surfaces at various polymerization temperatures. Kinetic studies show that the layer thickness scales linearly with the degree of polymerization of the polymers under some conditions, indicating a constant graft density of the surface‐attached chains. At high temperatures, the layer growth is a controlled process only for short reaction times, and after a rapid increase, the film growth levels off, and a constant thickness is obtained. At lower reaction temperatures, polymers with a lower polydispersity are obtained, but at the expense of a much slower growth rate. Accordingly, intermediate temperatures yield the highest film thickness on experimentally feasible timescales. The reinitiation of these surface‐grafted PMMA chains at room temperature to either extend the chains or grow a chemically different polyglycidylmethacrylate block demonstrates the presence of active ends and the living nature of the surface‐grafted PMMA chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1758–1769, 2006