Synthesis of functional graft copolymers by solution copolymerization and their evaluation as dispersants in nonaqueous phase dispersion polymerization

The poly(HEMA‐co‐MMA‐g‐PMMA) graft copolymer was prepared with a poly(methyl methacrylate) (PMMA) macromonomer, 2‐hydroxyethyl methacrylate (HEMA), and methyl methacrylate (MMA), and its application as a dispersant for the nonaqueous phase dispersion polymerization of polystyrene (PST) was investigated. Monodisperse PST particles were obtained with two‐dimensionally tailored graft copolymers, with the number of grafted chains controlled and the polar component (HEMA) in the backbone chains balanced. As for the reactor, a stirred vessel with moderate agitation yielded uniform polymer particles, whereas sealed glass ampules with an overturning motion yielded broader size distributions. Increasing the polarity of the solvent in the continuous phase yielded smaller polymer particles with a gradual deterioration of monodispersity. Uniform polymer particles with a coefficient of variation of less than 6% were obtained up to 30 wt % solid contents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1788–1798, 2003     

Reverse Atom Transfer Radical Polymerization of MMA in the Presence of CaCO3/SiO2 Two-Component Composite Particles

Summary: We previously discovered that structurally well-defined polymer/inorganic composite particles, i.e., poly(methyl methacrylate) (PMMA)/CaCO₃/SiO₂ three-component composite particles, can be achieved via reverse atom transfer radical polymerization (ATRP), using 2,2′-azo-bis-isobutyronitrile as initiator and Cu^II bromide as catalyst. In the present study, the influence of the mass ratio of CaCO₃/SiO₂ two-component composite particles to methyl methacrylate (MMA) on the rate and behavior of the polymerization was studied in detail. The results illustrate that increasing the mass ratio of CaCO₃/SiO₂ two-component composite particles will decrease the overall rate of polymerization of MMA under standard reverse ATRP conditions. Thermal properties of the obtained well-defined particles were characterized and determined by thermogravimetric analysis (TGA). The results indicate that well-defined PMMA chains grafted on the surface of CaCO₃/SiO₂ particles were only degraded by random chain scission of C C linkages within the PMMA chain, which is different from the degradation of PMMA chains prepared via traditional radical polymerization. This difference is reasonably ascribed to the difference between the end groups of PMMA prepared via reverse ATRP and that via traditional radical polymerization, which has been confirmed by end group analysis measured by ¹H–NMR spectroscopy.     

Fluorine‐containing linear block terpolymers: Synthesis and self‐assembly in solution

Linear triblock terpolymers of poly(n‐butyl methacrylate)‐b‐poly(methyl methacrylate)‐b‐poly(2‐fluoroethyl methacrylate) (PnBMA‐PMMA‐P2FEMA) were synthesized by sequential reversible addition fragmentation chain transfer (RAFT) polymerization. Kinetic studies of the homopolymerization of 2FEMA by RAFT polymerization demonstrated controllable characteristics with fairly narrow polydispersities (～1.30). The resultant PnBMA‐PMMA‐P2FEMA triblock terpolymers were characterized via ¹H NMR, ¹⁹F NMR, and gel permeation chromatography. These polymers formed micellar aggregates in a selective solvent mixture. The as‐formed micelles were analyzed using scanning electron microscopy and dynamic light scattering. It was found that these terpolymers could directly self‐organize into complex micelles in a tetrahydrofuran/methanol mixture with diameters that depended on polymer composition. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Dispersion polymerization of methyl methacrylate: Mechanism of particle formation

The mechanism for the formation of micron-size polymer particles in the dispersion polymerization of methyl methacrylate was investigated by applying dynamic light scattering to monitor the evolution of the average particle size in the early stages of the polymerization. In addition, the contributions of physically adsorbed stabilizer and graft copolymer were evaluated by measuring the bound, unbound (adsorbed), and free stabilizer, and by determining the amount of added stabilizer required in seeded dispersion polymerizations. Twenty nanometer particles (termed nuclei) were the smallest particles detected and are considered to be formed by aggregation of growing polymer chains precipitating from solution as they exceed their critical chain length. Aggregation of these nuclei with themselves and their aggregates continues until mature and stable particles are formed. This occurs when sufficient stabilizer occupies the particle surface which includes both the polymeric stabilizer [poly(vinylpyrrolidone)] and its graft copolymer which is created in situ. The effects of process variables are discussed based on this mechanistic picture of the dispersion polymerization process. © 1994 John Wiley & Sons, Inc.     

Structure of reactively extruded rigid PVC/PMMA blends

A novel route for producing polymer blends by reactive extrusion is described, starting from poly (vinyl chloride)/methyl methacrylate (PVC/MMA) dry blend and successive polymerization of MMA in an extruder. Small angle X‐ray scattering (SAXS) measurements were applied to study the monomer's mode of penetration into the PVC particles and to characterize the supermolecular structure of the reactive poly(vinyl chloride)/poly(methyl methacrylate) (PVC/PMMA) blends obtained, as compared to the corresponding physical blends of similar composition. These measurements indicate that the monomer molecules can easily penetrate into the PVC sub‐primary particles, separating the PVC chains. Moreover, the increased mobility of the PVC chains enables formation of an ordered lamellar structure, with an average d‐spacing of 4.1 nm. The same characteristic lamellar structure is further detected upon compression molding or extrusion of PVC and PVC/PMMA blends. In this case the mobility of the PVC chains is enabled through thermal energy. Dynamic mechanical thermal analysis (DMTA) and SAXS measurements of reactive and physical PVC/PMMA blends indicate that miscibility occurs between the PVC and PMMA chains. The studied reactive PVC/PMMA blends are found to be miscible, while the physical PVC/PMMA blends are only partially miscible. It can be suggested that the miscible PMMA chains weaken dipole–dipole interactions between the PVC chains, leading to high mobility and resulting in an increased PVC crystallinity degree and decreased PVC glass transition temperature (T_g). These phenomena are shown in the physical PVC/PMMA blends and further emphasized in the reactive PVC/PMMA blends. Copyright © 2005 John Wiley & Sons, Ltd.     

One‐Pot Fabrication of Supramolecular Polymer Particles via Situ Polymerization Stringed Assembly of a Two‐Monomer Microemulsion

Summary: A novel method, situ polymerization stringed assembly (SPSA), is proposed to prepare stable solid or hollow supramolecular polymer particles, which are assembled by numerous nanoparticles. By this method, the fabrication of primary nanoparticles (poly(methyl methacrylate), PMMA), the linkers (polyvinylpyrrolidone, PVP, chains) between the nanoparticles, and the final assembled solid or hollow particles could be achieved in just one‐pot by methyl methacrylate (MMA)/N‐vinylpyrrolidone (NVP) microemulsion polymerization under UV irradiation. The structures of the supramolecular particles can be changed from solid to hollow by tuning the mass ratio of MMA/NVP in the microemulsion. AFM, TEM, and SEM experiments are performed to identify the results.

AFM image of the PMMA/PVP solid particles obtained from the photopolymerization of the microemulsion containing 20 wt.‐% MMA, 10 wt.‐% NVP, and 5 × 10⁻² wt.‐% BP.     

Synthetic and characterization aspects of dimethylaminoethyl methacrylate reversible addition fragmentation chain transfer (RAFT) polymerization

2‐cyanoprop‐2‐yl dithiobenzoate (CPDB) mediated RAFT polymerization of dimethylaminoethyl methacrylate (DMAEMA) was carried out in dioxane at 90 °C. The influence of several parameters, such as the monomer to CPDB molar ratio (100 to 500), the monomer concentration (2 mol·L^?1 to 5.9 mol·L^?1), and CPDB to initiator molar ratio (1 to 10), was evaluated with regards to conversion and polymerization duration, as well as control of molar mass and molar mass distributions. Number average molar masses from 10,000 to 70,000 g·mol^?1 can be targeted. The determination of the molar masses has been carried out by size exclusion chromatography (SEC) with a refractometer detector with poly(methyl methacrylate) (PMMA) standards. The experimental values were lower than the expected ones. Then, SEC in aqueous medium with an online laser light scattering detector was used both to get absolute molar masses and to recalibrate the SEC column in THF. Characterization of well‐controlled PDMAEMA samples has been performed by proton NMR spectroscopy and matrix assisted laser desorption ionization time of flight mass spectrometry. Finally, a chain extension experiment was evaluated with regard to living features. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3551–3565, 2005     

PMMA colloid particles armored by clay layers with PDMAEMA polymer brushes

Poly[2‐(dimethylamino) ethyl methacrylate] (PDMAEMA) brushes on the surfaces of clay layers were prepared by in situ free‐radical polymerization. Poly (methyl methacrylate) (PMMA) colloid particles stabilized and initiated by clay layers with PDMAEMA polymer brushes were prepared by Pickering emulsion polymerization. Transmission electron microscopy was used to characterize the structure and morphology of the colloid particles. The X‐ray diffraction (XRD) results indicated that the intercalated structures of the clay layers were almost destroyed in Pickering emulsion polymerization, and clay layers with exfoliated structures were created. The surface of the colloid particles was analyzed by using X‐ray photoelectron spectroscopy (XPS). The XPS results provide direct evidence that the clay layers with PDMAEMA chains cover the PMMA colloid particles. © 2008 Wiley Periodicals, Inc. JPolym Sci Part A: Polym Chem 46: 2632–2639, 2008     

Grafting of Polymer Brushes from Xanthate-Functionalized Silica Particles

Monodisperse silica particles (SiPs) were surface-modified with a newly designed silane coupling agent comprising a triethoxysilane and an alkyl halide, namely, 6-(triethoxysilyl)hexyl 2-bromopropionate, which was further treated with potassium O-ethyl dithiocarbonate (PEX) to immobilize xanthate molecules on the particle surfaces. Surface-initiated macromolecular design via interchange of xanthates (MADIX) polymerization of vinyl acetate (VAc) was conducted with the xanthate-functionalized SiPs. The polymerization was well controlled and produced SiPs coated with poly(vinyl acetate) (PVAc) with a well-defined target molar mass and a graft density of about 0.2 chains nm⁻². Dynamic light scattering and TEM measurements revealed that the hybrid particles were highly dispersible in good solvents without any aggregation. The PVAc brushes were hydrolyzed with hydrochloric acid to produce poly(vinyl alcohol) brushes on the SiP surfaces. In addition, the number of xanthate molecules introduced on the SiP surfaces could be successfully controlled by adjusting the concentration of PEX. Thus, the SiPs have two functionalities: xanthates able to act as a MADIX chain-transfer agent and alkyl bromide initiation sites for atom transfer radical polymerization (ATRP). By using these unique bifunctional particles, mixed polymer brushes were constructed on the SiPs by MADIX of VAc followed by ATRP of styrene or methyl methacrylate.     

Dispersion polymerization of MMA in supercritical CO2 stabilized by random copolymers of 1H,1H–perfluorooctyl methacrylate and 2‐(dimethylaminoethyl methacrylate)

A series of random copolymers, composed of 1H,1H‐perfluorooctyl methacrylate (FOMA) and 2‐dimethylaminoethyl methacrylate (DMAEMA) were prepared as stabilizers for the dispersion polymerization of methyl methacrylate in supercritical CO₂ (scCO₂). Free‐flowing, spherical poly(methyl methacrylate) (PMMA) particles were produced in high yield by the effective stabilization of poly(FOMA‐co‐DMAEMA) containing 34–67 w/w % (15–41 m/m %) FOMA structural units. Less stabilized but micron‐sized discrete particles could be obtained even with 25 w/w % (10 m/m %) FOMA stabilizer. The result showed that the composition of copolymeric stabilizers had a dramatic effect on the size and morphology of PMMA. The particle size was controllable with the surfactant concentration. The effect of the monomer concentration and the initial pressure on the polymerization was also investigated. The dry polymer powder obtained from dispersion polymerization could be redispersed to form stable aqueous latexes in an acidic buffered solution (pH = 2.1) by an electrostatic stabilization mechanism due to the ionization of DMAEMA units in the stabilizer. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1365–1375, 2008     

Nano cellulose particles covered with block copolymer of cellulose and methyl methacrylate produced by solid mechano chemical polymerization

Nano cellulose particles covered with a block copolymer of microcrystalline cellulose and poly(methyl methacrylate) (MCC-block-PMMA) were produced by a solid mechano-chemical polymerization. The polymerization of methyl methacrylate was initiated by chain-end-type microcrystalline cellulose (MCC) radicals (i.e., MCC mechano radicals) on the surface of MCC that were induced by mechanical fracture of β-1,4 glycosidic linkages. The chemically modified cellulose particles with MCC-block-PMMA were fractionated by Soxhlet extraction with chloroform, and resulted in MCC-block-PMMA residue from residue on the filter and MCC-block-PMMA filtrate from filtrate solution. The surface of the MCC particles chemically modified with MCC-block-PMMA in MCC-block-PMMA residue was partially covered with PMMA chains of the MCC-block-PMMA. In contrast, the surfaces of the MCC nanoparticles chemically modified with MCC-block-PMMA in MCC-block-PMMA filtrate were fully covered with PMMA chains of the MCC-block-PMMA. A dispersion of the chemically fully modified MCC nanoparticles in chloroform was optically transparent. The average diameter of the chemically fully modified MCC nanoparticles in chloroform was estimated to be 52 nm. These were confirmed by electron spin resonance, Fourier transform infrared, and ¹H nuclear magnetic resonance spectroscopy, by gel permeation chromatography and dynamic light scattering.     

Star‐shaped polymers by Ru(II)‐catalyzed living radical polymerization. II. Effective reaction conditions and characterization by multi‐angle laser light scattering/size exclusion chromatography and small‐angle X‐ray scattering

Star poly(methyl methacrylate)s (P*) of various arm lengths and core sizes were synthesized in high yields by the polymer linking reaction in Ru(II)‐catalyzed living radical polymerization. The yields of the star polymers were strongly dependent on the reaction conditions and increased under the following conditions: (1) at a higher overall concentration of arm chains ([P*]), (2) with a larger degree of polymerization (DP) of the arm chains (arm length), and (3) with a larger ratio (r) of linking agents to P* (core size). In particular, the yields sharply increased in a short time at a higher temperature, in a polar solution, and at a higher complex concentration after the addition of linking agents. These star polymers were then analyzed by multi‐angle laser light scattering to determine the weight‐average molecular weight (3.8 × 10³ to 1.5 × 10⁶), the number of arm chains per molecule (f = 4–63), and the radius of gyration (R_z = 2–22 nm), which also depended on the reaction conditions (e.g., f and R_z increased as [P*], DP, and r increased). Small‐angle X‐ray scattering analyses of the star polymers showed that they consisted of spheres for which the radius of the microgel core was 2.7 nm. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2245–2255, 2002     

Functionalization of iron oxide magnetic nanoparticles with poly(methyl methacrylate) brushes via grafting‐from atom transfer radical polymerization

A key problem with nanomaterials is the difficulty of controlling the dispersion of nanoparticles inside an organic medium. To overcome this problem, functionalization of the nanoparticle surface is required. Poly(methyl methacrylate) (PMMA) brushes were grown on the surface of iron oxide magnetic nanoparticles with atom transfer radical polymerization and a grafting‐from approach. Modified magnetic nanoparticles with a graft density of 0.1 PMMA chains/nm² were obtained. Cu(II), used as a deactivating complex, allowed good control of the polymerization along with a narrow polydispersity of the polymer chains. The functionalized magnetic nanoparticles were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, gel permeation chromatography, and atomic force microscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 925–932, 2007     

Effect of graft polymer on the formation of micron-sized,monodisperse, "onion-like" alternately multilayered poly(methyl methacrylate)/polystyrene composite particles by reconstruction of morphology with the solvent-absorbing/releasing method

Some factors contributing to the formation of an alternately multilayered structure of micron-sized, monodisperse poly(methyl methacrylate) (PMMA)/polystyrene (PS) (1/1, w/w) composite particles by reconstruction of the morphology with the solvent-absorbing/releasing method (SARM) were discussed. The original composite particles, which were produced by seeded dispersion polymerization (SDP) of styrene, had a core–shell structure. When PS/PMMA (1/1, w/w) composite particles produced by SDP of methyl methacrylate were treated by the SARM with toluene, the reconstructed morphology of the composite particles was not the multilayered structure but a hemisphere (or core–shell). The PS/PMMA composite particle contained less than 10 wt% PMMA- g-PS. On the other hand, the PMMA/PS composite particles contained about 40 wt% graft polymer. The graft polymer would exist at the interfaces of the alternate multilayers and decrease their interfacial energy. This was the main reason why the alternately multilayered structure was constructed by the SARM, though the total interfacial area between PMMA and PS layers in the multilayered particle is much larger than that of the hemisphere (or core–shell).     

Anomalous solubility of polyacrylamide prepared by dispersion (precipitation) polymerization in aqueous tert‐butyl alcohol

Polyacrylamide prepared by dispersion (precipitation) polymerization in an aqueous t‐butyl alcohol (TBA) medium is only partially soluble when the TBA concentrations in the polymerization media are in the range 82 vol % < TBA < 95 vol %. Independent experiments with a soluble (linear) sample of polyacrylamide show that the polymer swells sufficiently in the aforementioned media to lower the glass‐transition temperature of the polymer below the polymerization temperature (50 °C). The anomalous solubility has been attributed to the crosslinking of polymer chains that occurs during the solid‐phase polymerization of acrylamide in the swollen polymer particles. It is postulated that some of the radical centers shift from the chain end to the chain backbone during solid‐phase polymerization by chain transfer to neighboring polymer molecules, and when pairs of such radicals come into close vicinity, crosslinking occurs. However, dispersion (precipitation) polymerization in other media such as aqueous methanol and aqueous acetone yields polymers that are soluble. This result has been attributed to the fact that the polymer radical undergoes a chain‐transfer reaction with these solvents at a much faster rate than with TBA, which overcomes the effect of the polymer‐transfer reaction. Even the addition of as little as 5% methanol to a TBA–water mixture (TBA:water = 85:10) gives rise to a soluble polymer. The chain‐transfer constants for acetone, methanol, and TBA have been determined to be 9.0 × 10^?6, 6.9 × 10^?6, and 1.48 × 10^?6, respectively, at 50 °C. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3434–3442, 2001     

PS/PMMA mixed polymer brushes on the surface of clay layers: Preparation and application in polymer blends

Polystyrene (PS) and poly(methyl methacrylate) (PMMA) mixed polymer brushes on the surface of clay layers were prepared by using in situ free radical polymerization. Free radical initiator molecules with two quaternary ammonium groups at both ends were intercalated into the interlayer spacing of clay layers. The amount of polymer brushes grafted on the surface of clay layers can be controlled by controlling the polymerization time. Thermogravimetric analysis, X‐ray diffraction, and high‐resolution transmission electron microscope results indicated successful preparation of the mixed polymer brushes on the surface of clay layers. The kinetics of the grafting of the monomers was also studied. The mixed polymer brushes on the surface of clay layers were used as compatibilizers in blends of PS and PMMA. In the blends, the intercalated clay particles tend to locate at the interface of two phases reducing the interfacial tension. In the meanwhile, PMMA homopolymer chains tend to intercalate into clay layers. The driving force for the intercalation is the compatibility between homo‐PMMA chains and PMMA brushes on the surface of clay layers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5329–5338, 2007     

In situ Synthesis of Poly(methyl methacrylate)/Graphene Oxide Nanocomposites Using Thermal-initiated and Graphene Oxide-initiated Polymerization

A facile and cost-effective method to prepare poly(methyl methacrylate) (PMMA)/graphene oxide (GO) nanocomposites was developed by in situ polymerization. By using thermal-initiated and GO-initiated polymerization of methyl methacrylate (MMA), no extra radical initiator was added during the reaction. Without any pre-functionalization of GO, PMMA chains were covalently bonded to its surface, which was confirmed by Fourier-transform infrared, atomic force microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy investigations. TGA analysis showed that the mass ratio of grafted PMMA and GO was as high as 1.7. Transmission electron microscopy and X-ray powder diffraction investigations demonstrated that the grafting of PMMA chains to GO surfaces resulted in homogeneous dispersion of GO sheets in PMMA matrix, which led to a commendable performance on its mechanical and thermal properties. Dynamic mechanical analysis showed that, at a loading level of just 0.5 wt% for the nanocomposites, the storage modulus of the nanocomposites was improved 14%, and the glass transition temperature was increased 12°C in comparison with that of neat PMMA. Thermogravimetric analysis showed that the onset degradation temperature of the nanocomposites was increased 13°C with a GO content of 0.25 wt%.     

Synthesis of amphiphilic poly(methyl methacrylate‐ b‐ethylene oxide) copolymers from monohydroxy telechelic poly(methyl methacrylate) as macroinitiator

The synthesis of well‐defined poly(methyl methacrylate)‐block‐poly(ethylene oxide) (PMMA‐b‐PEO) dibock copolymer through anionic polymerization using monohydroxy telechelic PMMA as macroinitiator is described. Living anionic polymerization of methyl methacrylate was performed using initiators derived from the adduct of diphenylethylene and a suitable alkyllithium, either of which contains a hydroxyl group protected with tert‐butyldimethylsilyl moiety in tetrahydrofuran (THF) at ?78 °C in the presence of LiClO₄. The synthesized telechelic PMMAs had good control of molecular weight with narrow molecular weight distribution (MWD). The ¹H NMR and MALDI‐TOF MS analysis confirmed quantitative functionalization of chain‐ends. Block copolymerization of ethylene oxide was carried out using the terminal hydroxyl group of PMMA as initiator in the presence of potassium counter ion in THF at 35 °C. The PMMA‐b‐PEO diblock copolymers had moderate control of molecular weight with narrow MWD. The ¹H NMR results confirm the absence of trans‐esterification reaction of propagating PEO anions onto the ester pendants of PMMA. The micellation behavior of PMMA‐b‐PEO diblock copolymer was examined in water using ¹H NMR and dynamic light scattering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2132–2144, 2008     

Radical polymerization of methyl methacrylate in the presence of stereoregular poly(methyl methacrylate). V. Kinetics of initial template polymerization

The influence of stereoregular poly(methyl methacrylate) (PMMA) as a polymer matrix on the initial rate of radical polymerization of methyl methacrylate (MMA) has been measured between ?11 and +60°C using a dilatometric technique. Under proper conditions an increase in the relative initial rate of template polymerization with respect to a blank polymerization was observed. Viscometric studies showed that the observed effect could be related to the extent of complex formation between the polymer matrix and the growing chain radical. The initial rate was dependent on tacticity and molecular weight of the matrix polymer, solvent type and polymerization temperature. The accelerating effect was most pronounced (a fivefold increase in rate) at the lowest polymerization temperature with the highest molecular weight isotactic PMMA as a matrix in a solvent like dimethylformamide (DMF), which is known to be a good medium for complex formation between isotactic and syndiotactic PMMA. The acceleration of the polymerization below 25°C appeared to be accompanied by a large decrease in the overall energy and entropy of activation. It is suggested that the observed template effects are mainly due to the stereoselection in the propagation step (lower activation entropy Δ S_p^?) and the hindrance of segmental diffusion in the termination step (higher activation energy Δ E_t^?) of complexed growing chain radicals.     

Emulsion copolymerization of styrene and methyl methacrylate

Chain transfer constants to monomer have been measured by an emulsion copolymerization technique at 44°C. The monomer transfer constant (ratio of transfer to propagation rate constants) is 1.9 × 10^?5 for styrene polymerization and 0.4 × 10^?5 for the methyl methacrylate reaction. Cross-transfer reactions are important in this system; the sum of the cross-transfer constants is 5.8 × 10^?5. Reactivity ratios measured in emulsion were r₁ (styrene) = 0.44, r₂ = 0.46. Those in bulk polymerizations were r₁ = 0.45, r₂ = 0.48. These sets of values are not significantly different. Monomer feed compcsition in the polymerizing particles is the same as in the monomer droplets in emulsion copolymerization, despite the higher water solubility of methyl methacrylate. The equilibrium monomer concentration in the particles in interval-2 emulsion polymerization was constant and independent of monomer feed composition for feeds containing 0.25–1.0 mole fraction styrene. Radical concentration is estimated to go through a minimum with increasing methyl methacrylate content in the feed. Rates of copolymerization can be calculated a priori when the concentrations of monomers in the polymer particles are known.