增塑剂对PVA碱性聚合物电解质电化学性能的影响

通过溶解―铸膜法制备聚乙烯醇(PVA)-KOH-H2O碱性聚合物电解质膜。向聚合物中添加增塑剂丙三醇(GROL)和碳酸丙烯酯(PC)来提高离子电导率。X射线晶体衍射分析(XRD)结果表明,添加增塑剂未改变聚合物的物相结构,薄膜仍主要为不定形态。差示扫描热分析(DSC)结果显示,添加增塑剂后聚合物电解质膜的玻璃化转变温度降低,促进了电解质膜向不定形态转变。电解质膜室温离子电导率随增塑剂添加而增大,增塑剂超过一定量后离子电导率开始下降。PC对提高离子电导率的作用优于GROL。循环伏安测试结果显示,电解质膜的电化学稳定性窗口随增塑剂的添加而有所变窄,但仍显示了较好的电化学稳定性。     

Alkaline Stable Anion Exchange Membranes Based on Cross-Linked Poly(arylene ether sulfone) Bearing Dual Quaternary Piperidines for Enhanced Anion Conductivity at Low Water Uptake

Alkaline stable anion exchange membranes based on the cross-linked poly(arylene ether sulfone) grafted with dual quaternary piperidine (XPAES-DP) units were synthesized. The chemical structure of the synthesized PAES-DP was validated using ¹H-NMR and FT-IR spectroscopy. The physicochemical, thermal, and mechanical properties of XPAES-DP membranes were compared with those of two linear PAES based membranes grafted with single piperidine (PAES-P) unit and conventional trimethyl amine (PAES-TM). XPAES-DP membrane showed the ionic conductivity of 0.021 S cm⁻¹ at 40 °C which was much higher than that of PAES-P and PAES-TM because of the possession of more quaternary ammonium groups in the cross-linked structure. This cross-linked structure of the XPAES-DP membrane resulted in a higher tensile strength of 18.11 MPa than that of PAES-P, 17.09 MPa. In addition, as the XPAES-DP membrane shows consistency in the ionic conductivity even after 96 h in 3 M KOH solution with a minor change, its chemical stability was assured for the application of anion exchange membrane fuel cell. The single-cell assembled with XPAES-DP membrane displayed a power density of 109 mWcm⁻² at 80 °C under 100% relative humidity.     

Comb-shaped 2-Methylimidazolium Poly(arylene ether sulfone) Anion Exchange Membranes with High Alkaline Stability

A series of comb-shaped poly(arylene ether sulfone)s containing pendant 2-methyl-3-alkylimidazolitun group(ImPAES-Cx,x=1,6,10)was prepared and characterized as novel anion exchange membranes.These Im-PAES-Cx membranes were obtained by benzylic bromination and imidazolium functionalization.The characteristic nano-phase separation structure was formed in membranes with longer alkyl side chains,as confmned by small-angle X-ray scattering.The nano-phase separation structures endowed ImPAES-Cx membranes with improved ionic conductivity,dimensional stability(at least 60% decrease water uptake and swelling ratio at 60℃)and mechanical properties,together with excellent alkaline stability.Especially,ImPAES-C6 membranes possessed enhanced hydroxide conductivity and chemical stability simultaneously.These results suggest that it is a feasible strategy to introduce appropriate length of alkyl side chains into anion exchange membranes(AEMs)to improve the performance.     

Polymerization of 4-phenyl-1-butyne catalyzed by metathesis and Ziegler–Natta catalysts

The polymerization of 4-phenyl-1-butyne was carried out using metathesis and Ziegler-Natta catalysts. Especially, the Fe(acac)₃-AlEt₃ catalyst with toluene as a solvent produced an extremely high molecular weight polymer of M_w ≈ 10⁶. Solubility of the polymers at room temperature in organic solvents such as benzene, toluene, dichloromethane, chloroform, and THF was excellent despite their high molecular weights. It has been indicated that the polymer prepared by the Fe(acac)₃-AlEt₃ catalyst is of cis form with a high stereoregularity. © 1993 John Wiley & Sons, Inc.     

Peculiarities of Ethylene Polymerization Reactions with Heterogeneous Ziegler–Natta Catalysts: Kinetic Analysis

The previously developed kinetic scheme for olefin polymerization reactions with heterogeneous Ziegler–Natta catalysts states that the catalysts have several types of active centers which have different activities, different stabilities, produce different types of polymer materials, and respond differently to reaction conditions. In the case of ethylene polymerization reactions, each type of center exhibits an unusual chemical feature: a growing polymer chain containing one ethylene unit, Ti—C₂H₅, is unusually stable and can decompose with the formation of the Ti—H bond. This paper examines quantitative kinetic ramifications of this chemical mechanism. Modeling of the complex kinetics scheme described in the Scheme demonstrates that it correctly and quantitatively predicts three most significant peculiarities of ethylene polymerization reactions, the high reaction order with respect to the ethylene concentration, reversible poisoning with hydrogen, and activation in the presence of α‐olefins.     

Similarities and Differences of the Active Sites in Basic and Advanced MgCl2‐Supported Ziegler‐Natta Propylene Polymerization Catalysts

Though preparation procedures of heterogeneous Ziegler‐Natta catalysts for propylene polymerization are sophisticated, it is uncertain whether the nature of the active sites is similar or different for different preparation procedures. In this study, the effects of preparation procedures on the nature of the active sites were investigated by stopped‐flow polymerization in combination with microstructure analysis of polymers. Both basic and advanced types of catalysts showed the same two kinds of isospecific active site, which indicated little influence of the preparation method on the active site structure. On the contrary, the ratios of the two kinds of isospecific sites were not the same, resulting in variation of average polymer properties.

     

Multicenter nature of titanium‐based Ziegler–Natta catalysts: Comparison of ethylene and propylene polymerization reactions

This article discusses the similarities and differences between active centers in propylene and ethylene polymerization reactions over the same Ti‐based catalysts. These correlations were examined by comparing the polymerization kinetics of both monomers over two different Ti‐based catalyst systems, δ‐TiCl₃‐AlEt₃ and TiCl₄/DBP/MgCl₂‐AlEt₃/PhSi(OEt)₃, by comparing the molecular weight distributions of respective polymers, in consecutive ethylene/propylene and propylene/ethylene homopolymerization reactions, and by examining the IR spectra of “impact‐resistant” polypropylene (a mixture of isotactic polypropylene and an ethylene/propylene copolymer). The results of these experiments indicated that Ti‐based catalysts contain two families of active centers. The centers of the first family, which are relatively unstable kinetically, are capable of polymerizing and copolymerizing all olefins. This family includes from four to six populations of centers that differ in their stereospecificity, average molecular weights of polymer molecules they produce, and in the values of reactivity ratios in olefin copolymerization reactions. The centers of the second family (two populations of centers) efficiently polymerize only ethylene. They do not homopolymerize α‐olefins and, if used in ethylene/α‐olefin copolymerization reactions, incorporate α‐olefin molecules very poorly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1745–1758, 2003     

Propylene polymerization reactions with supported Ziegler–Natta catalysts: Observing polymer material produced by a single active center

Medium‐ and high‐resolution SEM analysis of several Ti‐based MgCl₂‐supported Ziegler–Natta catalysts and isotactic polypropylene produced with them is carried out. Each catalyst particle, 35–55 μ in size, produces one polymer particle with an average size of 1.5–2 mm, which replicates the shape of the catalyst particle. Polymer particles contain two distinct morphological features. The larger of them are globules with D_av ～400 nm; from 1 to 2 × 10¹¹ globules per particle. Each globule represents the combined polymer output of a single active center. The globules consist of ～2500 microglobules with an average size of ～20 nm. The microglobules contain several folded polymer molecules; they are the smallest thermodynamically stable macromolecular ensembles in propylene polymerization reactions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3832–3841     

Synthesis and Properties of Novel Side‐Chain Sulfonated Poly(Arylene Ether Sulfone)s for Proton Exchange Membranes

A series of novel side‐chain sulfonated poly(arylene ether sulfone) (SPAES) multiblock and random copolymers were synthesized by condensation polymerization from a new disulfonated aryl sulfone monomer, 4,4′‐difluoro‐2,2′‐bis(3‐sulfobenzoyl)diphenyl sulfone disodium salt (DFBSPS). The chemical structures of DFBSPS and the SPAESs were characterized by proton nuclear magnetic resonance (¹H NMR) and Fourier transform infrared (FTIR) spectra. The SPAES membranes prepared by solution cast method exhibited high tensile strength (50–71 MPa) and high radical oxidative stability. They could keep their morphology and maintain proton conductivities after hydrolysis test in 95 °C water for 1000 h. They also showed smaller swelling ratio in in‐plane direction than in through‐plane direction and such an anisotropic effect was more significant for the multiblock copolymers than for the random ones. The multiblock copolymer membranes exhibited higher proton conductivity than the random ones with similar ion exchange capacities (IECs). Preliminary hydrogen‐oxygen fuel cell tests were performed at 60 °C and 80% relative humidity (RH). The results showed that the single cell equipped with the multibiock copolymer membrane SB3 exhibited 0.12 W cm^?2 higher maximum output power density than the one equipped with the random copolymer membrane SR3 (with the same IEC), indicating much better performance of the former. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2304–2313     

Effects of external donors and hydrogen concentration on oligomer formation and chain end distribution in propylene polymerization with Ziegler‐Natta catalysts

The effect of type and concentration of external donor and hydrogen concentration on oligomer formation and chain end distribution were studied. Bulk polymerization of propylene was carried out with two different Ziegler‐Natta catalysts at 70 °C, one a novel self‐supported catalyst (A) and the other a conventional MgCl₂‐supported catalyst (B) with triethyl aluminum as cocatalyst. The external donors used were dicyclopentyl dimethoxy silane (DCP) and cyclohexylmethyl dimethoxy silane (CHM). The oligomer amount was shown to be strongly dependent on the molecular weight of the polymer. Catalyst A gave approximately 50 % lower oligomer content than catalyst B due to narrower molecular weight distribution in case of catalyst A. More n‐Bu‐terminated chain ends were found for catalyst A indicating more frequent 2,1 insertions. Catalyst A also gave more vinylidene‐terminated oligomers, suggesting that chain transfer to monomer, responsible for the vinylidene chain ends, was a more important chain termination mechanism for this catalyst, especially at low hydrogen concentration. Low site selectivity, due to low external donor concentration or use of a weak external donor (CHM), was also found to increase formation of vinylidene‐terminated oligomers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 351–358, 2010     

Supercritical Carbon Dioxide‐Treated Electrospun Poly(vinylidene fluoride) Nanofibrous Membranes: Morphology,Structures and Properties as an Ionic‐Liquid Host

A reverse‐barrier technique is used to enable the treatment of electrospun poly(vinylidene fluoride) nanofibrous membranes with supercritical carbon dioxide. The treatment induces the formation of nanopores and extended‐chain β crystallites of small lateral dimensions in the nanofibers. It also creates interfiber junctions, resulting in a remarkable improvement in mechanical properties of the membranes. The treated membranes are able to retain their shape very well after loading with an ionic liquid (IL). The ionic conductivity of the IL‐loaded membrane is very close to that of the neat IL.

     

Strong activation of MgCl2‐supported Ziegler‐Natta catalysts by treatments with BCl3: Evidence and application of the “cluster” model of active sites

Heterogeneous Ziegler‐Natta precatalysts (with phthalate as internal donor) were modified by treatments with BCl₃ (2 h in heptane; T = 20–90 °C; B/Ti = 0.1–5) before their use in the polymerization of propylene to modify the active sites distribution. If performed on previously “detitanated” precatalysts, the treatment leads to a strong increase of productivity (up to one order of magnitude) without drastic modifications of polypropylenes properties (tacticity, molecular weight distribution). In addition, these findings are in good agreement with the hypothesis of a “cluster” organization of active sites allowing to rationalize activation by BCl₃ by formation of heteronuclear B‐Ti clusters. The activation method was also applied to unmodified precatalysts and gave a significant gain of productivity. The simple and versatile activation process can also be performed under mild conditions (low T and low [BCl₃]). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5784–5791, 2009     

Isotactic Poly(propylene)/Monoalkylimidazolium‐Modified Montmorillonite Nanocomposites: Preparation by Intercalative Polymerization and Thermal Stability Study

Summary: Poly(propylene)/monoalkylimidazolium‐modified montmorillonite (PP/IMMT) nanocomposites were prepared by in situ intercalative polymerization of propylene with TiCl₄/MgCl₂/MMT catalyst. The PP synthesized possessed high isotacticity and molecular weight. Both wide‐angle X‐ray diffraction (XRD) and transmission electron microscopy (TEM) examinations evidenced the nanocomposite formation with exfoliated MMT homogeneously distributed in the PP matrix. A thermal stability study revealed that the nanocomposites possess good thermal stability.

X‐ray diffraction patterns of PP/IMMT (MMT = 2.2 wt.‐%) nanocomposite before and after processing.     

Synthesis of poly(p‐methoxyphenylacetylene) with the vanadium acetylacetonate‐aluminum triethyl Ziegler–Natta catalyst system: Cyclotrimers/polymer ratio analysis

Poly(p‐methoxyphenylacetylene) was obtained by the reaction of p‐methoxyphenylacetylene (MOPA) with the vanadium acetylacetonate‐aluminum triethyl V(acac)₃‐AlEt₃ homogeneous catalyst system. The crude product was always a mixture of 1,2,4‐ and 1,3,5‐tris(p‐methoxyphenyl)benzene and poly(MOPA) of low averaged molecular weight. The 1,2,4‐ and 1,3,5‐cyclotrimers versus poly(MOPA) ratio was analyzed. The poly(MOPA) obtained under different conditions, on the basis of the spectroscopic data, always shows a cis–transoidal stereo‐regular structure. Molecular mass of poly(MOPA) was determined by vapor pressure osmometry, high pressure liquid chromatography (HPLC), and gel permeation chromatography (GPC) techniques. The kinetics of the reaction has been also analyzed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5987–5997, 2005     

Exchange reactions occurring through active chain ends: Melt mixing of nylon 6 and polycarbonate

The chemical reactions occurring in the melt mixing of nylon6/polycarbonate (Ny6/PC) at 240°C were investigated. The reaction of equimolar Ny6/PC blends can be reconciled within the overall scheme of an exchange reaction occurring with the attack of active amino terminals on the inner carbonate groups. We have performed the synthesis of low molecular weight amino-terminated nylon 6 and the effect of the active amino terminal groups on the exchange kinetics was investigated. The exchange reaction yields sizeable amounts of copolymer, in fact after 75 min of melt mixing the (initially equimolar) blend contains 30 mol of unreacted PC and 70 mol of Ny6/PC copolymer (all the Ny6 was therefore incorporated in the copolymer). Trifluoroacetylation of nylon 6 was used to produce CHCl₃-soluble Ny6/PC copolymers, that could be analyzed by NMR. The NMR analysis yielded, beside the copolymer composition, evidence of the presence of urethane units interconnecting the Ny6 and PC blocks. The amount of urethane units increased with the reaction time, indicating a reduction of the block size as a function of the extent of exchange. Our study established the structure of the products formed, provided the materials balance of the process, and investigated some salient kinetic aspects. A thermal degradation study was also performed by thermogravimetry and direct pyrolysis mass spectrometry, to identify the products formed in the thermal treatment of the blends and to investigate the possible role of the inner amide groups in the intermolecular exchange reactions occurring between Ny6 and PC. Our results prove that these reactions occur above 300°C, and that only the cleavage of carbonate groups, by means of Ny6 amino end groups, is actually occurring at 240°C. © 1994 John Wiley & Sons, Inc.     

可逆加成-断裂链转移自由基聚合法合成梳型磺化聚醚醚酮

以带双硫酯取代基聚醚醚酮为大分子链转移剂, 采用可逆加成-断裂链转移自由基聚合(RAFT)法合成不同接枝率的磺化聚醚醚酮(g-SPEEK), 并对其结构进行表征. 在单体/链转移剂/引发剂的投料比(摩尔比)为50:4:1, 温度为70 ℃, 反应24 h, 得到聚合物膜的离子交换容量和吸水率分别为1.312 mmol/g和43.51%, 其溶胀率为5.05%, 低于Nafion膜的11.50%. 热重分析(TGA)结果表明该梳型g-SPEEK具有较好的热力学稳定性, 且该聚合物膜具有与Nafion膜相当的抗氧化性. 在相同的离子交换容量下, 梳型g-SPEEK比主链型SPEEK具有更好的H⁺离子透过性能.     

Synthesis and characterization of poly(arylene ether sulfone) copolymers with sulfonimide side groups for a proton‐exchange membrane

A sulfonimide‐containing comonomer derived from 4,4′‐dichlorodiphenylsulfone was synthesized and copolymerized with 4,4′‐dichlorodiphenylsulfone and 4,4′‐biphenol to prepare sulfonimide‐containing poly(arylene ether sulfone) random copolymers (BPSIs). These copolymers showed slightly higher water uptake than disulfonated poly(arylene ether sulfone) copolymer (BPSH) controls, but their proton‐conductivity values were very comparable to those of the BPSH series with similar ion contents. The proton conductivity increased with the temperature for both systems. For samples with 30 mol % ionic groups, BPSI showed less temperature dependence in proton conductivity and slightly higher methanol permeability in comparison with BPSH. The thermal characterization of the sulfonimide copolymers showed that both the acid and salt forms were stable up to 250 °C under a nitrogen atmosphere. The results suggested that the presumed enhanced stability of the sulfonimide systems did not translate into higher protonic conductivity in liquid water. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6007–6014, 2006     

Morphology and Electrical Conductivity of Poly(N‐vinylcarbazole)/Carbon Nanotubes Nanocomposite Synthesized by Solid State Polymerization

This communication describes the morphology and DC conductivity of poly(N‐vinylcarbazole) (PNVC)/multi‐walled carbon nanotubes (MWCNTs) nanocomposite. The nanocomposite has been synthesized by solid state in situ polymerization of N‐vinylcarbazole (NVC) monomer in the presence of MWCNTs at an elevated temperature. Fourier transform infrared (FT‐IR) spectroscopy studies reveal the ability of MWCNTs to promote the in situ polymerization of the NVC monomer. Field‐emission scanning electron microscopy (FE‐SEM) observations show the homogeneous wrapping of MWCNTs' outer surface by PNVC polymer. Transmission electron microscopy (TEM) images and Raman spectroscopy results support the SEM observations. Thermogravimetric analyses reveal a significant improvement of thermal stability of the nanocomposite sample in the higher temperature region. The resulting nanocomposite material exhibits a dramatic improvement of the DC conductivity inherent to the PNVC. For example, the DC conductivity increases from ≈5.9 × 10⁻¹³ S · cm⁻¹ for PNVC to ≈12 S · cm⁻¹ for the nanocomposite, an increase of about 10¹³ in the electrical conductivity.