Studies on the syntheses of polymetalloxanes and their properties as a precursor for amorphous oxide. V. Preparation and properties of polytitanosiloxanes from silicic acid and bis(2,4-pentanedionato)titanium diisopropoxide

Preparation and properties of polytitanosiloxanes (PTS) as a preceramic polymer for SiO₂-TiO₂ fibers were investigated. The PTS was prepared by the reaction of bis(2,4-pentanedionato) titanium diisopropoxide (PTP) with silicic acid (SA), extracted with tetrahydrofuran from an aqueous solution, in methanol. They were soluble in methanol, ethanol, and THF. The molecular weight (M_n ) was 1500–4200 depending on the reaction molar ratio (SA/PTP). A Concentrated methanol solution of PTS showed an appreciable stability to self-condensation and good spinnability. Dry spinning of the solution provided golden yellow precursor fibers which can be subjected to thermal-treatment to give ceramic fibers. The PTS is considered to be a copolymer formed by the condensation of oligomeric silicic acid with PTP consisting of Si? O? Ti and Si? O? Si linkages in the molecular main chain with the ligand and hydroxy groups as pendants.     

Synthesis of polytitanosiloxanes and their transformation to SiO2–TiO2 ceramic fibers

A one-pot synthesis of polytitanosiloxanes (PTS) and its transformation to SiO₂–TiO₂ ceramic fibers were investigated. PTS was prepared by the hydrolysis of tetraethoxysilane followed by the reaction with bis(2,4-pentanedionato)titanium diisopropoxide in methanol in 33–95 SiO₂ mol %. PTS was considered to be a ladder- or sheet-type polymer consisting of Si? O? Si and Si? O? Ti linkages as a main chain with pendant hydroxyl and 2,4-pentanedionato groups. SiO–TiO ceramic fibers were prepared by the pyrolysis of SiO₂–TiO₂ precursor fibers, which were prepared by the dry spinning of PTS followed by steam treatment. The tensile strength was 610 MPa for the SiO₂–TiO₂ fibers (SiO₂/TiO₂ = 20) after the pyrolysis at 700₀C. © 1994 John Wiley & Sons, Inc.     

Polymer precursor synthesis of alumina fibers

High strength alumina fibers were fabricated with a polymer precursor process which was monitored with ¹³C-NMR, elemental analysis, gas evolution, SEM, and X-ray diffraction. Methylaluminoxane was chain extended by reaction with H₂O, the unreacted methyl groups were converted to propanoyloxyl and i-propanoyl groups in molar ratios of 0.2 : 0.8 to 0.4 : 0.6 to afford spinning dope of adequate fluidity which can be spun into filaments with suitable stability. These precursor fibers were hydrolyzed in two stages at ambient temperatures and at 320–350°C, and then calcined at 950°C. The resulting alumina fibers have average tensile strengths up to 1.1 GPa and modulus of greater than 140 GPa.     

Carbon fibers prepared from tailored reversible‐addition‐fragmentation transfer copolymerization‐derived poly(acrylonitrile)‐co‐poly(methylmethacrylate)

Reversible‐addition fragmentation‐transfer (RAFT) polymerization of acrylonitrile (AN) was performed with 2‐(2‐cyano‐2‐propyl‐dodecyl)trithiocarbonate as RAFT agent and azobis(isobutyronitrile) as initiator. Linear polyacrylonitrile (M_n = 133,000 g/mol, PDI = 1.34) was prepared within 7 h in 86% isolated yield. High‐yield copolymerization with methyl methacrylate (MMA) was performed and copolymerization parameters were determined according to Kelen and Tüdös at 90 °C in ethylene carbonate yielding r_AN = 0.2 and r_MMA = 0.42. The molecular weights, polydispersity indices (PDIs), and MMA content of the copolymer were adjusted in a way that precursor fibers could be prepared via wet spinning. These precursor fibers had round cross‐sections and a dense morphology, showing tenacities of 40–50 cN/tex and elastic moduli of 900–1000 cN/tex at a fineness of 1 dtex and an elongation of 13–17%. Precursor fibers were oxidatively stabilized and then carbonized at different temperatures. A maximum tensile strength of 2.5 GPa was reached at 1350 °C. Thermal analysis, infrared and Raman spectroscopy, wide‐angle X‐ray scattering, scanning electron microscopy, and tensile testing were used to characterize the resulting carbon fibers. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1322–1333     

Investigation of IrO2/SnO2 thin film evolution by thermoanalytical and spectroscopic methods

The formation mechanism of thermally prepared IrO₂/SnO₂ thin films has been investigated under in situ conditions by thermogravimetry combined with mass spectrometry (TG-MS) and infrared emission spectroscopy (IRES). Mixtures of varying composition of the precursor salts (SnCl₂·2H₂O dissolved in ethanol and IrCl₃·3H₂O dissolved in isopropanol) were prepared onto titanium metal supports. Then the solvent was evaporated and the gel-like films were heated in an atmosphere containing 20% O₂ and 80% Ar to 600°C. The thermogravimetric curves showed that the evolution of the oxide phases take place in several decomposition stages and the final mixed oxide film is formed between 490 and 550°C, depending on the noble metal content. Mass spectrometric ion intensity curves revealed that below 200°C crystallization water, residual solvent, and hydrogen-chloride (formed as a result of an intramolecular hydrolysis) are liberated. The decomposition of surface species (surface carbonates, carbonyls and carboxylates) formed via the interaction of the residual solvent with the precursor salts takes place up to 450°C as evidenced by emission Fourier transform infrared spectrometry. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermal stability of anatase TiO2 aerogels

Titanium dioxide (TiO₂) aerogels were prepared with sol–gel ambient pressure drying method by using titanium tetrachloride (TiCl₄) as precursor and tetraethoxysilane as modifier, calcinated at different temperature and characterized by X‐ray diffraction, transmission electron microscopy and small angle X‐ray scattering. The results showed that the TiO₂ aerogels remained amorphous under 500 °C, changed to anatase from 600 °C and further changed to rutile from 900 °C. Between 60 °C and 500 °C, the primary particles within the samples concentrated mainly upon small sizes, enlarged and diverged remarkably above 600 °C. The crystalline grains grew and agglomerated with the rise of the calcination temperature. The TiO₂ aerogels at a temperature higher than 800 °C have better stability than anatase because of the formation of partial Ti―O―Si bonds. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation and properties characterization of gallic acid epoxy resin/succinic anhydride bionanocomposites modified by green reduced graphene oxide

Graphene oxide was reduced into reducing-graphene oxide (r-GO) successfully using gallic acid (GA) as a green reducing agent. Biobased gallic acid epoxy resin (GAER) was synthesized from renewable GA, and the biobased GAER/r-GO nanocomposites and glass fiber-reinforced composites were prepared with succinic anhydride as a curing agent. The dynamic mechanical, thermal, and mechanical properties of the composites with varying r-GO contents were characterized. When the content of r-GO was 0.5 wt%, the glass transition temperature was 10.4°C higher than the pure resin system. The thermal and mechanical properties were increased with increasing r-GO content; when the r-GO content was 1.0 wt%, the initial degradation temperature was enhanced by approximately 6.8°C, the tensile and impact strengths were 34.5% and 49.1% higher, respectively, than the pure cured GAER. The impact strength of GAER was higher than that of the bisphenol A epoxy resin/SUA curing system, but the tensile strength was lower than it.     

Coating of anatase titania on clinoptilolite by metal organic chemical vapor deposition method: enhanced mesoporosity and photocatalytic activity

Clinoptilolite-supported TiO₂ (TiO₂/CP_MOCVD) has been synthesized by metal organic chemical vapor deposition method (MOCVD). Titanium precursor was evaporated at 110 °C under nitrogen flow rate to promote the surface interaction between titanium species and clinoptilolite. The effect of titanium precursor on the crystalline structure and the surface area of clinoptilolite were investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), transformed infrared spectroscopy (FT-IR), Raman spectroscopy, and Brunauer–Emmett–Teller measurement. XRD and SEM results indicate that TiO₂ precursor interacted with the support, decreasing the crystallinity of the clinoptilolite. The analysis by FT-IR spectroscopy further confirms that the titanium species were bound to clinoptilolite through Ti–O–Si bonds. The TiO₂/CP_MOCVD catalyst showed a mesoporous structure with the distribution of pores in several dimensions 3.7–7.1 nm, with high specific surface area (~ 471 m²/g). MOCVD improved the adsorption capacity of the catalyst surface towards the pollutants. TiO₂/CP_MOCVD particles turn yellow after adsorption of salicylic acid. The development of the yellow color is a clear indication of the formation of charge transfer titanium (IV) salicylate surface complex. Photocatalytic decomposition of SA in aqueous solution was carried out using TiO₂/CP_MOCVD. Experimental results revealed that TiO₂/CP_MOCVD required shorter irradiation time (120 min) for complete decomposition of SA than commercial P25 Degussa and TiO₂/CP_imp (clinoptilolite-supported TiO₂ using impregnation method). The TiO₂/CP_MOCVD can be recycled at least four times without loss in activity, indicating their magnificent stability.     

Investigation of RuO2-IrO2-SnO2 thin film evolution

The thermal evolution process of RuO₂–IrO₂–SnO₂ mixed oxide thin films of varying noble metal contents has been investigated under in situ conditions by thermogravimetry-mass spectrometry (TG-MS), infrared emission spectroscopy (IR) and cyclic voltammetry (CV). The gel-like films prepared from aqueous solutions of the precursor compounds RuOHCl₃, H₂IrCl₆ and Sn(OH)₂(CH₃COO)_2–xCl_x on titanium metal support were heated in an atmosphere containing 20% O₂ and 80% Ar up to 600°C. Chlorine evolution takes place in a single step between 320 and 500°C accompanied with the decomposition of the acetate ligand. The decomposition of surface species formed like carbonyls, carboxylates and carbonates occurs in two stages between 200 and 500°C. The temperature of chlorine evolution and that of the final film formation increases with the increase of the iridium content in the films. The anodic peak charge shows a maximum value at 18% iridium content.     

Synthesis and properties of titanium glycolate Ti(OCH2CH2O)2

A new efficient method for the synthesis of extended micro-and nano-sized crystals (whiskers, fibers) of titanium glycolate Ti(OCH₂CH₂O)₂ has been suggested. The method implies the reaction of hydrated titanium dioxide with ethylene glycol on heating in air. Thermolysis of Ti(OCH₂CH₂O)₂ in air gives titanium dioxide as anatase (400–500°C) and rutile (T > 700°C), the morphology of titanium glycolate crystals being inherited by the oxide. The pseudocrystals of the thermolysis product in an inert gas medium (T = 500–950°C) represent aglomeration of nano-sized titanium dioxide particles and amorphous carbon. At temperatures up to 1300°C, the formation of the TiO_2?x C _x phase with a rutile structure is probable. In a wet air environment, titanium glycolate is partially hydrolyzed to give TiO _x (OCH₂CH₂O)_2?2x (OH)_2x ·xH₂O (0 ≤ x ≤ 1) and on keeping in water at room temperature, ethylene glycol is completely displaced from the crystals. This process is also not accompanied by changes in the particle morphology.     

High‐performance poly(ethylene‐2,6‐naphthalate) fiber prepared by high‐tension annealing

A high‐tension annealing (HTA) method has been applied to zone‐annealed poly(ethylene‐2,6‐naphthalate) (PEN) fibers in order to further improve their mechanical properties. The HTA treatment was carried out under an applied tension of 428 MPa at a treating temperature of 175 °C. The applied tension was close to the tensile strength at 175 °C. The resulting HTA fiber had a birefringence of 0.492 and degree of crystallinity of 57%. Wide‐angle X‐ray diffraction (WAXD) photographs of the HTA fibers showed three reflections (010, 100, and 1 10) attributed to an α form crystal, but no (020) reflection attributed to a β form was observed in the equator. The tensile modulus and tensile strength increased with processing, and the HTA fiber had a maximum modulus of 33 GPa, a tensile strength of 1.1 GPa, and a storage modulus of 33 GPa at 25 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 61–67, 2000     

Superdrawing of polytetrafluoroethylene nascent powder by solid‐state coextrusion

A film of nascent powder of polytetrafluoroethylene (PTFE), compacted below the ambient melting temperature (T_m, 335 °C), was drawn by two‐stage draw techniques consisting of a first‐stage solid‐state coextrusion followed by a second‐stage solid‐state coextrusion or tensile draw. Although the ductility of extrudates was lost for the second‐stage tensile draw at temperatures above 150 °C due to the rapid decrease in strength, as previously reported, the ductility of extrudates increased with temperature even above 150 °C when the second‐stage draw was made by solid‐state coextrusion, reflecting the different deformation flow fields in a free space for the former and in an extrusion die for the latter. Thus, a powder film initially coextruded to a low extrusion draw ratio (EDR) of 6–20 at 325 °C was further drawn by coextrusion to EDRs up to ～?400 at 325–340 °C, near the T_m. Extremely high chain orientation (f_c = 0.998 ± 0.001), crystallinity (96.5 ± 0.5)%, and tensile modulus (115 ± 5 GPa at 24 °C, corresponding to 73% of the X‐ray crystal modulus) were achieved at high EDRs. Despite such a morphological perfection and a high modulus, the tensile strength of a superdrawn tape, 0.48 ± 0.03 GPa, was significantly low when compared with those (1.4–2.3 GPa) previously reported by tensile drawing above the T_m. Such a low strength of a superdrawn, high‐modulus PTFE tape was ascribed to the low intermolecular interaction of PTFE and the lack of intercrystalline links along the fiber axis, reflecting the initial chain‐extended morphology of the nascent powder combined with the fairly high chain mobility associated with the crystal/crystal transitions at around room temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3369–3377, 2006     

Carbonized fibers based on polyvinyl alcohol

On the basis on polyvinyl alcohol (PVA), carbonized fibers were produced in the form of a complex technical thread with tensile strength above 200 MPa and specific electrical conductivity of at least 0.5 S/cm. Using thermogravimetric and differential thermal analysis, Raman scattering, and wide-angle X-ray diffraction, structures of these fibers were characterized. The structural parameters of carbonized PVA fibers are close to the parameters of carbonized coal tar pitch obtained by heat treatment at 1000°C. The structure and properties of carbonized fibers modified with potassium bisulfate were also studied.     

1:1 alternating copolymer of acrylonitrile and vinyl acetate

Copolymerization of the acrylonitrile-zinc chloride complex with excess vinyl acetate has been investigated. Alternating 1:1 copolymers of acrylonitrile and vinyl acetate of high molecular weights have been successfully prepared. The alternating structure has been ascertained by means of high-resolution nuclear magnetic resonance spectroscopy. The copolymer is amorphous (T_g = 85°C) and has shown thermal and oxidative stability better than those of polyacrylonitrile. The copolymer is soluble in acetone as well as in more powerful solvents such as dimethylformamide, dimethyl sulfoxide, nitromethane, and N-methylpyrrolidone. The copolymer has been processed into films and fibers from its acetone solutions. Films show tensile properties similar to those of cellulose acetate under ambient conditions; they suffer drastic loss in tensile properties at above 50°C and retain their good tensile properties at subzero temperatures (determined as low as ?40°C). Fibers show tensile properties comparable to those of modacrylic fibers under ambient conditions but suffer marked loss in stiffness at 40°C in water and 60°C in air. The fibers also retain their good properties at subzero temperatures (measured down to ?60°C).     

Evaluation of Mechanical Properties of Epoxy/Nanoclay/Multi-Walled Carbon Nanotube Nanocomposites using Taguchi Method

This paper reports the improvement of the mechanical properties of epoxy/nanoclay/multi-walled carbon nanotube (MWNT) nanocomposites prepared by the solution casting method for a range of pre-cure temperatures (room temperature, 50, and 70 °C), cure temperature (120, 130, and 140 °C), nanoclay content (0.5, 1.0, 1.5 wt%) and content of MWNT (0.2, 0.6, 1.0 wt%) for three levels. The influence of these parameters on the mechanical properties of epoxy/nanoclay/MWNT has been investigated using Taguchi's experimental design. The output measured responses are the tensile properties (tensile modulus, tensile strength and strain at break), impact strength and fracture toughness. From the Analysis of Mean (ANOM) and Analysis of Variance (ANOVA), MWNT content, pre-cure temperature and cure temperature had the most significant effects for the impact strength with contribution percentages of 38%, 28% and 23% respectively. However, for the fracture toughness and strain at break, the enhancements of properties come from the nanoclay content (59%), MWNT content (18%) and pre-cure temperature (23%). While the improvement in tensile strength was influenced by nanoclay and MWNT content, the cure temperature has a stronger effect on the tensile modulus. In this respect, Taguchi method points to the Taguchi method, in this way, points to the dominant parameters and gives the optimum parameter settings for each mechanical property. Confirmation experiments were performed with the optimum parameter settings and the mechanical properties were measured compared with the predicted results.     

Morphological and mechanical properties of nascent polyethylene fibers produced via ethylene extrusion polymerization with a metallocene catalyst supported on MCM‐41 particles

Polyethylene (PE) fibers were prepared by ethylene extrusion polymerization with an MCM‐41‐supported titanocene catalyst. The morphological and mechanical properties of these nascent PE fibers were investigated. Three levels of fibrous morphologies were identified in the fiber samples through an extensive scanning electron microscopy study. Extended‐chain PE nanofibrils with diameters of about 60 nm were the major morphological units present in the fiber structure. The nanofibrils were parallel‐packed into individual microfibers with diameters of about 1–30 μm. The microfibers were further aggregated irregularly into fiber aggregates and bundles. In comparison with commercial PE fibers and data reported in the literature, the individual microfibers produced in situ via ethylene extrusion polymerization without posttreatment exhibited a high tensile strength (0.3–1.0 GPa), a low tensile modulus (3.0–7.0 GPa), and a high elongation at break (8.5–20%) at 35 °C. The defects in the alignment of the nanofibrils were believed to be the major reason for the low modulus values. It was also found that a slight tensile drawing could increase the microfiber strength and modulus. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2433–2443, 2003     

Preparation and characterization of functionalized graphene oxide/carbon fiber/epoxy nanocomposites

Graphene oxide (GO) was functionalized using three different diamines, namely ethylenediamine (EDA), 4,4′-diaminodiphenyl sulfone (DDS) and p-phenylenediamine (PPD) to reinforce an epoxy adhesive, with the aim of improving the bonding strength of carbon fiber/epoxy composite. The chemical structure of the functionalized GO (FGO) nanosheets was characterized by elemental analysis, FT-IR and XRD. Hand lay-up, as a simple method, was applied for 3-ply composite fabrication. In the sample preparation, the fiber-to-resin ratio of 40:60 (w:w) and fiber orientations of 0°, 90°, and 0° were used. The GO and FGO nanoparticles were first dispersed in the epoxy resin, and then the GO and FGO reinforced epoxy (GO- or FGO-epoxy) were directly introduced into the carbon fiber layers to improve the mechanical properties. The GO and FGO contents varied in the range of 0.1–0.5 wt%. Results showed that the mechanical properties, in terms of tensile and flexural properties, were mainly dependent on the type of GO functionalization followed by the percentage of modified GO. As a result, both the tensile and flexural strengths are effectively enhanced by the FGOs addition. The tensile and flexural moduli are also increased by the FGO filling in the epoxy resin due to the excellent elastic modulus of FGO. The optimal FGO content for effectively improving the overall composite mechanical performance was found to be 0.3 wt%. Scanning electron microscopy (SEM) revealed that the failure mechanism of carbon fibers pulled out from the epoxy matrix contributed to the enhancement of the mechanical performance of the epoxy. These results show that diamine FGOs can strengthen the interfacial bonding between the carbon fibers and the epoxy adhesive.     

Optimization and statistical analysis of Au-ZnO/Al2O3 catalyst for CO oxidation

In our former work [Catal. Today 174 (2011) 127], 12 heterogeneous catalysts were screened for CO oxidation, and Au-ZnO/Al₂O₃ was chosen and optimized in terms of weight loadings of Au and ZnO. The present study follows on to consider the impact of process parameters (catalyst preparation and reaction conditions), in conjunction with catalyst composition (weight loadings of Au and ZnO, and the total weight of the catalyst), as the optimization of the process parameters simultaneously optimized the catalyst composition. The optimization target is the reactivity of this important reaction. These factors were first optimized using response surface methodology (RSM) with 25 experiments, to obtain the optimum: 100 mg of 1.0%Au-4.1%ZnO/Al₂O₃ catalyst with 220 °C calcination and 100 °C reduction. After optimization, the main effects and interactions of these five factors were studied using statistical sensitivity analysis (SA). Certain observations from SA were verified by reaction mechanism, reactivity test and/or characterization techniques, while others need further investigation.     

Polyimides containing carbonyl and ether connecting groups. II

In a continuation of our effort on polyimides containing carbonyl and ether connecting groups between aromatic rings, several new polyimides were prepared and characterized. A few of these polymers were semi-crystalline. Glass transition temperatures ranged from 164 to 258°C and crystalline melt temperatures were observed between 350 and 424°C. The semi-crystalline polyimide from the reaction of 3,3′,4,4′-benzophenonetetracarboxylic dianhydride and 1,3-bis(4-aminophenoxy-4′-benzoyl)benzene provided transparent orange films with excellent tensile properties, exceptional resistance to solvents and strong base, and high thermooxidative stability. In addition, this polyimide provided excellent adhesive strength for joining titanium (6A1–4V) to titanium.     

Influence of finishing oil on structure and properties of multi-filament fibers from cellulose dope in NaOH/urea aqueous solution

Cellulose multi-filament fibers have been spun successfully on a pilot plant scale, from a cellulose dope in 7 wt% NaOH/12 wt% urea aqueous solution pre-cooled to −12 °C. Coagulation was accomplished in a bath with 10 wt% H₂SO₄/12 wt% Na₂SO₄ and then 5 wt% H₂SO₄ aqueous solution. By using different finishing oil, including H₂O, 4% glycerol aqueous solution, 2% polyvinyl alcohol (PVA) aqueous solution, 2% polyethylene glycol octyl phenylether (OP) aqueous solution, mobol and 2%glycerol/1%PVA/1%OP aqueous solution (PGO), we prepared six kinds of the cellulose multi-filaments, with tensile strength of 1.7–2.1 cN/dtex. Their structure and properties were investigated with scanning electron microscope (SEM), ¹³C NMR solid state, wide-angle X-ray diffraction (WAXD) and tensile testing. The cellulose fibers treated with PGO possessed higher mechanical properties and better surface structure than others. Interestingly, although the orientation of the cellulose multi-filaments is relatively low, the tensile strength of the single-fiber was similar to that of Lyocell. It was worth noting that the dyeability of the multi-filament fibers was superior to viscose rayon.