Herein, the assembly of CsPbBr3 QD/AlOx inorganic nanocomposites, by using atomic layer deposition (ALD) for the growth of the amorphous alumina matrix (AlOx ), is described as a novel protection scheme for such QDs. The nucleation and growth of AlOx on the QD surface was thoroughly investigated by miscellaneous techniques, which highlighted the importance of the interaction between the ALD precursors and the QD surface to uniformly coat the QDs while preserving the optoelectronic properties. These nanocomposites show exceptional stability towards exposure to air (for at least 45 days), irradiation under simulated solar spectrum conditions (for at least 8 h), and heat (up to 200 °C in air), and finally upon immersion in water. This method was extended to the assembly of CsPbBrx I3−x QD/AlOx and CsPbI3 QD/AlOx nanocomposites, which were more stable than the pristine QD films. 相似文献
Encapsulation methods have shown to be effective in imparting improved stability to metal-halide perovskite nanocrystals (NCs). Atomic layer deposition (ALD) of metal oxides is one of the promising approaches for such encapsulation, yet better control on the process parameters are required to achieve viable lifetimes for several optoelectronic and photocatalytic applications. Herein, we optimize the ALD process of amorphous aluminum oxide (AlOx) as an encapsulating layer for CsPbBr3 NC thin films by using oxygen (O2) as a molecular diffusion probe to assess the uniformity of the deposited AlOx layer. When O2 reaches the NC surface, it extracts the photogenerated electrons, thus quenching the PL of the CsPbBr3 NCs. As the quality of the ALD layer improves, less quenching is expected. We compare three different ALD deposition modes. We find that the low temperature/high temperature and the exposure modes improve the quality of the alumina as a gas barrier when compared with the low temperature mode. We attribute this result to a better diffusion of the ALD precursor throughout the NC film. We propose the low temperature/high temperature as the most suitable mode for future implementation of multilayered coatings. 相似文献
Cesium lead halide perovskites are an emerging class of quantum dots (QDs) that have shown promise in a variety of applications; however, their properties are highly dependent on their surface chemistry. To this point, the thermodynamics of ligand binding remain unstudied. Herein, 1H NMR methods were used to quantify the thermodynamics of ligand exchange on CsPbBr3 QDs. Both oleic acid and oleylamine native ligands dynamically interact with the CsPbBr3 QD surface, having individual surface densities of 1.2–1.7 nm?2. 10‐Undecenoic acid undergoes an exergonic exchange equilibrium with bound oleate (Keq=1.97) at 25 °C while 10‐undecenylphosphonic acid undergoes irreversible ligand exchange. Undec‐10‐en‐1‐amine exergonically exchanges with oleylamine (Keq=2.52) at 25 °C. Exchange occurs with carboxylic acids, phosphonic acids, and amines on CsPbBr3 QDs without etching of the nanocrystal surface; increases in the steady‐state PL intensities correlate with more strongly bound conjugate base ligands. 相似文献
An ordered self‐assembly of CsPbBr3 quantum dots (QDs) was generated on the surface of few‐layer black phosphorus (FLBP). Strong quenching of the QD fluorescence was observed, and analyzed by time‐resolved photoluminescence (TR‐PL) studies, DFT calculations, and photoconductivity measurements. Charge transfer by type I band alignment is suggested to be the cause of the observed effects. 相似文献
Controllable self-assembly and properties of nanocomposites based on CdSe/ZnS semiconductor quantum dots (QDs) and tetrapyridylporphyrin molecules (H2P) as well as the dynamics of relaxation processes in these systems were studied for solutions and single nanoobjects in the temperature range of 77–295 K. It was proved that the formation of surface states of different nature is crucial to nonradiative relaxation of exciton excitation in QDs. The efficiency of QD→Н2Р energy transfer was shown to be at most 10–15%. Regularities of photoluminescence (PL) quenching for QDs in nanocomposites in solutions of different polarity correlate with the dependences of PL blinking for single QDs. A scheme was proposed of excited states and main relaxation channels of exciton excitation energy in semiconductor QDs and QD–Н2Р nanocomposites. 相似文献
We successfully prepared QDs incorporated into a silica/alumina monolith (QDs‐SAM) by a simple sol–gel reaction of an Al–Si single precursor with CsPbBr3 QDs blended in toluene solution, without adding water and catalyst. The resultant transparent monolith exhibits high photoluminescence quantum yields (PLQY) up to 90 %, and good photostability under strong illumination of blue light for 300 h. We show that the preliminary ligand exchange of didodecyl dimethyl ammonium bromide (DDAB) was very important to protect CsPbBr3 QDs from surface damages during the sol–gel reaction, which not only allowed us to maintain the original optical properties of CsPbBr3 QDs but also prevented the aggregation of QDs and made the monolith transparent. The CsPbBr3 QDs‐SAM in powder form was easily mixed into the resins and applied as color‐converting layer with curing on blue light‐emitting diodes (LED). The material showed a high luminous efficacy of 80 lm W−1 and a narrow emission with a full width at half maximum (FWHM) of 25 nm. 相似文献
All inorganic CsPbBr3 perovskite quantum dots (QDs) are potential emitters for electroluminescent displays. We have developed a facile hot‐injection method to partially replace the toxic Pb2+ with highly stable Sn4+. Meanwhile, the absolute photoluminescence quantum yield of CsPb1−x Snx Br3 increased from 45 % to 83 % with SnIV substitution. The transient absorption (TA) exciton dynamics in undoped CsPbBr3 and CsPb0.67Sn0.33Br3 QDs at various excitation fluences were determined by femtosecond transient absorption, time‐resolved photoluminescence, and single‐dot spectroscopy, providing clear evidence for the suppression of trion generation by Sn doping. These highly luminescent CsPb0.67Sn0.33Br3 QDs emit at 517 nm. A device based on these QDs exhibited a luminance of 12 500 cd m−2, a current efficiency of 11.63 cd A−1, an external quantum efficiency of 4.13 %, a power efficiency of 6.76 lm w−1, and a low turn‐on voltage of 3.6 V, which are the best values among reported tin‐based perovskite quantum‐dot LEDs. 相似文献
Halide perovskite quantum dots (QDs) have great potential in photocatalytic applications if their low charge transportation efficiency and chemical instability can be overcome. To circumvent these obstacles, we anchored CsPbBr3 QDs (CPB) on NHx‐rich porous g‐C3N4 nanosheets (PCN) to construct the composite photocatalysts via N?Br chemical bonding. The 20 CPB‐PCN (20 wt % of QDs) photocatalyst exhibits good stability and an outstanding yield of 149 μmol h?1 g?1 in acetonitrile/water for photocatalytic reduction of CO2 to CO under visible light irradiation, which is around 15 times higher than that of CsPbBr3 QDs. This study opens up new possibilities of using halide perovskite QDs for photocatalytic application. 相似文献
For emerging perovskite quantum dots (QDs), understanding the surface features and their impact on the materials and devices is becoming increasingly urgent. In this family, hybrid FAPbI3 QDs (FA: formamidium) exhibit higher ambient stability, near-infrared absorption and sufficient carrier lifetime. However, hybrid QDs suffer from difficulty in modulating surface ligand, which is essential for constructing conductive QD arrays for photovoltaics. Herein, assisted by an ionic liquid formamidine thiocyanate, we report a facile surface reconfiguration methodology to modulate surface and manipulate electronic coupling of FAPbI3 QDs, which is exploited to enhance charge transport for fabricating high-quality QD arrays and photovoltaic devices. Finally, a record-high efficiency approaching 15 % is achieved for FAPbI3 QD solar cells, and they retain over 80 % of the initial efficiency after aging in ambient environment (20–30 % humidity, 25 °C) for over 600 h. 相似文献
Herein, we designed four peptides appended with different numbers of histidine (Hisn‐peptide). We launched a systematic investigation on quantum dots (QDs) and Hisn‐peptide self‐assembly in solution using fluorescence coupled CE (CE‐FL). The results indicated that CE‐FL was a powerful method to probe how ligands interaction on the surface of nanoparticles. The self‐assembly of QDs and peptide was determined by the numbers of histidine. We also observed that longer polyhistidine tags (n ≤ 6) could improve the self‐assembly efficiency. Furthermore, the formation and separation of QD‐peptide assembly were also studied by CE‐FL inside a capillary. The total time for the mixing, self‐assembly, separation, and detection was less than 10 min. Our method greatly expands the application of CE‐FL in QDs‐based biolabeling and bioanalysis. 相似文献
Bidentate chelation, meso‐2,3‐dimercaptosuccinic acid (DMSA), was used as a stabilizer for the synthesis of CdTe quantum dots (QDs). The bidentate chelate QDs, characterized with FT‐IR, PL, and UV/Vis spectroscopy; element analysis; and high‐resolution transmission electron microscope, exhibited surface traps due to the large surface/volume ratio of QD particle and the steric hindrance of the DMSA molecule. The unpassivated surface of the QDs produced a narrower band gap than the core and electrochemiluminescent (ECL) emission at relatively low cathodic potential. In air‐saturated pH 7.0 buffer, the QDs immobilized on electrode surface showed an intense ECL emission peak at ?0.85 V (vs. Ag/AgCl). H2O2 produced from electrochemical reduction of dissolved oxygen was demonstrated to be the co‐reactant, which avoided the need of strong oxidant as the co‐reactant and produced a sensitive analytical method for peroxidase‐related analytes. Using hydroquinone/horseradish peroxidase/H2O2 as a model system, a new, reagentless, phenolic, ECL biosensor for hydroquinone was constructed, based on the quenching effect of ECL emission of QDs by consumption of co‐reactant H2O2. The biosensor showed a linear range of 0.2–10 μM with acceptable stability and reproducibility. This work opens new avenues in the search for new ECL emitters with excellent analytical performance and makes QDs a more attractive alternative in biosensing. 相似文献
We demonstrate the formation of one-, two-, and three-dimensional nanocomposites through the self-assembly of silanized CdSe/ZnS quantum dots (QDs) by using a controlled sol-gel process. The self-assembly behavior of the QDs was created when partially hydrolyzed silicon alkoxide monomers replaced hydrophobic ligands on the QDs. We examined systematically self-assembly conditions such as solvent components and QD sizes in order to elucidate the formation mechanism of various QD nanocomposites. The QD nanocomposites were assembled in water phase or on the interface of water and oil phase in emulsions. The partially hydrolyzed silicon alkoxides act as intermolecules to assemble the QDs. The QD nanocomposites with well-defined solid or hollow spherical, fiber-like, sheet-like, and pearl-like morphologies were prepared by adjusting the experimental conditions. The high photoluminescence efficiency of the prepared QD nanocomposites suggests partially hydrolyzed silicon alkoxides reduced the surface deterioration of QDs during self-assembly. These techniques are applicable to other hydrophobic QDs for fabricating complex QD nanocomposites. 相似文献
Silica-coated magnetic polystyrene nanospheres (MPN) containing CdTe/CdS quantum dots (QDs) and Fe3O4 nanoparticles were prepared, and novel anti-EGFR antibodies were conjugated onto these magneto-fluorescent nanocomposites
(MPN–QDs–SiO2) for cancer cell targeting, imaging and collection. Transmission electron microscopy (TEM), scanning electron microscopy
(SEM) images and energy-dispersive x-ray spectrometry (EDS) data showed that the MPN had been successfully coated with QDs
and a silica shell, and the nanocomposites obtained with negative charged surfaces were well dispersed. The bioconjugates
could be used for specifically labeling and separating cancer cells (MDA-MB-435S, SMMC-7721), but did not recognize and separate
the K562 cells because the human epidermal growth factor receptor (EGFR) was not expressed on the surface. Because the anti-EGFR
antibody, which we have developed, could specifically recognize certain cancer cells that highly expressed EGFR on their surface,
these nanoscale bioconjugates, synchronously exhibiting fluorescence and magnetism, may be used in novel bioprobes for labeling
and collecting rare cancer cells, which may be beneficial for early cancer diagnosis. 相似文献
This paper describes a method for producing silica particles containing multiple quantum dots (QD/SiO2), a method for surface-modifying the particles with poly(ethylene glycol) (QD/SiO2/PEG), and an in vivo fluorescence imaging technique using colloid solution of the QD/SiO2/PEG particles. The QDs used were ZnS-coated CdSexTe1?x nanoparticles surface-modified with carboxyl groups, and had an average size of 10.3 ± 2.1 nm. The QD/SiO2 particles were fabricated by performing sol–gel reaction of tetraethyl orthosilicate using NaOH as a catalyst in the presence of the QDs. The produced particles formed core–shell structure composed of multiple QDs and silica shell, and had an average size of 50.2 ± 17.9 nm. Surface-modification of the QD/SiO2 particles with PEG, or PEGylation of the particle surface, was performed by using methoxy polyethylene glycol silane. Fluorescence of QD colloid solution was not quenched even through the silica-coating and the PEGylation. Tissues of a mouse could be imaged by injecting the concentrated colloid solution into it and measuring fluorescence intensity emitted from the tissues. 相似文献
The atomic layer deposition (ALD) of iron sulfide (FeSx ) is reported for the first time. The deposition process employs bis(N ,N′ ‐di‐tert‐butylacetamidinato)iron(II) and H2S as the reactants and produces fairly pure, smooth, and well‐crystallized FeSx thin films following an ideal self‐limiting ALD growth behavior. The FeSx films can be uniformly and conformally deposited into deep narrow trenches with aspect ratios as high as 10:1, which highlights the broad applicability of this ALD process for engineering the surface of complex 3D nanostructures in general. Highly uniform nanoscale FeSx coatings on porous γ‐Al2O3 powder were also prepared. This compound shows excellent catalytic activity and selectivity in the hydrogenation of azo compounds under mild reaction conditions, demonstrating the promise of ALD FeSx as a catalyst for organic reactions. 相似文献
All-inorganic perovskite quantum dots (QDs) have attracted great interests due to its outstanding properties. But their poor stability in polar solvents seriously hampered wide applications in analytical chemistry. In this work, strong, stable and flexibly regulated the electrochemiluminescence (ECL) emission form CsPbBr3 QDs was successfully obtained and applied in the analysis of polar solvents through the unique structure of closed bipolar electrode (BPE). To demonstrate the feasibility, it was successfully used in the detection of tetracycline (Tc) aqueous solution. CsPbBr3 QDs was immersed into organic solution in anode microcell of closed BPE while Tc aqueous solution was added into cathode microcell. The two microcells were physically separated and would not interfere with each other. But the bio-recognition event between aptamer and Tc in cathode microcell would induce the ECL signal change in anode microcell through the electrons conducted by BPE as the bridge. The ECL emission can be flexibly regulated by environmental factors of both polar and non-polar solvents and the interface status of the BPE. Compared with traditional methods to overcome the intrinsic instability in polar medium, the reported method does not need any further surface modifications, has no limitations on the targets and can provide wide development space for further deep research, which may open a new direction for the ECL sensing of CsPbBr3 QDs. 相似文献
The assembly kinetics of colloidal semiconductor quantum dots (QDs) on solid inorganic surfaces is of fundamental importance for implementation of their solid-state devices. Herein an inorganic binding peptide, silica binding QBP1, was utilized for the self-assembly of nanocrystal quantum dots on silica surface as a smart molecular linker. The QD binding kinetics was studied comparatively in three different cases: first, QD adsorption with no functionalization of substrate or QD surface; second, QD adsorption on QBP1-modified surface; and, finally, adsorption of QBP1-functionalized QD on silica surface. The surface modification of QDs with QBP1 enabled 79.3-fold enhancement in QD binding affinity, while modification of a silica surface with QBP1 led to only 3.3-fold enhancement. The fluorescence microscopy images also supported a coherent assembly with correspondingly increased binding affinity. Decoration of QDs with inorganic peptides was shown to increase the amount of surface-bound QDs dramatically compared to the conventional methods. These results offer new opportunities for the assembly of QDs on solid surfaces for future device applications. 相似文献
We report on a widely applicable approach for protein detection by using triple-helix DNA mediated CuInS2 quantum dot (QD) and graphene oxide (GO) nanocomposite. The CuInS2 QDs were coated with mercaptopropionic acid and then covalently linked to a hairpin aptamer against lysozyme (HLA). Single-stranded DNA (triple helix-forming oligonucleotide; THFO) readily absorbs on the surface of GO via π-stacking interaction, and this results in the formation of THFO-GO. If HLA-CuInS2 QDs are added to the THFO-GO system, the fluorescence of HLA-CuInS2 QDs (at excitation/emission wavelengths of 590/665 nm) is quenched. Lysozyme has a higher affinity for HLA than THFO. Therefore, in the presence of lysozyme, it will bind to the HLA-CuInS2 QD and displace the THFO-GO. This results in the restoration of fluorescence that is related to the concentration of lysozyme. The fluorescence of the QDs is turned on. The calibration plot is linear in the 0.01 to 1.8 ng·mL ̄1 concentration range, with a 3 pg·mL ̄1 detection limit (at a signal-to-noise ratio of 3). The method was also applied to study the inhibition of lysozyme by IvyEc. In our perception, this method has a wide scope in that it may become applicable to any protein for which an appropriate aptamer is available.
Graphical abstract A novel convenient and universal fluorescence nanoprobe for sensitive and selective detection of lysozyme and inhibitor screening was established using triple-helix DNA mediated CuInS2 QDs and GO nanocomposites
Perovskite quantum dots (QDs) are promising as representative candidates to construct next-generation superior artificial light-harvesting systems (ALHSs). However, their high sensitivity to external environments, especially to water, imposes a stringent limitation for their actual implementation. Herein, by interface engineering and encapsulation with natural palygorskite (PAL), a water-resistant light-harvesting CsPbBr3@PAL antenna was prepared. Molecular dynamics simulations further confirm a significant shielding protection of the PAL matrix to CsPbBr3, facilitating exceptional stability of the CsPbBr3@PAL antenna when exposed to air for 10 months, to 150 °C thermal stress, and even to water for more than 30 days, respectively. Furthermore, as a result of in situ encapsulation of the PAL matrix and defect passivation caused by H-bonding and coordination-bonding interaction, the CsPbBr3@PAL antenna in water shows a substantially enhanced photoluminescence quantum yield (36.2%) and longer lifetime. After sequentially assembling Eosin Y and Rose Bengal in the pores of the PAL matrix, RB-ESY-CsPbBr3@PAL with a sequential two-step efficient Förster resonance energy transfer process exhibited extremely enhanced photocatalytic activity toward Friedel–Crafts alkylation reactions in aqueous solution, 2.5-fold higher than that of corresponding ESY/RB. Our work provides a feasible strategy for the exploitation of ultra-stable halide perovskite-based ALHSs in aqueous media for solar-energy conversion.A water-resistant light-harvesting antenna was prepared via encapsulating and in situ passivating perovskite quantum dots in PAL matrix. The ESY-RB-CsPbBr3@PAL system with high sequential FRET exhibited enhanced photocatalysis in aqueous solution. 相似文献