Full Dissolution of the Whole Lithium Sulfide Family (Li2S8 to Li2S) in a Safe Eutectic Solvent for Rechargeable Lithium–Sulfur Batteries

The lithium–sulfur battery is an attractive option for next‐generation energy storage owing to its much higher theoretical energy density than state‐of‐the‐art lithium‐ion batteries. However, the massive volume changes of the sulfur cathode and the uncontrollable deposition of Li₂S₂/Li₂S significantly deteriorate cycling life and increase voltage polarization. To address these challenges, we develop an ?‐caprolactam/acetamide based eutectic‐solvent electrolyte, which can dissolve all lithium polysulfides and lithium sulfide (Li₂S₈–Li₂S). With this new electrolyte, high specific capacity (1360 mAh g^?1) and reasonable cycling stability are achieved. Moreover, in contrast to conventional ether electrolyte with a low flash point (ca. 2 °C), such low‐cost eutectic‐solvent‐based electrolyte is difficult to ignite, and thus can dramatically enhance battery safety. This research provides a new approach to improving lithium–sulfur batteries in aspects of both safety and performance.     

An Aligned and Laminated Nanostructured Carbon Hybrid Cathode for High‐Performance Lithium–Sulfur Batteries

An aligned and laminated sulfur‐absorbed mesoporous carbon/carbon nanotube (CNT) hybrid cathode has been developed for lithium–sulfur batteries with high performance. The mesoporous carbon acts as sulfur host and suppresses the diffusion of polysulfide, while the CNT network anchors the sulfur‐absorbed mesoporous carbon particles, providing pathways for rapid electron transport, alleviating polysulfide migration and enabling a high flexibility. The resulting lithium–sulfur battery delivers a high capacity of 1226 mAh g⁻¹ and achieves a capacity retention of 75 % after 100 cycles at 0.1 C. Moreover, a high capacity of nearly 900 mAh g⁻¹ is obtained for 20 mg cm⁻², which is the highest sulfur load to the best of our knowledge. More importantly, the aligned and laminated hybrid cathode endows the battery with high flexibility and its electrochemical performances are well maintained under bending and after being folded for 500 times.     

A Freestanding Selenium Disulfide Cathode Based on Cobalt Disulfide‐Decorated Multichannel Carbon Fibers with Enhanced Lithium Storage Performance

SeS₂ shows attractive advantages beyond bare S and Se as a cathode material for lithium storage. Here, a freestanding lotus root‐like carbon fiber network decorated with CoS₂ nanoparticles (denoted as CoS₂@LRC) has been designed and prepared as the SeS₂ host for enhancing the lithium storage performance. The integrated electrode is constructed by three‐dimensional interconnected multichannel carbon fibers, which can not only accommodate high content of SeS₂ (70 wt %), but also promise excellent electron and ion transport for achieving high capacity utilization of 1015 mAh g⁻¹ at 0.2 A g⁻¹. What is more, there are numerous CoS₂ nanoparticles decorated all over the inner walls and surfaces of the carbon fibers, providing efficient sulfiphilic sites for restricting the dissolution of polysulfides and polyselenides during the electrochemical processes, thus successfully suppressing the shuttle effect and maintaining excellent cycling stability over 400 cycles at 0.5 A g⁻¹.     

Three Dimensionally Ordered Mesoporous Carbon as a Stable,High‐Performance Li–O2 Battery Cathode

Enabled by the reversible conversion between Li₂O₂ and O₂, Li–O₂ batteries promise theoretical gravimetric capacities significantly greater than Li‐ion batteries. The poor cycling performance, however, has greatly hindered the development of this technology. At the heart of the problem is the reactivity exhibited by the carbon cathode support under cell operation conditions. One strategy is to conceal the carbon surface from reactive intermediates. Herein, we show that long cyclability can be achieved on three dimensionally ordered mesoporous (3DOm) carbon by growing a thin layer of FeO_x using atomic layer deposition (ALD). 3DOm carbon distinguishes itself from other carbon materials with well‐defined pore structures, providing a unique material to gain insight into processes key to the operations of Li–O₂ batteries. When decorated with Pd nanoparticle catalysts, the new cathode exhibits a capacity greater than 6000 mAh g_carbon⁻¹ and cyclability of more than 68 cycles.     

Hollow Carbon Nanofibers Filled with MnO2 Nanosheets as Efficient Sulfur Hosts for Lithium–Sulfur Batteries

Lithium–sulfur batteries have been investigated as promising electrochemical‐energy storage systems owing to their high theoretical energy density. Sulfur‐based cathodes must not only be highly conductive to enhance the utilization of sulfur, but also effectively confine polysulfides to mitigate their dissolution. A new physical and chemical entrapment strategy is based on a highly efficient sulfur host, namely hollow carbon nanofibers (HCFs) filled with MnO₂ nanosheets. Benefiting from both the HCFs and birnessite‐type MnO₂ nanosheets, the MnO₂@HCF hybrid host not only facilitates electron and ion transfer during the redox reactions, but also efficiently prevents polysulfide dissolution. With a high sulfur content of 71 wt % in the composite and an areal sulfur mass loading of 3.5 mg cm^?2 in the electrode, the MnO₂@HCF/S electrode delivered a specific capacity of 1161 mAh g^?1 (4.1 mAh cm^?2) at 0.05 C and maintained a stable cycling performance at 0.5 C over 300 cycles.     

V2O5空心球作为高效硫载体用于锂硫电池（英文）

以V2O5空心球作为锂硫电池的正极材料,将其用于存储硫和限制多硫化物的穿梭效应。V2O5空心球的平均直径约为500 nm,为存储硫提供了更多空间并适应硫电极的体积变化。同时,V2O5对多硫化物具有很强的化学吸附性,可以有效地限制多硫化物的穿梭效应。由于中空结构增加了硫的存储,并通过化学键牢固地吸附多硫化物,使该锂硫电池同时具有高容量和良好的稳定性。V2O5/S作为正极的锂硫电池在0.1C倍率时显示出1439 mAh·g-1的高可逆容量,并在1C的倍率下循环300次后的容量约为600 mAh·g-1。     

Enhanced Adsorption of Polysulfides on Carbon Nanotubes/Boron Nitride Fibers for High-Performance Lithium-Sulfur Batteries

Lithium-sulfur (Li-S) batteries are one of the most promising high-energy-density storage systems. However, serious capacity attenuation and poor cycling stability induced by the shuttle effect of polysulfide intermediates can impede the practical application of Li-S batteries. Herein we report a novel sulfur cathode by intertwining multi-walled carbon nanotubes (CNTs) and porous boron nitride fibers (BNFs) for the subsequent loading of sulfur. This structural design enables trapping of active sulfur and serves to localize the soluble polysulfide within the cathode region, leading to low active material loss. Compared with CNTs/S, CNTs/BNFs/S cathodes deliver a high initial capacity of 1222 mAh g⁻¹ at 0.1 C. Upon increasing the current density to 4 C, the cell retained a capacity of 482 mAh g⁻¹ after 500 cycles with a capacity decay of only 0.044 % per cycle. The design of CNTs/BNFs/S gives new insight on how to optimize cathodes for Li-S batteries.     

Coaxial Carbon/MnO2 Hollow Nanofibers as Sulfur Hosts for High‐Performance Lithium‐Sulfur Batteries

Lithium‐sulfur (Li‐S) batteries have recently attracted a large amount of attention as promising candidates for next‐generation high‐power energy storage devices because of their high theoretical capacity and energy density. However, the shuttle effect of polysulfides and poor conductivity of sulfur are still vital issues that constrain their specific capacity and cyclic stability. Here, we design coaxial MnO₂‐graphitic carbon hollow nanofibers as sulfur hosts for high‐performance lithium‐sulfur batteries. The hollow C/MnO₂ coaxial nanofibers are synthesized via electrospinning and carbonization of the carbon nanofibers (CNFs), followed by an in situ redox reaction to grow MnO₂ nanosheets on the surface of CNFs. The inner graphitic carbon layer not only maintains intimate contact with sulfur and outer MnO₂ shell to significantly increase the overall electrical conductivity but also acts as a protective layer to prevent dissolution of polysulfides. The outer MnO₂ nanosheets restrain the shuttle effect greatly through chemisorption and redox reaction. Therefore, the robust S@C/MnO₂ nanofiber cathode delivers an extraordinary rate capability and excellent cycling stability with a capacity decay rate of 0.044 and 0.051 % per cycle after 1000 cycles at 1.0 C and 2.0 C, respectively. Our present work brings forward a new facile and efficient strategy for the functionalization of inorganic metal oxide on graphitic carbons as sulfur hosts for high performance Li‐S batteries.     

Ruthenium‐Oxide‐Coated Sodium Vanadium Fluorophosphate Nanowires as High‐Power Cathode Materials for Sodium‐Ion Batteries

Sodium‐ion batteries are a very promising alternative to lithium‐ion batteries because of their reliance on an abundant supply of sodium salts, environmental benignity, and low cost. However, the low rate capability and poor long‐term stability still hinder their practical application. A cathode material, formed of RuO₂‐coated Na₃V₂O₂(PO₄)₂F nanowires, has a 50 nm diameter with the space group of I4/mmm. When used as a cathode material for Na‐ion batteries, a reversible capacity of 120 mAh g^?1 at 1 C and 95 mAh g^?1 at 20 C can be achieved after 1000 charge–discharge cycles. The ultrahigh rate capability and enhanced cycling stability are comparable with high performance lithium cathodes. Combining first principles computational investigation with experimental observations, the excellent performance can be attributed to the uniform and highly conductive RuO₂ coating and the preferred growth of the (002) plane in the Na₃V₂O₂(PO₄)₂F nanowires.     

硫与Mn2O3空心球的复合结构及其在锂硫电池中的应用

在水热条件下,以碳球为模板合成了Mn₂O₃空心球,并用作锂硫电池的载硫基底材料。测试结果表明载硫量为51%的Mn₂O₃-S复合材料显示了较高的比容量,良好的循环稳定性和倍率性能。循环100圈后,最终可逆容量仍保持657 mA·g^-1,证明该Mn₂O₃空心球是一种有潜力的载硫基底材料。     

Mesoporous MnCo2O4 with a Flake‐Like Structure as Advanced Electrode Materials for Lithium‐Ion Batteries and Supercapacitors

A mesoporous flake‐like manganese‐cobalt composite oxide (MnCo₂O₄) is synthesized successfully through the hydrothermal method. The crystalline phase and morphology of the materials are characterized by X‐ray diffraction, field‐emission scanning electron microscopy, transmission electron microscopy, and Brunauer–Emmett–Teller methods. The flake‐like MnCo₂O₄ is evaluated as the anode material for lithium‐ion batteries. Owing to its mesoporous nature, it exhibits a high reversible capacity of 1066 mA h g^?1, good rate capability, and superior cycling stability. As an electrode material for supercapacitors, the flake‐like MnCo₂O₄ also demonstrates a high supercapacitance of 1487 F g^?1 at a current density of 1 A g^?1, and an exceptional cycling performance over 2000 charge/discharge cycles.     

One‐Pot Fabrication of Hierarchical Nanosheet‐Based TiO2–Carbon Hollow Microspheres for Anode Materials of High‐Rate Lithium‐Ion Batteries

Hierarchical and hollow nanostructures have recently attracted considerable attention because of their fantastic architectures and tunable property for facile lithium ion insertion and good cycling stability. In this study, a one‐pot and unusual carving protocol is demonstrated for engineering hollow structures with a porous shell. Hierarchical TiO₂ hollow spheres with nanosheet‐assembled shells (TiO₂ NHS) were synthesized by the sequestration between the titanium source and 2,2′‐bipyridine‐5,5′‐dicarboxylic acid, and kinetically controlled etching in trifluoroacetic acid medium. In addition, annealing such porous nanostructures presents the advantage of imparting carbon‐doped functional performance to its counterpart under different atmospheres. Such highly porous structures endow very large specifics surface area of 404 m² g^?1 and 336 m² g^?1 for the as‐prepared and calcination under nitrogen gas. C/TiO₂ NHS has high capacity of 204 mA h g^?1 at 1 C and a reversible capacity of 105 mA h g^?1 at a high rate of 20 C, and exhibits good cycling stability and superior rate capability as an anode material for lithium‐ion batteries.     

Über das Auftreten Höherer Selenanmonosulfandisulfonate im Verlauf der Reduktion von Selenit mit SeS3O 6 2−

Selenite reacts with SeS₃O ₆ ²⁻ in acidic solutions forming selenanmonosulfandisulfonates with up to 6 Se-atoms in the chain. Se₅S₃O ₆ ²⁻ and Se₆S₃O ₆ ²⁻ have been detected for the first time. The decomposition causes precipitation of a sulfur/selenium-mixture. For the Se-precipitation giving reactions of SeO ₃ ²⁻ with sulfite, S₂O ₃ ²⁻ , SeSO ₃ ²⁻ , SeS₂O ₆ ²⁻ and SeS₃O ₆ ²⁻ a universal reaction scheme has been developed, prevailing of the following single steps: formation of monoselenandisulfonates, formation of build-up reagents, formation of higher selenopolythionates, decomposition of the selenopolythionates with the longest chains.      

Radially Inwardly Aligned Hierarchical Porous Carbon for Ultra‐Long‐Life Lithium–Sulfur Batteries

Rational design of hollow micro‐ and/or nano‐structured cathodes as sulfur hosts has potential for high‐performance lithium‐sulfur batteries. However, their further commercial application is hindered because infusing sulfur into hollow hosts is hard to control and the interactions between high loading sulfur and electrolyte are poor. Herein, we designed hierarchical porous hollow carbon nanospheres with radially inwardly aligned supporting ribs to mitigate these problems. Such a structure could aid the sulfur infusion and maximize sulfur utilization owing to the well‐ordered pore channels. This highly organized internal carbon skeleton can also enhance the electronic conductivity. The hollow carbon nanospheres with further nitrogen‐doping as the sulfur host material exhibit good capacity and excellent cycling performance (0.044 % capacity degradation per each cycle for 1000 cycles).     

A Redox‐Active 2D Metal–Organic Framework for Efficient Lithium Storage with Extraordinary High Capacity

Metal–organic framework cathodes usually exhibit low capacity and poor electrochemical performance for Li‐ion storage owing to intrinsic low conductivity and inferior redox activity. Now a redox‐active 2D copper–benzoquinoid (Cu‐THQ) MOF has been synthesized by a simple solvothermal method. The abundant porosity and intrinsic redox character endow the 2D Cu‐THQ MOF with promising electrochemical activity. Superior performance is achieved as a Li‐ion battery cathode with a high reversible capacity (387 mA h g^?1), large specific energy density (775 Wh kg^?1), and good cycling stability. The reaction mechanism is unveiled by comprehensive spectroscopic techniques: a three‐electron redox reaction per coordination unit and one‐electron redox reaction per copper ion mechanism is demonstrated. This elucidatory understanding sheds new light on future rational design of high‐performance MOF‐based cathode materials for efficient energy storage and conversion.     

Na2FePO4F/Biocarbon Nanocomposite Hollow Microspheres Derived from Biological Cell Template as High-Performance Cathode Material for Sodium-Ion Batteries

We have successfully synthesized Na₂FePO₄F/biocarbon nanocomposite hollow microspheres from Fe^III precursor as cathodes for sodium-ion batteries through self-assembly of yeast cell biotemplate and sol-gel technology. The carbon coating on the nanoparticle surface with a mesoporous structure enhances electron diffusion into Na₂FePO₄F crystal particles. The improved electrochemical performance of Na₂FePO₄F/biocarbon nanocomposites is attributed to the larger electrode−electrolyte contact area and more active sites for Na⁺ on the surface of hollow microspheres compared with those of Na₂FePO₄F/C. The Na₂FePO₄F/biocarbon nanocomposite exhibits a high initial discharge capacity of 114.3 mAh g⁻¹ at 0.1 C, long-cycle stability with a capacity retention of 74.3 % after 500 cycles at 5 C, and excellent rate capability (70.2 mAh g⁻¹ at 5 C) compared with Na₂FePO₄F/C. This novel nanocomposite hollow microsphere structure is suitable for improving the property of other cathode materials for high-power batteries.     

Dual‐Confined Sulfur Nanoparticles Encapsulated in Hollow TiO2 Spheres Wrapped with Graphene for Lithium–Sulfur Batteries

Lithium–sulfur (Li?S) batteries are attractive owing to their higher energy density and lower cost compared with the universally used lithium‐ion batteries (LIBs), but there are some problems that stop their practical use, such as low utilization and rapid capacity‐fading of the sulfur cathode, which is mainly caused by the shuttle effect, and the uncontrollable deposition of lithium sulfide species. Herein, we report the design and fabrication of dual‐confined sulfur nanoparticles that were encapsulated inside hollow TiO₂ spheres; the encapsulated nanoparticles were prepared by a facile hydrolysis process combined with acid etching, followed by “wrapping” with graphene (G?TiO₂@S). In this unique composite architecture, the hollow TiO₂ spheres acted as effective sulfur carriers by confining the polysulfides and buffering volume changes during the charge‐discharge processes by means of physical force from the hollow spheres and chemical binding between TiO₂ and the polysulfides. Moreover, the graphene‐wrapped skin provided an effective 3D conductive network to improve the electronic conductivity of the sulfur cathode and, at the same time, to further suppress the dissolution of the polysulfides. As results, the G?TiO₂@S hybrids exhibited a high and stable discharge capacity of up to 853.4 mA h g^?1 over 200 cycles at 0.5 C (1 C=1675 mA g^?1) and an excellent rate capability of 675 mA h g^?1 at a current rate of 2 C; thus, G?TiO₂@S holds great promise as a cathode material for Li?S batteries.     

Suppressing Universal Cathode Crossover in High-Energy Lithium Metal Batteries via a Versatile Interlayer Design**

The universal cathode crossover such as chemical and oxygen has been significantly overlooked in lithium metal batteries using high-energy cathodes which leads to severe capacity degradation and raises serious safety concerns. Herein, a versatile and thin (≈25 μm) interlayer composed of multifunctional active sites was developed to simultaneously regulate the Li deposition process and suppress the cathode crossover. The as-induced dual-gradient solid-electrolyte interphase combined with abundant lithiophilic sites enable stable Li stripping/plating process even under high current density of 10 mA cm⁻². Moreover, X-ray photoelectron spectroscopy and synchrotron X-ray experiments revealed that N-rich framework and CoZn dual active sites can effectively mitigate the undesired cathode crossover, hence significantly minimizing Li corrosion. Therefore, assembled lithium metal cells using various high-energy cathode materials including LiNi_0.7Mn_0.2Co_0.1O₂, Li_1.2Co_0.1Mn_0.55Ni_0.15O₂, and sulfur demonstrate significantly improved cycling stability with high cathode loading.     

Nitrogen‐Doped Mesoporous Carbon‐Encapsulated MoO2 Nanobelts as a High‐Capacity and Stable Host for Lithium‐Ion Storage

N‐doped mesoporous carbon‐capped MoO₂ nanobelts (designated as MoO₂@NC) were synthesized and applied to lithium‐ion storage. Owing to the stable core–shell structural framework and conductive mesoporous carbon matrix, the as‐prepared MoO₂@NC shows a high specific capacity of around 700 mA h g⁻¹ at a current of 0.5 A g⁻¹, excellent cycling stability up to 100 cycles, and superior rate performance. The N‐doped mesoporous carbon can greatly improve the conductivity and provide uninhibited conducting pathways for fast charge transfer and transport. Moreover, the core–shell structure improved the structural integrity, leading to a high stability during the cycling process. All of these merits make the MoO₂@NC to be a suitable and promising material for lithium ion battery.     

Facile Synthesis of Nitrogen‐Containing Mesoporous Carbon for High‐Performance Energy Storage Applications

Porous carbon with high specific surface area (SSA), a reasonable pore size distribution, and modified surface chemistry is highly desirable for application in energy storage devices. Herein, we report the synthesis of nitrogen‐containing mesoporous carbon with high SSA (1390 m² g^?1), a suitable pore size distribution (1.5–8.1 nm), and a nitrogen content of 4.7 wt % through a facile one‐step self‐assembly process. Owing to its unique physical characteristics and nitrogen doping, this material demonstrates great promise for application in both supercapacitors and encapsulating sulfur as a superior cathode material for lithium–sulfur batteries. When deployed as a supercapacitor electrode, it exhibited a high specific capacitance of 238.4 F g^?1 at 1 A g^?1 and an excellent rate capability (180 F g^?1, 10 A g^?1). Furthermore, when an NMC/S electrode was evaluated as the cathode material for lithium–sulfur batteries, it showed a high initial discharge capacity of 1143.6 mA h g^?1 at 837.5 mA g^?1 and an extraordinary cycling stability with 70.3 % capacity retention after 100 cycles.