高序石墨电极上单分散纳米铜粒子的电结

Mechanism of copper electrocrystallization on highly oriented pyrolytic graphite electrode from a solution of 1 mmol/L CuSO4 and 1.0 mol/L H2SO4 has been studied using cyclic voltammogram and chronoamperometry. The results show that in copper electrodeposition the charge-transfer step is fast and the rate of growth is controlled by the rate of mass transfer of copper ions to the growing centers. Reduction of Cu(Ⅱ) ions did not undergo underpotential deposition. The initial deposition kinetics of Cu electrocrystallization corresponds to a model including progressive nucleation and diffusion controlled growth. Copper nanocrystals with size of 75.6 nm and relative standard deviation of 9% can be obtained by modulation potential electrodeposition.     

玻碳电极表面因瓦合金的电化学成核机理

在弱酸性因瓦合金(含镍质量分数为32~36 % 的镍铁合金)镀液中, 以线性扫描伏安法、循环伏安法和恒电位阶跃法对因瓦合金在玻碳电极表面的电沉积过程及其成核机理进行研究. 结果表明, 在该体系下, 因瓦合金在玻碳电极表面的电结晶属于扩散控制下的不可逆电极过程. 运用Scharifker-Hills理论模型(SH)拟合实验数据表明, 因瓦合金在玻碳电极表面的共沉积更加符合三维瞬时成核的成核规律. 运用Heerman-Tarallo理论模型(HT)分析得到因瓦合金在玻碳电极表面的成核生长的动力学参数, 当阶跃电位从-1.11 V变化至-1.17 V (vs SCE), 成核密度数(N₀)由0.72×10⁵ cm^-2提高至1.91×10⁵ cm^-2, 成核速率常数(A)从 40.35 s^-1增至 194.38 s^-1, 扩散系数(D)为(7.67±0.15)×10^-5 cm²•s^-1, 变化不大.     

氯离子对铜在玻碳电极上电结晶的影响

采用线性扫描伏安法和计时安培法研究了硫酸铜溶液中铜在玻碳电极上电结晶 的初期行为。在含与不含氯离子的0.05mol·L~(-1) cUso_4-0.5 mol·L~(-1) H_2SO_4电解液中,循环伏安实验结果表明铜在玻碳基体上的沉积没有经过UPD过 程;氯离子明显使Cu的沉积和氧化峰变得尖锐,促进Cu的沉积速度。计时安培实验 结果表明,Cu的电结晶按瞬时成核和三维生长方式进行。氯离子不改变Cu的结晶机 理,但在I～t曲线中,导致电流达最大(I_m)所需的时间t_m减小、晶核数密度和生 长速度增大,从而明显改变Cu沉积层的质量。当Cl~-浓度在10～20mg·L~(-1)范围 内,成核的晶核数密度达较大,即氯离子的最适宜添加量。     

BaKPbO和BaKPbBiO的熔盐阳极电结晶

钙钛石（ＡＢＯ３）型复杂氧化物由于Ａ位、Ｂ位在适当范围内掺杂其他离子而成为性能宽广的功能材料．例如ＢａＰｂＯ３及其取代物ＢａＰｂＢｉＯ是甲烷偶联反应的催化剂［１］,ＢａＰｂＢｉＯ［２］和ＢａＫＢｉＯ［３］还具有超导性．另一方面,这些复杂氧化物的功能又?..     

Nucleation of gold nanoparticles on latex particle surfaces

Gold particles were nucleated on functionalized (i.e., sulfonate or imidazole groups) latex particle surfaces. Gold ions were associated with the functional groups present on the surface of the latex particles by metal‐ligand formation and were then reduced to nucleate gold particles on the particle surface. The use of imidazole groups favored the metal‐ligand formation more effectively compared with sulfonic acid groups, so gold nucleation was investigated on the surface of imidazole‐functionalized model latex particles. The desorption of gold atoms or their surface migration first occurred during the reduction process and then gold nanoparticles were nucleated. The utilization of strong reductants, such as NaBH₄ and dimethylamine borane (DMAB) under mildly acidic conditions (i.e., pH 4) led to the deprotonation of imidazole‐rich polymer chains present on the surface of the model latex particles followed by deswelling of hydrophilic polymer surface layers. As a result, well‐dispersed gold nanoparticles were embedded in the hydrophilic polymer surface. On the other hand, the use of weak reductants led to the formation of localized gold aggregates on the surface of the latex particles. The removal of residual styrene monomer is very important because gold ions can be coordinated with the vinyl groups present in styrene monomer and would then be reduced by nucleophilic water addition. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 912–925, 2008     

Nucleation and growth of BaFxCl2-x nanorods

Different ratios and sizes of Ba2F3Cl (BaFxCl2-x, x=1.5) nanorods and nanowires and orthorhombic BaF2 (BaFxCl2-x, x=2) nanorods were prepared by using a liquid-solid-solution approach at 160 approximately 180 degrees C. The processes and results of the experiments conducted to prepare monodisperse Ba2F3Cl nanorods and nanowires showed that the specific surface area increased as the initial concentrations were multiplied. Based on this fact, a mechanism for the nucleation and growth processes of these nanocrystals that have a variety of enlarged sizes was substantiated in view of the surface chemical thermodynamics (SCT). In this SCT mechanism, the specific surface energy takes into account both the surfactant oleic acid and the nanocrystal surface, and is dominated by the chemical potential of the adsorbate.     

CO32-对羟基乙叉二膦酸体系铜电结晶的影响

采用循环伏安和计时安培法研究了羟基乙叉二膦酸(HEDPA)镀铜液中铜在玻碳电极上电结晶的初期行为。结果表明：羟基乙叉二膦酸(HEDPA)镀铜体系中,铜的电沉积过程经历了晶核形成过程;当溶液中不含CO32-时,其电结晶按连续三维成核方式进行,而CO32-的加入,使得铜电结晶按瞬时三维成核方式进行;成核数密度都随着电位的提高而增加。这可能是CO32- -以第二配体形式进入HEDPA和Cu2+构成的络合结构,从而形成更稳定的络合物吸附在电极表面所致。     

Investigation of electrochemical reactions on copper electrode in Cu4RbCl3I2 solid electrolyte

Investigations are carried out by potentiostatic method. It is found that at potentials ϕ less than 100 mV, a reaction rate of copper deposition is limited by the formation and the three-dimensional growth of copper nuclei and the rate of copper dissolution is limited by a two-dimensional growth of holes in the metal. The rate of nucleus growth was evaluated at 10⁻⁹...10⁻⁶ μm s⁻¹ depending on the potential. At ϕ>120 mV, the reaction rate is limited by charge transport at the exchange current density of 2.7 mA cm⁻² and the anodic transfer coefficient α_a≈ 0.45. The accumulation of a divalent copper phase on Cu/Cu₄RbCl₃I₂ interface at anodic polarization is explained by a parallel course of Cu⁺ − e → Cu²⁺ reaction.     

铜电极表面铜锡合金电结晶机理

在弱酸性柠檬酸盐体系铜锡合金镀液中,采用线性扫描伏安(LSV)、循环伏安(CV)和计时安培实验方法,运用Scharifker-Hills(SH)理论模型和Heerman-Tarallo(HT)理论模型分析拟合实验结果,研究铜锡合金在铜电极上的电沉积过程与电结晶机理.结果表明,铜锡合金在铜电极表面实现共沉积并遵循扩散控制下三维瞬时成核的电结晶过程.电位阶跃从-0.80 V负移至-0.85 V(vs SCE),HT理论分析得到铜锡合金的成核与生长的动力学参数分别为成核速率常数(A)值从20.19 s-1增加至177.67 s-1,成核活性位点密度数(N0)从6.10×105cm-2提高至1.42×106cm-2,扩散系数(D)为(6.13±0.62)×10-6cm2s-1.     

钯镍合金在玻碳电极上电结晶机理

在钯镍合金电解液中, 采用循环伏安和计时安培实验方法, 运用Scharifker和Hills模型、Heerman和Tarallo模型揭示钯镍合金的成核机理. 结果表明, 钯镍合金在玻碳电极上发生成核过程. Scharifker和Hills模型分析表明, 钯镍合金更符合扩散控制下的三维生长的连续成核机理. 借助于Heerman和Tarallo模型, 拟合得到钯镍合金的成核和生长的动力学参数. 拟合结果显示, 电位阶跃从-0.85 V负移至-0.92 V (vs SCE), 钯镍合金在玻碳电极上的成核速率从0.83 s^-1增加到7.71 s^-1, 成核密度数从2.77×10⁴ cm^-2提高至7.09×10⁴ cm^-2.     

Polyaniline Modified CNTs and Graphene Nanocomposite for Removal of Lead and Zinc Metal Ions: Kinetics,Thermodynamics and Desorption Studies

A novel polyaniline-modified CNT and graphene-based nanocomposite (2.32–7.34 nm) was prepared and characterized by spectroscopic methods. The specific surface area was 176 m²/g with 0.232 cm³/g as the specific pore volume. The nanocomposite was used to remove zinc and lead metal ions from water; showing a high removal capacity of 346 and 581 mg/g at pH 6.5. The data followed pseudo-second-order, intraparticle diffusion and Elovich models. Besides this, the experimental values obeyed Langmuir and Temkin isotherms. The results confirmed that the removal of lead and zinc ions occurred in a mixed mode, that is, diffusion absorption and ion exchange between the heterogeneous surface of the sorbent containing active adsorption centers and the solution containing metal ions. The enthalpy values were 149.9 and 158.6 J.mol⁻¹K⁻¹ for zinc and lead metal ions. The negative values of free energies were in the range of −4.97 to −26.3 kJ/mol. These values indicated an endothermic spontaneous removal of metal ions from water. The reported method is useful to remove the zinc and lead metal ions in any water body due to the high removal capacity of nanocomposite at natural pH of 6.5. Moreover, a low dose of 0.005 g per 30 mL made this method economical. Furthermore, a low contact time of 15 min made this method applicable to the removal of the reported metal ions from water in a short time. Briefly, the reported method is highly economical, nature-friendly and fast and can be used to remove the reported metal ions from any water resource.     

镍钨硼合金电沉积机理及镀层微晶尺寸

应用循环伏安、恒电位阶跃和X射线衍射 (XRD)等方法研究了Ni_W_B合金电沉积特点和镀层微晶尺寸 .结果表明 ,在以柠檬酸铵为络合剂的溶液中 ,Ni_W_B合金沉积层较Ni_W合金有较低的电化学活性 .电位阶跃i～t曲线分析表明 ,在玻碳电极上Ni_W_B合金电结晶过程遵循扩散控制瞬时成核三维成长模式 ,且随过电位的增加 ,电极表面晶核数增多 .XRD测试结果表明 ,随沉积电流密度提高 ,合金镀层微晶尺寸逐渐增大 ,说明电流密度提高将更加有利于Ni_W_B合金电结晶过程中的晶核生长 .     

镍钨硼合金沉积机理及镀层微晶尺寸

应用循环伏安、恒电位阶跃和Ｘ射线衍射（ＸＲＤ）等研究了Ｎｉ－Ｗ－Ｂ合金电沉积特点和镀层微晶尺寸。结果表明,在以柠檬酸铵为络合剂的溶液中,Ｎｉ－Ｗ－Ｂ合金沉积层较Ｎｉ－Ｗ合金有较低的电化学活性。电位阶跃ｉ￣ｔ曲线分析表明,在玻碳电极上Ｎｉ－Ｗ－Ｂ合金电结晶过程遵循扩散控制瞬时成核三维成长模式,且随过电位的增加,电极表面晶核数增多。ＸＲＤ测试结果表明,随沉积电流密度提高,合金镀层微晶尺寸逐渐增大,说明     

Nucleation and growth of copper on glassy carbon: Studies in extended overpotential interval

The nucleation and growth of copper crystals on a glassy carbon electrode are investigated at different constant overpotentials. Current transients are recorded and the number of copper nuclei is microscopically registered. The experimental data for the growth current are interpreted according to the theories of progressive and instantaneous nucleation and information is obtained on the stationary nucleation rate, the saturation nucleus number density and the exchange current density at the crystals–solution interface boundary.     

Heats of adsorption of hydrocarbons on solid surfaces

The integral heats of the interphase interaction of liquid aliphatic and aromatic hydrocarbons with fibers and powders of polyacrylonitrile and polypropylene, clay, and sandstone at 293 and 303 K were evaluated microcalorimetrically. The relationships between the heat of adsorption of hydrocarbons and the sorbate : adsorbent mass ratio were obtained. The heat and time needed for the interaction of hydrocarbons with the solid surfaces to reach equilibrium depend mainly on the adsorbent structure.     

Oxidized Biomass and Its Usage as Adsorbent for Removal of Heavy Metal Ions from Aqueous Solutions

Nowadays, very coarse wool fibers are considered waste biomass and are discarded at random or burned. Therefore, it is of actual interest to valorize coarse wool fibers as utile products. In this sense, we report herein an environmentally-friendly process for the preparation of a new material based on oxidized wool fibers and designed for efficient adsorption of heavy metals from wastewater. The morphology and the structure of the obtained product were characterized by scanning electron microscopy (SEM) coupled with an X-ray energy-dispersive module (EDX) and by Fourier-transform infrared spectroscopy (FTIR). Likewise, the performances of the oxidized wool fibers for the adsorption of heavy metal cations (Cu²⁺, Cd²⁺, Pb²⁺) from aqueous solutions were tested. The adsorption kinetics data were analyzed by applying the pseudo-first-order (PFO) and pseudo-second-order (PSO) kinetic models. The equilibrium of the adsorption process was investigated by using the Freundlich and Langmuir isotherm models. According to the Langmuir isotherms registered at 300 K, the maximum adsorption capacities of the oxidized wool were found to increase from Cu²⁺ (9.41 mg/g) and Cd²⁺ (10.42 mg/g) to Pb²⁺ (30.71 mg/g). Consequently, the removal efficiency of metal ions was found to vary in the range of 96.8–99.7%. The thermodynamic parameters (e.g., enthalpy, entropy, and Gibbs free energy) were calculated and discussed.     

新型储氢材料及其热力学与动力学问题

氢能作为一种理想的二次能源受到了国内外科研工作者的广泛关注,研制可以在室温和较低压力下方便、安全、高效地储存氢能的材料是氢能发展的瓶颈.到目前为止,固态储氢材料以能量密度高及安全性好等优势被认为极具应用前景,其中以轻质元素构成的氢化物(包括硼氢化物/铝氢化物(可用通式A(MH4)n表示,其中A是碱金属(Li,Na,K)或碱土金属(Be,Mg,Ca);M是硼或铝;n=1～4)、氨基氢化物(如LiNH2等))、氨硼烷(NH3BH3)、金属有机骨架材料(MOFs)是新型储氢材料研究领域的热点,本文将着重就目前这几类储氢材料的研究当中所涉及到的一些热力学及动力学问题进行总结探讨.     

Nucleation and growth of A15 V3Ga from ionimplanted supersaturated GA-V solid solutions

Homogeneous profiles of gallium were implanted into vanadium single crystals and vanadium thin films at room temperature. Channelling measurements and thin film X-ray diffraction examination revealed that the asimplanted gallium is substitutional for concentrations up to about 35 at.%. The mismatch at the coherent interface between the implanted and unimplanted region increased with increasing gallium concentration in the vanadium single crystal, and at 30 at.% Ga stress release occurred on annealing up to 700°C as a result of polygonization of the implanted single-crystal layer. Further annealing up to 800°C caused the nucleation and growth of the A15 phase. The nucleation threshold was lowest in samples with high gallium concentrations and in regions enriched with gallium. The growth rate was highest for the stoichiometric composition.     

油页岩飞灰对重金属离子的吸附动力学及热力学

采用批式振荡吸附法研究了燃油页岩电厂循环流化床锅炉飞灰对重金属离子Pb²+、Cu²+、Zn²+、Cd²+的吸附动力学及吸附热力学特性,并提出了吸附机理。结果表明,油页岩飞灰对Pb²+、Cu²+、Zn²+、Cd²+的吸附平衡数据符合Langmuir和Freundlich吸附等温方程,但Freundlich方程能够更好地描述吸附等温线。在油页岩飞灰对重金属离子吸附的初始阶段,拉格朗日准一级动力学方程、准二级动力学方程、Elovich方程、粒子内扩散模型均能很好地反映吸附模式,而整个吸附过程则遵循二级反应动力学方程,其吸附过程是液膜扩散和粒子内扩散共同作用的结果。油页岩飞灰对Pb²+、Cu²+、Zn²+、Cd²+的吸附是吸热反应。     

Detailed balance in reaction kinetics — Consequence of mass conservation?

Detailed balance condition for triangular isomerisation mechanism is derived from the more general permanence of atoms, consequently, it should be viewed as a special equilibrium result of mass conservation.