Crystallization behavior of dynamically cured polypropylene/epoxy blends

Dynamically cured polypropylene (PP)/epoxy blends compatibilized with maleic anhydride grafted PP were prepared by the curing of an epoxy resin during melt mixing with molten PP. The morphology and crystallization behavior of dynamically cured PP/epoxy blends were studied with scanning electron microscopy, differential scanning calorimetry, and polarized optical microscopy. Dynamically cured PP/epoxy blends, with the structure of epoxy particles finely dispersed in the PP matrix, were obtained, and the average diameter of the particles slightly increased with increasing epoxy resin content. In a study of the nonisothermal crystallization of PP and PP/epoxy blends, crystallization parameter analysis showed that epoxy particles could act as effective nucleating agents, accelerating the crystallization of the PP component in the PP/epoxy blends. The isothermal crystallization kinetics of PP and dynamically cured PP/epoxy blends were described by the Avrami equation. The results showed that the Avrami exponent of PP in the blends was higher than that of PP, and the crystallization rate was faster than that of PP. However, the crystallization rate decreased when the epoxy resin content was greater than 20 wt %. The crystallization thermodynamics of PP and dynamically cured PP/epoxy blends were studied according to the Hoffman theory. The chain folding energy for PP crystallization in dynamically cured PP/epoxy blends decreased with increasing epoxy resin content, and the minimum of the chain folding energy was observed at a 20 wt % epoxy resin content. The size of the PP spherulites in the blends was obviously smaller than that of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1181–1191, 2004     

Crystallization behavior of polypropylene/polycarbonate blends

Crystallization behavior and morphology of polypropylene (PP)/polycarbonate (PC) blends have been studied by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). In the study of non-isothermal crystallization of the blends, the phenomenon of multiple crystallization peaks of PP/PC blends was related to the blend morphology in which PP was the dispersed phase as small droplets in the PC matrix. The phenomenon of a single crystallization peak of the PP/PC blends was related to the blend morphology in which PP was a continuous phase; in that case the crystallization peak temperatures of the blends were higher than that of the PP. The isothermal crystallization kinetics of the PP and PP/PC (80/20) blend were described by the Avrami equation. The results showed that the Avrami exponent of the PP/PC (80/20) blend was higher than that of the PP, and the crystallization rate of the PP/PC (80/20) blend was faster than that of the PP. The crystallization rate of the PP and PP/PC (80/20) blend were calculated according to the Hoffmann theory. Both the PP and PP/PC (80/20) blend had maximum crystallization rates. The temperature at the maximum crystallization rate for the PP/PC (80/20) blend was higher than that of the PP.     

Nonisothermal crystallization behavior of isotactic polypropylene/ thermoplastic rubber blends

The morphology and crystallization behavior of blends of polypropylene (PP) and an ethylene-based thermoplastic elastomer (TPO) were investigated by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The SEM images showed a two-phase morphology for these blends. As TPO was partially crystalline, two distinct peaks were observed in both heating and cooling scans of DSC. The crystallization temperature of TPO in blends was higher than pure TPO. In contrast, the crystallization temperature of PP in blends was lower than pure PP. The crystallization behavior of blends was modeled by Avrami equation. It was observed that the presence of TPO accelerated the growth rate of crystals of PP in PP/TPO blends.     

Morphological hysteresis in immiscible PIB/PDMS blends filled with fumed silica nanoparticles

The morphological hysteresis behavior of immiscible polymer blend reflects the dependence of their steady-state morphology on the shear protocol applied. In this work, the influences of hydrophobic and hydrophilic fumed silica nanoparticles on the morphology hysteresis behavior of immiscible polyisobutylene (PIB)/polydimethylsiloxane (PDMS) (10/90) blends under simple shear flow were investigated by using optical shear technique. Compared with particle-free blend, the morphology hysteresis zone of filled blends was found to be expanded by the addition of hydrophobic or hydrophilic fumed silica nanoparticles. It was found that the expansion of the morphology hysteresis zone in hydrophobic nanoparticle-filled blend stemmed from the suppression of droplet coalescence. However, the expansion in the morphological hysteresis zone for hydrophilic nanoparticle-filled blend, which was less noticeable, might originate from the more difficult breakup of PIB droplets upon the addition of nanoparticles.     

FRACTIONATED CRYSTALLIZATION OF HDPE IN PS/POE/HDPE/SBS BLENDS

The fractionated crystallization behavior of the minor dispersed HDPE phase in PS/POE/HDPE/SBS quaternary blends was investigated by differential scanning calorimetry (DSC).Interestingly,we found that the fractionated crystallization behavior of HDPE was molecular weight dependent.At a fixed composition,HDPE with lower molecular weight showed more obvious fractionated crystallization behavior than HDPE with higher molecular weight.This was ascribed to a finer dispersion of HDPE with lower molecular weigh...     

Crystallization,melting behavior,and morphology of PP/Novolac blends

The crystallization, melting behavior, and morphology of Polypropylene (PP) and PP/Novolac blends were studied by scanning electron microscopy, wide angle X‐ray diffraction, differential scanning calorimetry, and polarized optical microscope. The results showed that the crystallization of PP in PP/Novolac blends was strongly influenced by crystallization temperature, particles size of Novolac, crosslinking, and compatibilizer maleic anhydride‐grafted PP. The Novolac resin could not only affect the crystal structure, but also acted as effective nucleating agents, accelerating the crystallization of PP in the PP/Novolac blends. And the smaller the Novolac particles were, the more effective were the nucleating agent for PP crystallization. Avrami equation was used to analyze the isothermal crystallization kinetics of PP and PP/Novolac blends. The influences of curing and compatibilizer on the crystallization behavior of PP were rather complicated. The crystallization thermodynamics were estimated using the Hoffman theory. The incorporation of cured Novolac and compatibilizer evidently decreased the chain folding energy of PP. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3288–3303, 2006     

Interplay of fractionated crystallization and morphology in polypropylene/poly(ϵ‐caprolactone) blends

The thermal behavior of melt‐mixed polypropylene (PP)/poly(?‐caprolactone) (PCL) blends was investigated with differential scanning calorimetry, and it was quantitatively related to the morphology observed through scanning electron microscopy. The PP/PCL blends were immiscible in the whole composition range; however, some interesting phenomena were found. Blends with low PP contents crystallized in a fractionated fashion. By applying a self‐nucleation procedure, we demonstrated that this occurred because of a lack of highly active heterogeneities within the confined PP domains. On the other hand, PP acted as a nucleating agent for PCL, and when the PP content was reduced, the higher surface/volume ratio increased its nucleating activity. The nucleating effect was improved when the PP was self‐nucleated because of the better nucleating effect of PP annealed crystals. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1365–1379, 2007     

Compatibilization of polypropylene/poly (ethylene oxide) blends and crystallization behavior of the blends

The compatibilization of incompatible polypropylene (PP)/poly(ethylene oxide) (PEO) blends was studied. The experimental results showed that the graft copolymer [(PP-MA)-g-PEO] of maleated PP(PP-MA) and mono-hydroxyl PEO (PEO-OH) was a good compatibilizer for the PP/PEO blends in which PP-MA also had some compatibilization. The crystallization of the blends was affected by the compatibility between PP and PEO. The interfacial behavior of the compatibilizers had an important effect on crystallization behavior of the PP/PEO blends. PEO showed fractionated crystallization in the PP/PEO blends. This behavior was studied from the view point of the theory of fractionated crystallization. © 1994 John Wiley & Sons, Inc.     

反应性单体改性PP/PS共混物结晶与熔融行为

制备了三种反应性单体和两种PP接枝物改性的PP／PS共混物,用DSC研究了改性PP／PS共混物的结晶与熔融行为。结果表明：PS的加入提高了PP的结晶温度,两种接枝物的加入进一步提高共混物中PP的结晶温度,少量反应性单体对结晶温度影响不大,但高用量时则明显提高共混物的结晶温度;外加接枝物或者反应性单体对共混物中PP的熔融温度影响不大,但是熔融峰形与结晶温度高低有关。     

SiO2纳米粒子对受限流场下聚异丁烯/聚二甲基硅氧烷共混物相形态的影响

利用显微-光学剪切联用系统构造受限剪切环境,探讨了少量不同表面性质的SiO2纳米粒子的加入对聚异丁烯(PIB)/聚二甲基硅氧烷(PDMS)不相容共混体系分散相形态演变过程的影响.研究结果表明,少量疏水性SiO2纳米粒子的加入可抑制分散相液滴的凝聚,从而抑制珍珠链状及纤维状等超级相形态的形成,使共混物表现为近似本体流体的...     

Large impact in electrical properties of polypropylene by improving the filler-matrix interface effect in PP/PS blends

Inorganic nanoparticles are widely used to improve space charge behavior, DC breakdown strength and other electrical properties of polymer insulating materials, but the uniform distribution of inorganic nanofillers in matrix is difficult due to their agglomeration and bad compatibility with the polymeric matrix. In this paper, polypropylene (PP)/polystyrene (PS) blends were prepared to suppress space charge accumulation and improve DC breakdown strength. Polypropylene-g-polystyrene (PP-g-PS) graft copolymer was used as compatibilizer to improve the compatibility of PP matrix and PS filler. The evolution of microstructure of PP/PS blends were investigated by scanning electron microscope (SEM), the space charge distributions were measured by a pulsed electro-acoustic (PEA) system, and DC breakdown strength was also tested. The morphologies show that the size of PS particles reduced to 310 nm when the content of PP-g-PS graft copolymer increased to 24 wt%, and the interaction between PP matrix and PS particles enhanced. The presence of PS particles in all PP/PS blends suppressed the space charge accumulation compared to neat PP, but the DC breakdown strength in uncompatibilized blend was lower than neat PP. The increasing of content of PP-g-PS improved the DC breakdown strength with the maximum value of 408.9 kV/mm was obtained. This may attribute to excellent interface structure formed between PP matrix and PS particles.     

The morphology of immiscible PDMS/PIB blends filled with silica nanoparticles under shear flow

The influence of surface nature (hydrophobic and hydrophilic) and concentration of silica nanoparticles on the coalescence behavior of immiscible polydimethylsiloxane (PDMS)/polyisobutylene (PIB) (90/10) blends under simple low-rate shear flow were investigated via optical shear technique. It was found that the coalescence of PIB droplets in PDMS matrix was suppressed efficiently by incorporating hydrophobic silica nanoparticles, and a constant droplet size was obtained at high particle contents. The addition of a small amount (<0.4 wt.%) of hydrophilic silica nanoparticles also decreased the size of PIB droplets. Clusters of small PIB droplets were formed at low filler concentration. When the filler concentration exceeded 0.8 wt.%, the clusters of PIB drops disappeared and elongated PIB threads with large size were formed, which suggest that the coalescence of PIB droplets was promoted. The results indicate that the discrepancy in the morphology evolution of PDMS/PIB blends upon the addition of silica nanoparticles is controlled not only by the surface chemistry of nanoparticles but also by their concentration in the blends.     

马来酸酐接枝热塑性弹性体在PP/PA6共混物中的作用

研究了马来酸酐接枝热塑性弹性体 (TPEg )作为增容剂对聚丙烯 (PP) 尼龙 6 (PA6 )共混体系的相容性、相态以及物理力学性能的影响 .研究结果表明TPEg的加入大大改善了PP PA6共混体系的相容性 ,且随TPEg含量的增大分散相粒径明显降低 ,共混物的韧性以及延展性大大提高 ,同时拉伸强度及模量仍保持较好的水平 .TPEg增容的PP PA6共混物的非等温结晶行为的研究表明 ,共混物中PP和PA6的结晶行为不同于各自纯的聚合物 ,PA6作为成核剂使PP的结晶温度提高 ;而PA6由于TPEg的加入 ,出现分级结晶现象 ,一级结晶温度略低于纯PA6的结晶温度 ,且随TPEg含量增大结晶受阻 ,二级结晶温度与PP的接近 .由于PP、PA 6以及TPEg之间存在较强的相互作用 ,三元共混物中PP及PA6的玻璃化转变温度分别较其纯聚合物升高 .基于上述结果 ,提出了本共混体系的结构模型     

iPP/HDPE/EPDM三元共混体系的组分分布、相容性和结晶行为

用DSC、~(13)C-NMR、SEM和WAXD等方法研究了IPP/HDPE/EPDM三元共混体系的组分分布、相容性和结晶行为。实验结果表明,EPDM与PE组分的相容性优于与PP组分的相容性,多数EPDM分子链段能够分布在PE组分中;EPDM含量为15％时,共混物相容性最好,SEM照片呈现晶体微区的互连或网络状结构;随EPDM含量增加,总结晶度X_c减小,其中PE组分结晶度X_(cE)有较大幅度地降低,PP组分结晶度X_(cp)基本没有变化,这可以根据EPDM和PE、PP之间相容性的差异以及PE、PP两组分在冷却过程中不同的结晶行为来解释。     

Fractionated crystallization of compatibilized LDPE/PA6 blends

The paper presents differential scanning calorimetry and electron microscopy of the fractionated crystallization and polydispersity of the dispersed PA6 phase in compatibilized LDPE/PA6 75/25 w/w blends. The compatibilizers used were (i) an acrylic acid functionalized polyethylene, Escor 5001 (EAA); (ii) an ethylene-glycidylmethacrylate copolymer, Lotader GMA AX8840 (EGMA); (iii) a polystyrene-poly(ethylene-butylene)-polystyrene triblock copolymer comprising 2 wt.% maleic anhydride grafts, Kraton FG 1901X (SEBS-g-MA). The compatibilizer SEBS-g-MA has the strongest reduction effect upon the size of PA-6 droplets. Its implementation provides the best fractionated crystallization. The fractionated crystallization has not been observed for the blend compatibilized with EGMA. The results show that the degree of compatibilization could be evaluated qualitatively by the progress of the fractionated crystallization. So, the three compatibilizers could be rated according to their effectiveness as follows: SEBS-g-MA > EAA > EGMA. The self-nucleation experiments have demonstrated that the lack of active nuclei in the finely dispersed PA6 droplets is the determining factor for the fractionated crystallization at high supercooling, and not the considered absolute particle size. The measurement of the Vickers microhardness of the compatibilized blends confirms that the compatibilizing activity of SEBS-g-MA and EAA is stronger than that of EGMA.     

Enhanced mechanics in injection molded isotactic polypropylene/polypropylene random copolymer blends via introducing network-like crystal structure

The crystallization behavior, rheological behavior, mechanical properties and microstructures of injection molded isotactic polypropylene(i PP), polypropylene random copolymer(co-PP) and i PP/co-PP blends were investigated. Differential scanning calorimetry(DSC) and dynamic rheological analysis illustrated that i PP and co-PP were compatible in the blends and co-PP uniformly dispersed in the i PP phase. Polarizing optical microscope(POM) was adopted to observe the crystal size and morphology evolution. The results of mechanical properties and scanning electron microscopy(SEM) indicated that the crystal size of i PP in i PP/co-PP blends(10 wt% co-PP + 90 wt% i PP and 30 wt% co-PP + 70 wt% i PP) radically decreased after the incorporation of co-PP. During crystallization, the molecular chain segments of co-PP could penetrate i PP spherulites and form a network-like crystalline structure. The network-like crystal structure could effectively transmit stress and consume more energy to overcome intermolecular forces to resist stretching. In this way, the strength would improve to a certain degree. The impact fracture mechanism of i PP/co-PP blends is quasi ductile fracture by multiple crazes. Our work discovered that the blends containing 10 wt% and 30 wt% of co-PP exhibited prominent toughness and reinforcement.     

Effect of blend composition and related morphology on the quasi-static fracture performance of LLDPE/PP blends

In the present work, the effect of composition and related morphology on the fracture behavior of LLDPE/PP blends was thoroughly investigated. Fracture behaviors evaluated under quasi-static loading conditions and different fracture mechanics methodologies were applied to assess fracture toughness depending on the materials behavior. For pure PP and 2575 blend, J at instability was chosen whereas for blends which exhibited completely ductile behavior (such as LLDPE, 7525 and 5050), the EWF methodology was used. Fracture mechanisms were elucidated with the aid of scanning electron microscopy, and results correlated with blends morphology. It was observed that fracture properties are mostly dominated by the majority component properties. In addition, for the 5050 blend, the presence of a co-continuous morphology is responsible for the high scatter of experimental data obtained.     

PREFERENTIAL INTERCALATION BEHAVIOR OF CLAY AND ITS EFFECT ON THE THERMAL DEGRADATION IN IMMISCIBLE PP/PS BLENDS

The typical immiscible PP/PS blend based clay nanocomposites were prepared via melt blending.The dispersion of clay was determined by X-ray diffraction (XRD) and transmission electron microscopy (TEM).Thermal stability and dynamic mechanical properties were measured by thermogravimetrical analysis (TGA) and dynamic mechanical analysis (DMA),respectively.Preferential intercalation behavior of clay in PP/PS blends was found.The dispersion of clay is significantly influenced by the polarity of PP and PS,mea...     

Selective localization of organoclay and effects on the morphology and mechanical properties of LDPE/PA11 blends with distributed and co‐continuous morphology

A study was made on the effect of small amounts of organically modified clay on the morphology and mechanical properties of blends of low‐density polyethylene and polyamide 11 at different compositions. The influence of the filler on the blend morphology was investigated using wide angle X‐ray diffractometry, scanning and transmission electron microscopy and selective extraction experiments. The filler was found to locate predominantly in the more hydrophilic polyamide phase. Although such uneven distribution does not have a significant effect on the onset of phase co‐continuity of the polymer components, it brings about a drastic refinement of the microstructure for the blends both with droplets/matrix and co‐continuous morphologies. In addition to the expected reinforcing action of the filler, the resulting fine microstructure plays an important role in enhancing the mechanical properties of the blends. This is essentially because of a good quality of stress transfer across the interface between the constituents, which also seems to benefit for a good interfacial adhesion promoted by the filler. Our results provide the experimental evidence for the capabilities of nanoparticles added to multiphase polymer systems to act selectively as a reinforcing agent for specific domains of the material and as a medium able to assist the refinement of the polymer phases during mixing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 600–609, 2010     

纳米SiO_2填充PMMA/PS复合物共连续范围的研究

采用流变法、抽提法以及扫描电镜3种表征方法研究了亲水性纳米二氧化硅粒子SiO2填充对聚甲基丙烯酸甲酯(PMMA)/聚苯乙烯(PS)不相容体系共连续范围的影响.对于未填充PMMA/PS体系,3种方法测得的共连续范围基本一致.而对于粒子填充体系,SEM与溶剂抽提法均表明随着粒子含量的增加,体系的共连续范围变宽,这是由于亲水性SiO2粒子选择性填充在极性PMMA相中,导致PMMA相的熔体粘度和弹性均有大幅提高,从而减缓了破坏共连续结构的纤维断裂或回缩等松弛过程.与SEM法和溶剂抽提法相反,流变法测得的共连续范围随粒子含量增加明显变窄,这主要是因为加入SiO2粒子后,PMMA/PS体系的弹性模量和黏度大大提高(加入7vol%的SiO2后分别增加近50倍和5倍),导致填充试样在装样和设定间距之后需要更长的松弛时间才能开始流变测试.试样在测试前长时间处于高温熔体状态时,其共连续结构很容易在界面张力的驱动下发生粗化和破碎,所以得到的共连续反而变窄.SEM和溶剂抽提法比流变法更适合用来判断粒子填充PMMA/PS体系特别是其高填充体系的共连续范围.