超高速撞击充气压力容器二次碎片减速运动建模研究

 针对空间碎片超高速撞击充气压力容器的二次碎片减速运动问题,首先根据弹丸撞击容器前壁后的破碎程度,将二次碎片分为弹丸未破碎、未完全破碎及完全破碎3种模式,分别建立了二次碎片未受气体扰动时的初始模型;然后采用理论分析手段,应用流体动力学、气-固两相流理论,对弹丸不同破碎模式下的二次碎片在容器内的运动过程进行分析,建立了二次碎片减速运动的计算模型,通过与数值模拟结果的比较,验证了计算模型的有效性。     

分布布喇格反射镜的反射特性

采用等效法布里珀罗(FP)腔方法对分布布喇格反射镜(DBR)的特性进行了研究,计算并讨论了上下两层DBR结构非对称模型反射率的变化.设计了DBR反射镜的反射谱中心波长为850nm的结构.随着DBR周期数的增加,腔反射率峰值逐渐增加.上下两层DBR反射镜的厚度由反射率和中心波长决定.实验表明,下DBR的周期数为30对左右,上DBR的周期数为20对左右,易实现激光输出.非对称的双层DBR的反射特性表明理论计算与实验结果基本一致.     

On reflection from a suddenly created plasma half-space: transientsolution

The reflection by a suddenly created plasma half-space of a time-harmonic plane electromagnetic wave propagating in free space is considered. The problem involves a temporal discontinuity, a spatial discontinuity, and a dispersive medium. The steady-state solution is obtained by considering the basic features of the scattering processes due to each of the discontinuities in terms of analogous transmission-line models. The electric field of the reflected wave consists of two components. One component (called component A) is of the same frequency as the incident wave frequency and is due to the spatial discontinuity. The other component (called component B) is of a different frequency and arises because of the temporal discontinuity. The B component is damped out even if the plasma is only slightly lossy. The damping rate of the B component is calculated. The transient solution is obtained through the use of Laplace transforms. The solution is given in terms of Bessel-like functions. The limiting value of this solution is shown to agree with the steady-state solution. Numerical results illustrating the transient effects are for two typical cases     

基于区域合并的动态阈值分割算法

在传统分块分割再合并阈值法的基础上,引入图像区域合并的思想,以邻近区域阈值相似性作为判断区域合并的依据,借助人机交互式系统,运用待识别目标灰度与完成区域合并的阈值作加权,消除区域灰度不连续,实现目标与背景的有效分离,减少算法的运算量,提高目标识别精度.实验证明,该算法实现简单且行之有效.     

氘氘中子产额铟活化诊断方法

提出了活化法测量DD中子产额的实验方法,该方法可提高DD中子产额测量的精度。方法基于铟同位素115In与DD中子的非弹性散射反应,活化反应释放的射线被HPGe探测器记录,根据活化系统标定灵敏度推算出中子产额。分析了探测器记录的活化射线数与中子产额间的关系。介绍了一套活化测量的系统设计。通过蒙特卡罗方法模拟了活化样品出射的射线数与样品厚度的关系,模拟结果表明:样品厚度取为1 cm可兼顾活化效率和测量精度。在加速器上对铟活化样品进行了标定实验,实验结果表明:在聚变中子产额大于2109的实验中可使用铟活化诊断方法,中子产额测量的相对标准误差在10%以内。随着聚变中子产额的不断提高,铟活化测量中子产额的精度可进一步提高。     

包层泵浦的铒镱共掺光纤激光高效产生的实验研究

利用尾纤输出的977nm高亮度多模半导体激光器包层泵浦铒镱共掺双包层光纤,采用非球面透镜组耦合方式,使泵浦耦合效率达66%以上,并在法布里-珀罗激光振荡腔结构中实现了高效的连续激光产生,双包层光纤长度为2m,在泵浦入纤功率为1.36W时,输出连续功率最大394mW,斜率效率达35%,激光输出波长1.565μm.     

TDI CCD像元响应不一致性校正算法

线阵TDI CCD遥感相机的不一致性校正对获取高质量的图像来说具有重要意义。主要对TDI CCD像元响应不一致性的校正算法及其硬件实现进行了深入的研究。对CCD的噪声特性进行了详细的分析,给出了像元响应不一致性(PRNU:Pixel-response non-uniformity)的退化模型及校正算法,并对其计算精度进行了分析,在硬件电路上对校正算法进行了验证,详细分析了影响校正效果的各种因素。实测结果表明,校正后图像的信噪比得到显著提高。     

Helium-3 adsorption refrigerator cooled with a closed-cycle cryocooler

A helium-3 adsorption refrigerator cooled with a pulse-tube cryocooler is developed. The refrigerator has two stages of adsorption pumping. The first stage is designed for the condensing and pumping of helium-4, whose cooling capacity is used for the condensation of helium-3. The second stage is designed for pumping helium-3. The final temperature reached by the refrigerator is 0.305 K. This temperature is retained for at least 24 h. The time required for helium recondensation and the obtainment of low temperature is 1.5 h. The cryostat is a self-contained instrument, as it contains no external gas-supply pipelines and the working gas is stored directly within the working volume of the refrigerator. The work is performed in the Frank Laboratory of Neutron Physics of the Joint Institute for Nuclear Research.     

相位光栅型波前曲率传感器

研制了一套相位光栅型波前曲率传感器。实验结果表明,相位型散焦光栅能消除零级衍射光的干扰,正负一级衍射光的衍射效率达到49%。用相差板引进波前畸变,进行了波前测量实验。用格林函数算法进行了波前恢复,并和Veeco检测结果进行了比较。制备的光栅型波前曲率传感器测量结果正确,峰谷值存在10%的误差,均方根值存在2%的误差。     

聚合硫酸铁絮凝剂中痕量镉分光光度法测定研究

本文研究了分光光度法测定聚合硫酸铁絮凝剂中痕量镉的新方法并探讨了显色反应机理。本法是利用分光光度法测定聚合硫酸铁絮凝剂中痕量镉。显色剂为罗丹明B和碘化钾。表面活性剂为聚乙烯醇(PVA)。光度显色反应灵敏度高 ,其最大吸收波长为 60 7nm。表观摩尔吸光系数为 4 99× 1 0 5L·mol- 1 ·cm- 1 。桑德尔灵敏度为 2 2 5× 1 0 - 4 μgCd(Ⅱ )·cm- 2 。镉含量在 0～ 1 5 μg·2 5mL- 1 范围内服从比尔定律。回收率为 96%～ 1 0 5 %。方法操作简便 ,不需要萃取分离 ,可在水相中直接测定 ,故大大简化了操作手续。用本法测定了聚合硫酸铁絮凝剂中的痕量镉 ,得满意效果     

1MV小型重复频率Marx发生器研制

设计了MV级小型重复频率Marx发生器,简化了发生器充放电回路,减小了能量损失;分析了隔离电感变化时对发生器输出脉冲电压波形的影响,减小了隔离电感体积,提高了隔离有效性;优化了开关腔体结构,实现了间距连续可调,且受外围结构的变化或振动影响,13个开关间隙置于同一垂线上,火花放电时产生的紫外线或射线相互照射,加速了开关导通,减小了Marx发生器输出电压抖动。塑壳电容降压使用,提高了发生器的可靠性;通过Pspice模拟和三维静电场分析,实现了发生器小型化,整个Marx发生器放置在一个密封纯净SF6气体的金属圆筒内,体积小于0.25m3。优化设计和实验研究,发生器在高阻负载上输出峰值1.02MV、前沿约30ns的高压脉冲,发生器储能290J,电压幅度抖动约10%,前沿抖动小于10ns,可实现重复频率20Hz稳定运行。     

Mo2C膜表面粗糙化规律的计算机模拟

引入晶粒边界修正,改进了Ｍｏ２Ｃ膜表面粗糙化物理模型,将ＤＴ２模型推广到包括有温度的情况对Ｍｏ２Ｃ膜表面形态进行计算机模拟并统计模拟图的高度分布,确定表面粗糙度随沉积时间和基底温度的变化规律,结果表明：引入晶粒边界修正大大促进了理论与实验结果的一致,Ｍｏ２Ｃ膜表面粗糙化属快速粗造化,粗造度随基底温度升高在而非线性地增大。     

双波段扫描辐射计的研制

介绍了一种新型小视场、高精度的双波段扫描辐射计。描述了系统的特点,分析了系统的总体方案。介绍了系统的工作原理,对系统的NETD进行了估算,对其探测器的选择、光学系统设计、调制系统设计、扫描机构设计、信号处理等方案进行了详细论述,对系统的标定和测量原理进行了分析,并给出了相应的计算公式。给出了系统的检测结果。     

飞秒紫外激光脉冲振荡的实验研究

本文讨论了采用空间光脉冲光谱的啁啾特性和选择聚焦透镜焦距相结合的技术大大提高二次谐波转换效率和产生紫外飞秒光脉冲的实验研究.采用一类相位匹配的BBO晶体,当飞秒钛宝石光脉冲平均功率为560mW时,二次谐波输出功率为352mW,二次谐波转换效率高达63%;采用一类相位匹配的LBO晶体时,获得高光束质量的倍频蓝光输出,输出平均功率为170mW,转换效率大于30%.运用LBO倍频产生的蓝光脉冲和剩余的基频光脉冲进行了三次谐波的振荡研究.三倍频晶体采用BBO,通过优化设计倍频光与基频光之间的空间模匹配及精确时间延迟,得到飞秒紫外光输出,输出功率为2mW,中心波长约为280nm,重复率为100MHz.     

A theoretical study of radiation between two concentric spheres using a modified discrete ordinates method associated with Legendre transform

A modified discrete ordinates method (DOM) is used in spherical participating media. The radiative intensity is broken up into two components. One component is traced back to the enclosure's source. It is called direct intensity. The other component is rather traced back to the contribution of the medium itself. It is called diffuse intensity. Thus, the radiative transfer equation (RTE) is transformed into two simultaneous equations: a direct RTE and a diffuse RTE. The direct RTE is solved analytically. The diffuse RTE is solved numerically using the DOM. The streaming angular derivative term appearing in spherical geometry is modeled by making use of the Finite Legendre Transform. We study a pure radiation transfer problem between two concentric spheres. The medium is assumed to be gray and isotropically scattering. The limiting spheres are considered to be opaque, gray, diffusely emitting and diffusely reflecting with uniform emissivity over each surface. The obtained results are compared with available cases reported in the literature. In particular, relative importance of the direct radiation in optically thin media is studied.     

A new similarity solution of the Burgers equation with linear damping

The direct method of Clarkson and Kruskal is used to study the symmetry reductions of the Burgers equation with linear damping. The classical similarity reductions reported previously is recovered. The new, nonclassical similarity reduction is obtained. The new similarity solution is given, and it is also obtained by means of the singular manifold method. The nonclassical method is used to demonstrate that the new exact solution is indeed a nonclassical similarity solution. This work has been supported by the Postdoctoral Science Foundation of China.     

基于干扰对消的红外焦平面非均匀性校正算法

红外焦平面器件的非均匀性产生机理复杂,难以准确拟合探测元响应曲线。提出了一种基于相关干扰抵消的非均匀性校正算法,以预先采集到的一帧黑体面源图像做为自适应干扰对消器的参考输入图像,自适应滤波器由参考输入图像迭代计算出待校正红外图像的空间噪声的最佳估计,实现从空间噪声中提取真实图像信号。自适应滤波算法采用变步长最小均方误差算法,减少了算法的运算量,提高了算法的收敛速度。理论分析以及针对实际红外图像的仿真结果表明,提出的算法校正效果好,收敛速度快,更易于工程实现。     

毛细管阵列电泳检测过程中的杂散光分析

建立了激光诱导荧光检测系统.采用光学仿真方法,建立与实际光学系统相同的模型.模拟表明:聚焦光束扫描毛细管阵列,轴上光束入射到毛细管内径中心时产生的杂散光最大,在两边逐渐减小.由毛细管产生的杂散光的平均光强是无毛细管时的2.725倍,说明由它产生的杂散光比较严重.对不同大小的内径产生的杂散光影响进行了分析比较,增大毛细管的内径,杂散光增大,但毛细管内径减小会使进样量少,检测困难,同时还会加大清洗与灌胶的难度.综合考虑,选取内径为50 μm的毛细管较为合适.利用自行设计的激光诱导荧光检测系统扫描毛细管阵列,进行了杂散光检测实验,光电倍增管记录所收集到的信号,作出了激光束扫描毛细管的不同位置时的杂散光信号强度分布图,实验与模拟结果相一致.     

Clausius-Mossotti-Type relation for planar monolayers

The dielectric properties of a quasi-two-dimensional molecular monolayer are analyzed. The dielectric function of the monolayer is expressed in terms of molecular polarizability and monolayer characteristics. The expression is analogous to the well-known Clausius-Mossotti equation for three-dimensional systems. The response of the monolayer to an external field is calculated. The case of a planar array of nanoparticles is also considered. The solution is obtained in the framework of a local-field theory.     

X波段低副瓣波导缝隙阵列天线特性

根据Stevenson等效电路法设计了两个X波段低副瓣波导缝隙阵列天线。通过建立多个缝隙时的谐振长度提取模型,计算了存在缝隙间互耦时的谐振长度。两个阵列天线测试结果和仿真结果吻合良好,线阵中心频率实测增益为17.83dB,其仿真结果为18.2dB,实测副瓣为-28.12dB,其仿真结果为-29.97dB;平面阵列中心频率实测增益为27dB,其仿真结果为27.9dB,实测H面副瓣为-27.2dB,其仿真结果为-29.9dB,实测E面副瓣为-22dB,其仿真结果为-22dB。