Alumina interaction with AMPS-MPEG random copolymers III. Effect of PEG segment length on adsorption, electrokinetic and rheological behavior

The effect of different 2-acrylamido-2-methylpropanesulfonic acid sodium salt (AMPS)-methoxypolyethyleneglycol methacrylate (MPEG) comb-like copolymers on the adsorption behavior, electrokinetic and rheological properties of alumina suspensions has been investigated. The change in adsorption isotherms with the content of the two monomers, the medium pH and the ionic strength indicated that the interaction of these copolymers was found to be controlled by both the fraction of ionic groups on the polymer and by the length of the polyethyleneglycol (PEG) segments. Adsorption of the copolymers on alumina particles is accompanied by a shift in the IEP toward acid pH values and may lead to a charge reversal above a certain level. The presence of the PEG segment equally affects the magnitude of the zeta potential by moving the shear plane forward. Addition of the copolymers greatly affects the rheological behavior of the suspension; the viscosity at a defined shear rate decreases and reaches an optimum, which is all the lower as the fraction of the ionic groups is higher. The dispersing effect of the copolymer was controlled by both the ionization level of the copolymer and by the length of the PEG segments.     

Alumina interaction with AMPS-MPEG random copolymers I. Adsorption and electrokinetic behavior

Adsorption of brush copolymers, bearing sulfonate groups and polyethylene glycol segments, on to alumina particles in suspension in water has been investigated. Study of the adsorption isotherms revealed that the copolymers displayed a strong affinity for the surface of the alumina regardless of the fraction of ionic groups on the polymer. For poly(ethylene glycol) content greater than 50%, the adsorption isotherms revealed an initial adsorption plateau followed by a second one. The shape of the adsorption isotherms was interpreted in terms of the polymer configuration at the solid-to-liquid interface. The effects of the pH and the ionic force on adsorption were studied and connected to the effects of interaction between chain segments at the surface of the alumina particles. Changes in the electrokinetic properties of the alumina particles after addition of the copolymers were investigated by following the zeta potential of particles as a function of pH. In the presence of the copolymer continuous shift of the isoelectric point IEP to a more acidic values was observed. Beyond a certain concentration the zeta potential remained negative regardless of the pH.     

RHEOLOCY OF AQUEOUS DISPERSIONS OF ALUMINA,TITANIA AND MIXTURE OF ALUMINA AND TITANIA POWDERS

The electrophoretic mobility and rheology of alumina, titania and alumina / titania powder mixtures ( ratio of alumina : titania 1 : 2 and 2 : 1 ) were investigated in aqueous suspensions in the pH range 3 - 10. The results suggest that the electrophoretic mobility of the individual powders is independent of the particle concentration, but the electrokinetic behavior of the powder mixture depends upon the concentration of the individual constituents. The rheology of all the suspensions is charge related and while alumina and alumina / titania ( ratio 2 : 1 ) flocculate at pH 9.0 both titania and alumina / titania ( ratio 1 : 2 ) form low viscous dispersions. Similarly while later dispersions flocculate at pH 5.6, the former dispersions behave as Newtonian type fluids. Better correlation between the slip rheology and the electrokinetic behavior of suspensions containing both alumina and titania powders can be obtained provided the experimental results are evaluated based upon the total surface area of the individual powders but not the particle concentration.     

Branched surface-active polylactides

A series of new branched block copolymers was synthesized and investigated, and their physicochemical and surface properties were determined. It was shown that all of the prepared block copolymers demonstrate well-defined surface activity dependent on the ratio of hydrophilic and lipophilic fragments of macromolecule as well as on the copolymer structure. The resulting copolymers were used as surfactants to obtain microemulsions and microcapsules. It was found that the size of emulsion drops stabilized by branched copolymers increased more slowly than that of drops stabilized by linear copolymers. During the preparation of microcapsules through the use of branched copolymers as surfactants, unlike that through the use of linear copolymer surfactants, a high effectiveness of encapsulation and a smaller particle size were observed.     

Physicochemical evaluation of PLA nanoparticles stabilized by water-soluble MPEO-PLA block copolymers

Different water-soluble MPEO-PLA diblock copolymers with various alpha-methoxy-omega-hydroxyl polyethylene (MPEO) and poly(lactic acid) (PLA) block lengths have been synthesized. Their surface-active properties were evidenced by surface tension (water/air) measurements. In each case the surface tension leveled down above a critical polymer concentration, which was attributed to the formation of a dense polymer layer at the liquid-air interface. The applicability of copolymers as emulsion stabilizers in the preparation of PLA nanospheres by an o/w emulsion/evaporation technique was then investigated. Four copolymers presenting sufficient water solubility and good surfactive properties were used to prepare PLA nanospheres with MPEO chains firmly anchored at the particle surface. The effect of polymer concentration in emulsion on particle size and surface coverage was examined. Whatever the copolymer characteristics, it was found that the optimal concentration to obtain a large amount of MPEO at the particle surface was similar (around 2 g/l). The effect of the copolymer composition on MPEO layer characteristics and on colloidal stability was also evaluated. The conformation of MPEO blocks at the PLA particle surface is discussed in relation to the layer thickness and the surface area occupied per molecule.     

Temperature-responsive formation of colloidal nanoparticles from poly(N-isopropylacrylamide) grafted with single-stranded DNA

The thermal properties and temperature-responsive nanoparticle formation of poly(N-isopropylacrylamide) grafted with single-stranded DNA (PNIPAAm-g-DNA) were investigated. Copolymerization between nonamer single-stranded DNA with a vinyl group at its 5' terminus (DNA macromonomer) and NIPAAm was carried out so that the DNA macromonomer unit content should be less than 1 mol %. The turbidimetry and differential scanning calorimetry of the copolymer showed that the transition temperature increased and the enthalpy change of the phase transition decreased with increasing DNA macromonomer content in the copolymers, indicating that the DNA macromonomer behaves as a hydrophilic part in the copolymer and that the hydrophilicity is greater than that of sodium styrenesulfonate. Above the phase transition temperature, the copolymers formed colloidal nanoparticles with a dehydrated PNIPAAm core surrounded by DNA. When the formation of particles was conducted at higher temperatures, the dehydration of the copolymers proceeded such that the hydrodynamic radius (Rh) of the particles decreased. From the results of light scattering measurements, we calculated the surface area of particles occupied by one DNA (S(DNA)). The S(DNA) value decreased with increasing formation temperature, indicating that the DNA density on the particle surface increases with increasing formation temperature. The increase in the DNA density was also confirmed from the zeta-potential measurement of the particle. When MgCl2 was added to the copolymer solutions, the anionic charge of DNA was neutralized by Mg2+ so that Rh and the molecular weight of the particles increased with the increasing MgCl2 concentration. The turbidimetric detection of a target DNA was successfully demonstrated by utilizing the stability decrease of the colloidal particle upon hybridization on the particle surface.     

两种[对苯乙炔-2,5-二(十二烷氧基)对苯乙炔]共聚物的合成及性能研究

用含氯前聚物路线和Ｈｅｃｋ反应分别合成［对苯乙炔－２，５－二（十二烷氧基）对苯乙炔］无规共聚物及交替共聚物．由元素分析、凝胶渗透色谱、吸收光谱及ＤＳＣ对其进行表征，研究了共聚物的组成与导电率、溶解性及发光性能的关系．比较了无规共聚物与交替共聚物在性能上的差别．     

The effect of composition drift and copolymer microstructure on mechanical bulk properties of styrene-methyl acrylate emulsion copolymers

In order to determine the influence of composition drift and copolymer microstructure on the mechanical bulk properties of styrene -methyl acrylate copolymers, several copolymers were produced by emulsion copolymerization. Three different average compositions were used. By performing the copolymerizations under batch and semicontinuous conditions with two different monomer addition strategies (starved conditions and optimal addition) it was possible to control composition drift and to produce copolymers with different microstructures (chemical composition distributions). All these copolymers were processed in a way that ensured that the original particle structure was lost before the polymers were tested. It was found that composition drift had an influence on the mechanical properties (Young's modulus, maximum stress, elongation at break). This influence could be understood very well on the basis of present knowledge about structure-mechanical properties relationships. In the case of homogeneous copolymers maximum stress and elongation at break are dependent on the molecular weight, and only weakly dependent on the chemical composition, and Young's modulus is independent of chemical composition and molecular weight in the range of compositions investigated, as expected. In the case of heterogeneous copolymers, the influence of copolymer microstructure on Young's modulus, maximum stress and elongation at break is very large. Depending on the extent of control of composition drift during the polymerizations, phase separation was observed in the processed polymers, and the presence of a rubber phase affected the properties profoundly.     

Phase separation in semicrystalline blends of poly(phenylene sulfide) and poly(ethylene terephthalate). II. Effect of poly(phenylene sulfide) homopolymer solubilization of PPS‐graft‐PET copolymer on morphology and crystallization behavior

The morphology and crystallization behavior of poly(phenylene sulfide) (PPS) and poly(ethylene terephthalate) (PET) blends compatibilized with graft copolymers were investigated. PPS‐blend‐PET compositions were prepared in which the viscosity of the PPS phase was varied to assess the morphological implications. The dispersed‐phase particle size was influenced by the combined effects of the ratio of dispersed‐phase viscosity to continuous‐phase viscosity and reduced interfacial tension due to the addition of PPS‐graft‐PET copolymers to the blends. In the absence of graft copolymer, the finest dispersion of PET in a continuous phase of PPS was achieved when the viscosity ratio between blend components was nearly equal. As expected, PET particle sizes increased as the viscosity ratio diverged from unity. When graft copolymers were added to the blends, fine dispersions of PET were achieved despite large differences in the viscosities of PPS and PET homopolymers. The interfacial activity of the PPS‐graft‐PET copolymer appeared to be related to the molecular weight ratio of the PPS homopolymer to the PPS segment of the graft copolymer (M_H/M_A). With increasing solubilization of the PPS graft copolymer segment by the PPS homopolymer, the particle size of the PET dispersed phase decreased. In crystallization studies, the presence of the PPS phase increased the crystallization temperature of PET. The magnitude of the increase in the PET crystallization temperature coincided with the viscosity ratio and extent of the PPS homopolymer solubilization in the graft copolymer. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 599–610, 2000     

Contribution of the comonomers to the bulk and surface properties of methacrylate copolymers

Relationships between formulation, bulk properties, and surface properties are investigated on series of copolymers prepared with hydroxyethylmethacrylate (HEMA), methylmethacrylate (MMA), and ethylmethacrylate (EMA) monomers, and on the homopolymers PMMA and PHEMA. The bulk water content, swelling ratio, and static (sessile drop and captive bubble) and dynamic (Wilhelmy plate technique) contact angles and the electrokinetic potential (streaming potential) are measured. The bulk water content and swelling ratio of HEMA copolymers are proportional to the amount of HEMA and are linearly correlated to the contact angle hysteresis. Periodic instabilities in the wetting cycles, similar to Haines jumps, are observed with HEMA copolymers and support a bidirectional relaxation of the hydrophilic groups respectively towards external water and capillary water. The origin of the electrokinetic potential of these nonionizable polymers is attributed to specific adsorption of [Formula: see text] ions. Its dependence on surface hydrophobicity and statistical length of the side-chains is interpreted in terms of the properties of water molecules near the interface.     

Studies on microstructure and aqueous solution properties of block copolymer of acrylamide-styrene

Three series of block copolymers of acrylamide (AM) and styrene (St) as hydrophobic comonomer with varied microstructures were prepared in microemulsion medium by changing feed ratio of monomers, ratio of St to surfactant, and amount of initiator, respectively. The effects of microstructure factors of the amphiphilic block copolymers PAM-b-PSt on their aqueous solution properties were investigated by fluorescence probe technique and surface tension measurement in detail. The experimental results show that the aqueous solution properties of PAM-b-PSt are strongly dependent on their microstructure factors, such as the length and content of PSt hydrophobic blocks in the copolymers and their molecular weight. It was found that the main microstructure factors which effect the hydrophobic association behavior of the copolymer PAM-b-PSt are the length and content of PSt hydrophobic blocks in the copolymer, whereas the hydrophobic association behavior of the copolymer is not affected nearly so much by molecular weight in more dilute regions. At the same time, it was also found that the main microstructure factors which affect the surface activity of the copolymer are the content of PSt hydrophobic blocks in the copolymer and molecular weight, whereas the length of PSt blocks in copolymer does not affect surface activity of the copolymer nearly so much under fixed content of PSt hydrophobic blocks and molecular weight in the copolymer.     

Copolymerization of Polymethyl Methacrylate Macromers with n-Butyl Acrylate and Mechanical Properties of the Graft Copolymers

The copolymerization of polymethyl methacrylate (PMMA) macromer with butyl acrylate in benzene was studied. the PMMA macromer was obtained by radical polymerization in the presence of thioglycollic acid as a chain transfer agent, followed by termination with glycidyl methacrylate. the copolymerization rate and effects of various copolymerization conditions, such as molecular weight of macromer, charging ratio of macromer to monomer, amount of initiator, kind of solvent, concentration, and copolymerization temperature, on grafting efficiency and molecular weight of copolymer were investigated. the copolymers were purified by fractional precipitation. the purified copolymers with uniform PMMA grafts were characterized by GPC, IR, UV, and DSC. Structural parameters of the copolymers were determined by VPO and membrane osmometry. Average grafting number per chain decreases with an increase of conversion. Measurement of mechanical properties of the copolymers shows that both molecular weight and the content of the macromer affect mechanical properties of the copolymer, and within a certain range they behave like a thermoplastic elastomer.     

Spontaneous formation of gold nanoparticles in poly(ethylene oxide)-poly(propylene oxide) solutions: solvent quality and polymer structure effects

We report here on the effects that the solution properties of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymers have on the reduction of hydrogen tetrachloroaurate(III) hydrate (HAuCl4.3H2O) and the size of gold nanoparticles produced. The amphiphilic block copolymer solution properties were modulated by varying the temperature and solvent quality (water, formamide, and their mixtures). We identified two main factors, (i) block copolymer conformation or structure (e.g., loops vs entanglements, nonassociated polymers vs micelles) and (ii) interactions between AuCl4- ions and block copolymers (attractive ion-dipole interactions vs repulsive interactions due to hydrophobicity), to be important for controlling the competition between the reactivities of AuCl4- reduction in the bulk solution to form gold seeds and on the surface of gold seeds (particles) and the particle size determination. The particle size increase observed with increased temperature in aqueous solutions is attributed to enhanced hydrophobicity of the block copolymer, which favors AuCl4- reduction on the surface of seeds. The lower reactivity and higher particle sizes observed in formamide solutions are attributed to the shielding of ion-dipole interaction between AuCl4- ions and block copolymers by formamide, which overcomes the beneficial effects of formamide on the block copolymer conformation (lower micelle concentration).     

Sulfonated acrylamide copolymers as pseudo-stationary phases in electrokinetic chromatography

Sulfonated copolymers were synthesized, characterized and used as separation media in electrokinetic chromatography. The polymers used were synthesized from AMPS (2-acrylamido-2-methyl-1-propanesulfonic acid) and LMAm (lauryl methacrylamide) in different mole ratios (from 100:0 to 60:40). Electrophoretic mobilities and methylene selectivities were calculated, which showed the expected correlation with the monomer ratios. The chemical selectivities for the separation of nine solutes by the copolymers were compared with that of sodium lauryl sulfate micelles, showing significant differences. No significant difference in chemical selectivities was observed for copolymers with different monomer ratios. No significant change of hydrophobic microdomain of copolymers was found in background buffers with different ionic strength values, based on the investigation of the retention factors, methylene selectivities and polymer effective mobilities. No change of hydrophobic microdomain of the copolymer solutions was found at copolymer concentrations from 0.17 to 3% (w/v), however, plots of k' versus polymer concentration suggested a different copolymer phase at lower concentrations (from 0 to 0.1%, w/v) from that at higher concentrations (from 0.17 to 3%, w/v). The copolymer with AMPS-LMAm (80:20) could be chosen as optimum copolymer as far as the methylene selectivity, peak symmetry and polymer mobility were concerned.     

Anhydrous proton-conducting properties of triazole-phosphonic acid copolymers: a combined study with MAS NMR

The synthesis, thermal and proton conducting properties of copolymers based on vinylphosphonic acid (VPA) and 1-vinyl-1,2,4-triazole (VTri) were investigated. The copolymers were synthesized by free-radical copolymerization of the corresponding monomers at several monomer feed ratios to obtain poly(VPA-co-VTri) copolymer electrolytes. The final structures of the copolymers were confirmed by spectroscopic methods. The composition of the low molecular weight copolymers was varied with the feed ratio of the monomers. The presence of triazole units in the copolymers suppresses the formation of phosphonic acid anhydrides up to 150 degrees C, as verified by both (31)P NMR and TGA. The observation of defined glass transition temperatures indicated that the ionic interactions do not prevent segmental relaxations of the polymer chains. In the absence of humidity, the copolymer electrolyte, poly(VPA-co-VTri), S2 (with 33% triazole content) showed proton conductivity of 10(-3) S cm(-1) at 120 degrees C, which is far higher than in imidazole based copolymers. Two different types of hydrogen-bonded protons were detected by (1)H MAS NMR in the solid copolymer systems, due to different arrangements of triazole and phosphonic acid units.     

醋酸乙烯酯与1-(2-叔丁基过氧异丙基)-3-异丙烯基苯(D120)的共聚行为研究

共聚合;竞聚率;过氧化物;醋酸乙烯酯与1-(2-叔丁基过氧异丙基)-3-异丙烯基苯(D120)的共聚行为研究     

Amphiphilic gradient copolymers of 2‐methyl‐ and 2‐phenyl‐2‐oxazoline: self‐organization in aqueous media and drug encapsulation

Gradient (or pseudo‐diblock) copolymers were synthesized from 2‐methyl‐2‐oxazoline and 2‐phenyl‐2‐oxazoline monomer mixtures via cationic polymerization. The self‐assembling properties of these biocompatible gradient copolymers in aqueous solutions were investigated, in an effort to use the produced nanostructures as nanocarriers for hydrophobic pharmaceutical molecules. Dynamic and static light scattering as well as AFM measurements showed that the copolymers assemble in different supramolecular nanostructures (spherical micelles, vesicles and aggregates) depending on copolymer composition. Fluorescence spectroscopy studies revealed a microenvironment of unusually high polarity inside the nanostructures. This observation is related partly to the gradient structure of the copolymers. The polymeric nanostructures were stable with time. Their structural properties in different aqueous media—PBS buffer, RPMI solution—simulating conditions used in pharmacological/medicinal studies, have been also investigated and a composition dependent behavior was observed. Finally, the hydrophobic drug indomethacin was successfully encapsulated within the gradient copolymer nanostructures and the properties of the mixed aggregates were studied in respect to the initial copolymer assemblies. The produced aggregates encapsulating indomethacin showed a significant increase of their mass and size compared to original purely polymeric ones. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

部分醇解聚乙烯醇接枝聚对二氧环己酮的合成与表征

制备了部分醇解的PVA(paPVA),将其与PDO在均相本体接枝聚合,通过对paPVA醇解度以及投料比的选择,得到了具有各种分子结构的接枝共聚物.通过一维核磁共振谱表征了聚合物的微观结构;采用TG、DSC等测试手段研究了接枝共聚物的热性能和结晶性能.     

偏氯乙烯-氯乙烯悬浮共聚物的结晶与熔融性能

研究了聚合温度、共聚物组成、低分子助剂用量等对偏氯乙烯 (VDC) 氯乙烯 (VC)悬浮共聚树脂的结晶度、熔融峰温度的影响 ,并用Florry的聚合物熔点降低理论预测共聚树脂熔点随共聚组成、低分子助剂用量的变化规律 ,为VDC VC悬浮共聚树脂的合成工艺条件和加工性能的改善提供理论基础 .     

CE and asymmetrical flow‐field flow fractionation studies of polymer interactions with surfaces and solutes reveal conformation changes of polymers

Amphiphilic diblock copolymers consisting of a hydrophobic core containing a polymerized ionic liquid and an outer shell composed of poly(N‐isoprolylacrylamide) were investigated by capillary electrophoresis and asymmetrical flow‐field flow fractionation. The polymerized ionic liquid comprised poly(2‐(1‐butylimidazolium‐3‐yl)ethyl methacrylate tetrafluoroborate) with a constant block length (n = 24), while the length of the poly(N‐isoprolylacrylamide) block varied (n = 14; 26; 59; 88). Possible adsorption of the block copolymer on the fused silica capillary, due to alterations in the polymeric conformation upon a change in the temperature (25 and 45 °C), was initially studied. For comparison, the effect of temperature on the copolymer conformation/hydrodynamic size was determined with the aid of asymmetrical flow‐field flow fractionation and light scattering. To get more information about the hydrophilic/hydrophobic properties of the synthesized block copolymers, they were used as a pseudostationary phase in electrokinetic chromatography for the separation of some model compounds, that is, benzoates and steroids. Of particular interest was to find out whether a change in the length or concentration of the poly(N‐isoprolylacrylamide) block would affect the separation of the model compounds. Overall, our results show that capillary electrophoresis and asymmetrical flow‐field flow fractionation are suitable methods for characterizing conformational changes of such diblock copolymers.