基于CuAAC反应链间自交联有机-无机杂化水性聚氨酯的合成及性能

利用4,4’-二羟甲基-1,4-庚二炔功能单体作为扩链剂合成了一系列炔基接枝量不同的水性聚氨酯（WPU）,然后基于铜催化的叠氮-炔基环加成（CuAAC）反应,采用3-叠氮基丙基三乙氧基硅烷（APTES-N₃）改性炔基功能化WPU,制备了室温链间自交联有机-无机杂化WPU. 采用红外光谱（FTIR）和核磁氢谱（¹H NMR）表征了自交联有机-无机杂化WPU. 探讨了APTES-N₃接枝量对WPU膜性能和WPU乳液形态的影响. 结果表明,随着APTES-N₃含量增加,WPU膜的结晶性逐渐下降;耐水性、耐溶剂性和热稳定性逐渐增强;WPU乳液粒子黏连程度增加. 当APTES-N₃质量分数从0增大到12%时,WPU膜的拉伸强度从14.3 MPa增加到28.6 MPa.     

High‐refractive‐index thin films prepared from aminoalkoxysilane‐capped pyromellitic dianhydride–titania hybrid materials

High‐refractive‐index aminoalkoxysilane‐capped pyromellitic dianhydride (PMDA)–titania hybrid optical thin films (TP0–TP8) were synthesized and characterized in this study. They were prepared with PMDA, aminopropyltrimethoxysilane, and titanium(IV) isopropoxide via a sol–gel process followed by spin coating and multistep baking. Through adjustments in the concentration and reaction time, the inorganic content in the hybrid thin films could be as high as 59.1 wt %. The Fourier transform infrared results indicated successful bonding between the organic and inorganic moieties. However, residues of the chelating ligands were found in the hybrids with high titania contents, affecting their thermal and optical properties. Field emission scanning electron microscopy results suggested a nanosized domain of the titania segment in the hybrid materials TP0–TP8. An atomic force microscopy study suggested that the hybrid thin films had good planarization. The dispersions of the refractive index and extinction coefficient in the wavelength range 190–900 nm were studied. The refractive indices of the prepared hybrid thin films at 633 nm increased linearly from 1.567 to 1.780 with increasing titania content. However, the Abbe numbers of the hybrid thin films showed an opposite trend. Excellent optical transparence was obtained in the visible region for the prepared hybrid thin films. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3419–3427, 2001     

New route to 3-methacryloxypropyltrimethoxysilane-base organic–inorganic hybrid film

A series of poly(3-methacryloxypropyltrimethoxysilane)/waterborne polyurethane (PMPS/WPU) composite latexes and organic–inorganic hybrid films with PMPS contents of 0, 10, 20, 30, 40 and 50 wt.% were prepared via seeded emulsion polymerization initiated by AIBN and hydrolysis–condensation process of PMPS during the evaporation of water, respectively. WPU, that is anionic polyurethane emulsion, was synthesized using isophorone diisocyanate, polytetramethylene ether glycol, dimethylol propionic acid, 1,4-butanediol, and triethylamine. An investigation of transmission electron microscopy confirmed the core–shell morphology of the composite latex particle which was composed of a PMPS core and a polyurethane shell. A dynamic light scattering analysis showed that the average particle size distributed in the range of 42–134 nm. The proposed novel preparation method included the use of polyurethane as macromolecular emulsifier and steric stabilizer, control of (3-methacryloxypropyltrimethoxysilane) (MPS) content less than 50 wt.%, slow addition of MPS and application of AIBN ensured the preparation of a stable PMPS/WPU composite latex. Formed PMPS/WPU organic–inorganic hybrid film with high PMPS content via sol-gel process had uniform transparency at visible band because of less crystalline and phase separation between organic and inorganic phases.     

Effects of alicyclic moiety incorporation on the properties of polyimide/silica hybrid films

Polyimide (PI)/silica hybrid films were prepared from tetraethyl orthosilicate (TEOS) using a sol‐gel process as well as pyromellitic dianhydride and 4,4‐oxydianiline. 1,4‐Cyclohexanedicarboxylic acid (1,4‐CHDA) was added as a coupling agent. The PI/silica hybrid films were characterized by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, differential scanning calorimetry and wide‐angle X‐ray diffraction. The thermal, tensile and dielectric properties of the hybrid films were measured. The results showed that the tensile and dielectric properties of the hybrid films improved with increasing silica concentration and 1,4‐CHDA content in the PI matrix. Covalent ester bonds were formed between SiOH groups of silica and carboxyl groups of 1,4‐CHDA. As a result, the silica particle size was reduced and dispersed homogeneously in the PI matrix, leading to increased tensile strength and tensile modulus of the typical hybrid film with 1,4‐CHDA (PI‐2), when compared with the PI/silica hybrid film without 1,4‐CHDA at the same silica contents. The presence of an alicyclic moiety containing silica in PI reduced the dielectric constant considerably to 2.83, which was lower than that of pristine PI. Copyright © 2016 John Wiley & Sons, Ltd.     

WPU预聚体中羧基含量及其位置对树脂的粒径及其耐水性之影响的研究

本文先将马来酸酐与多元醇作用，然后再与其它单体反应，合成了含有羧基的聚氨酯预聚体，并用丁酮稀释后，在普通搅拌条件下使预聚体分散于三乙醇胺的水溶液中，合成出以水为分散介质的聚氨酯分散体系（WPU）。并通过改变羧基在预聚体中的含量和位置，发现随着羧基含量的增加，WPU的粒径减小，而耐水性下降。同时发现，在一定的羧基含量下，同侧羧基相比，端羧基更有利于预聚体的乳化，制得的WPU不仅颗粒较小，而且树脂耐水性明显优于侧基羧预聚体制备的WPU，从而提出羧基的运动自由度是影响羧基乳化活性和树脂耐水性的重要因素。     

Novel inorganic morphologies formed in polyimide/silica hybrid films

2-(4-Aminophenyl)-5-aminobenzimidazole was used to prepare polyimide/silica hybrid films via sol-gel process. At 40 wt.% silica content, hybrid films were still translucent. No noticeable silica particle has been observed. Unexpectedly, after treating at 800 °C, novel morphologies of silica were observed on the surface of inorganic films, which changed from homogeneous to sea-island and to co-continuous structure with increasing silica content in the matrix. Hydrogen bonding between NH in imidazole and silanol group results that silica tends to linear structures, which is considered as the main reason for this morphological change.     

Preparation,Characterization, and Property Analysis of Environmentally Friendly Waterborne Polyurethane-Acrylate

Waterborne polyurethane (WPU) prepolymer was first prepared based on isophorone diisocyanate (IPDI), polyether polyol (NJ-210), dimethylol propionic acid (DMPA), and hydroxyethyl methyl acrylate (HEMA) via an in situ method. A series of waterborne polyurethane-acrylate (WPUA) dispersions were obtained with different proportions of acrylate (butyl acryolate and ethyl acrylate) and initiating agent by in situ dispersion technique. The structures and thermal properties of prepared WPU and WPUA were analyzed and characterized with FT-IR, UV-vis spectroscopy, and DSC. Performance of the emulsion and film was studied by means of apparent viscosity, particle size and polydispersity, surface tension, and mechanical properties. The results indicated that the particle sizes of the WPUA dispersions were larger than those of the pure WPU and the solvent resistance and mechanical properties of WPUA films were improved over those of the WPU film. The film had the greatest hardness and the least water absorption when the BA:EA mass ratio was 50:50. The obtained WPUAs have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings, and wood finishes.     

SiO2 溶胶及其静电自组装薄膜的制备

Silica sols were prepared by hydrolysis of Si（OC2H5）4（TEOS）using HCl,NH3·H2O,HCl/NH3·H2O as catalyzers,and the different granularities of SiO2 sols which catalyzed by HCl first and then NH3·H2O have the same terminal pH value were prepared. The silica colloidal particles were investigated with Transmission Electron Microscope（TEM）. The results showed sol catalyzed by HCl possesses very little particle,catalyzed by NH3·H2O has particle configuration,catalyzed by HCl/NH3·H2O possesses consecutive configuration. Poly（diallyldimethylammonium chloride）（PDDA）and SiO2 nanoparticulate complex thin films were prepared by electrostatic self-assembly multiplayer（ESAM）method. After assembling films,thin films surface conformation was observed with Electron Microscope and their transmittance was tested with 721 Spectrophotometer. The results showed that the silica sol catalyzed with HCl is not good for the fabrication of ESAM films and the silica sol catalyzed with HCl first and then NH3·H2O or by NH3·H2O only are very suitable for ESAM film fabrication. TEM data indicate that the microstructure of PDDA/ SiO2 prepared from silica sol catalyzed with HCl first and then NH3·H2O is consecutive and that the microstructure of PDDA/ SiO2 prepared from silica sol catalyzed by NH3·H2O only is particulate-parking like. The dependence of the transmittance of assembled films on the bilayer number of the films and the anti-scratching properties of the films were investigated. The results show that PDDA/ SiO2 films prepared from silica sol catalyzed by NH3·H2O only possess higher transmittance but lower anti-scratching properties. The effect of granularity of sols on optical performances of the thin films was studied,results showed the less the granularity of sol,the better the optical performances. For the sake of improving the light transmittance of films,we can reduce the granularity of sol,but it may play down its mechanical damage resist intensity.     

聚酰亚胺/二氧化硅/银杂化薄膜的制备及其结构与性能研究

采用溶胶-凝胶和原位自金属化相结合方法制备聚酰亚胺(PI)/二氧化硅(SiO2)/银(Ag)三元复合薄膜,通过红外(FTIR)、透射电镜(TEM)、动态粘弹谱仪(DMTA)等系统地考察了热处理过程中杂化薄膜结构形态变化以及SiO2含量对金属银向基体表面迁移情况和杂化薄膜各种性能的影响.实验结果表明,在热处理过程中可以同时完成聚酰胺酸的亚胺化、SiO2粒子的形成及银的还原,并且可以通过改变热处理温度和时间或改变SiO2含量来控制银粒子向聚合物基体表面的迁移.     

大分子不饱和单体法合成具有核壳结构的丙烯酸酯/聚氨酯乳液及表征

采用丙烯酸酯（AC）对水性聚氨酯（WPU）进行改性,合成了接枝型丙烯酸酯/聚氨酯(PUA)复合乳液。 随着共聚物中丙烯酸酯质量分数的增加,乳液外观由透明变为不透明,乳液粒径随之增大、分布变宽。 TEM显示,PUA乳胶粒子呈现清晰的核壳结构,且形态规整,粒径分布在60~120 nm之间。 FTIR测试表明,随着丙烯酸酯质量分数的增加,聚氨酯(PU)硬段氢键化作用先增强后减弱,硬段的有序度逐渐降低。 DSC分析表明,当AC的质量分数低于75%时,PU、聚丙烯酸酯(PA)两组分相容性较好,只出现一个玻璃化转变温度,并且随着PA质量分数的增加逐渐升高。 PA质量分数的增加,使胶膜的最大热失重速率从363 ℃提高至412 ℃,吸水率从11.3%降低至5.7%,弹性模量从16.4 MPa提高至47.6 MPa,拉伸强度从9.0 MPa提高至23.7 MPa,断裂伸长率从365%提高至408%,同时乳液的粘度下降,干燥时间变短,胶膜的附着力变好。     

水性聚氨酯硬段含量对其氢键相互作用及性能的影响

异佛尔酮二异氰酸酯（IPDI）、二羟甲基丙酸(DMPA)作为硬段,合成了水性聚氨酯。 研究了硬段含量（质量分数）对乳液稳定性、膜耐热和力学性能等的影响。 当硬段质量分数低于26%时,乳液贮存稳定性较差。 随着硬段含量增加,聚氨酯膜拉伸强度迅速增加,断裂伸长率略有降低;红外光谱显示,自由的N-H伸缩振动峰强度减弱,氢键化N-H的振动峰强度增加;同时C=O伸缩振动峰整体向低波数方向移动,C=O伸缩振动峰峰形有明显的变化;DSC测试在50～125 ℃出现明显的氢键解离现象,吸热峰增强,证实了氢键作用力随着硬段含量的增加逐渐增强。 TG测试表明,水性聚氨酯硬段和软段分步解离,随着硬段含量的增加,硬段分解温度降低,水性聚氨酯耐热性能下降。     

Organic/inorganic hybrid nano-microstructured coatings on insulated substrates by electrospray deposition

Organic/inorganic hybrid nano-microstructured coatings on insulated polymer films were prepared by electrospray deposition (ESD) from an acrylic resin/silica sol blend solution. The surface morphologies of the coated films were observed using scanning electron microscopy (SEM). The SEM images showed that a nano-microscaled fibrous structure was formed on the film. The fiber diameter decreased from 4.4 microm to 600 nm with the increase in the silica sol content. Energy-dispersive X-ray analysis also revealed that silica atoms were homogeneously distributed in the fibrous structure on the polymer film. These results indicated that the ESD method is potentially a useful option for producing nano-microstructured coatings on not only conductive, but also insulating surfaces.     

The polyurethane/polyacrylate soap-free emulsion formation: effects of hydrophilic polyurethane

The vinyl group terminated water-borne polyurethanes (WPU) with different DMPA content were prepared. Subsequently the core-shell polyurethane/polyacrylate (PUA) composite emulsions were synthesized by soap-free emulsion copolymerization. The WPU as sole surfactant was used in copolymerization, and the lowest surface tension could be achieved to 38.8?mN m^?1. Furthermore, the final conversion of acrylic monomer was reached to 98% in the case of WPU reactive seed. The FTIR-ATR indirectly confirmed the core-shell structure of PUA, simultaneously combined with DSC results found that the compatibility of WPU and PA was enhanced by growing grafting efficiency. The TEM results further indicated that the amount of DMPA in WPU had a great significant role in polymerization and final morphology structure. The PUA composite particles changed from scattered structure, core-shell structure to multi-core structure with increasing DMPA content. Correspondingly, the reinforcing and toughening effects were also found in PUA films with the increase content of DMPA by tensile testing.     

Preparation and Characterizations of New Hybrid PVA-InAlO Thin Films by Dip Coating Method

New hybrid PVA-InAlO thin films were successfully prepared by using the dip coating method. Functional group analysis confirms the presence of metal-oxide vibration in the prepared films. Structural analysis revealed that the prepared film was amorphous in nature whereas annealed films were polycrystalline in nature. Morphological images show that films are compact and have homogeneous grains of various sizes ranging between 200 and 400 nm. The compositional analysis confirms the presence of In, Al, and O. Dielectric constant values vary from 4.65 to 19.89 and dielectric loss values were ≤0.977. Activation energy was found to be very low. The results suggest that the new hybrid PVA-InAlO thin films could be used as high k layer in thin film transistor applications.     

聚氧化丙烯醚对SiO2减反膜性质的影响

采用溶胶-凝胶制备的SiO2减反膜具有优良的光学特性和高损伤阈值,可以用做高反膜和减反膜的低折射率匹配层.在高功率激光领域具有十分诱人的应用前景.     

Gelatine thin films as biomimetic surfaces for silica particles formation

The formation of silica nanostructures by several living organisms, such as diatoms or sponges, involves specific macromolecules that control the growth and the organization of silica nanoparticles. In order to investigate if a single molecular system could perform both particle size control and morphological template, gelatine thin films of various concentration and strength were prepared as biomimetic models and their reactivity towards sodium silicate aqueous solutions was studied. Simultaneous formation of silica particles in the nanometric and micrometric size range was observed. The former corresponds to colloids grown at the surface of the gelatine films and the latter to particles induced by gelatine chain brushes formed at the film/water interface. These results are in good agreement with well-known principles of biomineralization and suggest that multi-molecular systems, rather than single components, are responsible for biogenic silica nanostructure formation.     

接枝环氧树脂/硅溶胶杂化水分散液的制备与表征

利用原位分散法制备了接枝环氧树脂 硅溶胶杂化水分散液 ,并通过红外光谱和 ζ电位测定 ,表征了接枝环氧树脂与硅溶胶之间的杂化作用 .实验结果表明 ,与接枝环氧树脂水分散液相比 ,杂化水分散液的粒径和粘度均减小 .按此探讨了形成杂化水分散液的历程 .初步测定了杂化水分散液成膜后的表面性能 ,发现它们具有更高的硬度和更好的疏水性能 ,与成膜过程中硅溶胶在膜表面的富集效应有关     

Physical characteristics and properties of waterborne polyurethane materials reinforced with silk fibroin powder

Degummed silk filament was pulverized with a home‐made machine to obtain silk fibroin (SF) powder, and the structure, morphology, and particle size of the SF powder were investigated. The individual spherical particles and aggregates with different morphology of silk fibroin coexisted in water. A waterborne polyurethane (WPU) aqueous dispersion was blended with the SF powder to prepare novel blended materials with improved physical properties. The average particle size and zeta potential of the WPU/SF aqueous dispersions were characterized. The result showed that the WPU/SF dispersion with higher SF content exhibited a less negative zeta potential and a larger average particle size. Furthermore, the effect of SF content on the morphology, miscibility, and mechanical properties of the resulting blended films was studied by scanning electron microscopy, wide‐angle X‐ray diffraction, dynamic mechanical thermal analysis, and tensile testing. The films showed an improved Young's modulus and tensile strength from 0.3 to 33.8 MPa, and 0.6 to 5.2 MPa, respectively, with the increasing of SF up to a content of 26 wt %. The negative charges in the periphery and the small particle size made a good effort on dispersing SF powder into the WPU matrix as small aggregates, and the SF powder led to the efficient strengthening of WPU materials. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 940–950, 2010     

Preparation of ultrathin membranes by layer-by-layer (LBL) deposition of oppositely charged inorganic colloids

Nanofilms were prepared by alternating deposition of Mg–Al (2:1) NO ₃ ⁻ layered double hydroxide (LDH), hectorite and silica particles present study. The charge density of the oppositely charged materials strongly affect film properties like thickness and ordering. The specific charge of the colloidal particles was measured with the particle charge detector. The sequential build up of the thin films was followed by spectrophotometry and X-ray diffraction (XRD). The surface morphology of the formed multilayers was characterized and film thickness determination was performed by atomic force microscopy. The influence of the charge density of hectorite and silica particles on the LDH/hectorite, LDH/silica film thickness was studied. The results reveal that the LDH concentration has a significant effect on the film thickness while the hectorite and silica concentration were not important. Films prepared from the different types of negatively charged inorganic particles in the same concentration range (0.25–1.0%) have similar thickness because of the much higher surface charge relative to the LDH lamellae.     

Effect of Doped Boron on the Properties of ZnO Thin Films Prepared by Sol-gel Spin Coating

Transparent conductive boron-doped ZnO thin films were prepared by sol-gel spin coating method. The effect of doped boron concentration on the properties of the films was systematically discussed. The films were characterized by X-ray diffraction, atomic force microscopy, spectrophotometry, and Hall effect measurement system. All the doped and undoped ZnO films were of a single hexagonal structure, and showed a preferred orientation of （002）. The particle size and surface roughness of the films decreased with increased doped boron concentration. All the films exhibited an average transmittance of approximate 90% in visible-light region and an energy gap of about 3.3 cV. The maximum carrier concentration, the highest carrier mobility and the lowest resistivity were observed at a doped boron concentration of 0.5%（molar fraction）. Based on these results, we suggested that the saturation concentration of doped boron in ZnO film is 0.5%（molar fraction）.