不同原油中金属元素的测定及聚类分析

采用二氯甲烷溶解、分散原油样品,以浓HNO3-H2O2为消解体系,采用微波法对原油进行消解,利用电感耦合等离子体质谱法(ICP-MS)测定原油中的V、Ni、Cu、Fe、Cr、Zn、Pb、Co、Mo、Ag等17种微量金属元素;并以 6Li、45Sc、72Ge、89Y、115In、159Tb、209Bi为内标元素,补偿基体效应,选择适当的待测元素同位素克服质谱干扰,优化了实验条件.结果表明,原油中大多微量金属元素的检出限达到ng/L,仅Fe、As、Sb 3种元素的检出限相对较高;各元素线性关系良好,相关系数r不低于0.999 5;方法精密度较高,相对标准偏差(RSD)不大于5.0%,准确度较好,相对误差不高于10%.对不同原油样品以Ni/V与Fe/V值为变量进行聚类分析,结果发现,国内与国外不同地区原油样品具有明显差异性.     

微波灰化-电感耦合等离子体原子发射光谱法测定原油中的金属元素

采用微波灰化技术消化原油样品,并使用电感耦合等离子体原子发射光谱法(ICP-AES)测定其中Na、Mg、Ca、Fe、V、Ni和Cu的含量。探讨了原油样品中金属元素测定的称样量和微波灰化程序,并优化了仪器工作参数和实验条件。样品经微波灰化处理后,用盐酸溶解残渣,方法对Na、Mg、Ca、Fe、V、Ni和Cu元素的检出限分别为0.07、0.01、0.01、0.01、0.02、0.04和0.03mg/kg,回收率在84.5%～96.6%之间,相对标准偏差在2.1%～6.9%范围。方法简便、可靠,可用于原油中Na、Mg、Ca、Fe、V、Ni和Cu 7种金属元素的检测。     

原油中微量金属元素的测定及风化条件下元素的变化规律

建立了微波消解-电感耦舍等离子体质谱(ICP.MS)法同时测定原油及自然风化后原油中的V、Cr、Mn、Fe、Ni、zn、Mo、Ba等11种微量金属元素的方法.结果表明,11种微量金属元素的检出限为0.0056～0.8729μg/g,线性关系良好,相关系数r≥0.9995;相对标准偏差(RSD)<5.0%.经过30d风化...     

正交试验在原油重金属元素测定中的应用

采用微波消解技术,以ICP-AES同时测定原油中V、Ni、Mn、Pb重金属元素的含量。该方法回收率在94.73%～107.2%之间,相对标准偏差小于2.12%,适用于原油中各种重金属元素的测定。采用正交设计法安排实验,可以以少量的实验次数获得大量信息,既节省时间又节约药品。同时利用原油样品中的V/Ni的比值作为参数,可判断原油油源的特征及地质特点。     

微波消解-高分辨电感耦合等离子体质谱(HR-ICP-MS)法测定原油中22种微量元素

准确测定原油中微量元素含量,对研究原油地球化学,揭示原油原产地信息,具有重要意义。本文采用HNO3微波消解原油样品,优化了样品质量、消解试剂、消解程序等微波消解条件,研究了原油中B、Mg、Al、P、Ti、Ca、V、Cr、Mn、Fe、Co、Ni、Cu、Zn、Ga、As、Sr、Mo、Cd、Sn、Ba、Pb共22种微量元素在低、中、高分辨率下的质谱干扰及校正方法,采用高分辨测定Ca,中分辨测定P、V、Cr、Mn、Fe、Ni、Cu、Cd、Co、Sr,低分辨率模式测定其余元素,建立微波消解-高分辨电感耦合等离子体质谱测定原油22种元素的方法。在优化的实验条件下,22种元素的线性相关系数均大于0.999,方法检出限为0.0002μg/g~0.07μg/g。选择原油多元素均质标准品（ConostanS-21）进行方法验证,B、Mg、Al、P、Ti、Ca、V、Cr、Mn、Fe、Ni、Cu、Zn、Mo、Cd、Sn、Ba、Pb元素测定结果的相对标准偏差为0.20%~2.80%,测定值与标准值基本一致;选择巴西原油、安哥拉原油、喀麦隆原油、尼日利亚原油进行Co、Ga、As、Sr元素加标回收试验,加标回收率为95.3%~104.3%,测定结果的相对标准偏差为0.2%~2.3%。选取巴西原油、安哥拉原油、喀麦隆原油、尼日利亚原油进行22种元素测定,分析了不同产地原油的元素含量差异。本方法能够应用于原油中多种微量元素的同时测定,灵敏度高,选择性好,检出限低,结果准确可靠,可为原油地球化学研究提供技术支持。     

镍(Ⅱ)-PAN-吐温80分光光度法测定原油中的镍

以 1 (2 吡啶偶氮 ) 2 萘酚 (PAN) -吐温 80为显色体系测定原油中的镍。配合物的最大吸收波长为 5 6 8nm ,表观摩尔吸光系数为 5 .3× 10 4L/ (mol·cm)。镍含量在 0～ 14 μg/ (2 5mL)范围内服从朗伯 -比耳定律。以三乙醇胺和硫脲作为掩蔽剂 ,可消除原油中铁 (Ⅲ )、钴 (Ⅱ )、铜 (Ⅱ )、钒 (V)等离子的干扰。人工合成样品的平均回收率为10 2 .12 % ,测定结果的相对标准偏差为 1.83%。两种原油样品中镍含量测定结果的相对标准偏差分别为 1.37%、2 .12 % ,加标回收率分别为 97.6 7%、98.76 %。     

正丁烷在VMgO和Ni-VMgO催化剂上氧化脱氢

 采用4种方法制备了VMgO催化剂样品(w(V2O5)=30%,w(MgO)=70%),并将其用于正丁烷氧化脱氢气固相反应. 结果表明,MgO经蒸馏水回流和焙烧处理后再用NH4VO3溶液浸渍所制得的VMgO,对正丁烷氧化脱氢生成丁烯和丁二烯反应具有更好的催化性能. 这是由于用该法制备的VMgO催化剂中存在较多的Mg3V2O8物种. 通过添加Ni对VMgO催化剂进行了改性. 结果表明,适量添加Ni(n(Ni)/n(V)=0.3)有利于催化剂中Mg3V2O8的生成,而Ni以Ni3V2O8的形态存在. 由此明显改善了VMgO催化剂对正丁烷氧化脱氢生成丁烯和丁二烯反应的催化性能.     

CID-ICP-AES法同时测定煤矸石中13种微量元素

讨论了煤矸石的采样、样品分解方法,以及用全谱直读ICP-CID光谱仪测定煤矸石中As、Ba、Cd、Co、Cr、Cu、Mn、Ni、Pb、Se、Sr、V和Zn等13种微量元素的方法.除As和Ni的RSD较大外,其余11种微量元素的RSD均在5%内;除Zn的回收率为107.1%外,其余12种微量元素的回收率均在95%～105%之间;人工合成样品分析结果令人满意.     

Ni-V-O催化剂的合成、表征及其催化性能

制备了Ni3V2O8, Ni2V2O7, NiV2O6催化剂, 进行了XRD, BET, H2-TPR, XPS和电导等表征, 并测试了这三种结构催化剂对丙烷氧化脱氢制丙烯反应的催化性能, 分析了影响催化性能的因素. 实验结果表明, 当丙烷的转化率为10%时, 在p-型半导体Ni3V2O8和Ni2V2O7催化剂上丙烯的选择性为69.13%和70.21%, 而在n-型半导体NiV2O6上, 丙烯的选择性为64.41%, 表明p-型半导体Ni3V2O8和Ni2V2O7的催化性能优于n-型半导体NiV2O6的催化性能. XPS实验结果表明, 这可能与p-型半导体正钒酸镍(Ni3V2O8)和焦钒酸镍(Ni2V2O7)催化剂表面含较多O-氧物种和V4+有关.     

多功能柱净化-高效液相色谱法检测麦类中赭曲霉毒素A

本文提出了一种采用高效液相色谱/荧光检测法(HPLC/FLD)测定麦类样品中赭曲霉毒素A的方法.样品经V(乙腈):V(水)=84:16提取,多功能柱净化,C18色谱柱(4.6×250 mm,5μm)分离,V(水):V(乙腈):V(乙酸)=102:96:2作流动相,流速1.0 mL/min.结果表明,标准工作液在浓度1.0～50.0μg/L范围内,峰面积与浓度成良好的线性关系,线性相关系数＞0.9999,样品在3.0,10.0,50.0 ng/g添加水平的回收率为60%～85%,相对标准偏差为7.9%～8.8%(n=8),方法检出限为3.0 ng/g(S/N＞10).本法快速、准确、操作简单,可满足大批麦类样品的检测需要.     

Multi-element analysis of Ghanaian crude oils by instrumental neutron activation analysis

Instrumental neutron activation analysis based on thermal neutrons from the Ghana Research Reactor-1 facility was utilized to analyze 18 trace elements namely Al, As, Br, Ca, Cd, Cl, Co, Cu, Fe, K, Mg, Mn, Na, Ni, S, Si, V, and Zn in two different crude oil samples from the Saltpond and Jubilee field in the Saltpond, Central region and Cape Three Points, Western region of Ghana, respectively. The sulfur concentration for both samples were low and within globally accepted range of 0.1–0.5%wt for sweet crude oil. The results of the elemental analysis showed that the two samples are relatively low in trace element concentrations compared to crude oils of other countries. Higher Fe concentration in the Jubilee crude oil indicates younger oil. The V/Ni ratios obtained for crude oils from both locations imply a possible marine organic origin and also suggest the Saltpond crude oil is more matured than the Jubilee crude oil.     

Determination of volatile and non-volatile nickel and vanadium compounds in crude oil using electrothermal atomic absorption spectrometry after oil fractionation into saturates, aromatics, resins and asphaltenes

In recent work, it has been shown that electrothermal atomic absorption spectrometry (ET AAS) can be used to differentiate between volatile and non-volatile nickel and vanadium compounds in crude oil. In the present work, the distribution of these two groups of compounds over different fractions of crude oil was investigated. For this purpose two crude oil samples were separated in two steps: firstly, the asphaltenes were precipitated with n-heptane, and secondly, the maltenes were loaded on a silica column and eluted with solvents of increasing polarity. The four fractions of maltenes eluted from silica column were: F1, saturated and light aromatics; F2, polyaromatics; F3, resins; and F4, polar compounds. Fractions F1 and F2 were further investigated using gas chromatography, and all fractions were characterized by CHN analysis, confirming the increase of aromatics in the fractions 2, 3, 4 and asphaltenes. For the determination of Ni and V by ET AAS, oil-in-water emulsions were prepared. The speciation analysis was carried out measuring without chemical modifier (stable compounds) and with 20 μg palladium (total Ni and V) and the volatile fraction was calculated by difference. The limits of detection were 0.02 μg g⁻¹ and 0.06 μg g⁻¹, for Ni and V, respectively, based on an emulsion of 2 g of oil in 10 mL. The volatile species of Ni and V were associated with fractions F3 and F4, while only thermally stable Ni and V was precipitated in part together with the asphaltenes.     

Determination of trace elements in beach asphalts by neutron activation analysis

The feasibility of using trace multielement data obtained from neutron activation analysis to identify the source of crude oil residues was recently demonstrated. This paper presents the concentrations of Br, Co, Cr, Sb, Sc, Zn, and V/Ni, for 30 crude oil residues collected from beaches (beach asphalt), using 1 g samples. The method does not require chemical separation or post-irradiation concentration. The average standard deviation for the V/Ni ratio was ±0.39.     

Determination of 18 trace elements in petroleum and its derivatives by neutron activation with a small nuclear reactor

Non-destructive neutron activation has been used to analyze 6 different samples of crude oil and heating oil, from Western Canada and Venezuela. These samples were irradiated with thermal neutrons for 2, 30 and 240 min in the SLOWPOKE reactor and the concentrations of 18 trace and minor elements (Al, As, Br, Cl, Co, Dy, Eu, Fe, I, La, Mn, Mo, Ni, Na, S, Se, Sm and V) ranging from 0.6 ppb to 2.24% have been measured. Eleven elements (As, Br, Co, Cl, Fe, Mo, Mn, Na, Ni, S and V) were determined in the fuel oil (SRM-1634) obtained from the National Bureau of Standards and were found to be in good agreement with the values certified by NBS     

Analysis of metal ions in crude oil by reversed-phase high performance liquid chromatography using short column

In this study a rapid, simultaneous analysis of V, Ni, Fe and Cu in crude oil was achieved by high performance liquid chromatography using 10 cm length reversed-phase C18 column. Since the amount of metal ions is at a very low level, in this work, solvent extraction of metals by a ligand such as 8-hydroxyquinoline from acidic media was investigated with some modification to previous procedures. Average extraction recoveries were 99, 85, 94 and 96 for V, Ni, Fe and Cu, respectively. The proposed method was successfully applied to the crude oil which was obtained from Koshk area in southern Iran. Fast analysis of metal ion in reversed-phase short column was achieved with methanol/water (55/45, v/v) and the detection limits measured as three times the background noise were obtained. Also it was shown that if small amount of 8-hydroxyquinoline was added to the mobile phase, the peak height and the peak symmetry were improved. A typical chromatogram for the separation of the 8-hydroxyquinoline complexes of V (V), Ni (II), Fe (III) and Cu (II) in crude oil was obtained in less than 4 min.     

原油标准物质中钒、钴、镍和铅的电感耦合等离子体质谱法测定

本文报道了电感耦合等离子体质谱法测定原油标准物质中V、Co、Ni、Pb的分析方法。优化了仪器操作参数，考察了测定中的谱干扰。所建立的方法快速、灵敏、准确。对原油标准物质进行了测定，分析结果与推荐值相吻合。方法的相对标准偏差为2％～11％。     

Selective detection of volatile nickel,vanadium, and iron porphyrins in crude oils by gas chromatography-atomic emission spectroscopy

This report describes the selective detection of volatile nickel, vanadium, and iron metalloporphyrins in crude oil samples. An atomic emission detector (AED) was used for simultaneous detection of these metals using the Ni 301.2 nm, V 292.4 nm, and Fe 302.1 nm emission lines. Detection limits for these metals range from 0.05 to 5 pg/sec. The presence of volatile forms of these metals in several crude oil samples has been confirmed.     

Neutron activation analysis of major and trace elements in crude petroleum

We have determined the concentration of 25 trace elements in crude petroleum from seven Libyan oil fields by instrumental neutron activation analysis. Crude oil samples were irradiated with a thermal neutron dose rate of 10¹² and 10¹³ n·cm^–2·s^–1 in the Tajoura research reactor. The concentration of U, Br, Mg, Cu, Na, V, Cl, Al, Mn and Ca is in a range of 0.015 to 84 ppm and that of sulphur of 0.12 to 1.8%. The elements Sc, Cr, Ni, Fe, Co, Zn, Ag, Se, Sb, Ba, Cs, Yb, Hf and Hg have a concentration range of 0.009 to 8747 ppb. The coefficients of variation are within 10%. The elements V and Ni occur as both porphyrin and non-porphyrin and the ratio of these two forms varies over a wide range. The V/Ni ratios are located between 0.17 and 6.67, which are comparable to the reported values for the crude oils from other countries.