High-gain and low-noise-figure erbium-doped fiber amplifier employing dual stage quadruple pass technique

A high-gain and low-noise-figure (NF) erbium-doped fiber amplifier (EDFA) was demonstrated utilizing a new technique called the dual-stage quadruple pass (DSQP) with filters. An efficient amplification occurs at the signal wavelength of 1550 nm when it travels along the DSQP amplifier. The highest gain of 62.56 dB with a low noise figure of 3.98 dB was achieved for an input signal power of −50 dBm and pump powers of 10 and 165mW in the second and first stage amplifiers respectively.     

High gain double-pass L-band EDFA with dispersion compensation as feedback loop

We demonstrate an efficient double-pass L-band erbium-doped fiber amplifier (EDFA) incorporating chirped fiber Bragg grating (CFBG). The amplifier structure exploits the characteristics of CFBG to reflect the amplified signal back into the gain medium, filter out the recycled forward amplified spontaneous emission and block the residual 1480 nm pump power. The amplifier configuration has high gain and low noise figures as compared to double-pass EDFA using broadband mirror. The demonstrated amplifier has gain of more than 48 dB and low noise figure of less than 4 dB at low input signal power of −40 dBm.     

低噪声、高增益的L -band EDFA的实验研究

针对传统的L-band EDFA的工作效率低,提出了一种基于单根光纤光栅、泵浦分配、两段级联的EDFA的新结构,其中的光纤光栅用来反射无用的后向C-band ASE.系统地研究了泵浦比例和光纤光栅波长对增益噪声指数的影响关系.最后经实验验证,得到了低噪声、高增益的L-band的EDFA.其在输入信号光（1570 nm）功率为-30 dBm及泵浦功率为70 mW时,增益为22.26 dB,增益噪声指数为4.96 dB.     

双向掺铒光纤放大器的特性分析

讨论了双向掺铒光纤放大器的结构方案,利用考虑放大的自发辐和北员耗影响的双向掺铒光纤放大器稳态放大速率方程模型分析的增益与掺铒光纤长度、输入信号光功率、帛运光功率及抽运方式等参数之间的关系,研究了单向和双向等功率抽运下正反向噪声系数随正反向信号光输入功率的变化行为。     

Gain clamping in double-pass L-band EDFA using a broadband FBG

A highly efficient gain-clamped L-band EDFA with improved noise figure characteristic is demonstrated by simply adding a broadband C-band FBG in double-pass system. The combination of the FBG and optical circulator has created laser in the cavity for gain clamping. By adjusting the power combination of pumps 1 and 2, the clamped gain level can be controlled. The amplifier gain is clamped at 28.1 dB from −40 to −25 dBm with a gain variation of less than 0.5 dB by setting the pumps 1 and 2 at 59.5 and 50.6 mW, respectively. The gain is also flat from 1574 nm to 1604 nm with a gain variation of less than 3 dB. The corresponding noise figure varies from 5.6 to 7.6 dB, which is 0.8 to 2.6 dB less than those of unclamped amplifier.     

Investigation of the optical gain and noise figure for multi-channel amplification in EDFA under optimized pump condition

We present the results of an investigation of optical gain and noise figure for simultaneous multi-channel amplification of an erbium doped fibre amplifier (EDFA) under optimized pump condition. Different pump configurations with varying input signal levels show interesting features on gain flatness. In the experiment, population inversion along the fibre length which determines the gain-spectra and noise characteristics of the amplifier is adjusted through optimized fibre length and injected pump power in order to minimize the gain-tilt at C-band. It is observed that bi-directional pumping manifests the best combination of low noise and high gain of EDFA which are useful as in-line repeaters in WDM network. We obtain 30 ± 1.5 dB intrinsically flat small signal gain from 1538 nm to 1558 nm band of wavelength with noise figure <4 dB for 16-channel simultaneous amplification in a single stage EDFA without gain flattening filter.     

Gain-clamping techniques in two-stage double-pass L-band EDFA

Two designs of long-wavelength band erbium-doped fiber amplifier (L-band EDFA) for gain clamping in double-pass systems are demonstrated and compared. The first design is based on ring laser technique where a backward amplified spontaneous emission (ASE) from the second stage is routed into the feedback loop to create an oscillating laser for gain clamping. The gain is clamped at 18.6 d B from -40 to -80 dBm with a gain variation of less than ±0.1 dB and a noise figure of less than 6 dB. Another scheme is based on partial reflection of ASE into the EDFA, which is demonstrated using a narrowband fiber Bragg grating. This scheme achieves a good gain clamping characteristic up to -12 dBm of input signal power with a gain variation of less than ±0.3 dB from a clamped gain of 22 dB. The noise figure of a 1580 nm signal is maintained below 5 dB in this amplifier since this scheme is not based on lasing mechanism. The latter scheme is also expected to be free from the relaxation oscillation problem.     

56 dB Gain EYDFA with improved noise figure with dual-stage partial double pass configuration

An efficient erbium/ytterbium co-doped fiber amplifier (EYDFA) is demonstrated by using a dual-stage partial double pass structure with a band pass filter (BPF). The amplifier achieves the maximum small signal gain of 56 dB and the corresponding noise figure of 4.66 dB at 1536 nm with an input signal power and total pump power of ?50 dBm and 140 mW, respectively. Compared with a conventional single-stage amplifier, the maximum gain enhancement of 16.99 dB is obtained at 1544 nm with the corresponding noise figure is improved by 2 dB. The proposed amplifier structure only uses a single pump source with a partial double pass scheme to provide a high gain and dual-stage structure to provide the low noise figure.     

Enhancement of Gain in L-Band Bismuth-Based Erbium-Doped Fibre Amplifier Using an Un-pumped EDF and Midway Isolator

A hybrid L-band erbium-doped fibre amplifier (EDFA) with enhanced gain characteristic is demonstrated without a significant noise figure penalty. It uses a backward C-band amplified stimulated emission from both the ends of a bismuth-based EDFA system to pump an unpumped erbium-doped fibre (EDF) for gain enhancing. The maximum gain enhancement of 4.0dB is obtained at wavelength 1604nm with EDF length of 20m. The gain spectrum is reasonably fiat in this amplifier compared with the amplifier without an EDF. The gain varies from 27.4 dB to 30.2 dB at wavelength region 1564-1608 nm with incorporation of 20 m EDF. Noise figure also varies from 6.0 to 7.TdB at this wavelength region.     

Effect of injection of C-band ASE on L-band erbium-doped fiber amplifier

The effect of injecting conventional band (C-band) amplified spontaneous emission on the performance of long-wavelength band erbium-doped fiber amplifier (L-band EDFA) is demonstrated. It uses a circulator and broadband fiber Bragg grating (FBG) to route C-band ASE from a C-band EDFA. Injection of a small amount of ASE (attenuation of 20 dB or above) improves the small signal gain with a negligible noise figure penalty compared to that of an amplifier without the ASE injection. A maximum gain improvement of 3.5 dB is obtained at an attenuation of 20 dB. At very large amounts of ASE injection (attenuation of 0 dB), the gain of the amplifier is clamped at 15.2 dB from ?40 to ?10 dBm with a gain variation of less than 0.3 dB. The saturation power is also increased from ?8 dBm (for without ASE injection) to 2 dBm (VOA=0 dB) with a slight noise figure penalty. These results show that the ASE injection technique can be used either for gain improvement or for gain clamping in L-band EDFA.     

The L-band EDFA of high clamped gain and low noise figure implemented using fiber Bragg grating and double-pass method

The L-band erbium-doped fiber amplifier (EDFA) of low noise figure and high clamped-gain using gain-clamped and double-pass configuration is presented in this paper. A total of five different configurations of EDFAs by reflection scheme with single forward pumping schemes are examined and compared here. Among these configurations, we first find the configuration of 1480-nm pumped L-band EDFA with optimum gain and noise figure value. To further minimize the gain variation, a fiber Bragg grating (FBG) with 1615-nm center wavelength and 1-nm bandwidth is determined and added in double-pass L-band EDFA. The gain variation and maximum noise figure of EDFA while channel dropping is investigated. As the number of channel dropping from 32 to 4, the L-band type-A EDFA keep the variation of gain within 2.9 dB and the maximum noise figure below 5 dB with each channel’s input power of −23 dBm.     

Gain and noise figure improvements in double-pass S-band EDFA

Double-pass short-wavelength band erbium-doped fiber amplifier (S-band EDFA) with enhanced gain and noise figure characteristics is demonstrated. It uses a broadband fiber Bragg grating (FBG) operating in conventional-band (C-band) region to reduce the C-band amplified spontaneous emission (ASE) in the amplifier system and thus increases the population inversion in the S-band region. The small signal gain is increased by about 2.7 dB for 1500 nm signal at pump power of 103 mW, compared with that of the conventional double-pass amplifier without the FBG. The corresponding noise figure is also improved by 0.5 dB.     

Gain-clamping in two-stage L-band EDFA using an unwanted backward ase from second stage

A gain clamping technique for the long wavelength band erbium-doped fiber amplifier (L-band EDFA) is presented. It uses two circulators and a broad band fiber Bragg grating to route wasted backward C-band ASE from the second stage and launch it back into the input end of the first stage of a two-stage amplifier. The two-stage L-band EDFA has shown a small signal gain improvement of 5.7 dB compared to a single-stage amplifier with a slight noise figure degradation. By utilizing the wasted backward ASE, a L-band gain-clamped EDFA with high gain can be realized. Compared to the unclamped case, this gain-clamping technique is effective in reducing the total gain variation as small as 0.3 dB.     

WDM用增益平坦的高增益低噪声双段级联掺铒光纤放大器

给出了设计波分复用(WDM)用高增益、低噪声和宽带宽增益平坦的双段级联掺铒光纤放大器(EDFA)的一般步骤和方法.通过优化设计各种参量,研制出了一台高增益、低噪声和宽带宽增益平坦的双段级联EDFA样机,实现了从1524.8～1561.4 nm共36.6 nm带宽内±0.325 dB的平坦增益,0 dBm输入时,饱和输出功率大于15 dBm的高功率输出;噪声指数低于5 dB.     

Characteristics of low noise hybrid fiber amplifier

The characteristics of hybrid fiber amplifier (HFA) are investigated. HFA is composed of three stages: short-length EDFA pre-stage, DCF Raman amplifier, and power boosting EDFA. HFA has low noise figure, high output power, and also wide input power dynamic range. Gain control method of HFA is presented experimentally, and the transient gain excursion is suppressed to less than 0.5 dB at 3 dB channel add-drop. HFA can be used as line amplifier in optical transmission link even combined with distributed Raman amplifier due to wide input power dynamic range. The transmission performance of HFA is better than EDFA by more than 1.0 dB of Q-factor in 720 km SMF transmission.     

Dual-stage L-band erbium-doped fiber amplifier with distributed pumping from single pump laser

A dual-stage L-band erbium-doped fiber amplifier with a flat gain bandwidth over 36 nm is demonstrated using pump distribution technique. The pump power was distributed to two stages depending on the splitting ratio and the length of erbium-doped fiber that was used for this configuration. Both parameters are the key components for achieving a substantially flat gain response throughout the L-band region ranging from 1570 nm to 1605 nm. Although the input signal power was varied from ? 30 dBm to 0 dBm, gain of 17 dB with slight variations of less than 1.5 dB and a noise figure of less than 6.7 dB were achieved. All the results obtained show better performances when comparison was made with the conventional single-stage L-band optical amplifier.     

Amplification enhancement of L-band erbium-doped fiber amplifiers by reflection scheme

A reflection L-band erbium-doped fiber amplifier (EDFA), which can effectively suppress and completely exploit the backward C-band amplified spontaneous emission (ASE) with a feedback reflection loop, is presented in this paper. The mechanism of the backward ASE secondary pumping effect is experimentally investigated in detail. Our experimental results have shown that, for a given input pump power, compared to the end-pumped EDFA, the gain and output power of the reflection EDFA can be improved considerably without paying much noise penalty. When the EDFA operates with flattened gain spectra, the gain is improved by about 7 dB with an extra noise penalty of about 1.2 dB, where the saturation output power is increased by 2.5–3.2 dB and which may also be made independent of the input signal power.     

Gain-clamped two-stage L-band EDFA with a FBG laser in second stage

A gain-clamped two-stage L-band EDFA is demonstrated by simply incorporating two different FBGs on both side of EDF in the second stage. It forms a FBG laser at 1560 nm to clamp the gain in the system. The gain is clamped at about 16.5 dB with gain variation of less than 1.0 dB at dynamic range up to −10 dBm. A flat gain is obtained over 30 nm of wavelength range from 1568 to 1598 nm with a gain variation of less than 1.1 dB. At the flat region, the noise figure varies from 5.0 to 5.8 dB, which is slightly higher compared to those of unclamped amplifier. The advantage of this technique is that the FBG laser does not disturb the WDM signals in the flat gain region.     

高掺杂碲基EDFA增益噪声特性的数值模拟

采用四能级理论模型对高掺杂碲基EDFA进行了数值模拟,得出C波段和L波段EDFA的主要增益和噪声系数特性,C+L波段同时放大时,20 dB增益带宽达到85 nm.同时分析了铒离子高掺杂带来的上转换效应对放大增益和噪声性能的影响程度,C波段为4％,L波段为10％,当增大泵浦光功率时,影响程度会更小,采用两段级双向泵浦结构放大时影响仅为0.1％.     

Remotely Pumped Hybrid Amplifiers for Extended Bidirectional Passive Optical Networks

In this contribution, we optimize design parameters of hybrid optical amplifiers utilizing distributed Raman amplification in transmission fiber and gain of discrete, remotely pumped erbium-doped fiber amplifier (EDFA) for wideband, bidirectional operation in metropolitan area networks (MAN). The design is based on an application of a numerical model, which takes into account pump-to-pump and signal-to-signal interactions and generation of amplified spontaneous emission in the Raman amplifier and solves the standard rate-propagation equations in an erbium-doped fiber (EDF). We predict 12 dB gain across 72 nm of optical bandwidth with gain ripple better than 10%. The recently proposed serial topology of EDFA is considered; this enables the wideband, bidirectional operation of a hybrid amplifier with only two pump laser diodes emitting in the 1430 and 1480 nm bands.