耐辐射致色聚烯烃的研究

研究了在γ射线辐照条件下受阻胺光稳定剂 (简称HALS)、各种抗氧剂对聚丙烯 (PP)和聚乙烯 (PE)的黄度 (YI)的影响。结果表明五甲基HALS比相应的四甲基HALS更能有效地阻止聚烯烃的辐射致色。抗氧剂Irganox 10 76比Irgafos16 8或IrganoxPS 80 2更有效。当抗氧剂和HALS并用时显示出协同效应 ,10 76和PDS并用时聚丙烯的黄度比单独添加 10 76或PDS的聚丙烯的黄度都低。     

聚丙烯多相体系中β晶的研究进展

综述了近年来聚丙烯(PP)基多相体系,如PP/弹性体(橡胶)、PP/聚乙烯(PE)、PP/对苯二甲酸乙二脂(PET)、PP/聚酰胺(PA)等共混体系和PP/CaCO3、PP/滑石粉、PP/蒙脱土(MMT)以及PP与其它无机物的复合体系中聚丙烯β晶的研究进展,阐述了在这些聚丙烯基共混和复合体系中影响聚丙烯β晶生成的因素、聚丙烯β晶的生成机理以及聚丙烯β晶对多相体系结构和性能的影响,并对富含β晶的聚丙烯(PP)基多相体系的研究和应用的发展趋势进行了展望。     

Carbonaceous sorbents for high‐temperature interactive liquid chromatography of polyolefins

The elution behavior of polyethylene (PE) and the three stereoisomers of polypropylene (PP) was studied on porous graphite along with three other carbon‐based sorbents, carbon‐clad zirconia particles, activated carbon, and exfoliated graphite in a systematic way in this work. Decahydronaphthalene, 1,2,3,4‐tetrahydronaphthalene, 1,3,5‐trimethylbenzene, tetrachloroethylene, xylene and p‐xylene were used as mobile phases. While PE is adsorbed to various extents on all the tested carbonaceous sorbents from the majority of the solvents, PP is fully adsorbed only in selected cases. Testing alcohols (C7–C9) as mobile phase with Hypercarb? indicates that all stereoisomers of PP are selectively adsorbed and desorbed when a solvent gradient alcohol→1,2,4‐trichlorobenzene is used at 160°C. The retention of all stereoisomers of PP increases with the polarity of the alcohol. Linear PE is retained on Hypercarb? even from 1,2‐dichloro‐ and 1,2,4‐trichlorobenzene, when a temperature below 120°C is applied, while it is not retained from these solvents at higher temperatures. All stereoisomeric forms of PP are not adsorbed under the same conditions. Some of the tested new sorbent/solvent systems have potential to be applied in routine analysis of industrially synthesised polyolefins.     

低乙烯含量聚丙烯共聚物结晶成核剂研究

利用ＤＳＣ和偏光显微镜等手段研究了部分成核剂对聚丙烯均聚物（ＰＰ）、低乙烯含量聚丙烯共聚物及聚丙烯／聚乙烯（ＰＰ／ＰＥ）共混物结晶行为的影响，结果表明所用成核剂对ＰＰ和改性ＰＰ具有一定的普适性。聚丙烯共聚物中，由于链结构规整性变差，成核剂的作用显得特别突出，而ＰＰ／ＰＥ共混物中，由于成核剂向ＰＥ相迁移而使其对ＰＰ结晶的成核效率降低。     

Determination of low levels of an antioxidant in polyolefins by large-volume injection temperature-programmed packed capillary liquid chromatography

Sub-ambient column temperatures, promoting strong interactions between the analyte and the stationary phase material, were utilized to focus large volumes of the polyolefin antioxidant Irganox 1076 [benzenepropanoic acid, 3.5-bis(1,1-dimethylethyl)-4-hydroxy-, octadecyl ester] on the column inlet, using pure acetonitrile as sample solvent and mobile phase. Injection volumes up to 100 microl were successfully employed on a 50 cm x 320 microm I.D. capillary column packed with 5 microm Kromasil 100 ODS particles. Irganox 1076 was eluted after completed injection by temperature programming, using a temperature program from 7 to 90 degrees C, in 3 degrees C min(-1). UV detection, using a low-dispersion "U"-shaped flowcell, was performed at 280 nm. The method was applied for the determination of Irganox 1076 that was extracted from low-density polyethylene (0.6 ppm, w/w). Both Soxhlet and microwave-aided solvent extractions were performed, using chloroform and acetonitrile as solvents, respectively. The microwave-aided extraction with acetonitrile was found to give approximately the same yield as the standard Soxhlet reference method. Consequently, small volumes of acetonitrile could be used both as extraction solvent, sample solvent and mobile phase, simplifying the analysis process. The mass limit of detection of the method was found to be 3.3 ng, corresponding to a concentration limit of detection of 33 ng ml(-1), utilizing an injection volume of 100 microl. The within and between day precision of retention times displayed relative standard deviations below 1.2%.     

Mechanisms of antioxidant action: Mechanochemically bound antioxidants to polyethylene and polypropylene

It is shown that a thiolamide antioxidant, 4-mercaptoacetamido diphenylamine (MADA) can be reacted with both polypropylene and polyethylene in a mechanochemical process. The resulting bound antioxidant concentrates (MADA-B) can be used for the thermal and photostabilisation of the parent polymers. The adduct is very stable to solvent extraction and is also very effective as a high temperature antioxidant for polypropylene subjected to water leaching.The uv stabilising mechanism of MADA-B is believed to be related to the regenerative process involved in the mechanism of stabilisation by hindered nitroxyl radicals.     

HALS和抗氧剂对PE辐射致色的影响

聚乙烯;稳定剂;HALS和抗氧剂对PE辐射致色的影响     

Morphology evolution and location of ethylene–propylene copolymer in annealed polyethylene/polypropylene blends

Binary blends of linear low density polyethylene (PE) and polypropylene (PP), and ternary blends of PE, PP, and EP copolymer (EPR) were prepared in a finely mixed state. In all blends the ratio of PP to PE was 85/15. In some of the blends, the PE component was labeled with a fluorescent dye; in other blends, the EPR component was labeled. These blends were investigated by laser scanning confocal fluorescence microscopy [LCFM] as a function of annealing time as well as EPR compatibilizer content. In this way we were able to follow the evolution of sample morphology and the location of the EPR in the blends. The presence of EPR in the blends retards the growth of droplets of the dispersed PE phase. When EPR was added in amounts up to 5 wt %, it tended to cover the PE droplets in patches rather than form a true core-shell structure. In the LCFM images, the EPR/PP interface appeared sharper than the EPR/PE interface. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 979–991, 1997     

Surface roughness and hydrophilicity enhancement of polyolefin‐based membranes by three kinds of plasma methods

The introduction of antibacterial property, conductivity, wettability and antithrombogenicity into polyolefin‐based membranes has evoked much attention, which can be achieved by coating hydrophilic polymers. Therefore, it is necessary to modify the roughness and hydrophilicity of polyolefin‐based membranes to enhance the coating ability. In this paper, three kinds of plasma methods, including inductively coupled (ICP) plasma, radio frequency low pressure (RFP) plasma and atmospheric dielectric barrier discharge (DBD) plasma, were used to modify the surface of the polyethylene (PE), polypropylene (PP) and polyester‐polypropylene (PET–PP) membranes. The surface roughness of the plasma‐modified PE, PP and PET–PP films was investigated by scanning electron microscopy (SEM) and atomic force microscope (AFM). The polar functional groups of films were observed by energy dispersive spectrometer (EDX) and X‐ray photoelectron spectroscopy (XPS). Besides, the hydrophilicity of the plasma‐modified PE, PP and PET–PP films was evaluated by water contact angle measurement. It was found that the surface roughness and hydrophilicity of plasma‐modified PE, PP and PET–PP films increased with the generation of oxygen‐containing functional groups (i.e. C―O, and C?O). The PET–PP membranes were treated by RFP plasma at different processing powers and times. These results indicated that plasma is an effective way to modify films, and the treatment time and power of plasma had a certain accumulation effect on the membranes' hydrophilicity. As for the roughness and hydrophilicity, the DBD plasma modifies the PE film, which is the optimum way to get the ideal roughness and hydrophilicity. Copyright © 2015 John Wiley & Sons, Ltd.     

The discovery and progress of MgCl2‐supported TiCl4 catalysts

Polyolefins represented by polyethylene (PE) and polypropylene (PP) are indispensable materials in our daily lives. TiCl₃ catalysts, established by Ziegler and Natta in the 1950s, led to the births of the polyolefin industries. However, the activities and stereospecificities of the TiCl₃ catalysts were so low that steps for removing catalyst residues and low stereoregular PP were needed in the production of PE and PP. Our discovery of MgCl₂‐supported TiCl₄ catalysts led to more than 100 times higher activities and extremely high stereospecificities, which enabled us to dispense with the steps for the removals, meaning the process innovation. Furthermore, they narrowed the molecular weight and composition distributions of PE and PP, enabling us to control the polymer structures precisely and create such new products as very low density PE or heat‐sealable film at low temperature. The typical example of the product innovations by the combination of the high stereospecificity and the narrowed composition distribution is high‐performance impact copolymer used for an automobile bumper that used to be made of metal. These process and product innovations established these polyolefin industries. The latest MgCl₂‐supported TiCl₄ catalyst is very close to perfect control of isotactic PP structure and is expected to bring about further innovations. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1–8, 2004     

Novel synthesis of nano‐calcium carbonate (CaCO3)/polystyrene (PS) core–shell nanoparticles by atomized microemulsion technique and its effect on properties of polypropylene (PP) composites

Calcium carbonate (CaCO₃)/polystyrene (PS) nanoparticles (<100 nm) with core–shell structure were synthesized by atomized microemulsion technique. The polymer chains were anchored onto the surface of nano‐CaCO₃ through triethoxyvinyl silane (TEVS) as a coupling agent. Ammonium persulfate (APS), sodium dodecyl sulfate (SDS) and n‐pentanol were used as initiator, surfactant, and cosurfactant, respectively. Polymerization mechanism of core–shell latex particles was discussed. Encapsulation of nano‐CaCO₃ by PS was confirmed by using transmission electron microscope (TEM). Grafting percentage of core–shell particles was investigated by Thermogravimetric Analyzer (TGA). Nano‐CaCO₃/PS core–shell particles were characterized by Fourier transform infrared (FTIR) spectrophotometer and differential scanning calorimeter (DSC). The results of FTIR revealed existence of a strong interaction at the interface of nano‐CaCO₃ particle and PS, which implies that the polymer chains were successfully grafted onto the surface of nano‐CaCO₃ particle through the link of the coupling agent. In addition, TGA and DSC results indicated an enhancement of thermal stability of core–shell materials compared with the pure nano‐PS. Nano‐CaCO₃/PS particles were blended with polypropylene (PP) matrix on Brabender Plastograph by melt process with different wt% of loading (i.e. 0.1–1 wt%). The interfacial adhesion between nano‐CaCO₃ particles and PP matrix was significantly improved when the nano‐CaCO3 particles were grafted with PS, which led to increased thermal, rheological, and mechanical properties of (nano‐CaCO₃/PS)/PP composites. Scanning electron microscope (SEM) and atomic force microscope (AFM) images showed a perfect dispersion of the nano‐CaCO₃ particles in PP matrix. Copyright © 2011 John Wiley & Sons, Ltd.     

Extraction and quantification of antioxidants from low-density polyethylene by microwave energy and liquid chromatography

In this paper a experimental design is applied to optimize the quantification of hindered phenol Irganox 1076, phosphite antioxidant Irgafos 168 and their oxidized product tri[2,4-di-tert-butylphenyl]phosphate from low-density polyethylene (LDPE). The developed analytical method consists of two steps: microwave-assisted extraction and reversed-phase liquid chromatography (LC) coupled with ultraviolet diode-array detector. A Plackett-Burman design was carried out in order to find the significant experimental parameters affecting the antioxidants extraction by microwave energy. These parameters were subsequently optimized by a central composite design. The performed method allows extracting the studied antioxidants at low temperature in a short time without degradation of phosphite antioxidant Irgafos 168.     

Carbon dioxide evolution and carbonyl group development during photodegradation of polyethylene and polypropylene

In situ infrared (FTIR) spectrometry has demonstrated that more CO₂ is photogenerated from polypropylene (PP) than from polyethylene (PE) films. Potential applications of the method include investigation of polymer degradation mechanism and ranking of polymer photo-stabilities in as little as 3 h.This study focuses on clarifying the mechanism of this rapid CO₂ formation from PE and PP, and complementary insight was obtained from changes in the IR transmission spectra of films irradiated by UVA for hundreds of hours. A 30 min induction time observed for CO₂ photogeneration from PP, but not PE, was reflected, on a much longer time scale, in the induction time for carbonyl development in PP, but not PE. This suggests that, in PP, the CO₂ induction time is a consequence of the slow development of carbonyl groups, a hypothesis that is supported by the elimination of the PP induction time when, prior to the CO₂ measurements, films are pre-exposed to UVA, to generate carbonyl groups. In addition, more CO₂ is evolved from both PE and PP films if they are pre-exposed.     

Comparison of the effect of mica and talc and chemical coupling on the rheology,morphology, and mechanical properties of polypropylene composites

The effect of filler types of mica and talc on the oscillatory shear rheological properties, mechanical performance, and morphology of the chemically coupled polypropylene composites is studied in this work. The Maleic Anhydride grafted Polypropylene (MAPP) was used as an adhesion promoter for coupling mineral particles with the polypropylene matrix. The samples were prepared by a co‐rotating, L/D = 40, 25 mm twin screw extruder. The tensile tests carried out on the injection molded samples showed a reinforcing effect of talc up to 20 wt% on the Polypropylene (PP). The tensile strength of PP‐mica composites showed a slight decrease at all percentages of mica. The effect of chemical coupling by using MAPP on the tensile strength was more pronounced in increasing the tensile strength for PP‐mica than PP‐talc composites. The complex viscosity curve of pure PP and the composites, showed a Newtonian plateau (η₀) up to 30 wt% at low frequency terminal zone. By increasing the filler content to 40 and 50 wt%, the complex viscosity at very low shear rates sharply increased and showed yield behavior that can be due to the formation of filler particles networks in the melt. At the optimum amount of coupling agent, a minimum in cross over frequency curve against MAPP content is observed. The optimum amount of coupling agent for PP‐talc composites is about 1.5%, and about 3% for PP‐mica formulations. The analysis of viscosity behavior at power‐law high region, revealed the more shear thinning effect of mica than talc on the PP matrix resin. Copyright © 2009 John Wiley & Sons, Ltd.     

Determination of oxidation parameters by DSC for polypropylene stabilized with hydroxytyrosol (3,4-dihydroxy-phenylethanol)

Oxidation thermal parameters on samples of polypropylene (PP) stabilized with hydroxytyrosol were determined. For comparison purposes, α-tocopherol and a synthetic phenolic commercial antioxidant (Irganox 1076), were also analyzed. Oxidation induction time (OIt) and oxidation induction temperature (OIT) were determined by differential scanning calorimetry (DSC). The addition of hydroxytyrosol 0.1 mass% to PP was enough to obtain efficient stabilization during processing. Certain decrease in stabilizing properties of natural antioxidants was observed for compression moulded materials at high temperatures. However, these samples were still efficiently stabilized in comparison to the pure material. Hydroxytyrosol showed good performance as polypropylene antioxidant and it might be considered as promising alternative to the use of phenolic synthetic compounds.     

Studies on characterization of nano CaCO3 prepared by the in situ deposition technique and its application in PP‐nano CaCO3 composites

The elegant approach of in situ deposition technique was used for the synthesis of nano CaCO₃. the nanosize of particles was confirmed by the X‐ray diffraction (XRD) technique. Differential scanning calorimetry (DSC) was used for determination of the enthalpy. The nano CaCO₃ polypropylene (PP) composites were prepared by taking 2 and 10 wt % of different nanosizes (21–39 nm) of CaCO₃. Conversion of the α phase to β was observed in the case of 2 wt % of a 30‐nm sized amount of CaCO₃ in a PP composite. The decrement in ΔH and percent crystallinity, as well as the increment in melt temperature were recorded for 6 wt % nano CaCO₃ with a decrease in nanosize from 39 to 21 nm. The increment in tensile strength with an increase in the amount of nano CaCO₃ was observed, and the lower particle size showed greater improvement. The improvement in thermal and mechanical properties is because of the formation of a greater number of small spherulites uniformly present in the PP matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 107–113, 2004     

Study of the thermal oxidation of polyolefines—IX: Some differences in the oxidation of polyethylene and polypropylene

In the thermal oxidations of polyethylene (PE) and polypropylene (PP), both similarities and differences are found. In the initial stage, the ratio of the hydroperoxide formed and the amount of oxygen absorbed is independent of both the nature of the polymer and the actual reaction conditions. With increased conversion, however, this ratio decreases to a greater extent in the case of PE than for PP. Most of the carbonyl groups formed in the PE chain during oxidation are ketones and carboxyls, but in PP there are also carbonyls with different structure. The amount of carbonyl groups in PE is approximately 1.5 times that observed for PP. The number of scissions involving considerable molecular weight decrease is higher for PE than for PP: for identical conversions, the ratio of scissions is S_PE/S_PP ～ 6.     

Melt rheology of polypropylene containing small amounts of high molecular weight chain. I. Shear flow

Large enhancements of the melt strength of polypropylene (PP) were achieved by the introduction of high molecular weight polyethylene (PE) into PP. The viscoelastic properties of the high‐melt‐strength PP melts under shear flow were investigated. It was found that the rheological properties of the high‐melt‐strength PP were distinctly different from those of conventional PP. The elastic response at low frequencies was significantly enhanced in comparison with the conventional PP, implying a presence of a long relaxation time mode that was not revealed in conventional PP. In step‐shear measurements, the fast and slow relaxation processes that characterized the linear viscoelastic properties were observed also for nonlinear relaxation moduli. The dependence of the damping for the slow process of the high‐melt‐strength PP on shear strain was much weaker than that of the fast process. These rheological behaviors characterizing the long relaxation time mode were further enhanced with the increasing concentration of high molecular mass PE. The unusual shear rheological behaviors were discussed in view of the role of high molecular weight PE as a long relaxation time mode within PP. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2692–2704, 2001     

Different influences of nucleating agents on crystallization behavior of polyethylene and polypropylene

The crystallization behavior of polyethylene (PE) and polypropylene (PP), including the neat ones and the ones nucleated with the same nucleating agent (NA), was studied by DSC. It was found that the nucleating agent decelerated the PE nonisothermal crystallization process. NA did enhance the nucleating rates for both PE and PP, but the linear growth rate dominated the volumetric growth rate for PE, and the volumetric growth rate dominated the overall crystallization rate. That is why PE nucleated with NA had a slower overall crystallization rate than the neat one.     

Synthesis and characterization of polyethylene‐g‐polystyrene as the compatibilizer for polypropylene/ Polystyrene blends

Polyethylene‐g‐polystyrene (PE‐g‐PS) was synthesized as a compatibilizer for polypropylene/polystyrene­(PP/PS) blends by the living radical polymerization of styrene with polyethylene‐co‐glycidylmethacrylate (PE‐co‐GMA). The compatibilizer effect of PE‐g‐PS on the morphology and thermal properties of PP/PS blends was investigated. The crystalline temperature of PP in PP/PS blends decreased with increasing PE‐g‐PS contents. Morphologies of PP/PE‐g‐PS/PS blends showed much better dispersion of each domain for higher PE‐g‐PS contents. The molecular weight of PS segment in PP/PE‐g‐PS/PS blend was increased by addition of styrene monomer during the post melt blending process where post living radical polymerization reaction proceeded. Copyright © 2003 John Wiley & Sons, Ltd.