Enhanced Extraction Efficiency of Flavonoids from Pyrus ussuriensis Leaves with Deep Eutectic Solvents

In this study, deep eutectic solvents (DESs) were synthesized using different ratios of choline chloride (CC) and dicarboxylic acids, and their eutectic temperatures were determined. The DES synthesized using CC and glutaric acid (GA), which showed a higher extraction efficiency than conventional solvents, was used for the extraction of flavonoid components from Pyrus ussuriensis leaves (PUL), and the extraction efficiency was evaluated using the response surface methodology. The flavonoid components rutin, hyperoside, and isoquercitrin were identified through high-performance liquid chromatography (HPLC), equipped with a Waters 2996 PDA detector, and HPLC mass spectrometry (LC-MS/MS) analyses. The optimum extraction was achieved at a temperature of 30 °C using DES in a concentration of 30.85 wt.% at a stirring speed of 1113 rpm and an extraction time of 1 h. The corresponding flavonoid content was 217.56 μg/mL. The results were verified by performing three reproducibility experiments, and a high significance, with a confidence range of 95%, was achieved. In addition, the PUL extracts exhibited appreciable antioxidant activity. The results showed that the extraction process using the DES based on CC and GA in a 1:1 molar ratio could effectively improve the yield of flavonoids from PUL.     

Ultrasound-Assisted Extraction of Flavonoids from Potentilla fruticosa L. Using Natural Deep Eutectic Solvents

A series of natural deep eutectic solvents (NADESs) were prepared with choline chloride, betaine, and a variety of natural organic acids in order to find new environmentally-friendly green solvents to replace the traditional solvents. The NADESs were employed to extract flavonoids from Potentilla fruticosa L. (PFL) with the help of ultrasound. The eutectic solvent diluted with an appropriate amount of water improved the extraction ability of flavonoids due to the decrease of solution viscosity. The microstructure of the raw sample and the samples subjected to ultrasonic bath in different solutions were observed using scanning electron microscope (SEM) to determine the role of the NADESs in the extraction process. The DPPH method and glucose consumption method were used to study the antioxidant and hypoglycemic ability of flavonoid compounds in PFL. Single factor method and response surface methodology (RSM) were designed to analyze the effects of three extraction parameters, including solvent/solid ratio, ultrasonic power, and extraction time, on the extraction yield, antioxidant capacity, and hypoglycemic capacity, and the corresponding second-order polynomial prediction models were established. The optimal extraction conditions for the maximum extraction yield, antioxidant capacity, and hypoglycemic capacity were predicted by RSM, and the reliability of RSM simulation results was verified by a one-off experiment.     

Modelling and Optimization of Ultrasound-Assisted Extraction of Phenolic Compounds from Black Quinoa by Response Surface Methodology

Phenolic compounds are currently the most investigated class of functional components in quinoa. However, great variability in their content emerged, because of differences in sample intrinsic and extrinsic characteristics; processing-induced factors; as well as extraction procedures applied. This study aimed to optimize phenolic compound extraction conditions in black quinoa seeds by Response Surface Methodology. An ultrasound-assisted extraction was performed with two different mixtures; and the effect of time; temperature; and sample-to-solvent ratio on total phenolic content (TPC) was investigated. Data were fitted to a second-order polynomial model. Multiple regression analysis and analysis of variance were used to determine the fitness of the model and optimal conditions for TPC. Three-dimensional surface plots were generated from the mathematical models. TPC at optimal conditions was 280.25 ± 3.94 mg of Gallic Acid Equivalent (GAE) 100 g⁻¹ dm upon extraction with aqueous methanol/acetone, and 236.37 ± 5.26 mg GAE 100 g⁻¹ dm with aqueous ethanol mixture. The phenolic profile of extracts obtained at optimal conditions was also investigated by HPLC. The two extracting procedures did not show different specificities for phenolic compounds but differed in the extraction yield.     

Natural Deep Eutectic Solvents for the Extraction of Bioactive Steroidal Saponins from Dioscoreae Nipponicae Rhizoma

In the present study, a simple and environmentally friendly extraction method based on natural deep eutectic solvents (NADESs) was established to extract four bioactive steroidal saponins from Dioscoreae Nipponicae Rhizoma (DNR). A total of twenty-one types of choline chloride, betaine, and L-proline based NADESs were tailored, and the NADES composed of 1:1 molar ratio of choline chloride and malonic acid showed the best extraction efficiency for the four steroidal saponins compared with other NADESs. Then, the extraction parameters for extraction of steroidal saponins by selected tailor-made NADES were optimized using response surface methodology and the optimal extraction conditions are extraction time, 23.5 min; liquid–solid ratio, 57.5 mL/g; and water content, 54%. The microstructure of the DNR powder before and after ultrasonic extraction by conventional solvents (water and methanol) and the selected NADES were observed using field emission scanning electron microscope. In addition, the four steroidal saponins were recovered from NADESs by D101 macroporous resin with a satisfactory recovery yield between 67.27% and 79.90%. The present research demonstrates that NADESs are a suitable green media for the extraction of the bioactive steroidal saponins from DNR, and have a great potential as possible alternatives to organic solvents for efficiently extracting bioactive compounds from natural products.     

Development of Green and Efficient Extraction of Bioactive Ginsenosides from Panax ginseng with Deep Eutectic Solvents

The extraction of active constituents from natural sources in a green and efficient manner is considered an important field in the pharmaceutical industry. In recent years, deep eutectic solvents (DESs), a new type of green solvent, have attracted increasing attention. Therefore, we aimed to establish a green and high-efficiency extraction method for ginsenosides based on DESs. This study takes Panax ginseng as a model sample. Eighteen different DESs were produced to extract polar ginsenosides. Ultrasound-assisted extraction (UAE) was applied for simplicity and efficiency. A binary DES synthesized using choline chloride and urea at a proportion of 1:2 prepared by a heating stirring method is proven to be more effective than other solvents, such as the widely used 70% ethanol for the extraction of ginsenosides. Three variables that might affect the extraction, including the DES content in the extraction solvent, liquid/solid ratio, and ultrasound extraction time, were evaluated for optimization. The optimum extraction conditions for ginsenosides were determined as follows: DES water content of 20 wt%, liquid/solid ratio of 15 mL g⁻¹, and an ultrasonic extraction time of 15 min. The extraction yield for the optimized method is found to be 31% higher than that for 70% ethanol, which achieves efficient extraction. This study shows that DESs are available to extract ginsenosides for use in traditional Chinese medicine. The discovery also contributes to further research into the green extraction of ginsenosides.     

Bioactive Compounds from Ephedra fragilis: Extraction Optimization,Chemical Characterization,Antioxidant and AntiGlycation Activities

Response surface methodology (RSM) with a Box–Behnken design (BBD) was used to optimize the extraction of bioactive compounds from Ephedra fragilis. The results suggested that extraction with 61.93% ethanol at 44.43 °C for 15.84 h was the best solution for this combination of variables. The crude ethanol extract (CEE) obtained under optimum extraction conditions was sequentially fractionated with solvents of increasing polarity. The content of total phenolic (TP) and total flavonoid (TF) as well as the antioxidant and antiglycation activities were measured. The phytochemical fingerprint profile of the fraction with the highest activity was characterized by using RP-HPLC. The ethyl acetate fraction (EAF) had the highest TP and TF contents and exhibited the most potent antioxidant and antiglycation activities. The Pearson correlation analysis results showed that TP and TF contents were highly significantly correlated with the antioxidant and antiglycation activities. Totally, six compounds were identified in the EAF of E. fragilis, including four phenolic acids and two flavonoids. Additionally, molecular docking analysis also showed the possible connection between identified bioactive compounds and their mechanisms of action. Our results suggest new evidence on the antioxidant and antiglycation activities of E. fragilis bioactive compounds that may be applied in the treatment and prevention of aging and glycation-associated complications.     

Ultrasound-Assisted Extraction of Phenolic Compounds from Psidium cattleianum Leaves: Optimization Using the Response Surface Methodology

In this study, conditions for the ultrasound-assisted extraction (UAE) of soluble polyphenols from Psidium cattleianum (PC) leaves were optimized using response surface methodology (RSM) by assessing the effect of extraction time (X_ET = 2, 4, and 6 min), sonication amplitude (X_SA = 60, 80, and 100%), and pulse cycle (X_PC = 0.4, 0.7, and 1 s). Furthermore, the optimized UAE conditions were compared with a conventional aqueous–organic extraction (AOE) method for extracting total phenolics; moreover, a phenolic profile using HPLC and antioxidant activity (DPPH, ABTS, and FRAP) were also compared. According to the RSM, the best conditions for UAE to extract the highest soluble polyphenol content and yield (158.18 mg/g dry matter [DM] and 15.81%) include a 100% sonication amplitude for 4 min at 0.6 s of pulse cycle. The optimal UAE conditions exhibited an effectiveness of 1.71 times in comparison to the AOE method for extracting total phenolics, in 96.66% less time; moreover, PC leaf extracts by UAE showed higher antioxidant values than AOE. Additionally, gallic, protocateic, chlorogenic, caffeic, coumaric, trans-cinnamic, 4-hydroxybenzoic, and syringic acids, as well as kaempferol were identified in PC leaves under UAE. PC leaf extracts are widely used for therapeutic and other industrial purposes; thus, the UAE proves to be a useful technology with which to improve the yield extraction of PC leaf phytochemicals.     

Choline Chloride–Lactic Acid-Based NADES As an Extraction Medium in a Response Surface Methodology-Optimized Method for the Extraction of Phenolic Compounds from Hazelnut Skin

Deep eutectic solvents (DESs) are promising green solvents for the extraction of compounds from food byproducts. Hazelnut (Corylus avellana L.) is one of the most commonly cultivated tree nuts worldwide. The skin represents one of the major byproducts of the hazelnut industry and accounts for 2.5% of the total hazelnut kernel weight. It is a rich source of phenolic compounds like flavan-3-ols, flavonols, dihydrochalcones, and phenolic acids. In this work, fifteen DESs based on choline chloride and betaine, with different compositions, were studied in order to test their phenolic compounds extraction efficiency through the determination of their total concentration via Folin–Ciocalteu assay. A qualitative analysis of extracted phenolic compounds was assessed by HPLC with UV and MS detection. Using the DES with the best extraction efficiency, a new ultrasound-assisted solid liquid extraction (UA-SLE) method was optimized though the response surface methodology (RSM), taking into account some extraction parameters. Efficient recovery of extracted phenolic compounds was achieved using a 35% water solution of choline chloride and lactic acid (molar ratio 1:2) as an extraction solvent, working at 80 °C and with a solid-to-solvent ratio of 1:25 gmL⁻¹. The optimized conditions made it possible to recover 39% more phenolic compounds compared to a classic organic solvent.     

Efficient Extraction of Fermentation Inhibitors by Means of Green Hydrophobic Deep Eutectic Solvents

The methods for hydrogen yield efficiency improvements, the gaseous stream purification in gaseous biofuels generation, and the biomass pretreatment are considered as the main trends in research devoted to gaseous biofuel production. The environmental aspect related to the liquid stream purification arises. Moreover, the management of post-fermentation broth with the application of various biorefining techniques gains importance. Chemical compounds occurring in the exhausted liquid phase after biomass pretreatment and subsequent dark and photo fermentation processes are considered as value-added by products. The most valuable are furfural (FF), 5-hydroxymethylfurfural (HMF), and levulinic acid (LA). Enriching their solutions can be carried with the application of liquid–liquid extraction with the use of a suitable solvent. In these studies, hydrophobic deep eutectic solvents (DESs) were tested as extractants. The screening of 56 DESs was carried out using the Conductor-like Screening Model for Real Solvents (COSMO-RS). DESs which exposed the highest inhibitory effect on fermentation and negligible water solubility were prepared. The LA, FF, and HMF were analyzed using FT-IR and NMR spectroscopy. In addition, the basic physicochemical properties of DES were carefully studied. In the second part of the paper, deep eutectic solvents were used for the extraction of FF, LA, and HMF from post-fermentation broth (PFB). The main extraction parameters, i.e., temperature, pH, and DES: PFB volume ratio (V_DES:V_PFB), were optimized by means of a Box–Behnken design model. Two approaches have been proposed for extraction process. In the first approach, DES was used as a solvent. In the second, one of the DES components was added to the sample, and DES was generated in situ. To enhance the post-fermentation broth management, optimization of the parameters promoting HMF, FF, and LA extraction was carried under real conditions. Moreover, the antimicrobial effect of the extraction of FF, HMF, and LA was investigated to define the possibility of simultaneous separation of microbial parts and denatured peptides via precipitation.     

Comparative Studies of Selected Criteria Enabling Optimization of the Extraction of Polar Biologically Active Compounds from Alfalfa with Supercritical Carbon Dioxide

The aim of this research was to provide crucial and useful data about the selection of the optimization criteria of supercritical carbon dioxide extraction of alfalfa at a quarter-technical plant. The correlation between more general output, including total phenolics and flavonoids content, and a more specified composition of polar constituents was extensively studied. In all alfalfa extracts, polar bioactive constituents were analyzed by both spectrometric (general output) and chromatographic (detailed output) analyses. Eight specific phenolic acids and nine flavonoids were determined. The most dominant were salicylic acid (221.41 µg g⁻¹), ferulic acid (119.73 µg g⁻¹), quercetin (2.23 µg g⁻¹), and apigenin (2.60 µg g⁻¹). For all seventeen analyzed compounds, response surface methodology and analysis of variance were used to provide the optimal conditions of supercritical fluid extraction for each individual constituent. The obtained data have shown that eight of those compounds have a similar range of optimal process parameters, being significantly analogous for optimization based on total flavonoid content.     

Natural Deep Eutectic Solvent-Based Microwave-Assisted Extraction of Total Flavonoid Compounds from Spent Sweet Potato (Ipomoea batatas L.) Leaves: Optimization and Antioxidant and Bacteriostatic Activity

Natural deep eutectic solvents (NADESs) coupled with microwave-assisted extraction (MAE) were applied to extract total flavonoid compounds from spent sweet potato (Ipomoea batatas L.) leaves. In this study, ten different NADESs were successfully synthesized for the MAE. Based on single-factor experiments, the response surface methodology (RSM) was applied, and the microwave power, extraction temperature, extraction time, and solid–liquid ratio were further evaluated in order to optimize the yields of total flavonoid compounds. Besides, the extracts were recovered by macroporous resin for the biological activity detection of flavonoid compounds. As a result, NADES-2, synthesized by choline chloride and malic acid (molar ratio 1:2), exhibited the highest extraction yield. After that, the NADES-2-based MAE process was optimized and the optimal conditions were as follows: microwave power of 470 W, extraction temperature of 54 °C, extraction time of 21 min, and solid–liquid ratio of 70 mg/mL. The extraction yield (40.21 ± 0.23 mg rutin equivalents/g sweet potato leaves) of the model validation experiment was demonstrated to be in accordance with the predicted value (40.49 mg rutin equivalents/g sweet potato leaves). In addition, flavonoid compounds were efficiently recovered from NADES-extracts with a high recovery yield (>85%) using AB-8 macroporous resin. The bioactivity experiments in vitro confirmed that total flavonoid compounds had good DPPH and O₂⁻· radical-scavenging activity, as well as inhibitory effects on E. coli, S. aureus, E. carotovora, and B. subtilis. In conclusion, this study provides a green and efficient method to extract flavonoid compounds from spent sweet potato leaves, providing technical support for the development and utilization of sweet potato leaves’ waste.     

Latest Insights on Novel Deep Eutectic Solvents (DES) for Sustainable Extraction of Phenolic Compounds from Natural Sources

Phenolic compounds have long been of great importance in the pharmaceutical, food, and cosmetic industries. Unfortunately, conventional extraction procedures have a high cost and are time consuming, and the solvents used can represent a safety risk for operators, consumers, and the environment. Deep eutectic solvents (DESs) are green alternatives for extraction processes, given their low or non-toxicity, biodegradability, and reusability. This review discusses the latest research (in the last two years) employing DESs for phenolic extraction, solvent components, extraction yields, extraction method characteristics, and reviewing the phenolic sources (natural products, by-products, wastes, etc.). This work also analyzes and discusses the most relevant DES-based studies for phenolic extraction from natural sources, their extraction strategies using DESs, their molecular mechanisms, and potential applications.     

Solvent Mixture Optimization in the Extraction of Bioactive Compounds and Antioxidant Activities from Garlic (Allium sativum L.)

Garlic is a health promoter that has important bioactive compounds. The bioactive extraction is an important step in the analysis of constituents present in plant preparations. The purpose of this study is to optimize the extraction with the best proportion of solvents to obtain total phenolic compounds (TPC) and thiosulfinates (TS) from dried garlic powder, and evaluate the antioxidant activities of the optimized extracts. A statistical mixture simplex axial design was used to evaluate the effect of solvents (water, ethanol, and acetone), as well as mixtures of these solvents, after two ultrasound extraction cycles of 15 min. Results showed that solvent mixtures with a high portion of water and pure water were efficient for TPC and TS recovery through this extraction procedure. According to the regression model computed, the most significant solvent mixtures to obtain high TPC and TS recovery from dried garlic powder are, respectively, the binary mixture with 75% water and 25% acetone and pure water. These optimized extracts presented oxygen radical absorbance capacity. Pure water was better for total antioxidant capacity, and the binary mixture of water–acetone (75:25) was better for DPPH scavenging activity. These optimized extracts can be used for industrial and research applications.     

Extraction of Bioactive Components from Chamaenerion angustifolium (L.) Scop. with Choline Chloride and Organic Acids Natural Deep Eutectic Solvents

Chamaenerion angustifolium (L.) Scop. (fireweed) is a perennial herbaceous plant of the Onagraceae family widely used in folk and scientific medicine. It is a promising source of bioactive components. One of the modern trends in extraction is the use of natural deep eutectic solvents (NADESs) combined with ultrasound-assisted extraction (UAE). However, works devoted to the extraction of biologically active substances from C. angustifolium using NADESs are scarce. The aim of this work is a comprehensive study of UAE of bioactive components from C. angustifolium using NADESs based on choline chloride and malonic, malic, tartaric, and citric acids. The antioxidative properties, total phenols, and flavonoids content were estimated for NADES-based extracts. The reference solvents were water and 90% v/v ethanol. Volatile extracted components were identified using GC-MS. The kinetics of the UAE were studied at 45 °C for 20–180 min with water added to 30 wt% NADES. The power of the ultrasound was 120 W, and the frequency was 40 kHz. It was found that NADES choline chloride + citric acid is more effective for the extraction of bioactive components. For this, NADES UAE conditions were optimized following a Box–Behnken design of the experiment and a response surface methodology. The temperature ranged from 30 to 60 °C, the time of extraction ranged from 20 to 60, and the addition of water ranged from 30 to 70 wt%. We established the optimal extraction conditions: temperature 58 °C, time of extraction 35 min, and 70 wt% water. The obtained results expand the knowledge about the use of NADES for the extraction of biologically active compounds from cheap and available plant raw materials.     

Valorization of Phenolic and Carotenoid Compounds of Sechium edule (Jacq. Swartz) Leaves: Comparison between Conventional,Ultrasound- and Microwave-Assisted Extraction Approaches

Chayote leaves are known for culinary and traditional medicine applications. This work intended to recover carotenoids and phenolic compounds from chayote leaves using the ultrasound-assisted extraction (UAE). A Box–Behnken design was employed to investigate the impact of extraction time, temperature, and ultrasonic power on the recovery of total carotenoids, total phenolic compounds, and antioxidant activities. For comparative purposes, chayote leaf extracts were prepared by maceration (ME) and microwave-assisted extraction (MAE), using the same time and temperature conditions optimized by UAE. Extraction at 50 °C and 170 Watts for 30 min provided the optimal UAE conditions. UAE showed better extraction efficacy than ME and MAE. The HPLC analysis of the extracts showed that the xanthophyll class was the main class of carotenoids, which constituted 42–85% of the total carotenoid content, followed by β-carotene and tocopherol. Moreover, 26 compounds, classified as phenolic acids, flavonols, flavonoids and other polar compounds, were identified in the chayote leaf extracts. Flavonols accounted for 55% of the total compounds quantified (the major compound was myricetin) and phenolic acids represented around 35%, mostly represented by ferulic acid, chlorogenic acid and (+)-catechin. This study revealed the potential of UAE as an effective green extraction technique to recover bioactive compounds from chayote leaves, for food, and for pharmaceutical and cosmetic applications.     

The Effect of Maturity and Extraction Solvents on Bioactive Compounds and Antioxidant Activity of Mulberry (Morus alba) Fruits and Leaves

Cultivation location, maturity levels, and extraction solvents could affect the bioactive compounds and biological activities of mulberry (Morus alba Linnaeus). The lack of study on Malaysia-grown mulberry causes its underutilization. This study investigated the bioactive compound content and the antioxidant activity of Sabah-grown mulberry at two different maturity stages (fruits: red mature and black fully ripe; leaves: young and mature) extracted using 70% (v/v) methanol, 60% (v/v) ethanol, and 65% (v/v) acetone. Analyses showed that mulberry fruits demonstrated maturity-dependent increment (except UHPLC-DAD quantification), while the leaves revealed maturity-dependent reduction. Principal component analysis (PCA) displayed 65% (v/v) acetone black fully ripe fruits as the best phenolics and antioxidant sources. However, the 60% (v/v) ethanol black fully ripe fruits contained 20.08–68.43% higher total anthocyanins. Meanwhile, the 65% (v/v) acetone and 70% (v/v) methanol red mature fruits were higher in chlorogenic acid (27.53–47.12%) and rutin (31.42–35.92%) than other fruit extracts, respectively. For leaves, 65% (v/v) acetone young leaves were the best phenolics and antioxidant sources. However, the 60% (v/v) ethanol young leaves possessed greater chlorogenic acid (19.56–74.11%) than other leaf extracts. Overall, Malaysia-grown mulberry is rich in phenolics and antioxidants, suggesting its potential application in food and pharmaceutical products.     

Effects of Orange Leaves Extraction Conditions on Antioxidant and Phenolic Content: Optimization Using Response Surface Methodology

In the last few years, bioactive components or their extraction techniques are gaining special interest in scientific areas. In this framework, orange leaves were used for preparation of extracts with high content of biologically active compounds. To optimize the extraction process, three levels and three variables of Box–Behnken design with response surface methodology were applied. Investigated responses were the total phenolic content (TPC), 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical, cupric ion reducing antioxidant capacity (CUPRAC), and ferric reducing antioxidant power (FRAP). Independent variables were methanol concentration (10–90%), temperature (20–60°C), and extraction time (60–180?min). Experimentally obtained results were fit into a second-order polynomial model with multiple regression. Analysis of variance was used to estimate model fitness and determine optimal conditions for processing. Estimated optimal conditions were 90% methanolic solution, 60°C and 180?min using these parameters; the predicted values of investigated responses were 43.19?mg GAE/g (GAE: gallic acid equivalents), 43.04?mg TE/g (TE: trolox equivalents), 139.34 and 93.76?mg TE/g for TPC, DPPH, CUPRAC, and FRAP, respectively. The obtained optimal conditions could be considered as an alternative strategy for developing novel functional products.     

Obtaining Bioactive Compounds from the Coffee Husk (Coffea arabica L.) Using Different Extraction Methods

Coffee husks (Coffea arabica L.) are characterized by exhibiting secondary metabolites such as phenolic compounds, which can be used as raw material for obtaining bioactive compounds of interest in food. The objective of this study is to evaluate different methods for obtaining the raw material and extracting solutions of bioactive compounds from coffee husks. Water bath and ultrasound-assisted extraction methods were used, using water (100%) or ethanol (100%) or a mixture of both (1:1) as extracting solutions and the form of the raw material was in natura and dehydrated. The extracts were evaluated by their antioxidant potential using DPPH radicals, ABTS, and iron reduction (ferric reducing antioxidant power (FRAP)), and later total phenolic compounds, total flavonoids, and condensed tannins were quantified the phenolic majority compounds were identified. It was verified that the mixture of water and ethanol (1:1) showed better extraction capacity of the compounds with antioxidant activity and that both conventional (water bath) or unconventional (ultrasound) methods showed satisfactory results. Finally, a satisfactory amount of bioactive compounds was observed in evaluating the chemical composition (total phenolic compounds, total flavonoids, condensed tannins, as well as the analysis of the phenolic profile) of these extracts. Corroborating with the results of the antioxidant activities, the best extracting solution was generally the water and ethanol mixture (1:1) using a dehydrated husk and water bath as the best method, presenting higher levels of the bioactive compounds in question, with an emphasis on chlorogenic acid. Thus, it can be concluded that the use of coffee husk as raw material to obtain extracts of bioactive compounds is promising. Last, the conventional method (water bath) and the water and ethanol mixture (1:1) stood out among the methods and extracting solutions used for the dehydrated coffee husk.     

Extraction,Isolation and Characterization of Bioactive Compounds from Artemisia and Their Biological Significance: A Review

Diverse medicinal plants such as those from the genus Artemisia have been employed globally for centuries by individuals belonging to different cultures. Universally, Artemisia species have been used to remedy various maladies that range from simple fevers to malaria. A survey conducted by the World Health Organization (WHO) demonstrated that 80% of the global population is highly reliant on herbal medicine for their primary healthcare. WHO recommends artemisinin-based combination therapies (ACT) for the treatment of global diseases such as malaria. Artemisinin is a bioactive compound derived from Artemisia annua leaves. It is a sesquiterpene endoperoxide with potent antimalarial properties. This review strives to instill natural products to chemists and others in diverse fields with a heterogeneous set of knowledge compiled from multifaceted researchers and organizations in literature. In particular, the various Artemisia species and effective extraction, isolation, and characterization methodologies are discussed in detail. An in-depth investigation into the literature reveals that divergent species of Artemisia exhibit a vast array of biological activities such as antimalarial, antitumor, and anti-inflammatory activities. There is substantial potential for bioactive compounds from Artemisia to provide significant relief from differing human ailments, but more meticulous research in this field is needed.     

响应面法优化黄芪多糖的提取工艺研究

为优化对黄芪多糖提取工艺.根据单因素实验结果,选取实验因素与水平,根据Box - Benhnken的试验设计原理,采用三因素三水平的响应面分析法,以获得多元二次线性回归方程,以多糖得率为响应值的响应面和等高线.结果表明,提取黄芪多糖最佳工艺条件:料水比1:13,提取温度94 ℃,提取时间64 min.在此条件下,黄芪多...