Suppression of the primary resonance vibrations of a forced nonlinear system using a dynamic vibration absorber

In a single degree-of-freedom weakly nonlinear oscillator subjected to periodic external excitation, a small-amplitude excitation may produce a relatively large-amplitude response under primary resonance conditions. Jump and hysteresis phenomena that result from saddle-node bifurcations may occur in the steady-state response of the forced nonlinear oscillator. A simple mass-spring-damper vibration absorber is thus employed to suppress the nonlinear vibrations of the forced nonlinear oscillator for the primary resonance conditions. The values of the spring stiffness and mass of the vibration absorber are significantly lower than their counterpart of the forced nonlinear oscillator. Vibrational energy of the forced nonlinear oscillator is transferred to the attached light mass through linked spring and damper. As a result, the nonlinear vibrations of the forced oscillator are greatly reduced and the vibrations of the absorber are significant. The method of multiple scales is used to obtain the averaged equations that determine the amplitude and phases of the first-order approximate solutions to primary resonance vibrations of the forced nonlinear oscillator. Illustrative examples are given to show the effectiveness of the dynamic vibration absorber for suppressing primary resonance vibrations. The effects of the linked spring and damper and the attached mass on the reduction of nonlinear vibrations are studied with the help of frequency response curves, the attenuation ratio of response amplitude and the desensitisation ratio of the critical amplitude of excitation.     

Transient analysis of nonlinear Euler–Bernoulli micro-beam with thermoelastic damping,via nonlinear normal modes

In this paper an Euler–Bernoulli model has been used for vibration analysis of micro-beams with large transverse deflection. Thermoelastic damping is considered to be the dominant damping mechanism and introduced as imaginary stiffness into the equation of motion by evaluating temperature profile as a function of lateral displacement. The obtained equation of motion is analyzed in the case of pure single mode motion by two methods; nonlinear normal mode theory and the Galerkin procedure. In contrast with the Galerkin procedure, nonlinear normal mode analysis introduces a nonconventional nonlinear damping term in modal oscillator which results in strong damping in case of large amplitude vibrations. Evaluated modal oscillators are solved using harmonic balance method and tackling damping terms introduced as an imaginary stiffness is discussed. It has been shown also that nonlinear modal analysis of micro-beam with thermoelastic damping predicts parameters such as inverse quality factor, and frequency shift, to have an extrema point at certain amplitude during transient response due to the mentioned nonlinear damping term; and the effect of system?s characteristics on this critical amplitude has also been discussed.     

Toward an adjustable nonlinear low frequency acoustic absorber

A study of the targeted energy transfer (TET) phenomenon between an acoustic resonator and a thin viscoelastic membrane has recently been presented in the paper [R. Bellet et al., Experimental study of targeted energy transfer from an acoustic system to a nonlinear membrane absorber, Journal of Sound and Vibration 329 (2010) 2768-2791], providing a new path to passive sound control in the low frequency domain where no efficient dissipative device exists. This paper presents experimental results showing that a loudspeaker used as a suspended piston working outside its range of linearity can also be used as a nonlinear acoustic absorber. The main advantage of this technology of absorber is the perspective to adjust independently the device parameters (mass, nonlinear stiffness and damping) according to the operational conditions. To achieve this purpose, quasi-static and dynamic tests have been performed on three types of commercial devices (one with structural modi?cations), in order to de?ne the constructive characteristics that it should present. An experimental setup has been developed using a one-dimensional acoustic linear system coupled through a box (acting as a weak spring) to a loudspeaker used as a suspended piston acting as an essentially nonlinear oscillator. The tests carried out on the whole vibro-acoustic system have showed the occurrence of the acoustic TET from the acoustic media to the suspended piston and demonstrated the efficiency of this new kind of absorber at low frequencies over a wide frequency range. Moreover, the experimental analyses conducted with different NES masses have con?rmed that it is possible to optimize the noise absorption with respect to the excitation level of the acoustic resonator.     

Hysteretic damping and causality

It is proven that linear oscillatory systems with hysteretic damping in the form of complex stiffness and/or complex elastic moduli satisfy the causality principle: the response of such a system to an arbitrary external force cannot appear earlier than the onset of the force. The proof, based on a rigorous solution to the problem of forced oscillations, is presented in detail for an oscillator with a complex stiffness, as well as in a brief explanation for a system with N mass. It is also shown that these systems are Lyapunov-unstable. A comparison is made to other linear hysteretic damping models.     

M-shaped asymmetric nonlinear oscillator for broadband vibration energy harvesting: Harmonic balance analysis and experimental validation

Over the past few years, nonlinear oscillators have been given growing attention due to their ability to enhance the performance of energy harvesting devices by increasing the frequency bandwidth. Duffing oscillators are a type of nonlinear oscillator characterized by a symmetric hardening or softening cubic restoring force. In order to realize the cubic nonlinearity in a cantilever at reasonable excitation levels, often an external magnetic field or mechanical load is imposed, since the inherent geometric nonlinearity would otherwise require impractically high excitation levels to be pronounced. As an alternative to magnetoelastic structures and other complex forms of symmetric Duffing oscillators, an M-shaped nonlinear bent beam with clamped end conditions is presented and investigated for bandwidth enhancement under base excitation. The proposed M-shaped oscillator made of spring steel is very easy to fabricate as it does not require extra discrete components to assemble, and furthermore, its asymmetric nonlinear behavior can be pronounced yielding broadband behavior under low excitation levels. For a prototype configuration, linear and nonlinear system parameters extracted from experiments are used to develop a lumped-parameter mathematical model. Quadratic damping is included in the model to account for nonlinear dissipative effects. A multi-term harmonic balance solution is obtained to study the effects of higher harmonics and a constant term. A single-term closed-form frequency response equation is also extracted and compared with the multi-term harmonic balance solution. It is observed that the single-term solution overestimates the frequency of upper saddle-node bifurcation point and underestimates the response magnitude in the large response branch. Multi-term solutions can be as accurate as time-domain solutions, with the advantage of significantly reduced computation time. Overall, substantial bandwidth enhancement with increasing base excitation is validated experimentally, analytically, and numerically. As compared to the 3 dB bandwidth of the corresponding linear system with the same linear damping ratio, the M-shaped oscillator offers 3200, 5600, and 8900 percent bandwidth enhancement at the root-mean-square base excitation levels of 0.03g, 0.05g, and 0.07g, respectively. The M-shaped configuration can easily be exploited in piezoelectric and electromagnetic energy harvesting as well as their hybrid combinations due to the existence of both large strain and kinetic energy regions. A demonstrative case study is given for electromagnetic energy harvesting, revealing the importance of higher harmonics and the need for multi-term harmonic balance analysis for predicting the electrical power output accurately.     

Vibrational resonance in the Morse oscillator

The occurrence of vibrational resonance is investigated in both classical and quantum mechanical Morse oscillators driven by a biharmonic force. The biharmonic force consists of two forces of widely different frequencies ω and Ω with Ω???ω. In the damped and biharmonically driven classical Morse oscillator, by applying a theoretical approach, an analytical expression is obtained for the response amplitude at the low-frequency ω. Conditions are identified on the parameters for the occurrence of resonance. The system shows only one resonance and moreover at resonance the response amplitude is 1/dω where d is the coefficient of linear damping. When the amplitude of the high-frequency force is varied after resonance the response amplitude does not decay to zero but approaches a nonzero limiting value. It is observed that vibrational resonance occurs when the sinusoidal force is replaced by a square-wave force. The occurrence of resonance and antiresonance of transition probability of quantum mechanical Morse oscillator is also reported in the presence of the biharmonic external field.     

On the efficacy of an active absorber with internal state feedback for controlling self-excited oscillations

An active absorber, utilizing the state feedback of the absorber mass, is proposed for controlling the self-excited vibration of a single degree-of-freedom extended Rayleigh oscillator. The control strategy renders the design standalone. The process of optimizing the control gains is discussed. The analysis reveals that by selecting a suitably high value of the absorber frequency, the overall damping of the system can be made as high as the critical damping irrespective of the amount of negative linear damping present in the primary self-excited system. It is shown that a higher value of the absorber frequency is profitable in almost all respects related to the performance as well as the robustness of the system under parametric uncertainty. The nonlinear analysis of the system reveals that the proposed absorber can control the amplitude of oscillation even in case detuning (up to some limit) of the absorber frequency from its nominal value. The region of global stability increases with the increase in the value of the absorber frequency. However some aspects, like higher absorber deflection, reduced lower bound of the admissible detuning and the lower range of the tolerance on the mass ratio limit using a very high value of absorber frequency. The results of numerical simulations confirm the analytical results.     

非线性弹簧阻尼减振装置的探究

将汽车底盘减振装置简化为以非线性弹簧、阻尼器为主的被动阻尼式吸振器．利用Matlab软件对其在简谐力作用下的响应进行定量绘图分析,研究其振幅衰减、缓冲周期以及与由线性弹簧构成的简单模型进行比较,解释了减振装置具体的工作过程以及其中的基本工作原理．     

分数阶van der Pol振子的超谐共振

以含分数阶微分项的van der Pol振子为对象,研究其超谐共振时的动力学特性.首先,通过平均法得到了系统的一阶近似解,提出了超谐共振时等效线性阻尼和等效线性刚度的概念,研究了分数阶微分项的系数和阶次以等效线性阻尼和等效线性刚度的形式对系统动力学特性的影响.随后,建立了超谐共振时定常解的幅频曲线的解析表达式,得到了超谐共振周期响应的稳定性判断准则并提出等效非线性阻尼和非线性稳定性条件参数的概念.最后,通过数值仿真比较了分数阶与整数阶系统的幅频曲线,分析了分数阶微分项的系数和阶次对响应幅值、幅频曲线以及系统稳定性的影响.     

H-infinity optimization of a variant design of the dynamic vibration absorber—Revisited and new results

The H_∞ optimum parameters of a dynamic vibration absorber (DVA) with ground-support are derived to minimize the resonant vibration amplitude of a single degree-of-freedom (sdof) system under harmonic force excitation. The optimum parameters which are derived based on the classical fixed-points theory and reported in literature for this non-traditional DVA are shown to be not leading to the minimum resonant vibration amplitude of the controlled mass. A new procedure is proposed for the H_∞ optimization of such a dynamic vibration absorber. A new set of optimum tuning frequency and damping of the absorber is derived, thereby resulting in lower maximum amplitude responses than those reported in the literature. The proposed optimized variant DVA is also compared to a ground-hooked damper of the same damping capacity of the damper in the DVA. It is proved that the proposed optimized DVA has better suppression of the resonant vibration amplitude of the controlled system than both the traditional DVA and also the ground-hooked damper if the proposed design procedure of the variant DVA is followed.     

A general mass law for broadband energy harvesting

It is well known that the power absorbed by a linear oscillator when excited by white noise base acceleration depends only on the mass of the oscillator and the spectral density of the base motion. This places an upper bound on the energy that can be harvested from a linear oscillator under broadband excitation, regardless of the stiffness of the system or the damping factor. It is shown here that the same result applies to any multi-degree-of-freedom nonlinear system that is subjected to white noise base acceleration: for a given spectral density of base motion the total power absorbed is proportional to the total mass of the system. The only restriction to this result is that the internal forces are assumed to be a function of the instantaneous value of the state vector. The result is derived analytically by several different approaches, and numerical results are presented for an example two-degree-of-freedom-system with various combinations of linear and nonlinear damping and stiffness.     

Response of SDOF nonlinear oscillators with lightly fractional derivative damping under real noise excitations

This paper deals with the response of single-degree-of-freedom (SDOF) strongly nonlinear oscillator with lightly fractional derivative damping to external and (or) parametric real noise excitations. First, the state vector of the displacement and the velocity is approximated by one-dimensional time-homogeneous diffusive Markov process of amplitude through using the stochastic averaging method. Then, the stationary probability density of amplitude is obtained by solving the Fokker-Planck-Kolmogorov (FPK) equation associated with the averaged It? equation of amplitude, in which the Fourier series expansions are used to obtain the explicit expressions of the drift and diffusion coefficients. Finally, the response of a Duffing oscillator with lightly fractional derivative damping under external and parametric real noise excitations is evaluated by using the proposed procedure and compared with that from the Monte Carlo simulation of original system.     

On the response of a harmonically excited two degree-of-freedom system consisting of a linear and a nonlinear quasi-zero stiffness oscillator

There are many systems which consist of a nonlinear oscillator attached to a linear system, examples of which are nonlinear vibration absorbers, or nonlinear systems under test using shakers excited harmonically with a constant force. This paper presents a study of the dynamic behaviour of a specific two degree-of-freedom system representing such a system, in which the nonlinear system does not affect the vibration of the forced linear system. The nonlinearity of the attachment is derived from a geometric configuration consisting of a mass suspended on two springs which are adjusted to achieve a quasi-zero stiffness characteristic with pure cubic nonlinearity. The response of the system at the frequency of excitation is found analytically by applying the method of averaging. The effects of the system parameters on the frequency-amplitude response of the relative motion are examined. It is found that closed detached resonance curves lying outside or inside the continuous path of the main resonance curve can appear as a part of the overall amplitude-frequency response. Two typical situations for the creation of the detached resonance curve inside the main resonance curve, which are dependent on the damping in the nonlinear oscillator, are discussed.     

Vibration isolation via a scissor-like structured platform

More and more attentions are attracted to the analysis and design of nonlinear vibration control/isolation systems for better isolation performance. In this study, an isolation platform with n-layer scissor-like truss structure is investigated to explore novel design of passive/semi-active/active vibration control/isolation systems and to exploit potential nonlinear benefits in vibration suppression. Due to the special scissor-like structure, the dynamic response of the platform has inherent nonlinearities both in equivalent damping and stiffness characteristics (although only linear components are applied), and demonstrates good loading capacity and excellent equilibrium stability. With the mathematical modeling and analysis of the equivalent stiffness and damping of the system, it is shown that: (a) the structural nonlinearity in the system is very helpful in vibration isolation, (b) both equivalent stiffness and damping characteristics are nonlinear and could be designed/adjusted to a desired nonlinearity by tuning structural parameters, and (c) superior vibration isolation performances (e.g., quasi-zero stiffness characteristics etc.) can be achieved with different structural parameters. This scissor-like truss structure can potentially be employed in different engineering practices for much better vibration isolation or control.     

A class of solvable coupled nonlinear oscillators with amplitude independent frequencies

Existence of amplitude independent frequencies of oscillation is an unusual property for a nonlinear oscillator. We find that a class of N coupled nonlinear Liénard type oscillators exhibit this interesting property. We show that a specific subset can be explicitly solved from which we demonstrate the existence of periodic and quasiperiodic solutions. Another set of N coupled nonlinear oscillators, possessing the amplitude independent nature of frequencies, is almost integrable in the sense that the system can be reduced to a single nonautonomous first order scalar differential equation which can be easily integrated numerically.     

Instabilities in the main parametric resonance area of a mechanical system with a pendulum

Vibrations of an autoparametric system, composed of a nonlinear mechanical oscillator with an attached damped pendulum, around the principal resonance region, are investigated in this paper. Approximate analytical solutions of the model are determined on the basis of the Harmonic Balance Method (HBM). Correctness of the analytical results is verified by numerical simulations and experimental tests performed on an especially prepared experimental rig. The influence of all essential parameters such as damping, excitation amplitude and frequency, nonlinear stiffness of the spring, on the localisation of the instability region and the system dynamics is presented in the work. Regions of regular system oscillations, chaotic motions, and full rotation of the pendulum are confirmed experimentally.     

Wave attenuation in nonlinear periodic structures using harmonic balance and multiple scales

We study the attenuation, caused by weak damping, of harmonic waves through a discrete, periodic structure with frequency nominally within the Propagation Zone (i.e., propagation occurs in the absence of the damping). The period of the structure consists of a linear stiffness and a weak linear/nonlinear damping. Adapting the transfer matrix method and using harmonic balance for the nonlinear terms, a four-dimensional linear/nonlinear map governing the dynamics is obtained. We analyze this map by applying the method of multiple scales upto first order. The resulting slow evolution equations give the amplitude decay rate in the structure. The approximations are validated by comparing with other analytical solutions for the linear case and full numerics for the nonlinear case. Good agreement is obtained. The method of analysis presented here can be extended to more complex structures.     

Stability improvement and regenerative chatter suppression in nonlinear milling process via tunable vibration absorber

In this paper, a tunable vibration absorber set (TVAs) is designed to suppress regenerative chatter in milling process (as a semi-active controller). An extended dynamic model of the peripheral milling with closed form expressions for the nonlinear cutting forces is presented. The extension part of the cutting tool is modeled as an Euler–Bernoulli beam with in plane lateral vibrations (x–y directions). Tunable vibration absorbers in x–y directions are composed of mass, spring and dashpot elements. In the presence of regenerative chatter, coupled dynamics of the system (including the beam and x–y absorbers) is described through nonlinear delay differential equations. Using an optimal algorithm, optimum values of the absorbers' position and their springs' stiffness in both x–y directions are determined such that the cutting tool vibration is minimized. Results are compared for both linear and nonlinear models. According to the results obtained, absorber set acts effectively in chatter suppression over a wide range of chatter frequencies. Stability limits are obtained and compared with two different approaches: a trial and error based algorithm and semi-discretization method. It is shown that in the case of self-excited vibrations, the optimum absorber improves the process stability. Therefore, larger values of depth of cut and consequently more material removal rate (MRR) can be achieved without moving to unstable conditions.     

Use of modal energy transfer as a new damping device with controllable bandwidth

This paper presents a new design of nonlinear dynamic absorber (NDA) using the phenomenon of modal energy transfer between the symmetric mode and the anti-symmetric mode of a curved beam. It can reduce the resonance vibration of a primary structure with a controllable operational frequency range. The energy transfer is initiated by an autoparametric vibration and the excitation force required is lowest when the ratio of the resonance frequencies of the first symmetric mode (ω₁) and first anti-symmetric mode (ω₂) is close to 2.The resonance frequency of the first anti-symmetric mode (ω₂) can be altered to control the operational frequency range. The autoparametric vibration response can be used to create an energy-dissipative region with a controllable bandwidth. It is also possible to create a non-dissipative region in between two dissipative regions. This is useful for providing damping for a conventional dynamic absorber without adding high damping material. The damping is due to the dissipation of energy to anti-symmetric mode. Numerical calculations indicate that the resonance vibration of a primary structure can be successfully reduced using this approach. The results are verified with experimental data.     

Bifurcation and resonance in a fractional Mathieu-Duffing oscillator

The bifurcation and resonance phenomena are investigated in a fractional Mathieu-Duffing oscillator which contains a fast parametric excitation and a slow external excitation. We extend the method of direct partition of motions to evaluate the response for the parametrically excited system. Besides, we propose a numerical method to simulate different types of local bifurcation of the equilibria. For the nonlinear dynamical behaviors of the considered system, the linear stiffness coefficient is a key factor which influences the resonance phenomenon directly. Moreover, the fractional-order damping brings some new results that are different from the corresponding results in the ordinary Mathieu-Duffing oscillator. Especially, the resonance pattern, the resonance frequency and the resonance magnitude depend on the value of the fractional-order closely.