Preparation of ZnO–Al2O3 Particles in a Premixed Flame

Zinc oxide (ZnO) and alumina (Al₂O₃) particles are synthesized by the combustion of their volatilized acetylacetonate precursors in a premixed air–methane flame reactor. The particles are characterized by XRD, transmission electron microscopy, scanning mobility particle sizing and by measurement of the BET specific surface area. Pure (-)alumina particles appear as dendritic aggregates with average mobile diameter 43–93 nm consisting of partly sintered, crystalline primary particles with diameter 7.1–8.8 nm and specific surface area 184–229 m²/g. Pure zinc oxide yields compact, crystalline particles with diameter 25–40 nm and specific surface area 27–43 m²/g. The crystallite size for both oxides, estimated from the XRD line broadening, is comparable to or slightly smaller than the primary particle diameter. The specific surface area increases and the primary particle size decreases with a decreasing flame temperature and a decreasing precursor vapour pressure. The combustion of precursor mixtures leads to composite particles consisting of zinc aluminate ZnAl₂O₄ intermixed with either ZnO or Al₂O₃ phases. The zinc aluminate particles are dendritic aggregates, resembling the alumina particles, and are evidently synthesized to the full extent allowed by the overall precursor composition. The addition of even small amounts of alumina to ZnO increases the specific surface area of the composites significantly, for example, zinc aluminate particles increases to approximately 150 m²/g. The gas-to-particle conversion is initiated by the fast nucleation of Al₂O₃ or ZnAl₂O₃, succeeded by a more gradual condensation of the excess ZnO with a rate probably controlled by the cooling rate for the flame.     

Effect of ZnAl2O4 coating on the compressive behaviors of aluminum borate whiskers-reinforced aluminum composites at elevated temperatures

Aluminum borate whiskers (ABOw) with or without ZnAl₂O₄ coating reinforced pure aluminum composites (ABOw/Al, ABOw/ZnAl₂O₄/Al) were fabricated by squeeze casting. The effects of ZnAl₂O₄ coating on the compressive behaviors, microstructures, and matrix textures of the composites were investigated at different temperatures and strain rates. The results indicate that the maximum compressive flow stress of the composites almost linearly decreases with the increase in temperature. The maximum compressive flow stress of ABOw/ZnAl₂O₄/Al composite is higher than that of ABOw/Al composite at the same temperature when the strain rate is larger, however, it is reversed when the strain rate is smaller. It is more serious for the fracture of whiskers in ABOw/ZnAl₂O₄/Al composite than that in ABOw/Al composite at the high compressive strain rate. However, the average length of whiskers in ABOw/ZnAl₂O₄/Al composite is larger than that in ABOw/Al composite at the low compressive strain rate. The strong matrix texture in ABOw/ZnAl₂O₄/Al composite appears at the high compressive strain rate, however, it is observed in ABOw/Al composite at the low compressive strain rate.     

Effect of heat treatment on the structure and morphology of ZnO nanorod array and its composite with titania precursor

ABSTRACT

Effects of the elevated temperature on the structure evolution of the ZnO nanorod array (ZNA) and their hybrid nanocomposite with layered (tetramethyl)ammonium titanate (LTMAT) prepared by the liquid phase deposition were investigated. The vertically oriented ZnO nanorods were deposited on a quartz plate by a chemical bath deposition method and then they were penetrated by the LTMAT using the dip-coating method from the water solution. As a result of such an experimental procedure, an assembly composed of the ZNA with LTMAT was obtained and called hybrid nanocomposite. Since the LTMAT converts to TiO₂ upon subsequent sintering at 350 °C, it can be regarded as TiO₂ precursor for the thermal treatment experiments. The experiments with ZNA and their hybrid nanocomposite at the elevated temperature revealed coalescence of the deposited ZnO nanorods and crystallization of zinc titanate with Zn₂TiO₄ stoichiometry.     

Zinc oxide nanostructures for applications as ethanol sensors and dye-sensitized solar cells

ZnO nanostructures were prepared by thermal oxidation technique for applying as ethanol sensors and dye-sensitized solar cells. To improve sensitivity of the sensor based on ZnO nanostructures, gold doping was performed in ZnO nanostructures. Gold-doped with 0%, 5%, and 10% by weight were investigated. The improvement of sensor sensitivity toward ethanol due to gold doping was observed at entire operating temperature and ethanol concentration. The sensitivity up to 145 was obtained for 10% Au-doped ZnO sensor. This can be explained by an increase of the quantity of oxygen ion due to catalytic effect of gold. Also, it was found that oxygen ion species at the surface of the Au-doped ZnO sensor remained O²⁻ as pure ZnO sensor. For dye-sensitized solar cell application, the dye-sensitized solar cell structure based on ZnO as a photoelectrode was FTO/ZnO/Eosin-Y/electrolyte/Pt counter electrode. ZnO with different morphologies of nanobelt, nano-tetrapod, and powder were investigated. It was found that DSSCs with ZnO powder showed higher photocurrent, photovoltage and overall energy conversion efficiencies than that of ZnO nanobelt and ZnO nano-tetrapod. The best results of DSSCs were the short circuit current (J_sc) of 1.25 mA/cm², the open circuit voltage (V_oc) of 0.45 V, the fill factor (FF) of 0.65 and the overall energy conversion efficiency (η) of 0.68%.     

Synthesis of ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> complex substrates and growth of GaN films

With the solid phase reaction between pulsed-laser-deposited (PLD) ZnO film and α-Al₂O₃ substrate, ZnAl₂O₄/α-Al₂O₃ complex substrates were synthesized. X-ray diffraction (XRD) spectra show that as the reaction proceeds, ZnAl₂O₄ changes from the initial (111)-oriented single crystal to poly-crystal, and then to inadequate (111) orientation. Corresponding scanning electron microscope (SEM) images indicate that the surface morphology of ZnAl₂O₄ transforms from uniform islands to stick structures, and then to bulgy-line structures. In addition, XRD spectra present that ZnAl₂O₄ prepared at low temperature is unstable at the environment of higher temperature. On the as-obtained ZnAl₂O₄/α-Al₂O₃ substrates, GaN films were grown without any nitride buffer using light-radiation heating low-pressure MOCVD (LRH-LP-MOCVD). XRD spectra indicate that GaN film on this kind of complex substrate changes fromc-axis single crystal to poly-crystal as ZnAl₂O₄ layer is thickened. For the single crystal GaN, its full width at half maximum (FWHM) of X-ray rocking curve is 0.4°. Results indicate that islands on thin ZnAl₂O₄ layer can promote nucleation at initial stage of GaN growth, which leads to the (0001)-oriented GaN film.     

Preparation and characterization of NiFe2O4/NiO composite film via a single-source precursor route

NiFe₂O₄/NiO nanocomposite thin films have been successfully prepared through a facile route using nickel iron layered double hydroxide (NiFe-LDH) as a single-source precursor. This synthetic approach mainly involves the formation of NiFe-LDH film by casting the slurry of NiFe-LDH precursor on the α-Al₂O₃ substrate, followed by high-temperature calcination. The composition, microstructure and properties of the films were characterized in detail by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX) and vibrating sample magnetometer (VSM). The results indicate that NiFe₂O₄/NiO composite film was composed of granules with diameter less than 100 nm, and the thickness of the film was in the range 1-2 μm. The magnetization of the film can be tuned by alternating the Ni/Fe molar ratio of LDH precursor. In addition, the method developed should be easily extended to fabricate other MFe₂O₄/MO composite film systems with specific applications just by an appropriate combination of divalent/trivalent composition in the precursor of LDHs.     

Self-organized ZnAl2O4 nanostructures grown on -sapphire

Self-organized ZnAl₂O₄ nanostructures with the appearance (in SEM) of high aspect ratio horizontal nanowires are grown on uncatalysed c-sapphire by vapour phase transport. The nanostructures grow as three equivalent crystallographic variants on c-sapphire. Raman and cathodoluminescence spectroscopy confirm that the nanostructures are not ZnO and TEM shows that they are the cubic spinel, zinc aluminate, ZnAl₂O₄, formed by the reaction of Zn and O with the sapphire substrate.     

Deposition of ZnO Nanocrystals on Fe3O4 Nanocubes and Their Special Luminescent and Magnetic Properties

With increasing miniaturization, it is extremely important to maintain the magnetization stability at small scale. Herein, more efforts and interests focus on the interface of magnetic core and semiconductor shell to obtain desired magnetic and/or luminescent properties. Here, Fe₃O₄ nanocubes are synthesized via a thermal decomposition followed by coating ZnO nanocrystals. To create a large interface, large Fe₃O₄ nanocubes with 78 ± 3 nm average side‐length are synthesized through adjusting the ratio of iron precursor to stabilizer. The average diameter of the particular ZnO nanostructures coated on the nanocubic Fe₃O₄ is around 10 ± 2 nm. In addition to the photoluminescent properties of the ZnO‐coated nanostructures, core‐shell Fe₃O₄@ZnO nanostructures demonstrate enhanced UV absorption at 360 nm, which has a 20 nm blueshift compared to bulk ZnO. The superparamagnetic properties of Fe₃O₄@ZnO core–shell hybrid nanocrystals at room temperature are dominated by the ferromagnetic properties when the temperature is lower than the Blocking temperature, 235.7 K. The observed exchange bias and temperature‐dependent magnetization can result from the interfacial interphase between ZnO and Fe₃O₄. The anisotropy contributed by the interfacial interphase allows the nanostructures to maintain stable magnetization in miniaturized devices.     

Synthesis and characterization of nanostructured Li2MnO3 from nanostructured MnOOH precursors

Li₂MnO₃ with different nanostructures was synthesized through a solid-state reaction. MnOOH nanorods and nanowires prepared via the hydrothermal method were used as precursors, respectively, to react with Li(OH)·H₂O to prepare nanostructured Li₂MnO₃ in the temperature range from 500 to 800 °C. The samples were characterized by XRD, TEM, ESR and FTIR results. Based on the experimental results, the dehydration-oxidation-combination (DOC) formation mechanism of Li₂MnO₃ was proposed.     

ZnO-coated zinc antimonate nanocables

ZnO-coated zinc antimonate (ZnSb₂O₄) nanocables have been fabricated via a simple one-step thermal evaporation of layered powders of Sb₂O₃ and ZnO on a brass substrate. The samples were characterized using X-ray diffraction, scanning electron microscopy and high resolution transmission electron microscopy with a high-angle annular dark-field attachment. The nanocables are several tens of micrometers in length; the ZnSb₂O₄ core is ∼30 nm in diameter and the thickness of the ZnO sheath is ∼5 nm. Both the ZnSb₂O₄ core and the ZnO sheath are single crystalline. The controlled growth mechanism of ZnO-coated ZnSb₂O₄ nanocables was considered to be the combination of oxide-assisted evaporation and vapor–solid processes. PACS 61.46.+w; 81.07.-b     

Epitaxial ZnO films grown on ZnO-buffered c-plane sapphire substrates by hydrothermal method

ZnO films are hydrothermally grown on ZnO-buffered c-plane sapphire substrates at a low temperature of 70 °C. A radio-frequency (RF) reactive magnetron sputtering has been used to grow the ZnO buffer layers. X-ray diffraction, scanning electron microscopy, and room temperature photoluminescence are carried out to characterize the structure, morphology and optical property of the films. It is found that the films are stress-free. The epitaxial relationship between the ZnO film and the c-plane sapphire substrate is found to be ZnO (0 0 0 1)||Al₂O₃ (0 0 0 1) in the surface normal and in plane. Sapphire treatment, as such acid etching, nitridation, and oxidation are found to influence the nucleation of the film growth, and the buffer layers determine the crystalline quality of the ZnO films. The maximum PL quantum efficiency of ZnO films grown with hydrothermal method is found to be about 80% of single-crystal ZnO.     

Photoluminescence, FTIR and X-ray diffraction studies on undoped and Al-doped ZnO thin films grown on polycrystalline α-alumina substrates by ultrasonic spray pyrolysis

Undoped and aluminum-doped zinc oxide (ZnO) thin films have been grown on polycrystalline α-alumina substrates by ultrasonic spray pyrolysis (USP) technique using zinc acetate dihydrate and aluminum chloride hexahydrate (Al source) dissolved in methanol, ethanol and deionized water. A number of techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and photoluminescence (PL) were used to characterize the obtained ZnO thin films. It was seen that the orientation changed with increase in substrate temperature. During the ZnO deposition Zn source reacted with polycrystalline α-Al₂O₃ substrate to form an intermediate ZnAl₂O₄ spinel layer. It has been interestingly found that the intensity of green emission at 2.48 eV remarkably increased when the obtained ZnO:Al films were deposited at 380 °C. The FTIR absorbance intensity of spectroscopic band at 447±6 cm⁻¹ is very sensitive to oxygen sublattice disorder resulting from non-stoichiometry, which is consistent with the result of PL characterization.     

Chemical spray pyrolysis deposition and characterization of p-type CuCr1−xMgxO2 transparent oxide semiconductor thin films

A chemical spray pyrolysis technique for deposition of p-type Mg-doped CuCrO₂ transparent oxide semiconductor thin films using metaloorganic precursors is described. As-deposited films contain mixed spinel CuCr₂O₄ and delafossite CuCrO₂ structural phases. Reduction in spinel CuCr₂O₄ fraction and formation of highly crystalline films with single phase delafossite CuCrO₂ structure is realized by annealing at temperatures ?700 °C in argon. A mechanism of synthesis of CuCrO₂ films involving precursor decomposition, oxidation and reaction between constituent oxides in the spray deposition process is presented. Post-annealed CuCr_0.93Mg_0.07O₂ thin films show high (?80%) visible transmittance and sharp absorption at band gap energy with direct and indirect optical band gaps 3.11 and 2.58 eV, respectively. Lower (∼450 °C) substrate temperature formed films are amorphous and yield lower direct (2.96 eV) and indirect (2.23 eV) band gaps after crystallization. Electrical conductivity of CuCr_0.93 Mg_0.07O₂ thin films ranged 0.6-1 S cm⁻¹ and hole concentration ∼2×10¹⁹ cm⁻³ determined from Seebeck analysis. Temperature dependence of conductivity exhibit activation energies ∼0.11 eV in 300-470 K and ∼0.23 eV in ?470 K region ascribed to activated conduction and grain boundary trap assisted conduction, respectively. Heterojunction diodes of the structure Au/n-(ZnO)/p-(CuCr_0.93Mg_0.07O₂)/SnO₂ (TCO) were fabricated which show potential for transparent wide band gap junction device.     

Cathodoluminescence characterization of ZnO:Te microstructures obtained with ZnTe and TeO2 doping precursors

ZnTe- and TeO₂-doped ZnO nanostructures and microstructures were obtained by a vapour–solid process by sintering compacted ZnO powder mixed with each precursor. Cathodoluminescence (CL) measurements show that if TeO₂ is used, then the defect band, due mainly to O vacancies (V _O), tends to reduce and even disapear, which indicates that Te reacts with ZnO and passivates the O vacancies better than if ZnTe is used as a precursor. With both precursors, a CL peak at about 3.08–3.17 eV, which overlaps with that of ZnO at about 3.26 eV, indicates that ZnTe_xO_1−x forms.     

Shape-controlled synthesis of CuS nanocrystallites via a facile hydrothermal route

Without the use of any extra surfactant, template or other additive, shape-controlled synthesis of sphere-, urchin- and tube-like CuS nanocrystallites has been realized just via hydrothermal treatment of different amounts of CuSO₄·5H₂O and equimolar Na₂S₂O₃·5H₂O in water at 150 °C for 12 h. The possible mechanism for the formation of the various nanostructures of CuS in this system was discussed.     

Rational synthesis of α-MnO2 and γ-Mn2O3 nanowires with the electrochemical characterization of α-MnO2 nanowires for supercapacitor

An acidification-hydrothermal method was developed to synthesize α-MnO₂ nanowires, which was subsequently treated with ethanol, resulting in γ-Mn₂O₃ nanowire bundles on a large scale. The electrochemical characterization was carried out by cyclic voltammetry, which indicated that the α-MnO₂ nanowires in 0.5 mol L⁻¹ Na₂SO₄ aqueous electrolyte was of an excellent electrode material for supercapacitor at the scan rate of 10 mV S⁻¹ in the range of 0.0-0.85 V.     

Synthesis of ZnFe2O4 nanocrystallites by mechanochemical reaction

Mechanochemical reaction of ZnO and α-Fe₂O₃ in a planetary mill formed an amorphous precursor, which was subsequently heated to successfully produce zinc ferrite (ZnFe₂O₄) nanocrystallites. The amorphous precursor and nanocrystallites were characterized by differential thermal analysis (DTA), thermogravimetric analysis (TGA), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Calcination of the precursor powder at 600 °C led to the formation of ZnFe₂O₄ nanocrystallites of about 22 nm in crystal size, and most of particle was about 10-50 nm in diameter. Effect of calcination temperature on the crystal size of the nanoparticles was investigated. The mechanism of nanocrystallite growth was primarily investigated. The activation energy of ZnFe₂O₄ nanocrystallite formation during thermal treatment was calculated to be 18.5 kJ/mol.     

TSL, OSL and ESR studies in ZnAl2O4:Tb phosphor

ZnAl₂O₄:Tb phosphor was prepared by combustion synthesis. ZnAl₂O₄:Tb exhibits three thermally stimulated luminescence (TSL) peaks around 150, 275 and 350 °C. ZnAl₂O₄:Tb exhibits optically stimulated luminescence (OSL) when stimulated with 470 nm light.Electron spin resonance (ESR) studies were carried out to identify defect centres responsible for TSL peaks observed in ZnAl₂O₄:Tb. Two defect centres are identified in irradiated ZnAl₂O₄:Tb phosphor and these centres are assigned to V and F⁺ centres. V centre appears to correlate with the 150 °C TSL peak, while F⁺ centre could not be associated with the observed TSL peaks.     

First-principles study of the structural,mechanical and electronic properties of ZnX2O4（X=Al,Cr and Ga）

This paper performs first-principles calculations to study the structural,mechanical and electronic properties of the spinels ZnAl2O4 ,ZnGa2O4 and ZnCr2O4 ,using density functional theory with the plane-wave pseudopotential method. Our calculations are in good agreement with previous theoretical calculations and the available experimental data. The studies in this paper focus on the evolution of the mechanical properties of ZnAl2O4 ,ZnGa2O4 and ZnCr2O4 under hydrostatic pressure. The results show that the cubic phases of ZnAl2O4 ,ZnGa2O4 and ZnCr2O4 become unstable at about 50 GPa,40 GPa and 25 GPa,respectively. From analysis of the band structure of the three compounds at equilibrium volume,it obtains a direct band gap of 4.35 eV for ZnAl2O4 and 0.89 eV for ZnCr2O4 ,while ZnGa2O4 has an indirect band gap of 2.73 eV.     

An optimal low-temperature tartrate precursor method for the synthesis of monophasic nanosized ZnFe2O4

In this study, the synthesis of monophasic nanocrystalline zinc ferrite (ZnFe₂O₄) was achieved by controlling the thermal decomposition conditions of a zinc–iron tartrate precursor method. Differential thermal analysis/thermogravimetry (DTA/TG), X-ray diffraction (XRD), Fe²⁺ content analysis, transmission electron microscopy (TEM), and Brunauer-Emmett-Teller (BET) techniques were used to investigate the effect of heat treatment conditions on the calcined powders. The thermal decomposition of the precursor led to an intermediate phase formation of ZnO, Fe₃O₄, and γ-Fe₂O₃. It was found that the Fe₃O₄ → γ-Fe₂O₃ oxidation reaction is the key step in producing monophasic nanosized ZnFe₂O₄. The monophasic nanoparticles of ZnFe₂O₄ can be obtained when the precursor is heat treated under a low temperature (300–400 °C) and long residence time (4 h) process that can prompt the Fe₃O₄ oxidation and prevent the formation of α-Fe₂O₃.