Phase Behavior and Thermal Properties for Binary Blends of Bacterial Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s with Narrow‐Comonomer‐Unit Compositional Distribution

The miscibility and the effect of compositional distribution on physical properties were investigated for binary blends of biosynthesized poly(3‐hydroxybutyrate) [P(3HB)] and comonomer compositionally fractionated poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s [P(3HB‐co‐3HH)] with narrow compositional distribution. Biosynthesized P(3HB‐co‐3HH) samples were compositionally fractionated using solvent (chloroform)/nonsolvent (n‐heptane) mixtures. The binary blends of fractionated P(3HB‐co‐3HH)s with different 3HH unit content were prepared by casting from solution in chloroform. The miscibility and the thermal properties of these blends were analyzed by differential scanning calorimetry (DSC). It was found that the two components are miscible in the amorphous phase when the difference in 3HH unit content between the two component polymers of these blends is less than 20 mol‐%, subsequently they are immiscible when the difference is larger than 30 mol‐%. By comparing the thermal properties of the binary blends of fractions, with those for the fractions themselves, and with those for the bacterially as‐produced unfractionated copolyesters, the effects of compositional distribution on the properties of copolyesters were discussed.

Glass transition temperatures of blends PHB/H10, H10/H20, and PHB/H20 versus total 3HH unit content in the blends. The solid lines are the best fits of the experimental results of the P(3HB‐co‐3HH) fractions with narrow compositional distribution.     

Hydrogen‐Bonding Interaction and Crystalline Morphology in the Binary Blends of Poly(ε‐caprolactone) and Polyphenol Catechin

The specific intermolecular hydrogen‐bonding interaction between the ester carbonyl groups of poly(ε‐caprolactone) (PCL) and the phenolic hydroxyl groups of catechin has been studied by Fourier‐transform infrared spectroscopy (FT‐IR) and differential scanning calorimetry (DSC). According to quantitative curve‐fitting analysis of the FT‐IR spectra of PCL/catechin blends, it was found that the fraction of hydrogen‐bonded carbonyl groups of PCL increased with catechin content, while that of hydrogen‐bonded hydroxyl groups of catechin decreased. The calculated crystallinity of PCL in the binary blends, based on the curve‐fitting results, suggested that the crystallization of PCL was restrained in the blends with catechin. Only single glass transition temperature, T_g, was observed over the whole range of blend compositions, which was between those of the pure components. The melting point, T_m, depressed and T_g increased, indicating also the existence of strong intermolecular association. The blend composition dependence of T_g could be predicted very well by the Kwei equation with a positive ‘q’ value of 124. With the aid of small angle X‐ray scattering measurement, the segregation of catechin was investigated. It was found that the extent of extra‐lamellar segregation increased with catechin content. It was suggested that the crystal growth rate played the dominant role in the formation of morphology. With decreasing crystal growth rate of PCL component in the blends, enough time has been given to catechin molecules to diffuse into extra‐lamellar region.

     

Effect of Comonomer‐Unit Compositional Distribution on Thermal and Crystallization Behavior of Bacterial Poly[(3‐hydroxybutyrate)‐co‐(3‐mercaptopropionate)]

The physical properties of novel sulfur‐containing biopolymers, poly[(3‐hydroxybutyrate)‐co‐(3‐mercaptopropionate)]s [P(3HB‐co‐3MP)s], have been investigated in detail by¹H and ¹³C NMR spectroscopy, wide‐angle X‐ray diffraction (WAXD) analysis, DSC, and FT‐IR spectroscopy. Based on a solvent/non‐solvent (chloroform/heptane) fractionation method, an original P(3HB‐co‐3MP) sample with 3MP unit content of 16.3 mol‐% was fractionated into eight fractions with 3MP unit content ranging from 10.3 to 37.2 mol‐% and number‐average molecular weight from 0.4 × 10⁵ to 2.9 × 10⁵. The thermal and crystallization behavior were found to be greatly affected by the comonomer‐unit composition and its distribution. Furthermore, the 3MP comonomer unit was found to be included in the crystalline phase in some fractions.

     

Synthesis and Characterization of Novel Biodegradable Copolymers of 5‐Benzyloxy‐1,3‐dioxan‐2‐one and Glycolide

A series of novel biodegradable random copolymers of 5‐benzyloxy‐1,3‐dioxan‐2‐one (5‐benzyloxy‐trimethylene carbonate, BTMC) and glycolide were synthesized by ring‐opening polymerization. The copolymers were characterized by nuclear magnetic resonance (NMR) spectroscopy and gel permeation chromatography (GPC). The incorporation of BTMC units into the copolymer chains results in good solubility of the polymers in common solvents. The in vitro degradation rate can be tailored by adjusting the composition of the copolymers.

The in vitro degradation of the homopolymers and poly(BTMC‐co‐GA) copolymers.     

Preparation of Highly Transparent and Thermally Stable Films of α‐Cyclodextrin/Polymer Inclusion Complexes

Films of an α‐cyclodextrin/poly(ε‐caprolactone) inclusion complex have been successfully prepared and show high transparency and heat resistance in comparison to the pure polymer film. The physical properties, such as transparency, mechanical properties, and thermal stability, of the α‐CD‐PCL‐IC films are found to depend on the α‐cyclodextrin‐to‐polymer stoichiometry.

     

Novel Spectrally Stable Saturated Blue‐Light‐Emitting Poly[(fluorene)‐co‐(dioctyldibenzothiophene‐S,S‐dioxide)]s

Novel poly[(fluorene)‐co‐(2,8‐dioctyldibenzothiophene‐S,S‐dioxide‐3,7‐diyl)]s were synthesized. The octyl group on the 2,8‐dioctyldibenzothiophene‐S,S‐dioxide (DOSO) unit improved the solubility of the polymers and broadened the optical band gap from 2.95 to 3.20 eV as the content of DOSO unit increases. The electroluminescence (EL) spectra of polymers show CIE coordinates around (0.16, 0.07) independent of the ratio of DOSO units in the polymers, owing to the ICT and steric hindrance dual‐function. A high efficiency of 3.1 cd · A⁻¹ (EQE = 3.9%) was obtained with the configuration of ITO/PEDOT:PSS/polymer/Ba/Al. The results indicate that PF‐3,7DOSOs could be a promising candidate for saturated blue‐emitting polymers with spectral stability and high efficiency.

     

Functionalization of Multi‐Walled Carbon Nanotubes by Thermo‐Grafting with α‐Methylstyrene‐Containing Copolymers

The present article reports on a strategy for the functionalization of multi‐walled carbon nanotubes (MWCNTs) by grafting with various polymer chains. Copolymers consisting of α‐methylstyrene (AMS) and a second monomer, that is glycidyl methacrylate (GMA) or styrene (St), were synthesized in advance. The copolymers were heated in the presence of MWCNTs in solution, decomposition of the AMS sequences occurred, providing macroradicals, which further attacked the double bonds on the MWCNT surfaces. Grafting of the copolymer chains onto the surface of the MWCNTs was thus achieved, as demonstrated by FT‐IR, XPS and Raman technologies. The resulting poly(AMS‐co‐GMA)‐g‐MWCNTs could be uniformly dispersed in N,N‐dimethylformamide (DMF) and acetone, and the poly(AMS‐co‐St)‐g‐MWCNTs also could be uniformly dispersed in DMF.

     

Phase Transition Behaviors of Self‐Oscillating Polymer and Nano‐Gel Particles

Summary: Self‐oscillating polymers and nano‐gel particles consisting of N‐isopropylacrylamide and the ruthenium catalyst of the Belousov‐Zhabotinsky reaction have been prepared. In order to clarify the crosslinking effect on the self‐oscillating behavior, the phase transition behaviors were investigated by measuring the transmittance and the fluorescence intensity of the polymer solution and the gel bead suspension. Cooperative effects due to crosslinking will play an important role for the design of nanoactuators.

Chemical structure of poly(NIPAAm‐co‐Ru(bpy)₃).     

Enzyme‐Catalyzed Ring‐Opening Polymerization of Unsubstituted β‐Lactam

The synthesis of poly(β‐alanine) by Candida antarctica lipase B immobilized as novozyme 435 catalyzed ring‐opening of 2‐azetidinone is reported. After removal of cyclic side products and low molecular weight species pure linear poly(β‐alanine) is obtained. The formation of the polymer is confirmed with ¹H NMR spectroscopy and MALDI‐TOF mass spectrometry. The average degree of polymerization of the obtained polymer is limited to = 8 by its solubility in the reaction medium. Control experiments with β‐alanine as a substrate confirmed that the ring structure of the 2‐azetidinone is necessary to obtain the polymer.

     

Highly Fluorescent Conjugated Copolymers Containing Dithieno[3,2‐b:2′,3′‐d]pyrrole

Three copolymers that incorporate dithieno[3,2‐b:2′,3′‐d]pyrrole with fluorene, carbazole, or pyridine have been prepared by Suzuki reaction and characterized by NMR spectroscopy and GPC. A new homopolymer of dithieno[3,2‐b:2′,3′‐d]pyrrole was also synthesized for the comparison of their structure–property relationships. Their thermal, optical, and electrochemical properties have been investigated. All the polymers exhibit good thermal stability with decomposition temperatures around 400 °C. The fluorescence quantum efficiencies of all these polymers in solution are in the range of 33.5–55.5%. The copolymers also show high film fluorescence quantum efficiencies of about 20% while the fluorescence of the homopolymer film is almost quenched.

     

η3‐Benzyl‐Nickel‐Diimine Complex: Synthesis and Catalytic Properties in Ethylene Polymerization

The oxidative addition of benzyl chloride to Ni(cod)₂ in the presence of 1,4‐bis(2,6‐diisopropylphenyl)acenaphthenediimine followed by chloride abstraction affords [(η³‐CH₂C₆H₅)Ni(α‐diimine)][PF₆] (α‐diimine = 1,4‐bis(2,6‐diisopropylphenyl)acenaphthenediimine) in 70% yield. The complex is active in ethylene polymerization in the presence of methylaluminoxane and under mild reaction conditions. The polyethylenes obtained are highly branched, have very low densities, do not show T_m or measurable crystallinity and have molecular weights ranging from 80 × 10³ to 290 × 10³ g · mol⁻¹.

     

Synthesis and Characterization of a Block Copolymer Containing Regioregular Poly(3‐hexylthiophene) and Poly(γ‐benzyl‐L‐glutamate)

Poly(3‐hexylthiophene)‐b‐poly(γ‐benzyl‐L ‐glutamate) (P3HT‐b‐PBLG) rod–rod diblock copolymer was synthesized by a ring‐opening polymerization of γ‐benzyl‐L ‐glutamate‐N‐carboxyanhydride using a benzylamine‐terminated regioregular P3HT macroinitiator. The opto‐electronic properties of the diblock copolymer have been investigated. The P3HT precursor and the P3HT‐b‐PBLG have similar UV–Vis spectra both in solution and solid state, indicating that the presence of PBLG block does not decrease the effective conjugation length of the semiconducting polythiophene segment. The copolymer displays solvatochromic behavior in THF/water mixtures. The morphology of the diblock copolymer depends upon the solvent used for film casting and annealing results in morphological changes for both films deposited from chloroform and trichlorobenzene.

     

Effect of Microstructures on the Phase Transition Behavior of P(CL‐GL)‐PEG‐P(CL‐GL) Triblock Copolymer Aqueous Solutions

Amphiphilic poly[(ε‐caprolactone)‐co‐glycolide]‐block‐poly(ethylene glycol)‐block‐poly[(ε‐caprolactone)‐co‐glycolide) [P(CL‐GL)‐PEG‐P(CL‐GL)] triblock copolymers with different average lengths of caproyl sequences (L_CL) were synthesized by ring‐opening polymerization at different temperatures. A 25% aqueous solution of the copolymer with L_CL = 11.0 formed a gel, owing to strong crystallinity‐induced hydrophobicity at low temperature, and underwent a gel‐sol transition (UCST behavior) when the temperature was increased to 40 °C. In contrast, the solution of copolymer with L_CL = 6.7 underwent a sol‐gel transition (LCST behavior) due to micelle aggregation. However, a clear sol‐turbid sol phase transition was observed for the copolymer with more random microstructures (L_CL = 5.2).

     

A New Crystal Form,Polymorphism, and Multi‐Morphology in Biodegradable Poly(3‐hydroxypropionate)

Summary: A new crystal morphology (δ form) of poly(3‐hydroxypropionate) (PHP) is found in cast and melt‐crystallized PHPs with low molecular weight, in which the PHP chains possibly adopt a 2₁ helix rather than the trans conformation found in the β or γ form. The fusion temperature‐ and the crystallization temperature‐dependent polymorphism are responsible for the dual morphologies and the unique growth kinetics of spherulites in the melt‐crystallized PHPs.

a) A dual‐morphology developed at 70 °C in PHP films after melting at 117 °C and b) that formed during cooling at a rate of 1 °C · min⁻¹ from 130 °C.     

Reaction of Boranes with TMS Diazomethane and Dimethylsulfoxonium Methylide. Synthesis of Poly(methylidene‐co‐TMSmethylidene) Random Copolymers

Summary: Borane reacts with TDM by a sequence of insertion and disproportionation reactions to yield tris‐(trimethylsilylmethyl)borane. No further addition of TDM occurs. Triallylborane and tris‐(4‐methoxyphenylethyl)borane initiate the copolymerization of TDM and dimethylsulfoxonium methylide. The reactions afford TMS‐substituted polymethylene oligomers. The resultant poly(methylidene‐co‐TMSmethylidene) random copolymers arise from incorporation of TMSmethylidene (CHSiMe₃) and methylidene (CH₂) groups into the growing polymer chain one carbon at a time.

Trialkylborane‐catalyzed copolymerization of trimethylsilyl diazomethane and dimethylsulfoxonium methylide.     

3‐Ethylated N‐Vinyl‐2‐pyrrolidone with LCST Properties in Water

The monomer 3‐ethyl‐1‐vinyl‐2‐pyrrolidone ( 3 ) and the homopolymer poly(3‐ethyl‐1‐vinyl‐2‐pyrrolidone) ( 5 ) have been synthesized. Polymer 5 is soluble in water and shows a critical temperature (T_c) of 27 °C. The presence of cyclodextrin causes a slight shift of the T_c. The lower critical solution temperature (LCST) could be varied between 27 and 40 °C by copolymerization with N‐vinyl‐2‐pyrrolidone. A linear correlation between the T_c and the copolymer composition is observed.

     

Novel π‐Electron Extension System via Chromophores Self‐Polymerization to Enhance the NLO Efficiency

A new strategy for the self‐polymerization of chromophores is investigated to develop a 2,7‐carbazole‐based nonlinear optical (NLO) conjugated polymer with an increasing conjugation length of chromophores. Elongation of the conjugation‐path length in chromophores has established engineering guidelines to enhance optical nonlinearity. Compared with the traditional synthesis of an NLO polymer, the chromophores should be well‐designed at a limited conjugation spacer, and then incorporated into a polymer matrix. In this research, the π‐conjugation spacer of chromophores extended perpendicularly to the dipole of chromophores during the polymerization process. Furthermore, this study marks the first research of integrating the π‐electrons of chromophores and conjugated polymers. These conjugated backbones promote a bulk‐polarization response, leading to large NLO coefficients.

     

Structural Characterization and Enzymatic Degradation of α‐, β‐, and γ‐Crystalline Forms for Poly(β‐propiolactone)

A structural comparison of three different crystalline forms of poly(β‐propiolactone) (PPL) was carried out by wide‐angle X‐ray diffraction, Fourier‐transform infrared spectroscopy, and differential scanning calorimetry. The α‐form in a hot‐drawn and annealed film represents a 2₁ helix conformation. The β‐form in a cold‐drawn and annealed film represents a planar zigzag conformation. The γ‐form in an oriented sedimented mat of solution‐grown chain‐folded lamellar crystals also implies a planar zigzag conformation. The solution‐cast film depicts similar outlines with the γ‐form in lamellar crystals in all the experimental measurements, suggesting that the molecular chain in the solution‐cast film has a planar zigzag conformation. While elongation at break decreased, tensile strength and Young's modulus increased with an increase in the crystallinity, independent of the crystalline forms. The influence of the enzymatic degradation of these crystal structures has been investigated by using an extracellular PHB depolymerase purified from Ralstonia pickettii T1. The rate of degradation was in the order of β‐form > α‐form > solution‐cast (γ‐form) film, and the different surface morphologies after partial enzymatic degradation were observed in scanning electron micrographs. It is suggested that the crystal structure is one of the important factors for determining the rate of degradation together with crystallinity.

Enzymatic degradation profiles of poly(β‐propiolactone) films.     

Comonomer Compositional Distribution and Thermal Characteristics of Bacterially Synthesized Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s

The comonomer composition and its distribution have been investigated for poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(3HB‐co‐3HH)], which was bacterially synthesized by Ralstonia eutropha from coconut oil as a carbon source. Using a chloroform/heptane mixed solvent, they were fractionated into several fractions with different comonomer composition. Bacterially synthesized P(3HB‐co‐3HH)s were found to have a wide compositional distribution. Using the fractions with a narrower comonomer composition distribution, the compositional dependence of thermal properties was investigated. The differential scanning calorimetry (DSC) melting behavior of a sample of unfractionated P(3HB‐co‐3HH) did not reflect that of fractions with similar average 3HH content. It was concluded that each of the fractions affects the thermal properties of the original unfractionated P(3HB‐co‐3HH), which should therefore be considered as polymer blends.     

A Closed‐Loop Phase Diagram in a Weakly Interacting Polyolefin Copolymer Binary Blend System

Summary: The phase behavior of poly(ethylene‐co‐styrene) (PES) and poly(ethylene‐co‐butene) (PEB) blends has been studied. A closed‐loop phase diagram was clearly observed in this weakly interacting system as the styrene content in the PES decreased to about 1 mol‐%. At higher styrene contents, the phase loop starts to interplay with the crystallization transformation at lower temperatures.

Phase diagram of PEB/PES blends. Phase boundary line is only for easy demonstration.