自由基引发剂强化稠油催化水热裂解降黏行为

本文考察了自由基引发剂对胜利油田单56区块稠油样品催化水热裂解反应过程的协同强化作用.在反应温度为220℃,添加0.2 wt%的引发剂——过氧化二叔丁基,使水热裂解后的降黏率由不加引发剂时的61.4%升高到72.7%.此外,在引发剂存在、150℃条件下,降黏率可达到69.0%,表明引发剂的加入可显著提高较低反应温度下的水热裂解效果.对反应前后油样进一步分析发现,反应样品中饱和分、芳香分、胶质和沥青质平均分子量均下降;饱和分、芳香分含量增加,而胶质、沥青质含量下降;胶质、沥青质中氢碳原子比增加,含硫量减少,含氮量变化不大;表明重质组分在水热裂解过程中发生了裂解反应、尤其是含硫官能团在水热裂解中发生了反应;反应样品沥青质及胶质芳香环系的缩合程度降低.实验结果表明,反应过程中稠油重质组分发生了裂解,而且胶质的裂解程度更大,轻质组分含量增加,导致稠油黏度降低、流动性提高,在一定程度上改善了稠油的品质;引发剂可以在较低温度下产生自由基,从而使水热裂解反应在较低反应温度下有效进行.     

重度原油注空气低温氧化过程研究(英文)

低温氧化反应对现场燃烧(ISC)技术点火的成功有十分重要的影响.采用高压氧化管,研究了不同温度压力下,新疆克拉玛依重度原油的低温氧化过程.结果表明,温度和压力的变化对低温氧化反应的放热程度、持续时间以及气体产物有明显影响.适合油样低温氧化反应的温度和压力分别为150℃和10MPa.此外,采用纯组分替代原油族组分进行低温氧化实验,研究低温氧化反应对原油族组分(饱和烃、芳香烃、胶质、沥青质)含量的影响.结果表明,原油所含族组分中,芳香烃组分最易被氧化,其含量由氧化前的19.17%减少到12.38%(150℃)和9.51%(250℃).随着低温氧化过程的进行,结构复杂的族组分(胶质、沥青质)的含量明显增加.实验数据对油藏实施注空气技术,以及该技术现场实施条件的确定有十分重要的指导意义.     

Pingba RP-3喷气燃料中有色组分的鉴定及其特性研究

用中性氧化铝吸附、无水乙酸脱附的方法，对储存中变色的Pingba RP-3喷气燃料中的有色组分进行分离制备。应用有机元素分析、红外光谱、色质联用和裂解色质联用等分析法对富集有色组分的吸附胶质进行了分析鉴定，对燃料的储存特性和有色组分的化学特性进行了考察。结果表明，Pingba RP-3喷气燃料中的有色组分全部集中在吸附胶质中，吸附胶质以含氧化合物为主，其主要成分为烷基苯酚类（及其多聚体）化合物，含氮化合物质量分数极少，未检出含硫化合物。Pingba RP-3在储存中颜色变深的主要原因是胶质中的烷基苯酚类化合物氧化和缩聚。储存过程中喷气燃料的吸附胶质和颜色增加显著，与燃料在一定条件下的氧化反应有关。     

超声波处理对加氢反应前后沥青质单元分子结构的影响

以胜利减渣和沙轻减渣为原料,研究了超声波处理对加氢反应前后沥青质单元分子结构的影响,并结合1H-NMR数据、沥青质单元分子参数变化和红外光谱分析等结果,用Chem Bio Draw Ultra 2012模拟出不同条件下两种沥青质单元分子的结构。结果表明,超声波处理减少了沥青质的缔合数,使沥青质单元分子发生开环反应和脱烷基侧链反应加剧,改变了沥青质单元分子的结构,对加氢后沥青质单元分子的结构和组成产生重要影响。沥青质单元分子模型可形象体现超声波处理对加氢反应前后沥青质单元分子化学结构的影响,有助于在分子水平上解释超声波处理影响沥青质单元分子的原因。     

委内瑞拉常压渣油供氢热转化研究

采用高压釜研究了委内瑞拉常压渣油的常规减黏裂化与供氢热转化过程。结果表明,相比常规减黏裂化而言,供氢热转化过程中的供氢剂能够抑制气体产物、沥青质以及焦的形成,后者的气体收率比前者低0.5%~1.2%,生焦率低0.02%~0.98%,残渣油沥青质含量低0.6%~1.3%;在反应温度425℃、反应时间5~20 min条件下,供氢热转化过程的总降黏率、净降黏率变化分别为46.1%~54.8%、10.2%~33.0%;供氢热转化过程的较佳反应条件为425℃、5 min,此条件下供氢热转化生成油斑点实验等级为一级(ASTM D4740),运动黏度(50℃)为185.5 mm²/s,净降黏率为26.4%,满足了船运的基本要求。     

自由基引发剂用于渣油减黏裂化的研究

基于热裂化按照自由基反应机理进行的特点,在高压釜式反应器中分别添加四种自由基引发剂偶氮二异丁腈(AIBN)、过氧化特二丁基(DTBP)、单质硫(S)和单质碘(I2),考察引发剂在390℃～410℃,引发剂添加量0～3000×10-6条件下对三种减压渣油减黏裂化的影响。通过测定减黏前后渣油的运动黏度和四组分的变化,对引发剂的作用机理进行了初步研究。结果表明,自由基引发剂对不同基属的减压渣油减黏裂化反应均有明显的促进作用,大小依次为:LHVR≥GDVRDQVR,并且这种促进作用在较低的反应温度下更加明显,促进效果由渣油本身的物理化学性质所决定。在同等条件下,I2和S促进渣油减黏的效果是AIBN和DTBP降黏率的两倍,这与S和I2形成氢化物的"活性原子"可以多次循环发生作用有关。与S相比,单质I2减黏促进作用更为明显。     

胜利超稠油的乳化降黏机理研究

研究了胜利油田滨南超稠油单56-4X4高黏的内在原因。油品性质分析结果表明,影响其高黏度的主要因素有两个:胶质、沥青质的总含量超过30%;有机杂原子O、N、S及过渡金属Ni等形成的配位络合物增加了沥青质分子的内聚力。实验筛选出的降黏剂OP-10对该超稠油降黏率高达99.59%。通过FT-IR、SEM、分子量和偶极矩等分析对比了降黏剂作用前后胶质、沥青质的结构性质变化,结果表明,OP-10使胶质、沥青质的氢键缔合作用减弱,部分拆散沥青质的堆积结构,从而使胶质、沥青质的分子量和偶极矩减小,分析得到降黏剂分子能渗透及分散胶质、沥青质的堆砌聚集体。偏光显微镜对乳状液及蜡晶微观形态的分析表明,降黏剂OP-10使超稠油乳状液由W/O型反相为O/W型而起到降黏作用;使蜡晶的聚集形态由细小均匀转变为尺寸较大的絮凝体,破坏蜡晶的三维网络结构,促进稠油黏度的下降。     

超声波处理对加氢反应前后沥青质单元分子结构的影响

以胜利减渣和沙轻减渣为原料,研究了超声波处理对加氢反应前后沥青质单元分子结构的影响,并结合¹H-NMR数据、沥青质单元分子参数变化和红外光谱分析等结果,用Chem Bio Draw Ultra 2012模拟出不同条件下两种沥青质单元分子的结构。结果表明,超声波处理减少了沥青质的缔合数,使沥青质单元分子发生开环反应和脱烷基侧链反应加剧,改变了沥青质单元分子的结构,对加氢后沥青质单元分子的结构和组成产生重要影响。沥青质单元分子模型可形象体现超声波处理对加氢反应前后沥青质单元分子化学结构的影响,有助于在分子水平上解释超声波处理影响沥青质单元分子的原因。     

渣油热反应体系中第二液相的形成机制

在渣油热反应体系中，随着热处理时间的延长，用光学显微镜从渣油反应样品中依次观察到了片状／不规则状物理第二液相，少数圆球状化学物理第二液相和大量不规则状化学第二液相。对第二液相相分离点时渣油热反应体系物理化学状态的考察指出：物理第二液相是渣油原始体系中的沥青质胶质重组分混合胶团破坏后，丧失胶质组分保护的原生沥青质组分通过物理聚集过程形成的，其形貌特征源于原生沥青质组分的分形聚集过程和热力学成长过程；在化学物理第二液相相分离点，丧失胶质组分保护的原生沥青质发生分子内桥键和脂肪侧链断裂，形成平面性较高的稠环芳香性分子，它们在适宜的体系流动性条件下经有序聚集成长为具有最低能量构型的球形态；随着反应程度加深，原生沥青质特别是原生胶质的自由基反应经诱导期后速度剧增，导致体系中在短时间内产生大量次生沥青质，它们经由动力学成长形成不规则状化学第二液相。     

六甲氧基甲基三聚氰胺-多元醇-丙烯酸酯混杂聚合过程热互补效应的研究

六甲氧基甲基三聚氰胺（HMMM）－多元醇－丙烯酸酯－酸催化剂的混合体系在较高温度下同时进行缩聚和自由基聚合并表现出协同效应，DSC研究结果表明，丙烯酸酯在HMMM和酸的催化作用下可在较低温度下发生自由基聚合反应，并把反应释放出来的大量的热量有效地传递给缩聚发反应，满足缩聚反应吸热的要求，从而节省固化所需要的能量，为了提高储存稳定性。本文以潜酸催化剂作为酸的来源，对该混杂聚合体系进行了研究，仍有明显的热互补效应。     

Effect of Crude Oil Aging on Asphaltene Inhibitor Product Recommendation

Aging refers to the deterioration of hydrocarbon fluids that manifests as changes in the physicochemical characteristics of the fluid upon exposure to ambient conditions. In order to understand the effect of aging of crude oils on asphaltene inhibitor product recommendation, simulated aging studies were performed on a crude oil from Wyoming with known asphaltene issues. The results clearly show that aging of crude oil affects the stability of the oil with respect to asphaltenes and caution must be exercised when recommending asphaltene inhibitor if the evaluations were performed on fluids after long-term storage. A real case study where ambient storage in the lab adversely affects the stability of the crude oil and renders asphaltene inhibitor ineffective further confirms results from simulated aging.     

溶剂特性对淖毛湖煤加氢液化中间产物反应行为的影响

为探究溶剂特性对煤加氢液化中间产物反应行为的影响,以新疆淖毛湖煤作为原料,四氢萘、循环溶剂及十氢萘作为供氢溶剂,在高压搅拌釜中进行直接加氢液化实验,并运用电子顺磁共振手段分析了中间产物-沥青质的自由基浓度的变化。结果表明,四氢萘溶剂中沥青质随反应温度的升高在大量生成的同时又被转化,产率从290℃的12.92%到350℃的最大34.13%再到430℃的15.98%;循环溶剂中沥青质产率先持续上升,290℃即有31.89%,400℃达到最大47.96%,之后由于结焦反应降低至33.90%。十氢萘溶剂中沥青质产率变化趋势与四氢萘一致。三种溶剂中沥青质自由基浓度的变化趋势相同,均在350℃达到最大值,分别是1.778×10¹⁸、2.323×10¹⁸和1.930×10¹⁸/g,整体上看循环溶剂数值要高于四氢萘,十氢萘介于两者之间。而四氢萘及循环溶剂中沥青质的g值在2.00323-2.00403,变化趋势与液化气体产物中CO_x含量变化相吻合。     

13C核磁共振研究磺化脲醛树脂的反应机理

利用^13CNMR数据证实了在低磺化剂用量下脲醛树脂的磺化改性仍可发生,并对磺化脲醛（SUF）树脂制备过程中的羟甲基化、缩合、磺化及缩聚等各步反应机理进行了探讨.明确了SUF树脂的^13CNMR谱图中各峰位所对应的结构单元,认为3个未知峰的出现与磺化改性得到的一些新结构单元有关,并对它们的结构进行了推测.通过对比不同磺化和缩聚反应程度下得到的SUF产物的^13CNMR数据,对磺化和缩聚反应后某些结构的出现和消失进行了解释.     

Multivariate Screening Analysis of Water-in-Oil Emulsions in High External Electric Fields as Studied by Means of Dielectric Time Domain Spectroscopy

The effect of crude oil resins with various polar characters on the stability of w/o model emulsions containing asphaltenes is investigated using a mixture design. The resins were extracted using an adsorption-desorption technique. One asphaltene fraction and four different resin fractions from one European crude oil were used. The stabilities are measured using time-domain dielectric spectroscopy in high external electric field. It is found that resins with different polar character have different effects on the emulsion stability. At asphaltene/resin ratios of 1 and 5 : 3 the resins in some cases lead to an emulsion stability higher than that of a similar emulsion stabilized by asphaltenes only, while at low asphaltene/resin ratios ( approximately 1 : 3) the emulsion stability is reduced by the resins. The effect on emulsion stability of combining two different resin fractions depended on the resin types combined as well as the relative amount of resins and asphaltenes. Also, an increase in the stability of some of the emulsions containing resins and asphaltenes for a period of 50-300 min after the emulsification was observed. This time-dependence of emulsion stability is attributed to the mobility of resins at the oil-water interface and the slow buildup of a stabilizing interfacial film consisting of resins and asphaltenes. Copyright 2000 Academic Press.     

在分散型催化剂下渣油中饱和分和芳香分临氢热反应行为的研

在微型高压釜中研究了克拉玛依常压渣油（KLAR）和辽河减压渣油（LHVR）的饱和分、芳香分在分散型催化剂作用下的临氢热反应行为并计算其动力学参数。结果表明，饱和分与芳香分主要发生裂化反应，生成石脑油与柴油馏分，不会生成甲苯不溶物，极少量的芳香分缩合生成沥青质。在相同的反应苛刻度下，KLAR与LHVR饱和分裂化和缩合产物产率没有明显的差别，而KLAR芳香分的裂化产物产率略高于LHVR芳香分，而其缩合产物产率略低于LHVR饱和分。     

供氢(氘)剂在减压渣油四组分裂化中的作用及其同位素效应

研究了辽河减渣四组分在微型高压釜内中临氮热裂化、临氢热裂化和临氢催化加氢反应,考察了供氢剂或供氘剂对上述反应的影响。结果表明,临氮热裂化时沥青质是大量生焦的物种,胶质的生焦能力不显著,芳香分、饱和分不生焦;临氢热裂化沥青质生焦量减少,胶质很少生焦,芳香分和饱和分不生焦;临氢催化加氢时,辽河减渣四组分在临氢反应基础之上,生焦量进一步降低。辽河减渣四组分在临氮热裂化、临氢热裂化和临氢催化加氢过程中添加供氢剂或供氘剂后,生焦反应得到显著抑制,相比之下供氢剂的作用更为明显。三种氢源都具有抑制渣油四组分缩合或缩聚反应的作用。渣油四组分从供氢剂或供氘剂中获得氢（氘）的能力不同,沥青质>胶质>芳香分≈饱和分。就同一组分而言,供氢剂或供氘剂的表观供氢（氘）率随反应条件不同而不同,临氮热裂化> 临氢热裂化>临氢催化加氢过程。供氢剂与供氘剂在所有的过程中都存在明显的动力学效应,并且这个动力学效应随加工环境的不同而变化,在临氮热裂化过程中动力学同位素效应明显。在临氢热裂化过程,尤其是催化加氢裂化过程中动力学效应逐渐变得不明显。2H-NMR分析表明,氘代四氢萘的环烷环中的α位比β位的脱氢选择性高,氘代四氢萘脱氢选择性大小的顺序为：临氮热裂化>临氢热裂化>临氢催化加氢过程。     

Study on liquid oxygen compatibility of bromine‐containing epoxy resins for the application in liquid oxygen tank

The liquid oxygen compatible epoxy resin was obtained by the polycondensation between tetrabromobisphenol A and neat epoxy resins. The results of liquid oxygen impact test indicated that the synthetic epoxy resins were compatible with liquid oxygen. The relationship between impact reaction sensitivity (IRS) and flame retardancy were studied by liquid oxygen impact test and limiting oxygen index test. The results showed that the flame‐retardant modification of epoxy resin was valuable to reduce the IRS. The thermal gravimetric analysis results indicated that the Br · radical was quickly released in relatively low temperature (approximately 370°C) for compatible epoxy resin. The Br · radical was a key factor to promote the epoxy resin compatible with the liquid oxygen. The X‐ray photoelectron spectroscopy was used to survey the distribution of functional groups on the surface of samples before and after impact. The results showed that the oxidation reaction and carbonization process may occur on the surface of samples after impact. The liquid oxygen compatibility mechanism is proposed in this paper. The bromine‐containing epoxy resin has the potential to be the material used in liquid oxygen tank. Copyright © 2015 John Wiley & Sons, Ltd.     

Effects of petroleum resins on asphaltene aggregation and water-in-oil emulsion formation

Asphaltenes from four crude oils were fractionated by precipitation in mixtures of heptane and toluene. Solubility profiles generated in the presence of resins (1:1 mass ratio) indicated the onset of asphaltene precipitation occurred at lower toluene volume fractions (0.1–0.2) than without resins. Small-angle neutron scattering (SANS) was performed on solutions of asphaltene fractions in mixtures of heptane and toluene with added resins to determine aggregate sizes. Water-in-oil emulsions of asphaltene–resin solutions were prepared and separated by a centrifuge method to determine the vol.% water resolved. In general, the addition of resins to asphaltenes reduced the aggregate size by disrupting the π–π and polar bonding interactions between asphaltene monomers. Interaction of resins with asphaltenic aggregates rendered the aggregates less interfacially active and thus reduced emulsion stability. The smallest aggregate sizes observed and the weakest emulsion stability at high resin to asphaltene (R/A) ratios presumably corresponded to asphaltenic monomers or small oligomers strongly interacting with resin molecules. It was often observed that, in the absence of resins, the more polar or higher molecular weight asphaltenes were insoluble in solutions of heptane and toluene. The addition of resins dissolved these insolubles and aggregate size by SANS increased until the solubility limit was reached. This corresponded approximately to the point of maximum emulsion stability. Asphaltene chemistry plays a vital role in dictating emulsion stability. The most polar species typically required significantly higher resin concentrations to disrupt asphaltene interactions and completely destabilize emulsions. Aggregation and film formation are likely driven by polar heteroatom interactions, such as hydrogen bonding, which allow asphaltenes to absorb, consolidate, and form cohesive films at the oil–water interface.