CO2 gasification of woody biomass chars: The influence of K and Si on char reactivity

Although the influence of metallic and alkaline elements on biomass char reactivity is well known, a quantitative assessment of this catalytic effect is hard to obtain because of the chemical and textural complexity of biomass. The effect of K and Si on the CO₂ gasification reactivity of a biomass char was studied using thermogravimetric analysis. A beech sample was pyrolyzed at 800 °C and then impregnated with known amounts of silicon or potassium allowing to obtain a wide range of K/Si ratios. The reactivity of the impregnated samples was studied under a CO₂ (20% vol.) atmosphere. The results show that at low conversion ratios, the char reactivity depends on its textural properties, with strong diffusional limitations. When conversion reaches 60%, the presence of a catalyst (K) and an inhibitor (Si) becomes the major parameter influencing reactivity. From these experiments, a general trend was obtained between K/Si ratio and reactivity as a function of conversion.     

Adsorption of carbonyl sulfide on modified activated carbon under low-oxygen content conditions

Activated carbon sorbents impregnated with KOH, Fe(NO₃)₃, Cu(NO₃)₂, Zn(NO₃)₂ or Co(NO₃)₂ and their applications in catalytic oxidation reaction of COS were investigated. The results showed that the activated carbon modified with 10 % (mass percentage) KOH enhanced the adsorption ability significantly. And it was also found that the oxygen content and temperature were the two most important factors in the COS adsorption. Further investigation on the pore structures of the samples with X-ray photoelectron spectroscopy indicated that an adsorption/oxidation process happened in the KOH modified activated carbon in which the major existing forms of sulfur were SO₄ ^2? and S species. The oxidation of COS suggested that KOH in the micropores may play a catalytic role during the adsorption. On the other hand, we found that the desorption activation energy from KOHW was higher than that from AC by the CO₂-TPD spectra, which indicated the adsorption of CO₂ on KOH impregnated activated carbon was stronger. The strong adsorption could be attributed to the basic groups on the activated carbon surface. In conclusion, the activated carbon impregnated with KOH promises a good candidate for COS adsorbent.     

Optimization of preparation conditions for activated carbon from palm oil fronds using response surface methodology on removal of pesticides from aqueous solution

Palm oil fronds were used to prepare activated carbon using the physiochemical activation method, which consisted of potassium hydroxide (KOH) treatment and carbon dioxide (CO₂) gasification. The effects of variable parameters activation temperature, activation time and chemical impregnation ratios (KOH: char by weight) on the preparation of the activated carbon and for the removal of pesticides: bentazon, carbofuran and 2,4-Dichlorophenoxyacetic acid (2,4-D) were investigated. Based on the central composite design (CCD), two factor interaction (2FI) and quadratic models were respectively employed to correlate the effect of variable parameters on the preparation of activated carbon used for the removal of pesticides with carbon yield. From the analysis of variance (ANOVA), the most influential factor on each experimental design response was identified. The optimum conditions for preparing the activated carbon from oil palm fronds were found as follows: activation temperature of 750 °C, activation time of 2 h and chemical impregnation ratio of 2.38. The percentage error between predicted and experimental results for the removal of bentazon, carbofuran and 2,4-D were 8.2, 1.3 and 9.2%, respectively and for the yield of the palm oil frond activated carbon was 5.6.     

Effects of phosphoric acid as additive in the preparation of activated carbon fibers from poly(p-phenylene benzobisoxazole) by carbon dioxide activation

Poly(p-phenylene benzobisoxazole) (PBO) was impregnated with small amounts of H₃PO₄, and the effects of this additive on the porosity and other characteristics of chars and activated carbon fibers (ACFs) derived from this polymer were investigated. To this end, PBO-AS impregnated with 5, 10 or 15 wt.% H₃PO₄ was pyrolyzed at 850 °C, and the resulting chars were physically activated with carbon dioxide at 800 °C to different burn-off (BO) degrees. Thermal analysis techniques only detected minor effects of H₃PO₄ on PBO pyrolysis. The char yield and char reactivity towards CO₂ increased following PBO-AS impregnation with H₃PO₄. Structural (X-ray diffraction), porous textural (CO₂ adsorption) and surface chemical (temperature-programmed desorption, X-ray photoelectron spectroscopy) characterizations of the pyrolysis chars indicated that the increase in char reactivity is probably associated with a higher content of oxygenated functionalities. Following CO₂ activation, the surface area and pore volume of the obtained ACFs chiefly depended on the BO degree, but impregnation with H₃PO₄ restricted the pore size to the micropore and narrow mesopore range, thus producing adsorbents with a slightly narrower pore size distribution than in the absence of H₃PO₄. The results are compared with those previously obtained under equivalent conditions with other high-crystallinity polymers as precursors for ACFs.     

烟煤焦在H2O和CO2气氛下的结构演变与气化反应性关联

本研究以烟煤在1000 ℃热解所制得的焦样为研究对象,考察了其在H₂O、CO₂及两者混合气氛下的结构演变,以及气化反应性的影响。为了探究焦样在气化过程中的结构演变,利用氮吸附、SEM和拉曼光谱等表征手段分析不同碳转化率下的焦样结构。结果表明,H₂O气氛对焦样结构的演变明显不同于CO₂气氛,揭示了焦样在两种气氛下的反应路径不同。因结构演变的不同,随碳转化率的增加,焦样在两种气氛下表现出不同的气化反应性能。在CO₂气氛下,焦样的气化反应速率随碳转化率的增加而逐渐降低,与H₂O气氛存在下变化趋势相反。在H₂O和CO₂共气化条件下,煤焦在H₂O和CO₂混合气氛下的反应速率高于单气氛下的反应速率的计算值,表现出一定的协同作用。这是因为焦样与H₂O反应能够产生较大的比表面积,为焦样与CO₂反应提供更多的反应场所,促进了焦样与CO₂的反应。     

Thermogravimetric analysis on gasification reactivity of Hailar lignite

Comparative studies on the Hailar lignite pyrolysis/gasification characteristics at N₂/CO₂ atmosphere and the influence of inherent mineral matters, external ash and pyrolysis temperature on its reactivity during gasification at CO₂ atmosphere were conducted by non-isothermal thermogravimetric analysis, FTIR, and X-ray diffraction (XRD) analysis. Thermogravimetric test results show that the atmosphere of N₂ or CO₂ almost has no effects on the pyrolysis behavior, and the gasification reaction under CO₂ atmosphere occurs over 943?K at the heating rate of 40?K?min^?1. The external ash prepared at 1173 and 1223?K shows a certain catalytic effect on promoting the gasification reaction, although the inherent mineral matters of Hailar lignite are found in stronger catalytic effects on gasification than the external ash. The lignite gasification reactivity decreases with increasing pyrolytic temperature between 1073 and 1273?K.     

碱金属助剂类型及前驱物对改性NiAl复合氧化物催化分解N2O活性的影响

制备了不同Ni/Al原子比的NiAl类水滑石样品,焙烧获得NiAl复合氧化物,用于N₂O分解反应,研究了NiAl复合氧化物组成对催化活性的影响。在活性较高的NiAl复合氧化物表面浸渍碱金属碳酸盐溶液,制备改性NiAl复合氧化物,考察了碱金属类型（Na、K、Cs）和钾前驱物（K₂CO₃、K₂C₂O₄、CH₃COOK、KNO₃）对改性催化剂活性的影响。用XRD、ICP-AES、FT-IR、BET、H₂-TPR、XPS技术表征了催化剂的组成结构。结果表明,Ni/Al原子比为2.7的NiAl复合氧化物催化活性较高;Na、K、Cs碳酸盐改性NiAl复合氧化物均提高了催化剂活性,其中K的助剂效应最强。钾前驱物对K改性NiAl复合氧化物的催化活性有显著影响,其中碳酸钾、醋酸钾、草酸钾的加入明显提高了改性催化剂的催化活性,而加入硝酸钾反而降低了催化剂活性。     

Thermogravimetric analysis of gasification reactivity of coal chars with steam and CO2 at moderate temperatures

Comparative study on the gasification reactivity of the three types of Chinese coal chars with steam and CO₂ at 850–1050 °C was conducted by isothermal thermogravimetric analysis. The effects of coal rank, pore structure, ash behavior, and gasification temperature on the gasification reactivity of coal chars were investigated. It is found that the gasification reactivity difference between different coal chars changes with reaction degree and gasification temperature, and has no immediate connection with coal rank and initial pore structure. Ash behavior plays an important role in the char reactivity, and changes with gasification temperature and reaction degree due to the variation in the compositions and relative amount. The influence of pore structure is more noticeable during a relatively moderate reaction process. The relative reactivity ratio of steam to CO₂ gasification generally decreases with the increasing temperature, and is related with the catalytic effect of inherent minerals. The characteristic parameters of the chars were analyzed, finding that the value of half reaction specific rate is approximate to the average specific rate under the same conditions. The nth-order distributed activation energy model is proposed to describe the coal char gasification process, and the results show that the activation energy increases with the increasing carbon conversion.     

Synthesis of High‐Surface‐Area Nitrogen‐Doped Porous Carbon Microflowers and Their Efficient Carbon Dioxide Capture Performance

Sustainable carbon materials have received particular attention in CO₂ capture and storage owing to their abundant pore structures and controllable pore parameters. Here, we report high‐surface‐area hierarchically porous N‐doped carbon microflowers, which were assembled from porous nanosheets by a three‐step route: soft‐template‐assisted self‐assembly, thermal decomposition, and KOH activation. The hydrazine hydrate used in our experiment serves as not only a nitrogen source, but also a structure‐directing agent. The activation process was carried out under low (KOH/carbon=2), mild (KOH/carbon=4) and severe (KOH/carbon=6) activation conditions. The mild activated N‐doped carbon microflowers (A‐NCF‐4) have a hierarchically porous structure, high specific surface area (2309 m² g^?1), desirable micropore size below 1 nm, and importantly large micropore volume (0.95 cm³ g^?1). The remarkably high CO₂ adsorption capacities of 6.52 and 19.32 mmol g^?1 were achieved with this sample at 0 °C (273 K) and two pressures, 1 bar and 20 bar, respectively. Furthermore, this sample also exhibits excellent stability during cyclic operations and good separation selectivity for CO₂ over N₂.     

Highly efficient CO2 capture with a metal–organic framework‐derived porous carbon impregnated with polyethyleneimine

Global warming is considered as one of the great challenges of the twenty‐first century. Application of CO₂ capture and storage technologies to flue gas is considered to be a useful method of lessening global warning. Highly porous carbon has played an important role in tackling energy and environmental problems. We attempted to synthesize a highly porous carbon adsorbent by carbonizing a highly crystalline metal–organic framework (MOF) without any carbon precursors and focused on the adsorption of CO₂ and CH₄ gases and CO₂/CH₄ selectivity at 298, 323 and 348 K using a volumetric apparatus. The MOF‐derived porous carbon (MDC) was prepared by direct carbonization of MOF‐199 as a template at 900 °C under nitrogen atmosphere. Amino‐impregnated MDC samples exhibited enhanced adsorption capacities by a combination of physical and chemical adsorption. Polyethyleneimine (PEI) was selected as the amine source, which was found to greatly enhance CO₂ capture when supported on the porous carbon. Novel PEI‐impregnated MDC nanocomposites were synthesized by wetness impregnation and then characterized using various methods.     

Mechanistic Investigation of Alkali-Treated Photocatalytic CO2 Reduction: The Role of OH− and Metal Cations for Almost 100 % Selectivity of CO

In this work, the modulation of activity and selectivity via photoreduction of carbon dioxide under simulated sunlight was achieved by treating P25 and P25/Pt NPs with KOH. It found that KOH treatment could significantly improve the overall conversion efficiency and switch the selectivity for CO. Photoelectric characterizations and CO₂-TPD demonstrated that the synergistic effect of K⁺ and OH^- accelerated the separation and migration of photogenerated charges, and also improved CO₂ adsorption level. Significantly, the K ions could act as active sites for CO₂ adsorption and further activation. In situ FTIR measurements and DFT calculations confirmed that K⁺ enhanced the charge density of adjacent atoms and stabilize CO* groups, reducing the reaction energy barrier and inducing the switching of original CH₄ to CO, which played a selective regulatory role. This study provides insights into the photocatalytic activity and selectivity of alkali-treated photocatalysts and facilitates the design of efficient and product-specific photocatalysis.