Relation between interfacial shear strength and compressive strength of carbon fiber/epoxy resin composite strands

The mechanism with which the fiber-matrix interfacial strength exerts its influence on the compressive strength of fiber reinforced composites has been studied by measuring the axial compressive strength of carbon fiber/epoxy resin unidirectional composite strands having different levels of interfacial shear strength. The composite strands are used for experiments in order to investigate the compressive strength which is not affected by the delamination taking place at a weak interlayer of the laminated composites. The interfacial strength is varied by applying various degrees of liquid-phase surface treatment to the fibers. The efficiency of the compressive strength of the fibers utilized in the strength of the composite strands is estimated by measuring the compressive strength of the single carbon filaments with a micro-compression test. The compressive strength of the composite strands does not increase monotonically with increasing interfacial shear strength but showes lower values at higher interfacial shear strengths. With increasing interfacial shear strength, the suppression of the interfacial failure in the misaligned fiber region increases the compressive strength, while at higher interfacial shear strengths, the enhancement of the crack sensitivity decreases the compressive strength.     

Analysis of single-fiber pull-out from composites by using stress birefringence

During a fiber pull-out test, it is desirable to analyze the stress profiles along the embedded fiber directly within the same time scale as the normal pull-out tests. In the present study, the axial tensile stress profiles of the fiber in a model composite are measured during the single-fiber pull-out tests by using stress birefringence of the fiber. It is concluded from the analysis of the measured stress profiles that an effective radius of matrix, i.e. a radius defining the region of the matrix where the major deformation takes place, is not constant but is an increasing function of the interfacial shear stress. By incorporating the variable values of the effective radius of matrix into the shear-lag model, the axial tensile and the interfacial shear stress profiles are calculated. To accurately estimate the interfacial shear strength, the stress distribution along the embedded fiber and the variability of the effective radius of matrix should be taken into account instead of calculating the interfacial shear strength simply from the pull-out stress and the embedded length.     

Maintenance of highly interfacial shear strength by diblock copolymer between carbon fiber and epoxy resin in hostile environment

The environmental resistance properties of carbon fiber (CF), with various surface modifications, reinforcing epoxy resin composites have been studied by a microbond test. The results of cooling–heating cycling between ?40 and 95?°C indicate that the introduction of the flexible poly(n-butyl acrylate) (PnBA) blocks into the interface can effectively decrease the interfacial degradation rate, induced by interfacial thermal stress. After 50 cooling–heating cycles, the interfacial shear strength between CF and epoxy resin was still as high as 32.69?±?2.13?MPa. The results of hygrothermal treatment by immersing the composites in hot water show that assembly morphology of the diblock copolymer hydroxyl-terminated poly(n-butyl acrylate-b-glycidyl methacrylate) (OH-PnBA-b-GMA) at the interface can decrease the interfacial water absorption and thus increase the hygrothermal resistance of the composite. Besides, the length of PnBA block in the diblock copolymer influenced the interfacial properties of the composite in a hygrothermal environment.     

Relationship between fibre-matrix adhesion and the interfacial shear strength in polymer-based composites

A model is proposed to correlate the interfacial shear strength at the fibre-matrix interface, measured by means of a fragmentation test on single fibre composites, to the reversible work of adhesion between both solids, this quantity being defined as the sum of the dispersive and the acid-base interactions (physical interactions) between the fibre and the matrix. Whatever the nature of the fibres and the matrices, a linear relationship, passing through the origin, is established between the interfacial shear strength and the reversible work of adhesion. However, the slope of this straight line depends on the elastic properties and, more precisely, on the elastic moduli of both the fibre and the matrix. This leads us to express the reversible work of adhesion as the product of a mean intermolecular distance at the interface and an adhesive pressure related to the interfacial shear strength. The limits of the theoretical and experimental approaches leading to the establishment of such a model, as well as its domain of validity, are discussed.     

Effects of residual stress and interfacial frictional shear stress on interfacial debonding at notch-tip in two-dimensional unidirectional composite

A calculation method based on the shear lag approach was presented to get an approximate estimate of influences of residual stresses and frictional shear stress at the debonded interface on the interfacial debonding behavior at the notch-tip along fiber direction in two-dimensional unidirectional double-edge-notched composites. With this method, the energy release rate for initiation and growth of debonding as a function of composite stress were calculated for some examples. The calculation results showed in outline how much the tensile and compressive residual stresses in the matrix and fiber along fiber direction, respectively, act to hasten the initiation and growth of the debonding when the final cut element in the notch is matrix, while they act to retard them when the final cut element is fiber, and how much the frictional shear stress at the debonded interface reduces the growth rate of the debonding.     

Effects of plasma surface modification on the mechanical properties of carbon fiber and carbon fiber/epoxy composite

_The effect of surface treatment on mechanical properties of carbon fibers has been investigated by application of plasma polymerization of selected monomers in the vapor phase. The role of the fiber-matrix interface on carbon fiber-reinforced epoxy resin composites has also been studied. Composites have been prepared separately by the use of plasma-modified and unmodified carbon fibers in the epoxy resin matrix. The mechanical properties of carbon fibers (Hercules and Grafil) as well as of fiber/epoxy composites were examined by using single filament and three-point bending tests, respectively. It was observed that plasma polymerization treatment at selected plasma conditions led to significant improvement of interlaminar shear and flexural strength values of composites.     

A nonlinear PSE method for two-fluid shear flows with complex interfacial topology

A nonlinear stability method is developed for laminar two-fluid shear flows which undergo changes in the interface topology. The method is based on the nonlinear parabolized stability equations (PSE) and incorporates a scalar-based interface capturing (IC) scheme in order to track complex deformations of the fluid interface. In doing so, the formulation retains the flexibility and physical insight of instability-wave based methods, while providing hydrodynamic modeling capabilities similar to direct numerical calculations: the new formulation, referred to as the IC-PSE, can capture the nonlinear physical mechanisms responsible for generating large-scale, two-fluid structures, without incurring heavy computational costs. This approach is valid for spatially developing, laminar two-fluid shear flows which are convectively unstable, and can naturally account for the growth of finite amplitude interfacial waves, along with changes to the interfacial topology. We demonstrate the accuracy of the IC-PSE against direct Navier–Stokes calculations for two-fluid mixing layers with density and viscosity stratification. The comparisons show that the IC-PSE can predict the dynamics of the instability waves and capture the formation of Kelvin–Helmholtz vortex rolls and large scale liquid structures, at an order of magnitude less computational cost than direct calculations. The role of surface tension in the IC-PSE formulation is shown to be valid for flows in which Re/We ? 1, and the method accurately predicts the formation and non-linear evolution of flow structures in this limit. This is demonstrated for spatially developing mixing layers which lead to vortex roll-up and ligaments, prior to droplet formation. The pinch-off process itself is a high surface tension phenomenon and in not considered herein. The method also accurately captures the effect of interfacial waves on the mean flow, and the topology changes during the non-linear evolution of the two-fluid structures.     

Growth of interfacial debonding in notched two-dimensional unidirectional composite under stress and displacement controls

A simplified calculation method for study of the growth of interfacial debonding between elastic fiber and elastic matrix ahead of the notch-tip in composites under displacement and stress controlled conditions was presented based on the shear lag approach in which the influences of residual stress and frictional shear stress at the debonded interface were incorporated. The calculation method was applied to a model two-dimensional composite. An outline is given of the difference and similarity in the growing behavior of the debonding between the displacement and stress controls, and of the influences of the residual stresses, frictional shear stress, the nature of the final cut component (fiber or matrix) and sample length on the debonding behavior.     

Improvement and mechanism of interfacial adhesion in PBO fiber/bismaleimide composite by oxygen plasma treatment

The improved interfacial adhesion of PBO fiber-reinforced bismaleimide composite by oxygen plasma processing was investigated in this paper. After treatment, the maximum value of interlaminar shear strength was 57.5 MPa, with an increase of 28.9%. The oxygen concentration of the fiber surface increased, as did the surface roughness, resulting in improvement of the surface wettability. The cleavage and rearrangement of surface bonds created new functional groups OCO, NCO and NO, thereby activating the fiber surface. And long-time treatment increased the reaction degree of surface groups while destroyed the newly-created physical structures. The enhancement of adhesion relied primarily on the strengthening of chemical bonding and mechanical interlocking between the fiber and the matrix. The composite rupture planes indicated that the fracture failure shifted from the interface to the matrix or the fiber.     

Preparation of vertically aligned carbon nanotube arrays grown onto carbon fiber fabric and evaluating its wettability on effect of composite

Vertically aligned carbon nanotube (CNT) arrays have been grown onto the carbon fiber fabric using a catalytic chemical vapor deposition (CCVD) method. The as-synthesized CNT arrays are about 20 μm in height, and the nanotube has a mean inner and outer diameter of 2.6 nm, 5.5 nm, respectively. The CNT-grafted carbon fabric shows a hydrophobic property with a contact angle over 145°, and the single CNT-grafted carbon fiber shows a sharp increase of dynamic contact angle in de-ionized water from original 71.70° to about 103°, but a little increase does in diiodomethane or E-51 epoxy resin. However, the total surface energy of carbon nanotube-grafted carbon fiber is almost as same as that of as-received carbon fiber. After CNTs growth, single fiber tensile tests indicated a slight tensile strength degradation within 10% for all different lengths of fibers, while the fiber modulus has not been significantly damaged. Compared with the as-received carbon fibers, a nearly 110% increase of interfacial shear strength (IFSS) from 65 to 135 MPa has been identified by single fiber pull-out tests for the micro-droplet composite, which is reinforced by as-received carbon fiber or CNT-grafted carbon fiber.     

Interface and its effect on the interlaminate shear strength of novel glass fiber/hyperbranched polysiloxane modified maleimide-triazine resin composites

Interface is the key topic of developing advanced fiber reinforced polymeric composites. Novel advanced glass woven fabric (GF) reinforced composites, coded as GF/mBT, were prepared, of which the matrix resin was hyperbranched polysiloxane (HBPSi) modified maleimide-triazine (mBT) resin. The influence of the composition of the matrix on the interfacial nature of the GF/mBT composites were studied and compared with that of the composite based on GF and BT resin using contact angle, X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), and dielectric properties over wide frequency and temperature ranges. Results show that the interfacial nature of the composites is dependent on the chemistries of the matrices, mBT matrices have better interfacial adhesion with GF than BT resin owing to the formation of chemical and hydrogen bonds between mBT resin and GF; while in the case of mBT resins, the content of HBPSi also plays an important role on the interfacial feature and thus the macro-performance. Specifically, with increasing the content of HBPSi in the matrix, the interlaminate shear strength of corresponding composites significantly improves, demonstrating that better interfacial adhesion guarantees outstanding integrated properties of the resultant composites.     

Quantitative evaluation of interfacial adhesion between fiber and resin in carbon fiber/epoxy composite cured by semiconductor microwave device

Interfacial adhesion between carbon fiber (CF) and epoxy resin in carbon fiber-reinforced epoxy composite, which was prepared by different heating process such as semiconductor microwave (MW) device and conventional electric oven, has been evaluated quantitatively. The interfacial shear strength (IFSS) between CF and epoxy resin, which was an indicator of adhesion on the interface, was measured by a single fiber fragmentation test. The single fiber fragmentation test showed that the IFSSs of the prepared specimens were different by heating methods. In the case of MW process, the curing reaction of epoxy resin on the CF interface would be progressed preferentially due to the selective heating of CF, resulting that the IFSSs of specimens prepared by MW irradiation were increased by enhancing the output power of MW. However, the IFSSs of the specimens were decreased by excessively high output power because the matrix resin on the CF interface was thermally degraded. As results, by optimizing the MW conditions of output power and irradiation time, the IFSS of the sample cured by MW was increased by 21% as compared to oven-heated one. It was found that the interfacial adhesion between CF and epoxy resin would be improved by the MW-assisted curing reaction on the surface of CF.     

一种用于光纤链路振动信号模式识别的规整化复合特征提取方法

相位光时域反射链路监测系统是一种利用光纤作为传感介质的传感系统, 能够监测、定位、识别入侵信号.模式识别模块是其重要组成部分, 实时智能区分安全扰动和危险入侵.本文提出一种用于光纤链路振动信号模式识别的复合特征提取方法.利用改进的双门限方法确定有效信号段的起止位置, 结合最大能量与最高信噪比挑选出采样周期内主要入侵扰动的特征段.综合利用特征段时域持续时间和小波包能量谱提取复合特征向量, 使用支持向量机进行模式识别.实验表明, 基于本文提出的规整化特征提取方法的模式识别准确率有了显著提高.     

A novel method for simultaneous measurement of current and voltage using one low-birefringence fiber

A novel method for simultaneous measurement of current and voltage employing a single monomode low-birefringence (Lo-Bi) fiber is described. This uses the Faraday effect for detection of current and the Kerr effect for detection of voltage. The waveform of the output light intensity due to the Kerr effect has been detected and the Kerr constant was measured as 5.4×10⁻¹⁶ m/V⁻² at 25°C. Theoretical analysis shows that the current component can be measured free from the influence of the voltage component and the two components can be easily separated.     

Formation of adhesive phase onto high strength and modulus PE fiber by PE solution treatment for making PE fiber-reinforced PE composite

The method for the formation of adhesive phase onto polyethylene (PE) fiber surface by passage of the PE fiber through hot PE solutions has been investigated for making composite materials reinforced by the PE fibers. When the PE fiber is treated by the low density PE (LDPE) solution in o-xylene in the range of 120 to 135^°C, the tensile strength of the PE fiber is maintained at that of the original PE fiber. Adhesive strength between the PE fiber surface and LDPE phase formed on the PE fiber through the hot PE solution is found to be so high that the PE fiber itself is torn off. The application of the present method to PE fiber-reinforced PE composites will be expected.