Oxygen transport properties of dense and porous (La0.8Sr0.2)0.99Co0.8Ni0.2O3-δ

We have determined k_ex and D_chem for (La_0.8Sr_0.2)_0.99Co_0.8Ni_0.2O_3-δ by the use of electrical conductivity relaxation on a dense sample and by applying the ALS model to measured AC impedance spectrum on a porous electrode. Extracting k_ex and D_chem from the methods resulted in comparable values. k_ex and D_chem also agreed well with literature values on La_0.8Sr_0.2CoO_3-δ, indicating that nickel substitution does not change the oxygen transport properties. k_ex of the porous sample was further found to decrease with a five times higher rate than D_chem when measured by using an Electrochemical Impedance Spectroscopy (EIS) over several days.     

Dielectric and ferroelectric properties of 0.8PZT–0.2PCN ceramics under sintering conditions variation

The influences of sintering conditions on electrical properties of the 0.8Pb(Zr_1/2Ti_1/2)O₃–0.2Pb(Co_1/3Nb_2/3)O₃ ceramics have been investigated with sintering temperatures of 1175, 1200, 1225, and 1250 °C and dwell times for 2, 6, and 10 h. The crystal structure of dense specimens showed coexistence between tetragonal, rhombohedral and pseudo cubic phases in all sintering temperatures, while tetragonal-rich phase appeared with increasing dwell times. A maximum dielectric constant was observed at sintering condition of 1200 °C for 2 h, while the transition temperature slightly increased with increasing dwell time. All ceramics also showed diffused phase transition behaviors with a minimum diffusivity at sintering condition of 1200 °C for 2 h. In addition, the polarization–electric field (P–E) hysteresis loops of the ceramic systems also changed significantly with sintering conditions. Interestingly, the ferroelectric parameters; remnant polarization (P_r) and loop squareness (R_sq) tended to increase with increasing sintering temperatures and dwell times.     

Ionic conduction in BaxCe0.8Er0.2O3−α

Ba_xCe_0.8Er_0.2O_3−α (x=0.98–1.03) solid electrolytes were synthesized by high temperature solid-state reaction. X-ray diffraction (XRD) patterns showed that the specimens were a single perovskite-type orthorhombic phase. The conduction properties of the specimens were studied electrochemically in the temperature range of 600–1000 °C. The influence of nonstoichiometry in the specimens with x≠1 on conduction properties was investigated and compared with that in the specimen with x=1. These three specimens showed a good protonic conduction under wet hydrogen, a mixed conduction of oxide-ion and electronic hole under dry higher oxygen partial pressure, and a mixed conduction of proton, oxide-ion and electronic hole under wet higher oxygen partial pressure. Both of the protonic and oxide-ionic conductivities increased with increasing barium content in the specimens under wet hydrogen and dry air, respectively.     

Ni0.8Zn0.2Fe2O4和CO2Y添加Ni0.8Zn0.2Fe2O4磁性质对比研究

采用固相反应法制备了Ni0.8Zn0.2Fe2O4和2wt％ Co2Y添加Ni0.8Zn0.2Fe2O4铁氧体多晶样品,并对样品的磁性质进行了研究.实验发现,添加Co2Y后,铁氧体的磁损耗明显下降,相同条件下Q值增大到原来的3倍左右.对添加Co2Y引起铁氧体磁损耗下降的原因进行了讨论,认为主要是钴离子掺杂引起的铁氧体磁滞损耗明显降低所导致的.     

MSM结构Mg0.2Zn0.8O可见盲光电探测器

采用射频磁控溅射,通过传统的紫外曝光和湿法腐蚀的方法,制备了不同电极间距的金属-半导体-金属(MSM)结构Mg0.2Zn0.8O可见盲光电探测器.研究了器件的暗电流和响应度随电极间距的变化关系,当施加的电压没有达到贯穿电压的时候,暗电流和响应度均随着电极间距的增加而减小,并对其具体的机制进行了研究.     

Mössbauer and X-ray studies for Ni0.2ZnxMg0.8−xFe2O4 ferrites

The spinel ferrites of Ni_0.2Zn_xMg_0.8−xFe₂O₄, 0⩽x⩾0.8, were studied at room temperature using X-ray diffraction and Mössbauer patterns. The analysis of the X-ray diffraction patterns proved that the samples have a single phase cubic spinel structure. The calculated values of the theoretical, true and average lattice constants, tetrahedral bond, tetrahedral edge and unshared octahedral edge were found to increase while the shared octahedral edge and octahedral bond decrease as the Zn²⁺ ion substitution increases. Mössbauer studies showed that the samples for x=0, 0.2 and 0.4 are magnetic and show rather broad lines, while for x=0.6 and 0.8 are paramagnetic. The hyperfine parameters of the tetrahedral and octahedral sites were determined as functions of composition x. The cation distributions were deduced and supported by X-ray studies. The B-site pattern was composite and has been fitted into multicomponents and the deduced hyperfine parameters have been discussed as a function of x.     

Synthesis and structure of Mg(Fe0.8Ga0.2)2O4−δ film materials

Features of the preparation of magnetic semiconductor films with the composition Mg(Fe_0.8Ga_0.2)₂O_4?δ on a 200-nm-thick silicon substrate are presented. Both a pure substrate surface and one with protective TiO _x layers with a crystallization temperature of 900–1000°C for 30 min were used. The effect of the protective layers on the formation of the surface morphology of the films and their magnetic properties is shown.     

On the structural stability and oxygen permeation behavior of inorganic SrCo0.8Fe0.2O3−δ membranes

The high oxygen permeability combined with reasonable structural stability of perovskite-type ABO_3−δ compounds is vital for their potential applications in gas separation, solid oxide fuel cells, sensors, etc. Hence, an attempt is made to develop SrCo_0.8Fe_0.2O_3−δ-based dense membranes with sol-gel-derived oxalates and study their phase stability and oxygen permeation. While X-ray diffraction confirms the presence of a perovskite-type cubic phase above 800 °C, X-ray photoelectron spectroscopy reveals the presence of cobalt and iron in 3+ and 4+ oxidation states with O₂ ²⁻, O₂ ⁻ and O⁻ species. The electrical conductivity increases up to a characteristic temperature and decreases slowly thereafter via pronounced carrier scattering. A 1.5-mm-thick membrane displays reasonable oxygen permeability of 1.05 × 10⁻⁶ mol cm⁻² s⁻¹ at 900 °C but has inadequate stability. Partial substitution of iron with zirconium is shown to improve permeability and stability significantly. Thus, SrCo_0.8Fe_0.15Zr_0.05O_3−δ membrane shows promise for oxygen permeation purposes.

     

The chemical stability and conductivity improvement of protonic conductor BaCe0.8 − x Zr x Y0.2O3 − δ

A series of BaCe_0.8???x Zr _x Y_0.2O_3???δ (BCZYx) (x?=?0, 0.2, 0.4, 0.6, 0.8) powders were prepared by EDTA–citrate complexing sol–gel process in this paper. The electrical conducting behavior, as well as chemical stability, was investigated. X-ray diffraction (XRD) results reveal that all samples are homogenous perovskite phases. Observed from XRD patterns and thermogravimetric curves, the samples with x?≥?0.4 survive in the pure CO₂, while samples with various Zr contents all present structurally stable against steam at 800 °C. The Zr-free sample of BaCe_0.8Y_0.2O_3???δ possesses the maximum bulk conductivity, 4.25?×?10^?2 S/cm, but decomposes into Ba(OH)₂ and Ce_0.8Y_0.2O_3???δ in steam. A negative influence of increasing Zr content on the conductivity of BCZYx can be observed by impedance tests. Considering the effect of temperature on the bulk conductivity, BCZY0.4 is preferred to be applied in SOFC as a protonic conductor, ranging from 1.52?×?10^?4 to 1.51?×?10^?3 S/cm (500–850 °C) with E _a?=?0.859 eV, which is proved to be a good protonic conductor with t _H+?≥?0.9.     

Structural,dielectric and optical properties of sol–gel synthesized 0.55Ba(Zr0.2Ti0.8)O3–0.45(Ba0.7Ca0.3)TiO3 ceramic

Lead-free polycrystalline ceramic 0.55Ba(Zr_0.2Ti_0.8)O₃–0.45(Ba_0.7Ca_0.3)TiO₃ (0.55BZT–0.45BCT) was synthesized by sol–gel method and the dielectric, impedance and optical properties of this ceramic were studied. X-ray diffraction analysis revealed the formation of pure perovskite phase with the coexistence of tetragonal and rhombohedral structures. The high value of dielectric constant (~6,985) with low dielectric loss (~0.013) was obtained at room temperature. Bulk and grain boundary resistances were measured by impedance analysis, which revealed negative temperature coefficient of resistance behaviour in this ceramic. The estimated value of optical band gap was found to be ~3.16 eV, which is related to the presence of intermediate energy levels. Two emission bands one at ~365 nm (UV region) and another at ~465 nm (blue region) were observed in photoluminescence spectrum at room temperature.     

Mixed Conduction in BaCe0.8Pr0.2O3-α Ceramic

以高温固相反应法合成了BaCe0.8Pr0.2O3-α陶瓷,用X射线衍射法对其结构进行了表征. 用交流阻抗谱、气体浓差电池和氢泵方法测定了材料在500-900 ffiC、不同气氛中的电导率以及离子迁移数,研究了材料的导电特性. 结果表明,该陶瓷材料为单一钙钛矿型斜方晶结构. 在500-900ffiC下,在干燥和潮湿的氧气、空气和氮气气氛中,材料以电子空穴导电为主,其总电导率随氧分压的增加而稍有增加;在潮湿的氢气气氛中,材料以离子导电为主,其总电导率比不含氢气气氛(O2,air,N2)中的电导率高一到两个数量级.     

(Ni0.8Zn0.2Fe2O4)epoxy-PZT双层膜中的磁电效应

讨论了Ni0.8Zn0.2Fe2O4(NZFO)与锆钛酸铅(PZT)的双层膜结构样品的磁电(ME)效应.NZFO粉料由溶胶-凝胶法制成,再经900℃热压,并高温烧结.在该双层膜中测量到了很强的磁电相互作用.发现横向的磁电效应比纵向效应大一个数量级,并且随NZFO烧结温度的提高而增加.当烧结温度从950℃上升到1380℃时,横向ME电压系数(αE)的最大值变化范围为25.6 mV Am-2≤αE≤199.6 mV Am-2.理论分析显示NZFO-PZT双层膜样品中ME效应源于NZFO与PZT之间相对良好的磁电耦合.     

Mechanical properties of La0.58Sr0.4Co0.2Fe0.8O3-δ membranes

In this paper, we report on the mechanical properties of a La_0.58Sr_0.4Co_0.2Fe_0.8O_3-δ perovskite material. We use ring-on-ring bending tests with disk-shaped samples and depth-sensitive micro-indentation. In particular, the temperature dependency of fracture stress and elastic behavior are addressed. The fracture load is measured to be ～ 40% higher at room temperature (RT) than at 800 °C, which is due to the ferro-elasticity of material at RT. The stiffness shows an increase of about 50% above 600 °C and 700 °C in vacuum and air, respectively. The effect is attributed to a rhombohedral to cubic phase transition, which is not fully reversible upon cooling. The changes in phase composition with temperature are also confirmed by in-situ high temperature XRD. The transition appears to be associated with a change of heat capacity.     

Y0.8Pr0.2Ba2Cu3O7—δ单晶的热力学参数

用ＳＱＵＩＤ磁强计测得了Ｙ０．８Ｐｒ０．２Ｂａ２Ｃｕ３Ｏ７－δ单晶在外场平行于ｃ轴条件下的磁化强度随温度的变化。在超导转变下，除了磁化强度是可逆的以外，由于磁通涨落而导致的磁化强度交叉发生在超导转变温度以下约２Ｋ处。利用Ｈａｏ－Ｃｌｅｍ模型拟合可逆磁化强度得到了热力学临界场Ｈｃ（Ｔ）和金兹堡－朗道参数ｋ。其它超导参数由Ｈｃ（Ｔ）和ｋ推得，比较ＹＢａ２Ｃｕ３Ｏ７－δ的热力学参数，讨论了Ｐｒ离子的效应     

The luminescence and energy transfer in Pr3+–Ce3+ co-doped Lu0.8Sc0.2BO3 crystals

Lu_0.8Sc_0.2BO₃ crystals doped with 1 at%Ce³⁺ and co-doped 0.1 at% and 0.5 at%Pr³⁺ were grown by the Czochralski method. The concentrations of Pr³⁺ and Ce³⁺ in crystals were measured by the ICP-AES method. Absorption spectra, VUV–UV spectra, fluorescence decay time and X-ray excitation luminescence spectra were investigated at room temperature. The excitation luminescence spectra of Ce³⁺ emission and decay curves from the lower excited state levels of the 4f¹5d¹ and 5d¹ electronic configurations of the Pr³⁺ and Ce³⁺ conspicuously indicated the non-radiative energy transfer from Pr³⁺ to Ce³⁺. The detailed pathways were shown in the energy level diagram of the respective Ce³⁺ and Pr³⁺ in Lu_0.8Sc_0.2BO₃ host. In addition, the scintillation efficiency data indicated that the energy transfer effect is directly associated with the Pr³⁺ concentration.     

Magnetic and electrical properties of (Ni0.8Cu0.2)1−x Cox Mn0.02Fe1.9O4 ferrites

The effect of Co substitution on the magnetic and electrical properties of iron-deficient nickel–copper mixed ferrites containing a small quantity of manganese oxide was investigated. The presence of Co enhances the specific magnetization although the saturation magnetization falls a little due to decrement of density. The initial permeability changes linearly with the average grain size of the materials and shows fairly good thermal stability for higher Co concentration. An appreciable increment in DC resistivity along with decrement in dielectric loss factor at 100 MHz can also be obtained for higher Co concentration.     

Microstructure and electrochemical properties of porous La2NiO4+δ electrodes spin-coated on Ce0.8Sm0.2O1.9 electrolyte

Porous La₂NiO_4+?? electrodes were prepared from superfine starting powder on dense substrates of Ce_0.8Sm_0.2O_1.9 electrolyte by a spin coating technique. The microstructure and electrochemical properties of the electrodes were investigated within the sintering temperature range of 1,000?C1,100?°C. An obvious effect of sintering temperature on the microstructure and electrochemical properties was detected. The variation of the electrochemical properties with sintering temperature was explained in relation to the microstructural evolution of the porous electrodes. It was detected that the electrode processes greatly depended on the microstructure of the electrodes. The polarization of surface oxygen exchange process was found to be the major contribution to the total electrode polarization. The electrode sintered at 1,050?°C showed the optimum electrocatalytic activity among the investigated electrodes. At 800?°C, the electrode exhibited a polarization resistance of 0.42????cm², an overpotential of 48?mV at a current density of 200?mA?cm^?2 and an exchange current density of 121?mA?cm^?2.     

Magnetic and magneto-transport properties of (Ba0.8Sr0.2)2−xNdxFeMoO6

The variation in structural, magnetic and magneto-transport properties of the double perovskite system (Ba_0.8Sr_0.2)_2?xNd_xFeMoO₆ {0.0<X<0.5} induced by Nd³⁺ doping (electron doping) has been studied and compared. The samples were prepared by standard solid state reaction method in a reducing atmosphere. The parent compound showed a saturation magnetic moment value of 3.75 μ_B/f.u. at an applied field of 0.5 T and a change in magnetoresistance value up to 26% (77 K, 0.8 T). The Rietveld refinement of the X-ray diffraction data showed a continuous decrease in lattice parameters and Fe–Mo ordering with increasing Nd³⁺ doping. The Curie temperature was found to increase with Nd³⁺ doping (3 K per % of Nd) while the saturation magnetic moment values and magnetoresistance values were found to decrease. The observed variations in magnetic and magneto-transport properties of the system are explained on the basis of increasing antisite disorder defects and band filling effects induced by electron doping. We have observed the dominant role of band filling in determining the low field magnetoresistance of these systems.     

Superconductivity of Y–Ba–Cu–O and substituted systems

Superconductivity of Y-Ba-Cu-O system is studied in the composition 2:2:3 and 1:2:3 of Y:Ba:Cu. The effect of replacement of Y or Ba by divalent Sr and Ca, trivalent Ce and tetravalent Zr is studied. X-ray diffraction, SEM and TEM techniques are used for materials characterization. Superconducting transition temperatures are measured resistively. Rapid resistance drop observed above 230 K in Y-Ba-Sr-Cu-O and Y-Ba-Ca-Cu-O systems indicate the possible existence of superconductivity above 230 K. Substitution of Ce in place of Y is found to reduce the onset Tc from 95 K to 80 K. For the first time, replacement of Cu by Zr in Y-Ba-Cu-O has yielded the onset Tc of about 105 K.