Effect of Fiber Surface Modification on the Interfacial and Mechanical Properties of Kenaf Fiber-Reinforced Thermoplastic and Thermosetting Polymer Composites

The surfaces of kenaf fibers were treated with three different silane coupling agents. 3-glycidoxypropyltrimethoxy silane (GPS), 3-aminopropyltriethoxy silane (APS), and 3-methacryloxypropyltrimethoxy silane (MPS). Among them, the most effective one for the property improvement was GPS when it was applied to the kenaf fiber surfaces at 0.5 wt%. Thermoplastic polypropylene (PP) and thermosetting unsaturated polyester (UPE) matrix composites with chopped kenaf fibers untreated and treated at different GPS concentrations from 0.1 wt% to 5 wt% were fabricated using compression molding technique. The present study demonstrates that the interfacial, flexural, tensile, and dynamic mechanical properties of both kenaf/PP and kenaf/UPE composites importantly depend on the GPS treatments done at different concentrations. The greatest property improvement of both thermoplastic and thermosetting polymer composites was obtained with the silane treatment at 0.5 wt% and the mechanical properties were comparable with E-glass composites prepared the same polymer matrix under the corresponding fiber length and fiber loading. The results also agreed with each other with regard to their interfacial shear strength, flexural properties, tensile properties, storage modulus, with support of fracture surfaces of the composites.     

Effect of surface treatment on sand erosion behavior of glass beads-filled epoxy resin

Effects of the adhesion between filler particle and matrix on the erosion rate were studied in cured epoxy resin filled with glass beads having mean diameter 17 um. In order to observe the effect of adhesion on erosion rate. the filler particles were treated with silane coupling agent, silicone oil and washed by acetone as well. The filler content of the specimen was varied and also the specimens were attacked by different size angular particles. The comparison of each type of specimen shows that by using acetone and silicone oil for surface treatment, the erosion rate is relatively high. Whereas the specimen in which the filler was treated by silane have low erosion rate. The difference of erosion behavior is influenced by impacting particle size and filler content. Using small impacting particles and also low filler content, the erosion behavior between silane and acetone treated was quite different. On the other hand, using large impacting particles and high filler content, the erosion behavior between them was similar.     

Filler treatment effects on the weathering of talc-, CaCO3- and kaolin-filled polypropylene hybrid composites

Talc, calcium carbonate (CaCO₃), and kaolin hold considerable promise in the development of polymer composites for good mechanical properties and stability. Comparative studies on the usage of these minerals as single fillers in polypropylene (PP) have shown varying degrees of reinforcement due to their differences in terms of particle geometry, surface energy and affinity towards the matrix polymer. In this study, comparisons were made in terms of mechanical, thermal and weatherability properties between hybrid-filler PP composites (i.e. PP filled with either talc–CaCO₃ or talc–kaolin hybrid filler combinations), with particular attention directed towards the effect of surface modification of the fillers. The talc/CaCO₃ hybrid composites have shown exceptional performance in terms of flexural and impact properties. The contribution of talc in the talc–kaolin hybrid composite system has been significant in terms of enhancing the overall tensile and flexural properties. The ability of silane and titanate coupling agents in boosting the resistance of the composites to severe damage and degradation due to natural weathering has been shown.     

Discontinuous basalt and glass fiber reinforced PP composites from textile prefabricates: effects of interfacial modification on the mechanical performance

Spun and blown basalt fibers and their PP matrix composites were investigated. The composites were manufactured by hot pressing technology from carded and needle punched prefabricate using PP fiber as matrix material. Glass and blown basalt fibers were treated with reaction product of maleic acid-anhydride and sunflower oil while spun basalt fibers had a surface coating of silane coupling agent. Fibers were investigated with tensile tests while composites were subjected to static and dynamic mechanical tests. The results show that blown basalt fibers have relatively poor mechanical properties, while spun basalt fibers are comparable with glass fibers regarding geometry and mechanical performance. The static and dynamic mechanical properties of glass and spun basalt fiber reinforced composites are similar and are higher than blown basalt fiber reinforced composites. Results were supported with SEM micrographs.     

Nonisothermal Crystallization Kinetics and Microhardness of PP/CNT Composites

The nonisothermal crystallization kinetics and microhardness of nanocomposites consisting of a polypropylene matrix (PP) and carbon nanotube filler (CNT) have been investigated. Three types of PP matrixes have been used: two of them are nonfunctionalized PP that differ slightly in their melt flow index, whereas the third is grafted with maleic anhydride (MA). Ozawa formalism has been used to study the nonisothermal crystallization kinetics. The results show that the CNT filler has a nucleation role in the nonisothermal crystallization of PP. For all nanocomposites, the nonisothermal crystallization rate increases up to 4% CNT and then decreases slightly or remains almost constant at the higher filler content. This fact has been interpreted in terms of an aggregation of the particles at high filler concentration, which leads to a decrease of the nucleation ability of the filler because the number of heterogeneous nuclei decreases. The crystallization mechanism of the PP matrixes almost does not change in the presence of the CNT filler. The microhardness of the two nonfunctionalized PP increases when the filler content increases and then remains constant above a certain filler content. The experimental microhardness values of the composites based on the functionalized PP are lower than those of the corresponding calculated additive values. The decrease of the creep constant with the filler addition is not significant, as should be expected when inorganic filler is added to a polymer matrix. This is due to the very fine dispersion of the fillers into the polymer matrix at the nanoscale level.     

基于FTIR与XRD的改性脱硫灰取代部分炭黑 制备复合橡胶的补强机理研究

脱硫灰是半干法脱硫的主要副产品,其利用难度大且成本高,导致大量脱硫灰以直接堆放和填埋的方式处理,不但造成环境污染,而且浪费潜在资源。炭黑(8 000 元·t-1)与白炭黑(6 000 元·t-1)是常用的橡胶补强填料,生产工艺繁杂,消耗大量能源和资源,导致成本较高。面对上述问题,如何利用脱硫灰开发一种价格低廉的无机橡胶补强填料,既是固体废弃物高附加值利用的重要途径之一,也是橡胶企业大幅降低填料成本提高经济效益的重要途径之一。由于脱硫灰属于无机材料,橡胶属于有机材料,为了更好的降低脱硫灰界面与橡胶界面(无机界面/有机界面)的不相容性,需要对脱硫灰进行化学改性处理,以提高脱硫灰代替部分炭黑制备橡胶的力学性能。该研究创新性以硅烷偶联剂Si69、硅烷偶联剂KH550与脱硫灰制备改性脱硫灰,然后以改性脱硫灰取代部分炭黑制备复合橡胶。根据国家与行业标准测试复合橡胶的力学性能,如拉伸强度、撕裂强度和硬度。利用扫描电子显微镜(SEM)对复合橡胶的微观形貌进行测试与分析,傅里叶变换红外光谱仪(FTIR)对改性脱硫灰的组成结构进行测试与分析,X射线衍射仪(XRD)对改性脱硫灰的矿物组成进行测试与分析,以揭示硅烷偶联剂Si69与硅烷偶联剂KH550协同对脱硫灰的改性机理,以及改性脱硫灰对复合橡胶的补强机理。结果表明：采用硅烷偶联剂KH550与硅烷偶联剂Si69协同改性脱硫灰,其取代炭黑的增强效果最佳,即复合橡胶的拉伸强度为20.36 MPa、撕裂强度为45.71 kN·m-1和邵尔A硬度为66;硅烷偶联剂KH550与硅烷偶联剂Si69协同改性脱硫灰,不仅保持脱硫灰依然良好的碱性,有利于对复合橡胶起到增强效果;而且可以改善脱硫灰的表面特性与结构,提高改性脱硫灰与丁苯橡胶的无机界面/有机界面相容性。     

Effects of Rice Husk Derived Amorphous Silica on the Thermal-Mechanical Properties of Unsaturated Polyester Composites

Rice husk is rich in amorphous silica which has found various applications as a filler in rubbers and plastics. In the research described here silica was extracted from rice husk ash in the form of sodium silicate which was used to produced amorphous precipitated silica (PS) and silica aerogel (SA) using a sol – gel process and supercritical drying. These materials were then physically mixed with unsaturated polyester (UP) resin and cured at room temperature to form polymer composites. The experimental results showed that the UP composites with 30% (volume percent) of SA filler had lower density and better thermal insulation than the composites with the same amount of PS. Thermogravimetric analysis (TGA) results showed that the T_onset of the PS and SA composites were slightly delayed by 15 and 10°C, respectively. The tensile stress-strain curves showed that addition of the fillers reduced the tensile strength, but increased the elastic moduli of the UP matrix. PS filled UP composites exhibit higher moduli (higher stiffness) than that of SA filled UP composites. This was due to agglomeration and poor adhesion of the SA particles to the UP matrix while better dispersion was observed for the PS filled composite.     

Short sisal fiber reinforced polypropylene composites: the role of interface modification on ultimate properties

Sisal fibers have been used for the reinforcement of polypropylene matrix. The compatibilization between the hydrophilic cellulose fiber and hydrophobic PP has been achieved through treatment of cellulose fibers with sodium hydroxide, isocyanates, maleic anhydride modified polypropylene (MAPP), benzyl chloride and by using permanganate. Various fiber treatments enhanced the tensile properties of the composites considerably, but to varying degrees. The SEM photomicrographs of fracture surfaces of the treated composites clearly indicated the extent of fiber–matrix interface adhesion, fiber pullout and fiber surface topography. Surface fibrillation is found to occur during alkali treatment which improves interfacial adhesion between the fiber and PP matrix. The grafting of the fibers by MAPP enhances the tensile strength of the resulting composite. It has been found that the urethane derivative of polypropylene glycol and cardanol treatments reduced the hydrophilic nature of sisal fiber and thereby enhanced the tensile properties of the sisal–PP composites, as evident from the SEM photomicrographs of the fracture surface. The IR spectrum of the urethane derivative of polypropylene glycol gave evidence for the existence of a urethane linkage. Benzoylation of the fiber improves the adhesion of the fiber to the PP matrix. The benzoylated fiber was analyzed by IR spectroscopy. Experimental results indicated a better compatibility between benzoylated fiber and PP. The observed enhancement in tensile properties of permanganate-treated composites at a low concentration is due to the permanganate-induced grafting of PP on to sisal fibers. Among the various treatments, MAPP treatment gave superior mechanical properties. Finally, experimental results of the mechanical properties of the composite have been compared with theoretical predictions.     

Investigation on Properties of Polypropylene/Multi-walled Carbon Nanotubes Nanocomposites Prepared by a Novel Eccentric Rotor Extruder Based on Elongational Rheology

The properties of polymer matrix composites are related not only to the chemical composition of the materials but also to the processing equipment used for their preparation which has a direct influence on the microstructure of the composites. In this paper polypropylene (PP)/multi-walled carbon nanotubes (MWCNTs) nanocomposites were prepared by melt blending through a self-developed, eccentric rotor extruder (ERE). The structure and elongational deformation mechanism of an ERE were described in detail. The morphological, rheological, thermal and mechanical properties of the resulting PP/MWCNTs nanocomposites were investigated. Scanning electron microscopy (SEM) and rheological analysis showed that the MWCNTs were well dispersed in the PP matrix. The thermal stability was investigated by thermogravimetric analysis (TGA) and indicated that the addition of MWCNTs could effectively improve the thermal stability of pure PP. The percentage of crystallinity and tensile strength of the composites were improved as a result of the heterogeneous nucleation effect of the MWCNTs in the PP matrix. The research results revealed that the enhancement of the properties of PP/MWCNTs composites could be attributed to a better dispersion of the MWCNTs in the matrix as compared to samples prepared by conventional extrusion.     

Effect of Surface Structure of Nano-CaCO3 Particles on Mechanical and Rheological Properties of PVC Composites

To study the effect of different surface structures on resultant mechanical and rheological properties, nano-CaCO₃ particles were treated with isopropyl tri-stearyl titanate (H928), isopropyl tri-(dodecylbenz-enesulfonyl) titanate (JN198), and isopropyl tri-(dioctylpyrophosphato) titanate (JN114). Scanning electron microscopy (SEM) and dynamic mechanic analysis (DMA), carried out to characterize the effective interfacial interaction between the nano-CaCO₃ particles and a poly(vinyl chloride) (PVC) matrix, indicated that JN114 treated nano-CaCO₃ particles had the strongest interfacial interaction with a PVC matrix, while H928 treated nano-CaCO₃ had the weakest. The rheological and mechanical properties of PVC/nano-CaCO₃ composites were investigated as a function of surface structure and filler volume fraction. The tensile yield stress and elongation at break decreased with the increasing of calcium carbonate content while tensile modulus increased. PVC filled with JN114 treated nano-CaCO₃ had the highest tensile modulus and tensile yield stress, while those filled with H928 treated nano-CaCO₃ had the highest elongation at break at the same filler content. The impact strength of PVC/nano-CaCO₃ composites increased with the increasing of CaCO₃ content, and PVC composites filled with JN198 treated nano-CaCO₃ particle had a higher impact strength than those with JN114 or H928 treated, with the value reaching 23.9 ± 0.7 kJ/m² at 11 vol% CaCO₃, four times as high as that of pure PVC. Rheological properties indicated that a suitable interfacial interaction and a good dispersion of inorganic filler in a PVC matrix could reduce the viscosity of PVC/nano-CaCO₃ composites. The interfacial interaction was quantitatively characterized by semiempirical parameters calculated from the tensile strength of PVC/nano-CaCO₃ composites to confirm the results from the SEM and DMA experiments.     

Insights into the Reinforcement of Butyl Rubber by Carbon Black and Silica with the Aid of Their Dynamic Properties

Carbon black (N234) and silica (Vulksail N) with a silane coupling agent Si-69 were chosen as reinforcing fillers in butyl rubber (IIR). The rheological behavior of the IIR compounds and the dynamic mechanical properties of IIR vulcanizates were investigated with a rubber processing analyzer and dynamic mechanical analysis (DMA) to examine the filler dispersion in the rubber matrix and the interaction between filler and matrix. The data indicated that the N234 filled IIR compounds had more filler networks than those filled with silica. Filler networks first appeared at 30 phr N234 and 45 phr silica with silane coupling agent Si-69. The interaction between N234 and IIR was far stronger than that between silica and IIR. However, the silica Vulksail N filled IIR had better wet-grip and lower rolling resistance compared to the carbon black-filled IIR should IIR be chosen as a substitute of styrene-butadiene rubber (SBR) in tire tread. The reinforcing factor, R, R (related to the difference in tan d peak height at T_g for the filled and nonfilled rubbers), also demonstrated that the N234-IIR interaction was stronger than for the silica. IIR with 30 phr N234 exhibited the largest tensile strength, 20.1 MPa, for those vulcanizates examined. The tensile and tear strengths of N234 filled IIR were higher than those of IIR with similar amounts of silica. Thus, it was concluded that N234 is a more active reinforcing filler in IIR than silica (Vulksail N) even with a silane coupling agent (Si-69).     

Effect of the shape of filler particles on the strength of a polymer composite

When metallic or polymeric powder fillers are introduced into poly(2,6-dimethyl-1,4-phenyleneoxide) (PDPO), the strength of the filled composites is found to decrease, while when glass or polymeric fiber fragments are introduced into PDPO, the effect is reverse. The fracture activation energy of the composites is shown to coincide with the fracture activation energy of PDPO. The variation of the strength is caused by the dependence of structure-sensitive parameter γ of the matrix on the concentration and shape of filler particles. On the one hand, filler particles are stress concentrators and their introduction decreases the strength. This effect prevails in the composites filled by spherical particles. On the other hand, when anisotropic particles are introduced, matrix molecules are arranged parallel to their axis, which decreases γ and increases the strength. This effect is predominant in the composites filled by fiber fragments.     

The role of interface modification on the mechanical properties of injection-moulded composites from commingled polypropylene/banana granules

Commingled polypropylene (PP)/banana granules were fabricated from slivers by mixing PP fibers and banana fibers by textile equipment. By twisting the sliver, the reinforcing fibers were compacted and bonded with the molten matrix material. PP/banana composites were prepared from commingled PP/banana granules by injection moulding method with special reference to the effect of maleic anhydride modified polypropylene (MAH-PP) concentration. The mechanical properties of the composites were found to depend on the concentration of MAH-PP. The tensile and flexural properties of the composites increased with the addition of MAH-PP up to 2 wt%. After 2 wt% addition of MAH-PP, these properties tend to be stabilized. On the other hand the unmodified composites showed the maximum impact strength. Fourier transform infrared spectroscopic (FTIR) analysis of the MAH-PP modified composites showed evidence of a chemical bridge between the hydroxyl group of the banana fiber and maleic anhydride of the MAH-PP through an esterification reaction. The feature peak of the esterification occurred in the range ～ 1743 cm^?1. In order to confirm the esterfication reaction further, FTIR spectra of the banana microfibrils and MAH-PP modified PP/banana microfibril composites were taken and compared. The tensile fracture surfaces of the unmodified and MAH-PP modified PP/banana composites were studied by scanning electron microscopy (SEM). An improvement in adhesion between the fiber and the matrix was observed in the case of MAH-PP modified composites. Two different processing methods, both injection and compression mouldings were performed to prepare the PP/banana composites. Tensile properties of the composites prepared by these two methods were compared. The enhancement of tensile properties for injection-moulded composites compared to the compression-moulded composites is owing to the occurrence of orientation, better mixing and interaction between the fiber and the matrix during injection moulding. Finally, experimental results of the tensile properties of the injection-moulded composites have been compared with theoretical predictions.     

Influence of Fiber Surface Treatment on Mechanical Properties of CF/PET Composites

Carbon fiber (CF) / poly (ethylene terephthalate) (PET) composites were prepared with various contents (2–15wt%) of short carbon fibers. To investigate the effect of surface treatment of the CF on the mechanical properties of the composites, three specimens were prepared; those with short carbon fibers (called SCF), short carbon fibers oxidized with nitric acid (called NASCF) and the fibers oxidized with nitric acid and treated with silane coupling agent (called SCSCF). Flexural, tensile and impact tests were performed to observe mechanical behavior of the specimens. The morphology of the specimens was also studied with a scanning electron microscope (SEM). SCSCF composite had better mechanical properties than the other composites with the same content of carbon fibers since the coupling agent resulted in better interfacial adhesion between the fiber and the matrix.     

Interfacial modification for controlling silica–polysiloxane interactions and bonding in some elastomeric composites

Silica reinforcing fillers were generated using the sol-gel approach and their surfaces were modified using either a vinyl alkoxysilane (to provide permanent bonding to a host poly(dimethylsiloxane) elastomer), or a hemiacetal ester (to provide bonding that could be thermally ruptured). The surface areas of the fillers were measured by nitrogen absorption, and their morphologies, interfacial structures, and crosslinking to the elastomer were characterized by ultra small angle and small angle X-ray scattering, scanning electron microcopy, and Fourier-transform infrared spectroscopy. Increasing the amount of the silane coupling agent decreased silica domain sizes, with corresponding increases in surface area and stronger filler-polymer interactions. Vinyltrimethoxysilane had a larger effect than vinylmethyldimethoxysilane. The tensile moduli, tensile strengths, and degrees of toughness of the composites were determined using stress-strain measurements in elongation, both under near-equilibrium conditions and under continuous extension. The permanently bonded modifications gave composites with improved mechanical properties. Rupturing the hemiacetal ester bonding at 120-150°C gave some increase in ultimate stress, maximum elongation, and toughness, thus underscoring the importance of interactions or 'networking' between filler particles.     

Effect of surface treatment on mode I interlaminar fracture behaviour of plain glass woven fabric composites: Part I. Report of the 2nd round-robin test results

A round-robin test programme has been carried out to characterise the mode I interlaminar fracture behaviour of E-glass woven fabric reinforced vinyl ester matrix composites. Special emphasis has been placed on the effect of silane coupling agent on the stability of interlaminar crack propagation and fracture toughness. Sixteen laboratories participated in this programme. Each laboratory was supplied with composite laminates of thicknesses of its own choice and conducted the tests according to its own procedures. The results showed that variations in interlaminar fracture toughness between laboratories were very large in spite of slight differences in the test procedures used, such as specimen dimensions, test speed and data reduction schemes. Nevertheless, the general trends were clearly identified with respect to different silane coupling agents. Other observations and the implications are discussed.     

Fracture of composites based on polyethylene and elastic particles

The composites based on low-density polyethylene with elastomer filling particles are studied. A fracture mechanism induced by the fracture of filler particles or their separation from the matrix polymer is revealed. The fracture of the composites is caused by the growth of formed rhombic pores. The natural relative elongation in a neck is shown to be an important characteristic of a polymer. If the relative elongation in a neck is lower than the strain of appearance of rhombic pores, they form at the stage of uniform tension after necking, and the composite remains plastic. If the relative elongation in a neck is higher than the strain of formation of rhombic pores, they nucleate during necking, and the material undergoes quasi-brittle fracture. Good adhesion between the matrix polymer and elastic particles hinders the appearance of rhombic pores in a neck and, thus, retains high deformation properties of the composites.     

Taguchi approach for characterization of three-body abrasive wear of carbon-epoxy composite with and without SiC filler

Fiber–matrix interfacial bonding plays a critical role in controlling performance properties of polymer composites. Carbon fibers have major constraints of chemical inertness with the matrix and need the surface treatment to improve the adhesion with the matrix. In this work, parametric appraisal of three-body abrasive wear behavior was presented for silane treated carbon fabric reinforced epoxy (C-E) composites with and without silane treated silicon carbide (SiC) as filler. The fiber content was fixed at 60?wt.%, while the weight fraction of SiC was varied (5 and 10?wt.%) to obtain three different compositions. Three-body abrasive wear tests were conducted using design of experiments approach based on Taguchi’s orthogonal arrays. The findings of experiments indicate that the wear loss is greatly influenced by load and grain size of abrasive. An optimal parameter combination was determined, which leads to maximization of abrasion resistance. Inclusion of SiC filler reasonably increased the abrasion resistance of C-E composite. Analysis of variance results showed that the load significantly influenced the abrasion of SiC filled C-E composites. Efforts were also made to correlate the abrasive wear performance of SiC filled C-E composites using artificial neural network (ANN). The wear behavior of composite by ANN prediction closely matched the experimental results and finally, optimal wear settings for minimum wear were identified.     

Composites from Brazilian natural fibers with polypropylene: mechanical and thermal properties

Brazil has a well established ethanol production program based on sugarcane. Sugarcane bagasse and straw are the main by-products that may be used as reinforcement in natural fiber composites. Current work evaluated the influence of fiber insertion within a polypropylene (PP) matrix by tensile, TGA and DSC measurements. Thus, the mechanical properties, weight loss, degradation, melting and crystallization temperatures, heat of melting and crystallization and percentage of crystallinity were attained. Fiber insertion in the matrix improved the tensile modulus and changed the thermal stability of composites (intermediary between neat fibers and PP). The incorporation of natural fibers in PP promoted also apparent T _c and ΔH _c increases. As a conclusion, the fibers added to polypropylene increased the nucleating ability, accelerating the crystallization process, improving the mechanical properties and consequently the fiber/matrix interaction.     

Mechanical and Thermal Properties of Polypropylene/Silica Aerogel Composites

Polypropylene (PP) composites including various amounts of silica aerogel (SA) microparticles were prepared by melt mixing in an internal mixer. The morphology and microstructure of the prepared composites were investigated by scanning electron microscopy (SEM). Mechanical properties of the samples, including elastic modulus, tensile stress, elongation and stress at break, were measured by tensile tests. In addition, the other mechanical features, including Izod impact strength, hardness and wear resistance, were evaluated and then related to the structure of the PP/SA composites. Furthermore, the thermal characteristics of the composites, such as heat deflection temperature and thermal stability, were studied by thermal gravimetric analysis (TGA). The SEM photographs indicated the satisfactory SA particles dispersion for the compositions of 1% and 3% but agglomeration of the aerogels at higher SA contents. Since the composites became stiffer, the impact and tensile strength decreased. The addition of the SA to the PP matrix yielded harder samples with lower weight loss and coefficients of friction in wear tests. The TGA evaluations confirmed that the presence of SA promoted and upgraded the thermal stability and heat deflection temperature of PP. The thermal results proved the superior potential of PP as an insulator when the SA particles were added.