Thermodynamics,a suitable reporter in the design of mercury (II) ion selective electrodes

A fully functionalised calix[4]pyrrole derivative, namely, meso-tetramethyl-tetrakis[(diethylthiocarbamoyl)phenoxy] calix[4]-pyrrole, 1 has been synthesised and structurally characterised. Its complexing properties with metal cations in acetonitrile were investigated with particular emphasis on the thermodynamics of these systems. These data and those previously reported for a partially functionalised calix[4]arene based receptor, 5,11,17,23-tetra-tert-butyl[25,27 bis(diethylthiocarbamoyl)oxy]calix[4]arene, 2 were used to, i) further corroborate their use to predict the selectivity coefficients of carrier mediated mercury (II) ion selective electrodes (ISEs) and ii) to obtain approximate stability constant data from selectivity coefficients. The optimum working conditions of both electrodes were determined. It is shown that while the ISE based on 1 is characterised by a wider linear range and a lower mercury (II) detection than the one based on 2, the latter has the advantage of lower interference of other metal cations due to the much lower stability constants of bivalent cations relative to Hg(II). The response characteristics of these electrodes are compared with those found in the literature. SEM micrographs along with EDX spectra of the PVC membranes containing ionophore 1 or 2 unloaded and loaded with Hg(II) are reported.     

Membrane Composition Effects on the Analytical Behavior of Solid Contact Potentiometric Pb2+ Selective Electrodes Based on Diazadibenzo‐18‐crown‐6 Ionophores

The effect of component contents and membrane thickness on the detection limit (DL), slope (m), linear range (LR) and response time (RT) of Pb²⁺ solid contact potentiometric ion selective electrodes (SCISE) based on 4,10‐diaza‐2,3,11,12‐dibenzo‐18‐crown‐6 (1), 4,10‐diaza‐2,3,11,12‐di(4‐tert‐butylbenzo)‐18‐crown‐6 (2) and 4,10‐diaza‐2,3,11,12‐dibenzo‐18‐crown‐6‐N,N′‐di(carboxymethyl) (3) as ionophores was studied by open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) measurements. The use of an intermediate layer of poly(3‐octyl)thiophene between the gold substrate and the selective membrane was explored. SCISE prepared showing the best responses had typical DL, m, LR and RT values of 10^?6 M, 29 mV/dec, 10^?5 to 10^?3 M and 2 minutes.     

Investigation of ion-selective electrodes with neutral ionophores and ionic sites by EIS. I. Theory

Models of an ion selective electrode involving an ionophore and mobile sites in a membrane are proposed. The first model, called the phase boundary potential model, supposed thermodynamic equilibrium; it allows the concentrations of the various species to be calculated. Then, a kinetic model, which takes into account the ionic transfer at the membrane|solution interfaces, was derived. The impedance of the membrane was calculated. It shows that a membrane with nernstian behavior shows only one capacitive loop in the impedance diagram, which is related to the conductivity and dielectric properties of the material of the membrane. Non-nernstian behavior is related to slow ionic transfer at the membrane|solution interfaces or/and transport limitation of the species in the membrane. Finite rate constants of the ionic transfer lead to a capacitive loop in the middle frequency range, whereas finite rate transport leads to a diffusional impedance in the low frequency range.     

Determination of nanomolar concentrations of phosphate in freshwaters using flow injection with luminol chemiluminescence detection

A simple and rapid flow injection (FI) method is reported for the determination of phosphate (as molybdate reactive P) in freshwaters based on luminol chemiluminescence (CL) detection. The molybdophosphoric heteropoly acid formed by phosphate and ammonium molybdate in acidic conditions generated chemiluminescence emission via the oxidation of luminol. The detection limit (3× standard deviation of blank) was 0.03 μg P l⁻¹ (1.0 nM), with a sample throughput of 180 h⁻¹. The calibration graph was linear over the range 0.032–3.26 μg P l⁻¹ (r²=0.9880) with relative standard deviations (n=4) in the range 1.2–4.7%. Interfering cations (Ca(II), Mg(II), Ni(II), Zn(II), Cu(II), Co(II), Fe(II) and Fe(III)) were removed by passing the sample through an in-line iminodiacetate chelating column. Silicate interference (at 5 mg Si l⁻¹) was effectively masked by the addition of tartaric acid and other common anions (Cl⁻, SO₄²⁻, HCO₃⁻, NO₃⁻ and NO₂⁻) did not interfere at their maximum admissible concentrations in freshwaters. The method was applied to freshwater samples and the results (26.1±1.1–62.0±0.4 μg P l⁻¹) were not significantly different (P=0.05) from results obtained using a segmented flow analyser method with spectrophotometric detection (24.4±4.45–84.0±16.0 μg P l⁻¹).