首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
A capillary electrophoresis fluorescence detector is described. A high-pressure mercury lamp with a filter block allowed the selection of a particular excitation waveband. Detection was performed on-column, the fluorescence emission was monitored and measured with a silicon photodiode detector with a built-in amplifier. The concentration limit of detection (CLOD) of 0.4 ng/mL was obtained for rhodamine B, a fluorescent indicator. Based on an estimated injection volume of 2.5 nL, the mass limit of detection (MLOD) was 2.1×10–18 mol. The separation of three fluorescent indicators: thionine, eosin yellowish and rhodamine B, was achieved in less than 6 min. The separation of nine porphyrin-free acids using the system developed was also demonstrated. The advantages and potential of using an epi-illumination microscope as a versatile and sensitive fluorescence detection system for capillary electrophoresis are described.  相似文献   

2.
The use of 2-chloro-1-methylquinolinium tetrafluoroborate, an ultraviolet tagging reagent, for the ion-pair, reversed-phase high-performance liquid chromatography of mesna in human plasma is reported. In order to achieve this objective optimization of the two-step procedure, derivatization and separation of mesna S-quinolinium derivative from that of other thiols present in plasma and internal standard, was investigated. The derivatization was optimized in terms of pH, reagent excess and time of the reaction, and the mobile phase in terms of ion-pairing reagent concentration, pH, organic modifier content and temperature. Baseline separation was achieved on an analytical Waters Nova-Pak C18 (150x3.9 mm, 5 microm) column with a mobile phase consisting of pH 2.3 0.05 M trichloroacetic acid-acetonitrile (89:11, v/v) pumped at 1.2 ml/min. The peak height ratios of the mesna derivative to that of the internal standard (thiomalic acid) varied linearly with the concentration of the analyte added to normal plasma with a correlation coefficient of 0.9997. The lower limits of detection and quantitation were 40 pmol/ml (0.8 pmol on-column) and 160 pmol/ml (3.2 pmol on-column), respectively. The intra-run imprecision and inaccuracy were from 1.3 to 2.4 and from 1.3 to 2.0%, respectively.  相似文献   

3.
利用水热合成法在掺杂F的SnO2导电玻璃(FTO)基底上制备TiO2纳米线阵列结构, 与内部萃取电喷雾电离质谱(iEESI-MS)联用, 实现了罗丹明B降解中间产物的检测, 并推测了反应机理. 考察了离子源电压、 离子传输管温度和洗脱剂组成对罗丹明B及其降解产物信号强度的影响. 结果表明, 在光催化反应时间为2 h, 反应溶液体积为15 μL, 离子源电压为3 kV, 离子传输管温度为300 ℃, 洗脱剂为0.5%乙酸-甲醇(体积比)混合溶液条件下, 可以获得最佳的罗丹明B及其中间产物信号. 在优化的条件下, 从罗丹明B反应溶液中共检测出8种中间产物, 基于此推测了罗丹明B的降解机理. 该方法对罗丹明B定量分析的检出限(S/N≥3)为0.1 μg/L, 相对标准偏差(RSD, n=6)为2.1%~7.3%, 具有检测限低、 灵敏度高、 样品耗量少、 分析速度快及操作简便等特点. 此外, 该方法还可用于其它光催化反应中间产物的检测, 拓宽了质谱分析法在环境领域中的应用范围, 为今后环境污染物降解机理的探究提供了新思路.  相似文献   

4.
Six estrogens-estrone, equilin, estradiol, sodium estrone sulphate, sodium equilin sulphate and sodium 17-alpha-dihydroequilin sulphate in dog serum were successfully separated and quantified by a high performance liquid chromatographic method developed in our laboratories. The mobile phase was optimized by studying the effects of an organic modifier (acetonitrile) and an ion pairing reagent (tetrabutylammonium hydroxide). The serum sample work-up procedure was designed to recover both conjugated and unconjugated estrogens. The optimum method involved acetonitrile to precipitate serum proteins/peptides and extract estrogens. Residues were reconstituted in 50% acetonitrile in water for injection. The detection limits for these six estrogens via UV detection ranged from 0.5 to 5 ng on-column with a signal-to-noise ratio (S/N) of 10 for a 20 microL injection and via fluorescence 0.1 ng on-column for 17-beta-estradiol. Validation data are included for all six estrogens.  相似文献   

5.
Multipumping (MPFS) and multicommuted (MCFS) flow systems relying on pulsed and laminar flows were critically compared. The mixing conditions and dispersion associated with both systems were evaluated by simulating the sample with bromocresol green. The molybdenum blue method for phosphate determination in soil extracts was also implemented in both flow systems. Furthermore, laser-induced fluorescence (LIF) was applied to visualize the dispersing sample; rhodamine B was used as the fluorescent species. The pulsed flow enhanced the mixing of the solutions involved, thus reducing reagent consumption (48 and 96 microl for MPFS and MCFS), and improving sampling rate (67 and 144 h(-1) for MCFS and MPFS). For phosphate determination, results obtained with both systems were precise (r.s.d. < 0.5%; n = 10) and accurate. Analyses of the absorbance vs time/space LIF plots revealed that exploitation of pulsed flow led to a pronounced radial dispersion and to a limited axial dispersion, typical aspects of turbulent flows.  相似文献   

6.
Wang W  Zhou L  Wang S  Luo Z  Hu Z 《Talanta》2008,74(4):1050-1055
This paper describes a micellar electrokinetic chromatography with indirect laser-induced fluorescence detection method for the simultaneous determination of adenine and guanine in DNA extracts from fungus, maize and soybean. The baseline separation was achieved within 2.5min with running buffer (pH 9.3) composed of 10mM borate, 20mM SDS, 3.0x10(-7)M fluorescein sodium as background reagent, applied voltage of 27.5kV, cartridge temperature of 25.0 degrees C. Good linearity relationships (correlation coefficients>0.9917) between the second-order derivative peak heights (RFU) and concentrations of the analytes (mgml(-1)) were obtained. The detection limits in second-order derivative electrophoregrams were 1.16x10(-3)mgml(-1) for adenine and 0.29x10(-3)mgml(-1) for guanine, respectively. The RSD data of intra-day for migration times and second-order derivative peak heights were less than 0.59 and 4.09%, respectively. This developed method was applied to the analysis of the two purines in DNA extracts with recoveries in the range of 85.3-110.2%. In this work, although the detection sensitivity was lower than that of direct LIF, yet the method has the advantages of rapidness and simplicity. And it would also extend the application range of LIF detector.  相似文献   

7.
《Analytical letters》2012,45(18):2883-2891
A capillary electrophoresis microchip coupled with a confocal laser-induced fluorescence (LIF) detector was successfully constructed for the analysis of trace amounts of heavy metals in environmental sources. A new fluorescence dye, RBPhOH, synthesized from rhodamine B, was utilized in a glass microchip to selectively determine copper with high sensitivity. A series of factors including running buffer concentration, detection voltage, and sample loading time were optimized for maximum LIF detector response and, hence, method sensitivity.  相似文献   

8.
Mercury-pyrrolidinedithiocarbamate complexes are first time used for speciation of aquatic mercury with high-performance liquid chromatographic/ion trap-mass spectrometric method utilizing atmospheric pressure chemical ionization (APCI). The separation of the four mercury species was achieved in less than 5 min with a linear gradient profile of aqueous methanol from 70 up to 100% (v/v) in 4th min, isocratic elution at 100% up to 5th min and followed by a negative gradient to 70% in 6th min. The best separation was achieved on a reverse phase Zorbax Eclipse XDB C18 column (50 mm × 2.1 mm i.d., 1.8 μm particle size). The on-column limits of detection (injection volume 1 μL) were 370 pg for methylmercury (MeHg+), 280 pg for ethylmercury (EtHg+), 250 pg for phenylmercury (PhHg+) and 90 pg for inorganic mercury (Hg2+) when the data were collected in selective ion monitoring (SIM) mode. A method of isolation and preconcentration of the mercury species using a “home-made” C18 solid phase extraction (SPE) microcolumns was developed to enhance sensitivity of the method. The preconcentration factor as much as 2500 was achieved with on-column complex formation of mercury-pyrrolidinedithiocarbamate. Methanol (100%) was chosen for elution of preconcentrated mercury species. The method was applied for the determination of mercury species in river water samples.  相似文献   

9.
We report a new method for the trace analysis of mercury (II) ions in water. The approach involves the use of droplet-based microfluidics combined with surface-enhanced Raman scattering (SERS) detection. This novel combination provides both fast and sensitive detection of mercury (II) ions in water. Specifically, mercury (II) ion detection is performed by using the strong affinity between gold nanoparticles and mercury (II) ions. This interaction causes a change in the SERS signal of the reporter molecule rhodamine B that is a function of mercury (II) ion concentration. To allow both reproducible and quantitative analysis, aqueous samples are encapsulated within nanoliter-sized droplets. Manipulation of such droplets through winding microchannels affords rapid and efficient mixing of the contents. Additionally, memory effects, caused by the precipitation of nanoparticle aggregates on channel walls, are removed since the aqueous droplets are completely isolated by a continuous oil phase. Quantitative analysis of mercury (II) ions was performed by calculating spectral peak area of rhodamine B at 1,647 cm−1. Using this approach, the calculated concentration limit of detection was estimated to be between 100 and 500 ppt. Compared with fluorescence-based methods for the trace analysis of mercury (II) ions, the detection sensitivities were enhanced by approximately one order of magnitude. The proposed analytical method offers a rapid and reproducible trace detection capability for mercury (II) ions in water.  相似文献   

10.
A reversed-phase monolithic silica based capillary column (Onyx C(18), 150 mm x 0.1 mm) was modified with the amphoteric surfactant, N-dodecyl-N,N-(dimethylammonio)undecanoate (DDMAU) and evaluated for the separation and determination of inorganic anions using on-column capacitively coupled contactless conductivity detection (C(4)D). The chromatographic performance of the column was evaluated and under optimal conditions separation efficiencies of 56,200 plates per meter or 7025 plates per column (at detection point) were observed (for iodide). Direct plumbing of the capillary column to the micro-injector and on-column detection eliminated extra-column band broadening, thus allowing accurate analysis of van Deemter curves obtained for the monolithic capillary column. The calculated value for the C-term in the obtained van Deemter curve was between 3 and 4 ms for inorganic anions, allowing for the utilisation of relatively high flow rates without significant losses in efficiency. The performance of the C(4)D detector was investigated and compared for detection on an open tubular capillary column and on the modified monolithic silica capillary column. The on-column detection approach did not result in any significant decrease in peak sensitivity for the monolith compared to responses recorded for open tubular capillary columns, and in addition meant the system could be applied to rapid separations by simple variation in apparent column length. The proposed chromatographic system allowed for detection of common anions at sub-ppm level with a 10 nL injection volume. Additionally, on-column detection allowed visualisation of the development of the separation at any point in time and evaluation of the longitudinal uniformity of the ion-exchange coating.  相似文献   

11.
A solid-phase microextraction (SPME) procedure for the determination of four haloanisoles (2,4,6-trichloroanisole, 2,3,4,6-tetrachloroanisole, pentachloroanisole and 2,4,6-tribromoanisole), as well as their precursor halophenols (2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol, pentachlorophenol and 2,4,6-tribromophenol), involved in the presence of cork taint in wine, was developed. Firstly, analytes were concentrated on a SPME fiber, and then halophenols were derivatised using N-methyl-N-trimethylsilyltrifluoroacetamide (MSTFA). The compounds were desorbed for 5 min in the gas chromatography injector port and then determined with an electron capture detector. The influence of different parameters on the efficiency of extraction (volume of sample, type of fibre coating and time) and derivatisation (time, temperature and volume of MSTFA) steps was evaluated. Polyacrylate (PA) was selected as the extraction fiber, optimised parameters for SPME were 10 ml of wine, temperature 70 degrees C and extraction time 60 min. The optimal conditions identified for the derivatisation step were temperature 25 degrees C, reagent volume 50 microl and extraction time 25 min. Under optimal conditions, the proposed method showed satisfactory linearity, precision and detection limits. The method was applied successfully to the analysis of red wine samples. To our knowledge, this is the first time that headspace (HS) SPME combined with on-fiber derivatisation has been applied to determine cork taint responsible compounds in wine.  相似文献   

12.
This paper describes a novel and sensitive pre-column derivatisation method for the detection and quantitation of beta-lactams and their biosynthetic precursors at trace levels in fermentation media. Filtered broths from fermentations of strains of Penicillium chrysogenum and Cephalosporium acremonium, after deproteination and centrifugation, were incubated with 9-fluorenylmethylchloroformate for 5 min at 20 degrees C in 0.2 M borate buffer at pH 7.7. Following two-fold pentane extraction of the reagent hydrolysis product, the aqueous layer was injected directly onto a C18 reversed-phase column, and products were detected spectrofluorimetrically with excitation and emission wavelengths of 260 and 313 nm, respectively. Detection limits of 0.01 and 0.05 micrograms ml-1 were achieved for both 6-aminopenicillanic acid (6-APA) and isopenicillin N in borate buffer and filtered fermentation broths, respectively, using a 10-microliter injection volume. A linear calibration for 6-APA in fermentation broth was obtained for a very wide concentration range (0.05-100 micrograms ml-1). Detection limits for solutions of cephalosporin C, deacetylcephalosporin C and deacetoxycephalosporin C in broth were all 0.25 micrograms ml-1. The detection limit for the beta-lactam precursor delta-(L-aminoadipyl)-L-alpha-cysteinyl-D-valine (ACV) dimer in borate buffer was 0.5 microgram ml-1. The cephalosporins and ACV dimer gave linear plots in the ranges 3-25 and 1-100 micrograms ml-1, respectively. Repeated analysis of 6-APA at a concentration of 10 micrograms ml-1 in filtered broth gave a mean peak area of 2.5.10(6) with a standard deviation of 2.6.10(5) using a 10-microliter injection volume. Ampicillin spiked into deproteinated blood serum gave a linear calibration in the concentration range 2-100 micrograms ml-1.  相似文献   

13.
This paper describes a cost-effective procedure for the analysis of short-chain aliphatic amines in water samples using a solid-phase microextraction device. Analyte preconcentration and derivatisation were effected into a capillary column coated with 95% polydimethylsiloxane–5% polydiphenylsiloxane, which was used as the injection loop of a Rheodyne injection valve. The coating was previously loaded with the derivatisation reagent, 9-fluorenylmethyl chloroformate. A volume of 1 mL of samples was then drawn into the capillary column, and the extracted analytes were left to react on the capillary coating for 5 min. Next, the capillary column was cleaned by passing water. Finally, the injection valve was rotated, and the derivatives formed were dynamically desorbed and transferred to the analytical column into the mobile phase. Methylamine, ethylamine, propylamine, n-butylamine and n-pentylamine were selected as model compounds. Excellent sensitivity was achieved, being the limits of detection of 15–200 μg/L when using UV detection and of 0.1–0.4 μg/L by fluorescence.  相似文献   

14.
An on-column immunological reaction was employed to achieve simple and rapid analysis in an immunoassay based on capillary electrophoresis using semiconductor laser-induced fluorescence detection. Human serum albumin (HSA) labeled with sulfoindocyanine succinimidyl ester (Cy5), a fluorescent compound with an absorption maximum at 649 nm, was used as a fluorescent probe for the immunoassay. In a binding assay, with anti-HSA as the analyte molecule, Cy5-HSA was injected in a capillary column followed by the injection of anti-HSA so as to form individual zones. By applying a potential, the anti-HSA reacted with Cy5-HSA at the boundary between Cy5-HSA and anti-HSA zones, since anti-HSA has a higher electrophoretic mobility than Cy5-HSA. Furthermore, the on-column method enhances the sensitivity by injecting a large volume of the sample. Free Cy5-HSA and its immunocomplex with anti-HSA were separated with less degradation in resolution than that predicted from the injection time of anti-HSA, even when the injection time for anti-HSA was increased. The ratio of the peak area of the complex to that of the total Cy5-HSA (free Cy5-HSA and the complex) increased in proportion to the injection time of anti-HSA. As a result, the detection limit was improved up to eight-fold (the concentration detection limit, 0.007 mg mL(-1), for an injection time of 240 s, compared to that obtained using an off-column sample preparation. Furthermore, the on-column reaction method was applicable to an immunoassay to determine native HSA, in which native HSA and Cy5-HSA react with anti-HSA stepwise. The detection limit in the stepwise reaction immunoassay was 0.005 mg mL(-1), which is 14 times lower than that in an off-column method, with the analysis time less than 10 min as the result of increasing the injection time of native HSA. In addition, the present on-column immunoassay was applied to the sample containing a high concentration of salts for investigating the effect of salts in the sample solution.  相似文献   

15.
A method for the analysis of type A trichothecenes T-2 toxin, HT-2 toxin, neosolaniol and diacetoxyscirpenol by high-performance liquid chromatography with fluorescence detection using coumarin-3-carbonyl chloride has been developed. Different parameters concerning the analytical procedure such as stability of both the reagent and derivatised analytes, time and temperature of the derivatisation reaction, were studied and optimised. Three different clean-up procedures (solid-phase extraction with silica gel or C-18 cartridges, and liquid–liquid partition between toluene and dihydrogen phosphate buffer) were tested in order to remove the excess reagent peaks. The last procedure gave the best results when the buffer pH was 3–5.5, and is therefore recommended. Separations were performed on a stainless steel LiChrospher 100 C-18 reversed-phase column with pre-column of the same phase. The mobile phase was acetonitrile/water (65:35, v/v) containing 0.75% acetic acid at a flow-rate of 1.0 ml/min. The proposed method provides good separation between the four trichothecenes and good reproducibility (RSD of calibration standards <5%). The limits of detection of the studied trichothecenes at a signal-to-noise ratio of 3:1, with an injection volume of 20 μl were 10 ng/g sample for T-2 toxin and about 15 ng/g sample for the remaining mycotoxins. The calibration curve was linear between 10 and 2000 ng for the four trichothecenes assayed. The method was applied to the analysis of these mycotoxins in fungal cultures (corn and rice) of Fusarium sporotrichioides, and is also perfectly suitable for the quantification of type A trichothecenes in contaminated cereals.  相似文献   

16.
A new water‐soluble reagent, rhodamine B piperazinoacetohydrazine (RBPH), with improved spectroscopic and reaction properties, has been developed and characterized for pyruvic acid labeling. The reagent RBPH is designed and synthesized by using rhodamine B as a spectroscopic unit, and hydrazine as a carbonyl‐specific labeling unit; the two units are connected by a well‐chosen linker of piperazine, which prohibits the formation of the nonfluorescent spirocyclic structure of rhodamine B, thereby keeping the spectroscopic response of the reagent in a stable state. Such a design enables RBPH not only to maintain its excellent spectroscopic properties over a wide pH range, but also to exist as a stable cation with high water solubility. Moreover, the hydrazino group of RBPH is expected to react selectively with carbonyl compounds under mild conditions through the rapid formation of hydrazones. These important features make RBPH of great potential use in the labeling of aldehydes or ketones in various biosystems, and such an application of RBPH as a precolumn derivatizing reagent has been successfully demonstrated on the analysis of pyruvic acid in human serum by high‐performance liquid chromatography with common UV/Vis detection.  相似文献   

17.
This article describes a further development of our previously reported miniaturized analysis system of microchip electrophoresis with on‐line chemiluminescence detection. The system, developed first time for nonaqueous microchip electrophoresis with peroxyoxalate chemiluminescence detection, consists of a suction pressure device for sample or reagent introduction, a constant voltage supplied for electrophoretic separation, an either hydrophilic or hydrophobic porous polymer plug for preventing chemiluminescence reagent flowing upstream and a spiral detection channel for enhancement of both detection sensitivity and reproducibility. Especially, by using organic solvent as BGE medium, the developed system avoided the interface problem between aqueous running buffer and low‐water‐content chemiluminescence solvent in previous reports. The influencing factors on chemiluminescence signal were optimized using rhodamine 6G as model molecule. The system performance was further investigated in the experiment of separation of hydrophilic rhodamine dyes and analysis of hydrophobic polycyclic aromatic hydrocarbon, providing the detection limit (S/N = 3) of 3.5 nmol/L for rhodamine 123, 6.8 nmol/L for rhodamine 6G, and 60 nmol/L for 1‐aminopyrene, respectively. The experimental results showed the system offered a number of benefits, including compact structure, high sensitivity, good reproducibility, and a wide range of application prospect.  相似文献   

18.
The formation of a pink-coloured product when rhodamine 6G is treated with tetraiodomercurate(II) is used to determine mercury (5–25 μg) in a final volume of 25 ml. The reaction occurs immediately over the pH range 1–7 and, when the system is stabilized with gelatin, the absorbance remains unchanged at 575 nm for at least 24 h. The few interfering ions can be masked by the addition of appropriate reagent solutions. The method is simple and reliable and provides a molar absorptivity of 7.0·104 l mole-1 cm-1.  相似文献   

19.
The new acid hydrazides, 2-(5-hydrazinocarbonyl-2-thienyl)-5,6-methylenedioxybenzofuran (TMBH) and 2-(5-hydrazin-ocarbonyl-2-furyl)-5, 6-methylenedioxybenzofuran (FMBH), were synthesized as precolumn fluorescence derivatisation reagents for carboxylic acids in liquid chromatography. These compounds readily react with carboxylic acids in the presence of a coupling reagent under mild conditions in aqueous solution to give fluorescent derivatives. The detection limits of lauric acid were both 0.1 pmol per 10 μl injection volume at a signal-to-noise ratio of 3. The methods in which these compounds are used were applied to the assay of a standard mixture of prostaglandins (25 μM) and prostaglandins in a human seminal fluid.  相似文献   

20.
采用热解析-高场非对称波形离子迁移谱(FAIMS)技术快速检测柯衣定、 孔雀石绿、 罗丹明B和甲基红4种合成色素. 通过对热解析温度和载气流量进行优化, 确定了不同色素的离子特征信号. 在最佳分析条件下, 热解析温度为160 ℃, 载气流量为1.6 L/min, 采用不同模式下补偿电压(CV)值定性, 以FAIMS在正模式下检测柯衣定(CV=0.41 V)和罗丹明B(CV=-0.89 V), 在负模式下检测甲基红(CV=-0.67 V)和孔雀石绿(CV=0.02 V); 用外标法定量检测了样品中的4种合成色素, 线性关系R2≥0.9967, 检出限为2.5~10 μg/L, 定量限为5~20 μg/L, 加标回收率≥78.2%, 相对标准偏差RSD≤8%. 本文为FAIMS技术快速检测合成色素提供了一定的技术基础.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号