Chemical synthesis of Ni/TiO<Subscript>2</Subscript> nanophotocatalyst for UV/visible light assisted degradation of organic dye in aqueous solution

The Ni/TiO₂ nanoparticles with different Ni dopant content were prepared by a modified sol–gel method. The structure and photoinduced charge properties of the as-prepared catalysts were determined using X-ray diffraction, transmission electron microscopy, UV–vis diffuse reflectance spectroscopy and surface photovoltage spectroscopy techniques, and the photocatalytic efficiency of these catalysts was tested using an organic dye. It was shown that Ni modification could greatly enhance the photocatalytic efficiency of these nanocomposite catalysts by taking the photodegradation of methyl orange as a model reaction. With appropriate ratio of Ni and TiO₂, Ni/TiO₂ nanocomposites showed the superior photocatalytic activity than the single TiO₂ nanoparticles. Surface photovoltage spectra demonstrated that Ni modification could effectively inhibit the recombination of the photoinduced electron and holes of TiO₂. This electron–hole pair separation conditions are responsible for the higher photocatalytic performance of Ni/TiO₂ nanocomposites in the visible region of electromagnetic spectrum.     

Synthesis,characterization of B-doped TiO<Subscript>2</Subscript> nanotubes with high photocatalytic activity

B-doped TiO₂ nanotubes (B/TiO₂ NTs) were prepared by the combination of sol–gel process with hydrothermal treatment. The prepared catalysts were characterized by XRD, TEM and XPS. The photocatalytic activity of B/TiO₂ NTs was evaluated through the photodegradation of aqueous methyl orange. The results demonstrated that the 1.5% B/TiO₂ NTs calcined at 300 °C possessed the best photocatalytic activity. Compared with pure TiO₂ nanotubes, the doping with B significantly enhanced the photocatalytic efficiency.     

Fabrication,characterization, and photocatalytic performance of TiO<Subscript>2</Subscript> hybridized with SiO<Subscript>2</Subscript>

Nanostructures TiO₂–SiO₂ photocatalysts were successfully synthesized using the sol-gel method, hydro-calcination, co-precipitation and room-temperature solid-phase synthesis technology. X-ray powder diffraction pattern (XRD), Fourier transform infrared spectrum (FTIR), photoluminescence (PL) spectra, thermal analyses (TG–DTA), scanning electron micrographs (SEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectroscopy (UV-Vis DRS) were used to characterize the as-synthesized catalysts. Photocatalytic performances of the catalysts were evaluated by the degradation of methyl orange (MO) under s imulated natural light and the degradation rate of MO is 97.2%. The composites showed a good stability: after five recycling runs there are no significant decreases in the photocatalytic activity. The photodegradation of methylene blue, rhodamine B, methyl violet, naphthol green B, basic fuchsin, malachite green, and methyl red were also tested, and the degradation rate of dyes could reach over 94.2 %. A possible mechanism for the photocatalysis with the TiO₂–SiO₂ was proposed.     

Sol-gel preparation and characterization of Co/TiO<Subscript>2</Subscript> nanoparticles: Application to the degradation of methyl orange

Cobalt doped titania nanoparticles were synthesized by sol-gel method using titanium(IV) isopropoxide and cobalt nitrate as precursors. X-Ray diffraction (XRD) results showed that titania and Co/TiO₂ nanoparticles only include anatase phase. The framework substitution of Co in TiO₂ nanoparticles was established by XRD, scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM-EDX) and Fourier transform infrared (FT-IR) techniques. Transmission electron microscopy (TEM) images confirmed the nanocrystalline nature of Co/TiO₂. The increase of cobalt doping enhanced “red-shift” in the UV-Vis absorption spectra. The dopant suppresses the growth of TiO₂ grains, agglomerates them and shifts the band absorption of TiO₂ from ultraviolet (UV) to visible region. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. Although the photocatalytic activity of undoped TiO₂ was found to be higher than that of Co/TiO₂ under UV irradiation, the presence of 0.5% Co dopant in TiO₂ resulted in a catalyst with the highest activity under visible irradiation.     

Fabrication and photocatalytic property of TiO<Subscript>2</Subscript> nanofibers

TiO₂ nanofibers were prepared from tetrabutyl titanate sol precursors by using electrospun method. X-ray diffraction (XRD) and atomic force microscope (AFM) were used to characterize their crystal structure and morphology feature. The results demonstrated that TiO₂ nanofibers possessed anatase phase and the average diameter of TiO₂ nanofibers was about 150 nm. The photocatalytic property of TiO₂ nanofibers was evaluated for the photodecomposition of methyl orange solution. And TiO₂ nanofibers exhibited high photocatalytic activities with transfer efficiency about 100% after 20 min.     

Coal Combustion Synthesis of Coal Cinder-Supported TiO<Subscript>2</Subscript> with Commendable Photocatalytic Activity

Coal cinder-supported TiO₂ photocatalysts were synthesized via a novel coal combustion method. As-obtained samples were characterized by XRD, SEM, EDS mapping, Raman spectra, FTIR and DRS, and their photocatalytic performances were evaluated by degradation of methylene blue (MB) and methyl orange (MO) under UV–Vis light illumination. The results revealed that mixed-phases TiO₂ with adjustable anatase–rutile ratio could be obtained by adjusting the amount of precursor tetrabutyl titanate, which was uniformly covered on the coal cinder. These coal cinder-supported TiO₂ photocatalysts exhibited commendable photocatalytic activity. Among them, the indexed CCT-7.5 sample presented the maximum of activity, which can be attributed to the optimal phase composition of TiO₂. The present work provided a novel synthetic route to fabricate immobilized photocatalysts, which might be extended to the preparation of other functional materials.     

Effective photocatalytic degradation of an azo dye over nanosized Ag/AgBr-modified TiO<Subscript>2</Subscript> loaded on zeolite

Zeolite-based photocatalysts were prepared by the sol-gel and deposition methods. The photocatalysts were characterised by X-ray diffraction, nitrogen adsorption-desorption isotherms, FTIR spectroscopy, scanning electron microscopy and energy-dispersive X-ray spectrometry. The activity of the prepared photocatalysts was evaluated by the UV-induced degradation of acid blue 92, a textile dye in common use. The effect of various parameters, such as catalyst concentration, initial dye concentration, thiosulphate concentration and pH, on the rate and efficiency of the photocatalytic degradation of acid blue 92 was investigated. The results showed that each parameter influenced the degradation rate and efficiency in a particular way. It was also found that, under optimised conditions, Ag/AgBr/TiO₂/zeolite exhibited the highest photocatalytic performance. A comparison of catalytic activity when exposed to visible light under the same conditions showed that the photocatalysts containing AgBr had the highest activity.     

Plasmon-resonance-enhanced visible-light photocatalytic activity of Ag quantum dots/TiO2 microspheres for methyl orange degradation

We successfully prepared Ag quantum dots modified TiO₂ microspheres by facile solvothermal and calcination method. The as-prepared Ag quantum dots/TiO₂ microspheres were characterized by scanning electron microscope, transmission electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy and UV-vis diffuse reflectance spectroscopy. The Ag quantum dots/TiO₂ photocatalyst showed excellent visible light absorption and efficient photocatalytic activity for methyl orange degradation. And the sample with the molar ratio of 0.05 (Ag to Ti) showed the best visible light photocatalytic activity for methyl orange degradation, mainly because of the surface plasmon resonance (SPR) effects of Ag quantum dots to generate electron and hole pairs for enhanced visible light photocatalysis. Finally, possible visible light photocatalytic mechanism of Ag quantum dots/TiO₂ microspheres for methyl orange degradation was proposed in detail.     

Solvothermal synthesis and photocatalytic activity of S-doped TiO<Subscript>2</Subscript> and TiS<Subscript>2</Subscript> powders

The photocatalytic activity of S-doped TiO₂ powder depends on the S content. To synthesize S-doped TiO₂ powders with high S content, solvothermal processes were used in this work. The S-doped TiO₂ powder contains 2.0 M% sulfur and has an absorption edge of 460 nm (2.7 eV). The pure TiS₂ powder also synthesized by a solvothermal process has an absorption edge of 595 nm (2.08 eV) and broad absorption above 595 nm. The photocatalysis experiments indicate that the degradation of methyl orange is associated with the light adsorption edge. The photocatalytic activity is much larger for the pure TiS₂ powder than for partially S-doped TiO₂ powder.     

On the photocatalytic properties of nano-TiO<Subscript>2</Subscript> with dual-phase structure for aqueous methyl-red dye degradation

Heterogeneous photocatalytic removal of methyl-red (MR) dye from liquid phase was done using mixed-phase nanocrystalline TiO₂ for enhancement its photochemical decomposition capabilities. The mixed-phase nanocrystalline TiO₂ was characterized using various techniques to investigate its physicochemical properties. The photocatalytic efficiency of mixed-phase nanocrystalline titania was explored by monitoring the photochemical decay of aqueous MR dye. The results showed that the as-prepared mixed-phase nanocrystalline TiO₂ was excellent for degradation of MR molecule, and the impurity of rutile form increases the photochemical activity by a by a factor of 3. The reaction mechanism was proposed and the results demonstrate that the photocatalytic oxidation reaction followed a pseudo-first-order kinetics.     

Synthesis of Bi<Subscript>2</Subscript>O<Subscript>4</Subscript>@TiO<Subscript>2</Subscript> Heterojunction with Enhanced Visible Light Photocatalytic Activity

A novel Bi₂O₄@TiO₂ heterojunction was constructed by a simple two-step method. The charges migration between Bi₂O₄ and TiO₂ via the heterojunction improves the electron/hole separation efficiency. Furthermore, Bi₂O₄@TiO₂ heterostructures exhibit better adsorption capability for methyl orange molecular due to their higher specific surface area than pure Bi₂O₄. As a result, Bi₂O₄@TiO₂ hybrids show an improved visible light photocatalytic activity and photostability for the degradation of methyl orange.     

Synthesis and characterization of ZnO-doped cupric oxides and evaluation of their photocatalytic performance under visible light

ZnO–CuO binary oxide photocatalysts were synthesized by the liquid phase coprecipitation method. The catalysts were characterized by X-ray diffraction, transmission electron microscopy and UV–vis spectroscopy. The photocatalytic activity of the ZnO–CuO nanocomposites was estimated on the basis of decoloration of methyl orange dye under visible light. The effects of parameters such as calcining temperature, amount of catalyst and pH on the photocatalytic degradation efficiency of methyl orange solutions were investigated in detail. The maximum photocatalytic activity was obtained on ZnO–CuO nanocomposites with a calcining temperature of 350 °C, using a catalyst amount of 0.056 g/L and a pH of 7.5. The visible light-driven capability of ZnO–CuO nanocomposites is much better than that of commercially available TiO₂ photocatalysts under comparable conditions.     

Impact of synthesis methods on nanosized silver modified titania photocatalysts

This work reports the synthesis and studies on photocatalytic activity of a material based on titanium oxide doped with silver. Two kinds of Ag-deposited TiO₂ were synthesized via soft chemical reduction (SCR) and photodeposition (PD) methods. The structure, composition and chemical properties of the obtained products were investigated by X-ray diffraction, UV-vis diffuse reflectance spectroscopy, photoluminescence spectra and Fourier transformation infrared spectroscopy techniques. The photocatalytic oxidation activity in a course of removal and destruction of organic compounds such as methyl orange dye using Ag/TiO₂ hybrid material was studied. The results suggest that SCR synthesized Ag/TiO₂ exhibited better photocatalytic performance that that obtained by PD method. The relationship between the synthesis method and photocatalytic activity of synthesized Ag/TiO₂ was analyzed with a focus on the plasmonic photocatalysis of silver. When compared to PD method, the SCR produced more homogeneous and smaller silver particles with a better dispersion than photodeposition that results in a relative increase of material activity in the photocatalytic degradation of dye pollutant.     

Catalytic Properties of TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles in Plasma Chemical Treatment

We proposed here a new process coupling dielectric barrier discharge (DBD) plasma with magnetic photocatalytic material nanoparticles for improving yield in DBD degradation of methyl orange (MO). TiO₂ doped Fe₃O₄ (TiO₂/Fe₃O₄) was prepared by the sol-gel method and used as a new type of magnetic photocatalyst in DBD system. It was found that the introduction of TiO₂/Fe₃O₄ in DBD system could effectively make use of the energy generated in DBD process and improve hydroxyl radical contributed by the main surface Fenton reaction, photocatalytic reaction and catalytic decomposition of dissolved ozone. Most part of MO (88%) was degraded during 30 min at peak voltage of 13 kV and TiO₂/Fe₃O₄ load of 100 mg/L, with a rate constant of 0.0731 min^?1 and a degradation yield of 7.23 g/(kW h). The coupled system showed higher degradation efficiency for MO removal.     

Effects of Calcination on the Physical and Photocatalytic Properties of TiO<Subscript>2</Subscript> Powders Prepared by Sol–Gel Template Method

TiO₂ powders were prepared by sol–gel template method and calcined under different conditions. XRD, BET and TEM were used to characterize the TiO₂ powders obtained. The photocatalytic activity of TiO₂ was investigated by the degradation of methyl orange. It was found that TiO₂ powder has the highest photocatalytic activity at a calcination temperature of 673 K. The effects of physical properties such as surface area, crystallinity and crystal phase on the photocatalytic activity of TiO₂ were discussed.     

Synthesis of Fe<Superscript>3+</Superscript> doped ordered mesoporous TiO<Subscript>2</Subscript> with enhanced visible light photocatalytic activity and highly crystallized anatase wall

Fe³⁺ doped mesoporous TiO₂ with ordered mesoporous structure were successfully prepared by the solvent evaporation-induced self-assembly process using P123 as soft template. The properties and structure of Fe³⁺ doped mesoporous TiO₂ were characterized by means of XRD, EPR, BET, TEM, and UV–vis absorption spectra. The characteristic results clearly show that the amount of Fe³⁺ dopant affects the mesoporous structure as well as the visible light absorption of the catalysts. The photocatalytic activity of the prepared mesoporous TiO₂ was evaluated from an analysis of the photodegradation of methyl orange under visible light irradiation. The results indicate that the sample of 0.50%Fe–MTiO₂ exhibits the highest visible light photocatalytic activity compared with other catalysts.     

Assessment of operating parameters for photocatalytic degradation of a textile dye by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/clinoptilolite nanocatalyst using Taguchi experimental design

In the current study, a nanophotocatalyst doped with of TiO₂ and Fe₂O₃ nanoparticles supported on Iranian clinoptilolite was synthesized and characterized by XRD, XRF, SEM, and EDX analyses. The results suggested the successful loading of TiO₂ and Fe₂O₃ nanoparticles onto the surface of clinoptilolite. The SEM images confirmed the average size of nanoparticles deposited on zeolite, which was about 20–40 nm. Furthermore, application of the synthesized photocatalyst in photocatalytic degradation of Acid Black 172 dye was studied using the Taguchi method and the chosen parameters were as follows: pH (2–7), dye concentration (50–200 mg/l), irradiation time (30–120 min), and catalyst dosage (0.5–1.5 g/l). The results indicate that dye concentration, pH, and irradiation time are respectively the most effective factors in these experiments while with the minimum dosage of the catalyst (0.5 g/l), up to 90 % removal efficiency could be achieved. The optimum value for each parameter was pH = 2, dye concentration = 50 mg/l, catalyst dosage = 1 g/l and irradiation time = 60 min, and the dye removal efficiency reached up to 100 % at these optimal conditions. Furthermore, after five-times recycling and reusing the catalyst, the efficiency of the photocatalytic degradation was reduced from 91.5 to 65.9 %, which is still an acceptable value.     

Photocatalytic degradation of organic compounds in aqueous systems by Fe and Ho codoped TiO<Subscript>2</Subscript>

Undoped, single-doped, and codoped TiO₂ nanoparticles were prepared by the sol-gel method and characterized with X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET)-specific surface area (S_BET), UV-Vis absorption spectra (UV-Vis), and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activity was evaluated by methyl orange (MO) degradation in an aqueous suspension under UV or simulated solar light illumination. XRD showed that all samples calcined at 600°C preserved the anatase structure, and doping inhibited the increase of crystallite size. The BET result revealed that doping improved the surface area of TiO₂. UV-Vis indicated that Fe³⁺-doping broadened the absorption profile of TiO₂. XPS demonstrated that doping was advantageous to absorb more surface hydroxyl groups or chemisorbed water molecules. Photocatalytic degradation showed that the photocatalytic activity of TiO₂ codoped with Fe³⁺ and Ho³⁺ ions was markedly improved. This was ascribed to the fact that there was a cooperative action in the two doped elements. Fe³⁺-doping broadens the absorption profile, improves photo utilization of TiO₂, and then generates more electronhole pairs. Ho³⁺-doping restrains the increase in grain size and retards the recombination of photo-generated electrons and holes.     

Preparation of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by mechanical alloying and annealing for sensitizing C-modified TiO<Subscript>2</Subscript> and acquirement of efficient photocatalyst

ZnFe₂O₄ nanoparticles sensitized by C-modified TiO₂ hybrids (ZnFe₂O₄–TiO₂/C) were successfully prepared by a feasible method. The ZnFe₂O₄ nanoparticles were prepared by mechanical alloying and annealing. The residual organic compounds in the synthetic process of TiO₂ were selected as the carbon source. The as-prepared composites were characterized by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, transmission electron microscopy, X-ray photoelectron spectroscopy, ultraviolet–visible light diffuse reflectance spectroscopy (UV–Vis) and N₂ adsorption–desorption analysis. The photocatalytic activity of the photocatalysts was measured by degradation of methyl orange under ultraviolet (UV) light and simulated solar irradiation, respectively. The results show that the carbon did not enter the TiO₂ lattice but adhered to the surface of TiO₂. The photocatalytic activity of the as-prepared C-modified TiO₂ (TiO₂/C) improved both under UV and simulated solar light irradiation, but the improvement was not dramatic. Introduction of ZnFe₂O₄ into the TiO₂/C could enhance the absorption spectrum range. The ZnFe₂O₄–TiO₂/C hybrids exhibited a higher photocatalytic activity both than that of the pure TiO₂ and TiO₂/C under either UV or simulated solar light irradiation. The complex synergistic effect plays an important role in improving the photocatalytic performance of ZnFe₂O₄–TiO₂/C composites. The optimum photocatalytic performance was obtained from the ZnFe₂O₄(0.8 wt%)–TiO₂/C sample.     

Preparation of nanocrystalline TiO<Subscript>2</Subscript> powders for photocatalytic oxidation of phenol

Nanocrystalline TiO₂ powders in the anatase, rutile, and mixed phases prepared by hydrolysis of TiCl₄ solution were of ultrafine size (<7.2 nm) with high specific surface areas in the range 167 to 388 m²/g. In the photocatalytic degradation of phenol as model reaction, the photocatalytic properties of TiO₂ nanoparticles were evaluated by use of UV–vis absorption spectroscopy and total organic carbon (TOC) content. The synthetic mixed-phase TiO₂ powder calcined at 400 °C had higher activity than pure anatase or rutile; it degraded more than 90% phenol to CO₂ (evaluated by TOC) after irradiation with near UV light for 90 min at a catalyst loading of 0.4 g/L. The TOC results indicated that rutile TiO₂ crystallites of particle size 7.2 nm resulted in much better photocatalytic performance than particles of larger size. This result suggested that some intermediates, not determined by UV–vis absorption spectroscopy, existed in the solution after the photocatalytic process over the rutile TiO₂ photocatalysts of larger crystallite size.