A study of the electrochemical behavior of an oxadiazole derivative electrodeposited on multi-wall carbon nanotube-modified electrode and its application as a hydrazine sensor

In this study, an oxadiazole multi-wall carbon nanotube-modified glassy carbon electrode (OMWCNT−GCE) was used as a highly sensitive electrochemical sensor for hydrazine determination. The surface charge transfer rate constant, k _s, and the charge transfer coefficient, α, for electron transfer between GCE and electrodeposited oxadiazole were calculated as 19.4 ± 0.5 s⁻¹ and 0.51, respectively at pH = 7.0. The obtained results indicate that hydrazine peak potential at OMWCNT−GCE shifted for 14, 109, and 136 mV to negative values as compared with oxadiazole-modified GCE, MWCNT−GCE, and activated GCE surface, respectively. The electron transfer coefficient, α, and the heterogeneous rate constant, k′, for the oxidation of hydrazine at OMWCNT−GCE were also determined by cyclic voltammetry measurements. Two linear dynamic ranges of 0.6 to 10.0 μM and 10.0 to 400.0 μM and detection limit of 0.17 μM for hydrazine determination were evaluated using differential pulse voltammetry. In addition, OMWCNT−GCE was shown to be successfully applied to determine hydrazine in various water samples.

     

Electrochemical behavior of electrodeposited rutin film on a multi-wall carbon nanotubes modified glassy carbon electrode. Improvement of the electrochemical reversibility and its application as a hydrazine sensor

By immobilizing rutin at the surface of a glassy carbon electrode (GCE) modified with multi-wall carbon nanotubes (MWCNT), a new modified electrode has been fabricated and its electrochemical behavior was investigated by cyclic voltammetry. Cyclic voltammograms of the resulting modified electrode show stable and a well defined redox couple with surface confined characteristics. The results show that the reversibility of rutin is significantly improved at a MWCNT modified GCE in comparison with GCE alone. The charge transfer coefficient, α, was calculated to be 0.4, and charge transfer rate constant, k_s, was 46.7 s⁻¹ in pH 8, indicating great facilitation of the electron transfer between rutin and MWCNT deposited on the electrode surface. The rutin MWCNT (RMWCNT) modified GCE showed excellent mediation of hydrazine oxidation: a decrease in the overvoltage of hydrazine electrooxidation was observed as well as a dramatic increase in the peak current compared to that seen at a rutin modified GCE (RMGCE), activated GCE or bare GCE. Hydrazine was determined amperometrically at the surface of RMWCNT modified GCE in pH 8. Under the optimized conditions the calibration curve is linear in the concentration range 2.0–190.0 μM hydrazine. The detection limit and sensitivity are 0.61 μM and 0.0656 μA μM⁻¹, respectively. Finally the kinetic parameters of the electron transfer coefficient, α, the heterogeneous rate constant of dependent to different potentials, k′(E), and the standard heterogeneous rate constant, k⁰, for oxidation of hydrazine at the RMWCNT surface were determined using various electrochemical methods. The advantages of this modified electrode for hydrazine determination are high sensitivity, excellent catalytic activity, short response time, wide linear range, and high exchange current density.     

Homogeneous electrocatalytic oxidation of captopril by iodide and its application to pharmaceutical analysis

Potassium iodide was used as a homogeneous electrocatalyst for the oxidation of captopril. Cyclic voltammetry and chronoamperometry were used in kinetic studies. The diffusion coefficient and catalytic rate constant were calculated to be 4.94?×?10^?5?cm²?s^?1 and 1.87?×?10³?M^?1?s^?1, respectively. Linear sweep voltammetry was applied to quantitative determination of captopril; a linear calibration curve was obtained in the range of 4.0?C500???M of captopril with a limit of detection of 0.84???M and a sensitivity of 0.035 A?M^?1. The method was applied to the determination of the drug in its tablets and validation methods showed that the results were quite satisfactory.     

Accelerating the electron transfer of choline oxidase using ionic-liquid/NH2-MWCNTs nano-composite

A nano-composite consisting of amine functionalized multi-walled carbon nanotubes and a room temperature ionic liquid (1-butyl-3-methylimidazolium tetrafluoroborate) was prepared and used for modification of glassy carbon electrode. By immobilizing choline oxidase (ChOx) on the modified electrode, the enzyme direct electron transfer has been achieved. The modified electrode exhibited a pair of well-defined cyclic voltammetric peaks at a formal potential of ?0.395?V versus Ag/AgCl in 0.2?M phosphate buffer solution at pH 7.0. This peak was characteristic of ChOx-FAD/FADH₂ redox couple. The electrochemical parameters such as charge transfer coefficient (??) and apparent heterogeneous electron transfer rate constant (k _s) were estimated to be 0.36 and 2.74?s^?1, respectively. When the enzyme electrode was examined for the detection of choline, a relatively high sensitivity (2.59???A?mM^?1) was obtained. Under the optimized experimental conditions, choline was detected in the concentration range from 6.9?×?10^?3 to 6.7?×?10^?1?mM with a detection limit of 2.7???M. The peak currents of ChOx were reasonably stable and retained 90% of its initial current after a period of 2?months.     

Direct electrochemical behavior of cytochrome c, and its determination on phytic acid modified electrode

Phytic acid (PA) with its unique structure was attached to a glassy carbon electrode (GCE) to form PA/GCE modified electrode which was characterized by electrochemical impedance. The electrochemical behavior of cytochrome c (Cyt c) on the PA/GCE modified electrode was explored by cyclic voltammetry and differential pulse voltammetry. The Cyt c displayed a quasi-reversible redox process on PA modified electrode pH 7.0 phosphate buffer solution with a formal potential (E ^0′) of 57 mV (versus Ag/AgCl). The peak currents were linearly related to the square root of the scan rate in the range of 20–120 mV·s^?1. The electron transfer rate constant was determined to be 12.5 s^?1. The PA/GCE modified electrode was applied to the determination of Cyt c, in the range of 5?×?10^?6 to 3?×?10^?4 M, the currents increase linearly to the Cyt c concentration with a correlation coefficient 0.9981. The detection limit was 1?×?10^?6 M (signal/noise?=?3).     

Poly(2-amino-5-(4-pyridinyl)-1, 3, 4-thiadiazole) film modified electrode for the simultaneous determinations of dopamine, uric acid and nitrite

Poly(2-amino-5-(4-pyridinyl)-1,3,4-thiadiazole) (PAPT) modified glassy carbon electrode (GCE) was fabricated and used for the simultaneous determinations of dopamine (DA), uric acid (UA) and nitrite (NO₂ ^?) in 0.1 mol?L^?1 phosphate buffer solution (PBS, pH 5.0) by using cyclic voltammetry and differential pulse voltammetry (DPV) techniques. The results showed that the PAPT modified GCE (PAPT/GCE) not only exhibited electrocatalytic activities towards the oxidation of DA, UA and NO₂ ^? but also could resolve the overlapped voltammetric signals of DA, UA and NO₂ ^? at bare GCE into three strong and well-defined oxidation peaks with enhanced current responses. The peak potential separations are 130 mV for DA–UA and 380 mV for UA–NO₂ ^? using DPV, which are large enough for the simultaneous determinations of DA, UA and NO₂ ^?. Under the optimal conditions, the anodic peak currents were correspondent linearly to the concentrations of DA, UA and NO₂ ^? in the ranges of 0.95–380 μmol?L^?1, 2.0–1,000 μmol?L^?1 and 2.0–1,200 μmol?L^?1 for DA, UA and NO₂ ^?, respectively. The correlation coefficients were 0.9989, 0.9970 and 0.9968, and the detection limits were 0.2, 0.35 and 0.6 μmol?L^?1 for DA, UA and NO₂ ^?, respectively. In 0.1 mol?L^?1 PBS pH 5.0, the PAPT film exhibited good electrochemical activity, showing a surface-controlled electrode process with the apparent heterogeneous electron transfer rate constant (k _s) of 25.9 s^?1 and the charge–transfer coefficient (α) of 0.49, and thus displayed the features of an electrocatalyst. Due to its high sensitivity, good selectivity and stability, the modified electrode had been successfully applied to the determination of analytes in serum and urine samples.     

Glassy carbon electrode modified with a film composed of Ni(II), quercetin and graphene for enzyme-less sensing of glucose

We present a modified glassy carbon electrode as a sensing platform for glucose. It is based on a composite film prepared from Ni(II) ion, quercetin and graphene. The sensor was characterized by cyclic voltammetry. The electron transfer coefficient, reaction rate constant and catalytic rate constant were determined and found to be 0.53, 5.4?s^?1 and 2.93?×?10³?M^?1 s^?1, respectively. The catalytic current depends linearly on the concentration of glucose in the range from 3 to 900???M, with a detection limit of 0.5???M (at an S/R of 3). The sensor exhibits good reproducibility, stability, fast response, and high sensitivity.

High-sensitive amperometric hydrazine sensor based on chemically synthesized zinc nitroprusside nanoparticle-supported carbon ceramic electrode

Zinc nitroprusside (ZnNP) nanoparticles were fabricated at the surface of zinc powder-doped carbon ceramic electrode (CCE) by a chemical derivatization process. This modified electrode was characterized by scanning electron microscopy, atomic force microscopy and cyclic voltammetry techniques. The charge transfer rate constant (k _s) and charge transfer coefficient (α) were calculated for the electron exchange reaction of the ZnNP thin film. The ZnNP nanoparticle-modified CCE (ZnNP|CCE) showed good electrocatalytic activity toward hydrazine oxidation. The limit of detection (S/N = 3) and sensitivity were found to be 0.16 µM and 0.21 µA/µM, respectively. The mechanism of hydrazine electrooxidation at the electrode surface was studied. Finally, the ZnNP|CCE was successfully used for the determination of trace amount of hydrazine in different spiked and real samples.     

Uranyl sensor based on a N,N′-bis(salicylidene)-2-hydroxy-phenylmethanediamine and multiwall carbon nanotube electrode

The electrochemical determination of uranyl was investigated by using carbon paste electrode modified with a Schiff base namely N,N??-bis(salicylidene)-2-hydroxy-phenylmethanediamine (SHPMD/CPE) and also in the presence of carbon nanotube (SHPMD/CNT/CPE). The both modified electrodes displayed an irreversible peak at E _pa?=?0.798?V versus Ag/AgCl. The electrocatalytic reduction of uranyl has been studied on SHPMD/CNT/CPE, using cyclic and differential pulse voltammetry, chronocoulometry and linear sweep techniques. Electrochemical parameters including the diffusion coefficient (D), the electron transfer coefficient (??), the ionic exchange current (i) and the redox reaction rate constant (K) were determined for the reduction of uranyl on the surface of the modified electrodes. Linear range concentration is 0.002?C0.6???mol?L^?1 and the detection limit of uranyl is 0.206?nmol?L^?1. The proposed method was used to detect uranyl in natural waters and good recovery was achieved.     

Nanostructured Base Electrochemical Sensor for Simultaneous Quantification and Voltammetric Studies of Levodopa and Carbidopa in Pharmaceutical Products and Biological Samples

A novel carbon paste electrode modified with carbon nanotubes and 5‐amino‐2′‐ethyl‐biphenyl‐2‐ol (5AEB) was fabricated. The electrochemical study of the modified electrode, as well as its efficiency for electrocatalytic oxidation of levodopa (LD) and carbidopa (CD), is described. Cyclic voltammetry (CV) was used to investigate the redox properties of this modified electrode at various scan rates. The apparent charge transfer rate constant, k_s, and transfer coefficient, a, for electron transfer between 5AEB and CPE were calculated as 17.3 s^?1 and 0.5, respectively. Square wave voltammetry (SWV) exhibits a linear dynamic range from 2.5×10^?7 to 2.0×10^?4 M and a detection limit of 9.0×10^?8 M for LD.     

Preparation and characterization of Ni(II)/polyacrylonitrile and carbon nanotube composite modified electrode and application for carbohydrates electrocatalytic oxidation

A nickel(II) into porous polyacrylonitrile–carbon nanotubes composite modified glassy carbon electrode (Ni/PAN-CNT/GCE) was fabricated by simple drop-casting and immersing technique. The unique electrochemical activity of Ni/PAN-CNT composite modified glassy carbon electrode was illustrated in 0.10?M NaOH using cyclic voltammetry. The Ni/PAN-CNT/GCE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple compared with Ni/PAN/GCE and Ni/CNT/GCE. The results of electrochemical impedance spectroscopy and scanning electron microscopy indicated the successful immobilization for PAN-CNT composite film. Kinetic parameters such as the electron transfer coefficient, α, and rate constant, k _s, of the electrode reaction were determined. Ni/PAN-CNT/GCE also shows good electrocatalytic activity toward the oxidation of carbohydrates (glucose, sucrose, fructose, and sorbitol). The electrocatalytic response showed a wide linear range (10–1,500, 12–3,200, 7–3,500, and 16–4,200?μM for glucose, sucrose, fructose, and sorbitol, respectively) as well as its experimental limit of detection can be achieved 6, 7, 5, and 11?μM for glucose, sucrose, fructose, and sorbitol, respectively. The modified electrode for carbohydrates determination is of the property of simple preparation, good stability, and high sensitivity.     

Amperometric sulfite sensor based on multiwalled carbon nanotubes/ferrocene-branched chitosan composites

A novel amperometric sensor for the determination of sulfite was fabricated based on multiwalled carbon nanotubes (MWCNTs)/ferrocene-branched chitosan (CHIT-Fc) composites-covered glassy carbon electrode (GCE). The electrochemical behavior of the sensor was investigated in detail by cyclic voltammetry. The apparent surface electron transfer rate constant (K_s) and charge transfer coefficient (α) of the CHIT-Fc/MWCNTs/GCE were also determined by cyclic voltammetry, which were about 1.93 cm s⁻¹ and 0.42, respectively. The sensor displayed good electrocatalytic activity towards the oxidation of sulfite. The peak potential for the oxidation of sulfite was lowered by at least 330 mV compared with that obtained at CHIT/MWCNTs/GCE. In optimal conditions, linear range spans the concentration of sulfite from 5 μM to 1.5 mM and the detection limit was 2.8 μM at a signal-to-noise ratio of 3. The proposed method was used for the determination of sulfite in boiler water. In addition, the sensor has good stability and reproducibility.     

Insights into electrocatalytic activity of epitaxial graphene on SiC from cyclic voltammetry and ac impedance spectroscopy

Electrocatalytic activity of graphene grown epitaxially on SiC is studied using cyclic voltammetry and electrochemical impedance spectroscopy. AFM images show step-like topography of SiC-graphene. For ferri-/ferrocyanide redox couple, no voltammetric response is observed at the pristine graphene. Basal planes of graphite are electrochemically inactive as well. After electrochemical oxidation, apparent redox peaks appear at both the graphene and graphite electrode. However, more intensive redox peaks are observed at graphene, where simultaneous redox reaction with the adsorbed and the diffused ferri-/ferrocyanide ions occurs. Electrochemical impedance measurements show that the graphene electrode behaves like an array of microelectrodes. We used the partially blocked electrode model to fit impedance data. Using the fitting parameters, a size of microelectrodes was found to be 23.8?±?2.1 μm and the active surface of graphene was estimated to be 21 %. A value of the standard electron transfer rate constant found for the anodized epitaxial graphene (2.16?±?0.32)?×?10^??3cm???s^??1) is by one order of magnitude lower than the standard rate constant estimated for the anodized graphite basal planes (～5?×?10^??2cm???s^??1). Electrochemical reduction causes total disappearance of electrochemical responses at the graphene electrode, whereas only slight decrease of the peak currents is observed at the reduced graphene. Such behavior proves that different activation mechanisms occur at the graphene and graphite electrodes.     

Electrochemistry and electrocatalytic activity of catechin film on a glassy carbon electrode toward the oxidation of hydrazine

A very stable electroactive film of catechin was electrochemically deposited on the surface of activated glassy carbon electrode. The electrochemical behavior of catechin modified glassy carbon electrode (CMGCE) was extensively studied using cyclic voltammetry. The properties of the electrodeposited films, during preparation under different conditions, and the stability of the deposited film were examined. The charge transfer coefficient (α) and charge transfer rate constant (k _s) for catechin deposited film were calculated. It was found that the modified electrode exhibited excellent electrocatalytic activity toward hydrazine oxidation and it also showed a very large decrease in the overpotential for the oxidation of hydrazine. The CMGCE was employed to study electrocatalytic oxidation of hydrazine using cyclic voltammetry, rotating disk voltammetry, chronoamperometry, amperometry and square-wave voltammetry as diagnostic techniques. The catalytic rate constant of the modified electrode for the oxidation of hydrazine was determined by cyclic voltammetry, chronoamperometry and rotating disk voltammetry and was found to be around 10⁻³ cm s⁻¹ . In the used different voltammetric methods, the plot of the electrocatalytic current versus hydrazine concentration is constituted of two linear segments with different ranges of hydrazine concentration. Furthermore, amperometry in stirred solution exhibits a detection limit of 0.165 μM and the precision of 4.7% for replicate measurements of 40.0 μM solution of hydrazine.     

Adsorptive Stripping Differential Pulse Voltammetric Determination of Risperidone with a Multi‐Walled Carbon Nanotube‐Ionic Liquid Paste Modified Glassy Carbon Electrode

A new composite electrode has been fabricated based on coating multi‐walled carbon nanotubes (MWCNTs) and n‐octylpyridinum hexafluorophosphate (OPPF₆) ionic liquid composite on a glassy carbon (GC) electrode (OPPF₆‐MWCNTs/GCE). This electrode shows very attractive electrochemical performances for electrooxidation of risperidone (RIS) compared to conventional electrodes using carbon and mineral oil, notably improved sensitivity and stability. The oxidation peak potentials in cyclic voltammogram of RIS on the OPPF₆‐MWCNTs/GCE was occurred around 230 mV vs. SCE at Britton–Robinson (B–R) buffer (pH 4.0) at scan rate of 100 mV s^?1. The electrochemical parameters such as diffusion coefficient (D), charge transfer coefficient (α) and the electron transfer rate constant (k/_s) were determined using cyclic voltammetry. Under the optimized conditions, the peak current was linear to risperidone concentration over the concentration range of 10–200 nM with sensitivity of 0.016 μA/nM^?1 using differential pulse voltammetry. The detection limit was 6.54 nM (S/N = 3). The electrode also displayed good selectivity and repeatability. In the presence of clozapine (CLZ) the response of RIS kept almost unchanged. Thus this electrode could find application in the determination of RIS in some real samples. The analytical performance of the OPPF₆‐MWCNTs/GCE was demonstrated for the determination of RIS in human serum and pharmaceutical samples.     

Behavior of Palladium Nanoparticles in the Absence or Presence of Cobalt Tetraaminophthalocyanine for the Electrooxidation of Hydrazine

We report on the electrodeposition of palladium nanoparticles (PdNPs) on a glassy carbon electrode (GCE) and onto a poly‐CoTAPc‐GCE (CoTAPc=cobalt tetraamino phthalocyanine) surface. The electrodes are denoted as PdNPs‐GCE and PdNPs/poly‐CoTAPc‐GCE, respectively. PdNPs/poly‐CoTAPc‐GCE showed the best activity for the oxidation of hydrazine at the lowest potential of ?0.28 V and with the highest currents. The results were further supported by electrochemical impedance spectroscopy (EIS) which showed that there was less resistance to charge transfer for PdNPs/poly‐CoTAPc‐GCE compared to PdNPs‐GCE. The catalytic rate constant for hydrazine oxidation was 6.12×10⁸ cm³ mol^?1 s^?1 using PdNPs/poly‐CoTAPc‐GCE.     

Acetylferrocene Modified Carbon Paste Electrode; A Sensor for Electrocatalytic Determination of Hydrazine

The electrocatalytic oxidation of hydrazine at a carbon paste electrode spiked with acetylferrocene as a mediator was studied by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. In contrast to other ferrocenic compounds, acetylferrocene exhibits a chemical irreversible behavior, but it can act as an effective mediator for electrocatalytic oxidation of hydrazine, too. The heterogeneous electron transfer rate constant between acetylferrocene and the electrode substrate (carbon paste) and the diffusion coefficient of spiked acetylferrocene in silicon oil were estimated to be about 3.45×10^?4 cm s^?1 and 4.45×10^?9 cm² s^?1, respectively. It has been found that under the optimum conditions (pH 7.5) the oxidation of hydrazine occurs at a potential of about 228 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak current of hydrazine was linearly dependent on its concentration and the obtained linear range was 3.09×10^?5 M–1.03×10^?3 M. The detection limit (2σ) has been determined as 2.7×10^?5 M by cyclic voltammetry. Also, the peak current was increased linearly with the concentration of hydrazine in the range of 1×10^?5 M–1×10^?3 M by differential pulse voltammetry with a detection limit of 1×10^?5 M. This catalytic oxidation of hydrazine has been applied as a selective, simple, and precise new method for the determination of hydrazine in water samples.     

Application of a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole/carbon nanotube modified glassy carbon electrode for voltammetric determination of hydrazine in water samples

The electrochemical behaviour of hydrazine at a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole‐triazole/carbon nanotube modified glassy carbon electrode has been studied. The modified electrode shows an excellent electrocatalytic activity for the oxidation of hydrazine and accelerates electron transfer rate. The electrocatalytic current increases linearly with hydrazine concentration in the range 0.5–700.0 μm and the detection limit for hydrazine was 33.0 ± 2.0 nm . The diffusion coefficient (D = 2.5 ± 0.1 × 10^?5 cm² s^?1) and kinetic parameters such as the electron transfer coefficient, (α = 0.52) and the heterogeneous rate constant (k′ = 5.5 ± 0.1 × 10^?3 cm s^?1) for hydrazine were determined using electrochemical approaches. Finally, the method was employed for the determination of hydrazine in water samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Enhanced electron transfer by bovine serum albumin covalently attached to glassy carbon electrode and its application to determination of hydroquinone

Bovine serum albumin (BSA) was covalently attached to glassy carbon electrode (GCE) surface by the electrochemical method. An enhancement for the redox of hydroquinone (HQ) on BSA/GCE was confirmed by cyclic voltammetry and electrochemical impedance spectroscopy measurement. The electron transfer rate constant (k _s) on the BSA/GCE electrode is almost three orders of magnitude higher than that on bare GCE. The enhancing effect can be attributed to the electrostatic force between the positively charged HQ and negatively charged BSA. It is found that the enhanced redox process of HQ can be used to determine HQ sensitively. The oxidation current can reach 95% of its steady-state value within 30 s. The linear range for HQ determination is from 2.5 × 10^?8 M to 1.325 × 10^?6 M with a detection limit of 8.6 × 10^?9 M at a signal-to-noise ratio of 3. The study may provide a simple, rapid and sensitive method for determination of HQ which is present in the natural environment and in chemical industry effluent.     

Polymer films on electrodes: Part XVIII. Determination of heterogeneous electron transfer kinetics at poly(vinylferrocene) and nafion/Ru(bpy)2+3 polymer-modified electrodes by convolution voltammetry

Convolution voltammetry was used to evaluate the rates of heterogeneous charge transfer to ferrocene groups in poly(vinylferrocene) and to Ru(bpy)²⁺₃ in Nafion-modified electrodes under semi-infinite conditions. This technique allows correction for uncompensated resistance and double layer capacitance, as well as detrmination of the diffusion coefficient, D, transfer coefficient, α, and half-wave potential, E_1/2, from a single cyclic voltammogram. Vinylferrocene in solution and a bound copolymer of vinylferrocene and styrene in a ratio of 58:42 were also examined. For the polymer films, the heterogeneous charge transfer rate constants, k°, are 10^?4 ≥ k° ≥ 10^?5 cm/s; these values are about two order of magnitude smaller than those for the similar species in homogeneous solution. The values of k°/D^1/2, however, are comparable to those in soluton; 10 > (k°/D^1/2) > 0.1 s^?1/2.