Direct observation of the kinetically relevant site of CO hydrogenation on supported Ru catalyst at 700 K by time-resolved FT-IR spectroscopy

Time-resolved FT-IR spectra of carbon monoxide hydrogenation over alumina-supported ruthenium particles were recorded on the millisecond time scale at 700 K using pulsed release of CO and a continuous flow of H(2)-N(2) (ratio 0.067 or 0.15, 1 atm total pressure). Adsorbed carbon monoxide was detected along with gas phase products methane (3016 and 1306 cm(-1)), water (1900-1300 cm(-1)), and carbon dioxide (2348 cm(-1)). Aside from adsorbed CO, no other surface species were observed. The rate of formation of methane is 2.5 +/- 0.4 s(-1) and coincides with the rate of carbon dioxide growth (3.4 +/- 0.6 s(-1)), thus indicating that CH(4) and CO(2) originate from a common intermediate. The broad band of adsorbed carbon monoxide has a maximum at 2010 cm(-1) at early times (36 ms) that shifts gradually to 1960 cm(-1) over a period of 3 s as a result of the decreasing surface concentration of CO. Kinetic analysis of the adsorbed carbon monoxide reveals that surface sites absorbing at the high frequency end of the infrared band are temporally linked to gas phase product growth. Specifically, a (linear) CO site at 2026 cm(-1) decays with a rate constant of 2.9 +/- 0.1 s(-1), which coincides with the rise constant of CH(4). This demonstrates that the linear CO site at 2026 cm(-1) is the kinetically most relevant one for the rate-determining CO dissociation step under reaction conditions at 700 K.     

Direct measurement of Criegee intermediate (CH2OO) reactions with acetone, acetaldehyde, and hexafluoroacetone

Criegee biradicals, i.e., carbonyl oxides, are critical intermediates in ozonolysis and have been implicated in autoignition chemistry and other hydrocarbon oxidation systems, but until recently the direct measurement of their gas-phase kinetics has not been feasible. Indirect determinations of Criegee intermediate kinetics often rely on the introduction of a scavenger molecule into an ozonolysis system and analysis of the effects of the scavenger on yields of products associated with Criegee intermediate reactions. Carbonyl species, in particular hexafluoroacetone (CF(3)COCF(3)), have often been used as scavengers. In this work, the reactions of the simplest Criegee intermediate, CH(2)OO (formaldehyde oxide), with three carbonyl species have been measured by laser photolysis/tunable synchrotron photoionization mass spectrometry. Diiodomethane photolysis produces CH(2)I radicals, which react with O(2) to yield CH(2)OO + I. The formaldehyde oxide is reacted with a large excess of a carbonyl reactant and both the disappearance of CH(2)OO and the formation of reaction products are monitored. The rate coefficient for CH(2)OO + hexafluoroacetone is k(1) = (3.0 ± 0.3) × 10(-11) cm(3) molecule(-1) s(-1), supporting the use of hexafluoroacetone as a Criegee-intermediate scavenger. The reactions with acetaldehyde, k(2) = (9.5 ± 0.7) × 10(-13) cm(3) molecule(-1) s(-1), and with acetone, k(3) = (2.3 ± 0.3) × 10(-13) cm(3) molecule(-1) s(-1), are substantially slower. Secondary ozonides and products of ozonide isomerization are observed from the reactions of CH(2)OO with acetone and hexafluoroacetone. Their photoionization spectra are interpreted with the aid of quantum-chemical and Franck-Condon-factor calculations. No secondary ozonide was observable in the reaction of CH(2)OO with acetaldehyde, but acetic acid was identified as a product under the conditions used (4 Torr and 293 K).     

Surface products and coverage dependence of dissociative ethane adsorption on Pt{110}-(1 x 2)

The dissociation of ethane on Pt{110}-(1 x 2) has been studied using supersonic molecular beam and temperature-programmed reaction techniques. The study unequivocally shows that the stable dissociation product of ethane on Pt{110}-(1 x 2) at all coverages is CCH2 at 350-400 K and CCH at 440 K. Temperature-programmed-reaction (TPR) experiments indicate that the CCH2 species decomposes to CCH with a reaction-limited peak temperature of 430 K. Above 450 K, the CCH species becomes unstable and decomposes with a peak temperature of 540 K. By 600 K, ethane dehydrogenates completely to form a surface carbon layer. The sticking probability is initially 0.02 at 370 K and 0.03 at 600 K and follows a linear (1-2theta) dependence for coverages of up to theta = 0.4 ML, where theta is defined as the number of C2Hx units per (1 x 2) unit cell. However, a much weaker coverage dependence at 800 K suggests that the carbon agglomerates into high-density islands.     

SiO2—Al2O3和MgO催化剂上吸附CH3NO2的TPD和IR研究

用TPD和IR方法研究了CH_3NO_2在典型固体酸SiO_2-Al_2O_3和固体碱MgO催化剂上的吸附分解。结果表明,在SiO_2-Al_2O_3表面CH_3NO_2吸附转化为表面甲酰胺物种,后者在高温下分解为CO_2和NH_3。在MgO表面CH_3NO_2吸附形成多种表面化学物种,它们在升温过程中脱附,并通过表面亚硝基甲烷物种分解为NO、C_2H_4、C_2H_6和N_2O.讨论了CH_3NO_2分解过程中表面酸、碱中心的作用。     

Spectroscopic Identification of Adsorbed Intermediates Derived from the CO+H(2)O Reaction on Zeolite-Encapsulated Gold Catalysts

Identification of reaction intermediates in the water-gas shift reaction (WGSR: H(2)O+CO-->H(2)+CO(2)) on Au(n+) (1相似文献   

碘乙醇在Ni(100)表面的吸附和热分解-碳氢化合物氧化的中间产物：羟乙基和氧金属环

利用热脱附(TPD)实验和X射线光电子能谱(XPS)研究了碘乙醇在Ni(100)表面的吸附和热反应过程. 实验结果表明碘乙醇在100 K时以两种分子的形式吸附在Ni(100)的表面, 即: 以碘原子端吸附在表面或以碘原子端和羟基端同时吸附在表面. 由于两种吸附形式的分子的一致分解和吸附分子的不均匀性, 在140 K引起了较复杂的化学反应, 伴有少量的乙烯和水产生. 碘乙醇在150 K经过C—I键断裂, 有80%碘乙醇生成—O(H)CH2CH2—中间产物, 20%的碘乙醇生成羟乙基中间产物. 羟乙基在160 K的转化过程中包括两个互相竞争的化学反应: 与表面的氢原子进行还原反应生成乙醇, 或失去一个β-H原子生成表面乙烯醇. 另外, 在相同的温度下—O(H)CH2CH2—中间产物经过脱氢反应产生—OCH2CH2—氧金属环. 羟乙基和氧金属环都会发生异构, 分别在210 K和250 K生成乙醛, 这些乙醛一部分从表面脱出, 其余的部分发生分解反应产生氢气、水和一氧化碳. 在实验基础上, 进一步探讨了这种化学过程在催化中的作用和指导意义.     

Experimental and DFT studies of the conversion of ethanol and acetic acid on PtSn-based catalysts

Reaction kinetics studies were conducted for the conversions of ethanol and acetic acid over silica-supported Pt and Pt/Sn catalysts at temperatures from 500 to 600 K. Addition of Sn to Pt catalysts inhibits the decomposition of ethanol to CO, CH4, and C2H6, such that PtSn-based catalysts are active for dehydrogenation of ethanol to acetaldehyde. Furthermore, PtSn-based catalysts are selective for the conversion of acetic acid to ethanol, acetaldehyde, and ethyl acetate, whereas Pt catalysts lead mainly to decomposition products such as CH4 and CO. These results are interpreted using density functional theory (DFT) calculations for various adsorbed species and transition states on Pt(111) and Pt3Sn(111) surfaces. The Pt3Sn alloy slab was selected for DFT studies because results from in situ (119)Sn M?ssbauer spectroscopy and CO adsorption microcalorimetry of silica-supported Pt/Sn catalysts indicate that Pt-Sn alloy is the major phase present. Accordingly, results from DFT calculations show that transition-state energies for C-O and C-C bond cleavage in ethanol-derived species increase by 25-60 kJ/mol on Pt3Sn(111) compared to Pt(111), whereas energies of transition states for dehydrogenation reactions increase by only 5-10 kJ/mol. Results from DFT calculations show that transition-state energies for CH3CO-OH bond cleavage increase by only 12 kJ/mol on Pt3Sn(111) compared to Pt(111). The suppression of C-C bond cleavage in ethanol and acetic acid upon addition of Sn to Pt is also confirmed by microcalorimetric and infrared spectroscopic measurements at 300 K of the interactions of ethanol and acetic acid with Pt and PtSn on a silica support that had been silylated to remove silanol groups.     

Theory of C2Hx species on Pt{110} (1x2): reaction pathways for dehydrogenation

A complete reaction sequence for molecular dissociation at a surface has been characterized using density functional theory. The barriers for sequential ethane dehydrogenation on Pt{110} are found to fall into distinct energy sets: very low barriers, with values in the range of 0.29-0.42 eV, for the initial ethane dissociation to ethene and ethylidene at the surface; medium barriers, in the range of 0.72-1.10 eV, for dehydrogenation of C(2)H(4) fragments to vinylidene and ethyne; and high barriers, requiring more than 1.45 eV, for further dehydrogenation. For dissociation processes where more than one pathway has been found, the lowest energetic route links the most stable reactant adsorbed state at the surface to a product state involving the hydrocarbon moiety adsorbed in its most stable configuration at the surface. Hence there is a clear link between surface stability and kinetics for these species.     

Kinetics of the reactions of CH2I, CH2Br, and CHBrCl radicals with NO2 in the temperature range 220-360 K

The kinetics of the CH2I + NO2, CH2Br + NO2, and CHBrCl + NO2 reactions have been studied at temperatures between 220 and 360 K using laser photolysis/photoionization mass spectrometry. Decays of radical concentrations have been monitored in time-resolved measurements to obtain reaction rate coefficients under pseudo-first-order conditions. The bimolecular rate coefficients of all three reactions are independent of the bath gas (He or N2) and pressure within the experimental range (2-6 Torr) and are found to depend on temperature as follows: k(CH2I + NO2) = (2.18 +/- 0.07) x 10(-11) (T / 300 K)(-1.45) (+/- 0.22) cm3 molecule(-1) s(-1) (220-363 K), k(CH2Br + NO2) = (1.76 +/- 0.03) x 10(-11) (T/300 K)(-0.86) (+/- 0.09) cm3 molecule(-1) s(-1) (221-363 K), and k(CHBrCl + NO2) = (8.81 +/- 0.28) x 10(-12) (T/300 K)(-1.55) (+/- 0.34) cm3 molecule(-1) s(-1) (267-363 K), with the uncertainties given as one-standard deviations. Estimated overall uncertainties in the measured bimolecular reaction rate coefficients are about +/-25%. In the CH2I + NO2 and CH2Br + NO2 reactions, the observed product is formaldehyde. For the CHBrCl + NO2 reaction, the product observed is CHClO. In addition, I atom and iodonitromethane (CH2INO2) or iodomethyl nitrite (CH2IONO) formations have been detected for the CH2I + NO2 reaction.     

乙烷/H2O/O2/N2体系中光致过氧化物的产生

采用长光路Fourier红外光谱(LP-FTIR)和高压液相色谱(HPLC)技术研究了乙烷/H2O/O2/N2光化学体系中过氧化物的产生，证实乙烷降解产物中有过氧化氢、乙基过氧化氢(CH3CH2OOH,EHP)和过氧乙酸[CH3C(O)OOH,PAA]，并首次发现了甲基过氧化氢(CH3OOH,MHP)、羟甲基过氧化氢(HOCH2OOH,HMHP)和过氧甲醚(CH3OOCH3,DMP).H2O2,MHP和EHP的最大计算产率分别为6.8%，6.4%和6.7%，是乙烷降解生成的主要过氧化产物。MHP主要来自乙烷降解过程中的中间物乙醛的光解。HMHP的检出表明乙烷降解过程中可能有Criegee中间体.CH2OO.产生。OH自由基引发的乙烷降解反应可能是对流层大气H2O2，MHP及EHP的重要来源之一。     

Mechanistic and spectroscopic identification of initial reaction intermediates for prenal decomposition on a platinum model catalyst

The prediction of a reaction mechanism and the identification of the corresponding chemical intermediates is a major challenge in surface science and heterogeneous catalysis, due to a complex network of elementary steps and surface species. Here we demonstrate how to overcome this difficulty by tracking the temperature dependent formation of the initial reaction intermediates and identifying the decomposition pathways in the case of prenal, an α,β-unsaturated aldehyde, on the Pt(111) model catalyst surface by combining vibrational spectroscopy, thermal reaction/desorption spectroscopy (TPRS) experiments and detailed theoretical analysis. TPRS characterization of this reaction up to 600 K shows a series of desorption states of H(2) (～280 K, 410 K and 473 K) and CO (～414 K), giving valuable insights into the sequence of elementary steps suggesting that the loss of hydrogen and the carbonyl functions are among the first elementary steps. HREELS experiments recorded after annealing to specific temperatures result in complex spectra, which can be assigned to several subsequently formed and transformed surface intermediates. Starting from stable prenal adsorption structures, complementary DFT calculations allow the determination of the most likely reaction pathway for the initial decomposition steps and the identification of the corresponding intermediates by comparison with HREELS. The decomposition occurs from the strongly bonded prenal adsorption structures via a dehydro-η(3)-triσ(CCC)-H1 intermediate to the highly stable η(1)-isobutylidyne species at high temperatures.     

Mechanistic information on the reductive elimination from cationic trimethylplatinum(IV) complexes to form carbon-carbon bonds

Cationic complexes of the type fac-[(L(2))Pt(IV)Me(3)(pyr-X)][OTf] (pyr-X = 4-substituted pyridines; L(2) = diphosphine, viz., dppe = bis(diphenylphosphino)ethane and dppbz = o-bis(diphenylphosphino)benzene; OTf = trifluoromethanesulfonate) undergo C-C reductive elimination reactions to form [L(2)Pt(II)Me(pyr-X)][OTf] and ethane. Detailed studies indicate that these reactions proceed by a two-step pathway, viz., initial reversible dissociation of the pyridine ligand from the cationic complex to generate a five-coordinate Pt(IV) intermediate, followed by irreversible concerted C-C bond formation. The reaction is inhibited by pyridine. The highly positive values for DeltaS()(obs) = +180 +/- 30 J K(-1) mol(-1), DeltaH(obs) = 160 +/- 10 kJ mol(-1), and DeltaV()(obs) = +16 +/- 1 cm(3) mol(-1) can be accounted for in terms of significant bond cleavage and/or partial reduction from Pt(IV) to Pt(II) in going from the ground to the transition state. These cationic complexes have provided the first opportunity to carry out detailed studies of C-C reductive elimination from cationic Pt(IV) complexes in a variety of solvents. The absence of a significant solvent effect for this reaction provides strong evidence that the C-C reductive coupling occurs from an unsaturated five-coordinate Pt(IV) intermediate rather than from a six-coordinate Pt(IV) solvento species.     

Low temperature kinetics, crossed beam dynamics and theoretical studies of the reaction S((1)D) + CH4 and low temperature kinetics of S((1)D) + C2H2

The reaction between sulfur atoms in the first electronically excited state, S((1)D), and methane (CH(4)), has been investigated in a complementary fashion in (a) crossed-beam dynamics experiments with mass spectrometric detection and time-of-flight (TOF) analysis at two collision energies (30.4 and 33.6 kJ mol(-1)), (b) low temperature kinetics experiments ranging from 298 K down to 23 K, and (c) electronic structure calculations of stationary points and product energetics on the CH(4)S singlet potential energy surface. The rate coefficients for total loss of S((1)D) are found to be very large (ca. 2 × 10(-10) cm(3) molec(-1) s(-1)) down to very low temperatures indicating that the overall reaction is barrier-less. Similar measurements are also performed for S((1)D) + C(2)H(2), and also for this system the rate coefficients are found to be very large (ca. 3 × 10(-10) cm(3) molec(-1) s(-1)) down to very low temperatures. From laboratory angular and TOF distributions at different product masses for the reaction S((1)D) + CH(4), it is found that the only open reaction channel at the investigated collision energies is that leading to SH + CH(3). The product angular, T(θ), and translational energy, P(E'(T)), distributions in the center-of-mass frame are derived. The reaction dynamics are discussed in terms of two different micromechanisms: a dominant long-lived complex mechanism at small and intermediate impact parameters with a strongly polarized T(θ), and a direct pickup-type (stripping) mechanism occurring at large impact parameters with a strongly forward peaked T(θ). Interpretation of the experimental results on the S((1)D) + CH(4) reaction kinetics and dynamics is assisted by high-level theoretical calculations on the CH(4)S singlet potential energy surface. The dynamics of the SH + CH(3) forming channel are compared with those of the corresponding channel (leading to OH + CH(3)) in the related O((1)D) + CH(4) reaction, previously investigated in crossed-beams in other laboratories at comparable collision energies. The possible astrophysical relevance of S((1)D) reactions with hydrocarbons, especially in the chemistry of cometary comae, is discussed.     

Ni／Al2O3催化剂上CH4／CO2重整的脉冲反应研究

报道了用脉冲反应研究Ｎｉ／Ａｌ２Ｏ３催化剂上ＣＨ４／ＣＯ２重整反应的结果。脉冲反应显示，在还原的Ｎｉ／Ａｌ２Ｏ３催化剂上，ＣＨ４在６７３Ｋ就开始发生分解，并有Ｃ２Ｈ６、Ｃ２Ｈ４生成，１０２３Ｋ下，ＣＨ４几乎完全分解，单纯的ＣＯ２则很难在还原的催化剂上发生反应，在９７３Ｋ以上的高温下才会有少量Ｃ胜成ＣＯ．ＣＨＣＯ２的脉冲反应表明，当ＣＨ４在较低温度下开始分解时，ＣＯ２也会发生分解，并生成ＣＯ。脉冲反     

Reaction dynamics of Ca(4s3d 1D2)+CH4-->CaH(X 2Sigma+)+CH3: reaction pathway and energy disposal for the CaH product

The reaction pathway for Ca(4s3d 1D2)+CH4-->CaH(X 2Sigma+)+CH3 has been investigated by using a pump-probe technique in combination with potential-energy surface (PES) calculations. The nascent product distributions of CaH have been characterized with Boltzmann rotational temperatures of 1013+/-102 and 834+/-70 K for the v=0 and 1 levels, respectively, and a Boltzmann vibrational temperature of 1313+/-173 K. The rotational and vibrational energy partitions in CaH have been estimated to be 461+/-45 and 252+/-15 cm(-1), respectively. According to the PES calculations, the pathway favors an insertion mechanism. Ca(3 1D2) approaches CH4 along an attractive potential surface in a C2v (or Cs) symmetry and then the collision complex undergoes nonadiabatic transition to the reactive ground-state surface. An Arrhenius plot shows a potential-energy requirement of 2695+/-149 cm(-1), which accounts for the endothermicity of 2930 cm(-1) for the reaction scheme. The Ca-C bond distance in the transition state structure is short enough to allow for tight orbital overlap between CaH and CH3. The strong coupling between the moieties renders the energy transfer sufficient from CaH into the CH3 radical. As compared to the Ca(4 1P1) reaction, the dissociation lifetime of the intermediate complex with less excess energy is prolonged so as to cause much less vibrational energy disposal into CaH.     

ZrO2催化剂上吸附CH3NO2的分解

用TPD和IR谱研究了CH_3NO_2在ZrO_2催化剂上的吸附活化和分解反应。结果表明,室温下CH_3NO_2在ZrO_2表面发生不可逆化学吸附,它们在TPD过程中可完全分解生成HCN、CO_2、CO、NH_3、H_2O和微量NO。其中H_2O和NO的脱附峰出现在383K附近。其它产物在543K附近出现极大值。IR结果表明,CH_3NO_2在ZrO_2上吸附形成诸如[CH_2NO_2],和/或吸附物种。这些吸附物种在升高温度时转化为表面态“HCN”。“HCN”或脱附,或进一步向表面“HCONH_2”和/或“HCOO~-”转化,后两种表面物种分解可产生CO_2、NH_3和CO。将这些结果与CH_3NO_2在SiO_2-Al_O_3和MgO催化剂上的结果进行了比较,讨论了酸-碱双功能性ZrO_2催化剂上CH_3NO_2活化分解的特点。     

Ni(OCH3)2/SiO2催化剂的制备及其合成碳酸二甲酯的反应性能

采用表面改性和离子交换相结合的方法，制备了负载型单核金属甲氧基配合物Ni(OCH3)2/SiO2催化剂。利用IR、TPD、TPSR和微反技术，考察了催化剂的表面结构以及CO2、CH3OH在催化剂表面上的化学吸附和反应性能。结果表明，负载型单核金属甲氧基配合物Ni(OCH3)2/SiO2中，Ni^2 与载体SiO2表面的O^2-以双齿形式配位；在催化剂表面存在CO2的桥式吸附态和甲氧碳酸酯基物种两种吸附态，CH3OH则只有一种分子吸附态。在373-473K条件下，CO2和CH3OH在催化剂上的反应物主要是DMC、H2O以及少量的CO、CH4和CH2O，催化剂的活性由表面甲氧碳酸酯基物种与分子吸附态甲醇的反应决定的。讨论了催化剂上CO2和CH3OH的活化过程及吸附态的形成机理。     

Coupling vs surface-etching reactions of alkyl halides on GaAs(100). 2. CH2I2 reactions

Surface reactions of CH2I2 on gallium-rich GaAs(100)-(4 x 1), studied by temperature programmed desorption and X-ray photoelectron spectroscopy (XPS), show CH2I2 adsorbs dissociatively at liquid nitrogen temperatures to form surface chemisorbed CH2(ads) and I(ads) species. Controlled hydrogenation of a fraction of the CH2(ads) species in the chemisorbed layer by the background hydrogen radicals results in a surface layer comprising both CH3(ads) and CH2(ads) species. This hydrogenation step initiates a plethora of further surface reactions involving these two species and I(ads). Thermal activation leads to three sequential methylene insertions (CH2(ads)) into the CH3-surface bond to form three higher alkyl (ethyl (C2), propyl (C3), and butyl (C4)) species, which undergo beta-hydride elimination to evolve the respective higher alkene (ethene, propene, and butene). In competition with beta-hydride elimination, reductive elimination of the ethyl and propyl species with I(ads) occurs to liberate the respective alkyl iodide. Beta-hydride elimination in the alkyls, in the temperature range 420-520 K, is the more dominant pathway, and it is also the rate-limiting step for further chain propagation. The evolution of the alkyl iodides represents the only pathway for the removal of surface iodines in this study and is different from previous investigations where gallium and arsenic iodide etch products (GaI(x), AsI(x) (x = 1-3)) formed instead. The desorption of methane and methyl iodide, formed from surface CH3(ads) species at high temperatures by the reaction between surface methylenes and hydrogens eliminated from the surface C2-C4 alkyls, terminates the chain propagation. We discuss the reaction mechanisms by which the observed reaction products form and postulate reasons for the reaction pathways adopted by the surface species.     

Surface chemistry of CN bond formation from carbon and nitrogen atoms on Pt(111)

The mechanism of CN bond formation from CH3 and NH3 fragments adsorbed on Pt(111) was investigated with reflection absorption infrared spectroscopy (RAIRS), temperature-programmed desorption (TPD), and X-ray photoelectron spectroscopy (XPS). The surface chemistry of carbon-nitrogen coupling is of fundamental importance to catalytic processes such as the industrial-scale synthesis of HCN from CH4 and NH3 over Pt. Since neither CH4 nor NH3 thermally dissociate on Pt(111) under ultrahigh vacuum (UHV) conditions, the relevant surface intermediates were generated through the thermal decomposition of CH3I and the electron-induced dissociation of NH3. The presence of surface CN is detected with TPD through HCN desorption as well as with RAIRS through the appearance of the vibrational features characteristic of the aminocarbyne (CNH2) species, which is formed upon hydrogenation of surface CN at 300 K. The RAIRS results show that HCN desorption at approximately 500 K is kinetically limited by the formation of the CN bond at this temperature. High coverages of Cads suppress CN formation, but the results are not influenced by the coadsorbed I atoms. Cyanide formation is also observed from the reaction of adsorbed N atoms and carbon produced from the dissociation of ethylene.     

Infrared spectroscopic study of the carbon dioxide adsorption on the surface of Ga2O3 polymorphs

The adsorption of CO(2) over a set of gallium (III) oxide polymorphs with different crystallographic phases (alpha, beta, and gamma) and surface areas (12-105 m(2) g(-1)) was studied by in situ infrared spectroscopy. On the bare surface of the activated gallias (i.e., partially dehydroxylated under O(2) and D(2) (H(2)) at 723 K), several IR signals of the O-D (O-H) stretching mode were assigned to mono-, di- and tricoordinated OD (OH) groups bonded to gallium cations in tetrahedral and/or octahedral positions. After exposing the surface of the polymorphs to CO(2) at 323 K, a variety of (bi)carbonate species emerged. The more basic hydroxyl groups were able to react with CO(2), to yield two types of bicarbonate species: mono- (m-) and bidentate (b-) [nu(as)(CO(3)) = 1630 cm(-1); nu(s)(CO(3)) = 1431 or 1455 cm(-1) (for m- or b-); delta(OH) = 1225 cm(-1)]. Together with the bicarbonate groups, IR bands assigned to carboxylate [nu(as)(CO(2)) = 1750 cm(-1); nu(s)(CO(2)) = 1170 cm(-1)], bridge carbonate [nu(as)(CO(3)) = 1680 cm(-1); nu(s)(CO(3)) = 1280 cm(-1)], bidentate carbonate [nu(as)(CO(3)) = 1587 cm(-1); nu(s)(CO(3)) = 1325 cm(-1)], and polydentate carbonate [nu(as)(CO(3)) = 1460 cm(-1); nu(s)(CO(3)) = 1406 cm(-1)] species developed, up to approximately 600 Torr of CO(2). However, only the bi- and polydentate carbonate groups still remained on the surface upon outgassing the samples at 323 K. The total amount of adsorbed CO(2), measured by volumetric adsorption (323 K), was approximately 2.0 micromol m(-2) over any of the polymorphs, congruent with an integrated absorbance of (bi)carbonate species proportional to the surface area of the materials. Upon heating under flowing CO(2) (760 Torr), most of the (bi)carbonate species vanished a T > 550 K, but polydentate groups remained on the surface up to the highest temperature used (723 K). A thorough discussion of the more probable surface sites involved in the adsorption of CO(2) is made.