聚硅酸硫酸铁/壳聚糖复合絮凝剂的制备及其在废水处理中的应用

制备了无机高分子复合絮凝剂聚硅酸硫酸铁（PFSS）和助凝剂壳聚糖（CTS）,考察了影响合成及絮凝剂应用的因素,探讨了其组成、投加量以及pH值对城市废水絮凝效果的影响,通过对模拟废水和城市废水絮凝试验,得出最佳的合成和应用条件：n（Fe）∶n（Si）=1∶1,PFSS的碱化度为1.5,聚合硫酸铁（PFS）的pH=2,聚硅酸（PS）的活化时间为1.5 h;n（PFSS）∶n（CTS）=5∶1,投加量为(20+4) mg/L,pH值的范围为6～9,沉降时间为15 min。 复合絮凝剂（PFSS-CTS）在最佳条件下浊度、色度、COD的去除率分别达到95.04%、91.26%和83.45%。     

复合型高效絮凝脱色剂处理印染废水的研究

选用自制的双氰胺甲醛作为絮凝脱色剂处理高浓度印染废水,并与硫酸铝、三氯化铝作了对比实验。考察了投加量、pH值、反应温度等因素对絮凝效果的影响。实验结果表明在用量较少并且其它操作条件相同的情况下,双氰胺甲醛制备的脱色絮凝剂具有很好的絮凝脱色效果及COD_(Cr)去除率。在最佳的操作条件下(投加量120 mg/L,pH=7,反应温度25℃),此脱色絮凝剂对分散、酸性、活性印染废水的COD_(Cr)去除率分别为79.1%、78.5%、79.0%,对分散、酸性、活性印染废水的脱色率分别为94.0%、97.1%、72.9%,减轻了后续处理难度。在与无机絮凝剂的对比试验中,在相同的条件下有机絮凝剂的处理效果总体比无机絮凝剂的处理效果好。     

环氧氯丙烷类阳离子改性絮凝剂的合成及性能研究

为提高环氧氯丙烷胺类絮凝剂的絮凝性能,选用六次甲基四胺为交联剂,以环氧氯丙烷、二甲胺为主要原料,合成了环氧氯丙烷-二甲胺-六次甲基四胺(HMTA)季铵盐阳离子改性絮凝剂,其在辽河油田废水处理中表现出优异的絮凝性能,并研究了絮凝剂用量和温度对HMTA絮凝剂絮凝性能的影响。结果表明,使用HMTA絮凝剂的合适温度为45℃,最佳用量为20mg/L,除浊率可达98. 1%,除油率达到35. 1%。红外光谱和核磁共振谱的表征结果证实六次甲基四胺在聚合物中发挥了交联剂的作用,有效提高了环氧氯丙烷胺类絮凝剂的絮凝性能。     

聚硅硫酸铁絮凝剂去除市政污水磷的研究

将自制复合絮凝剂聚硅硫酸铁(PFSS i)用于市政污水除磷,考察了影响PFSS i除磷效果的一些因素,确定了PFSS i复合絮凝剂除磷的优化配比和用量。在优化条件下,对模拟污水中磷的去除率为96.7%,浊度去除率为92%;对实际污水中磷的去除率为82.3%,浊度去除率为96.5%。结果表明该复合絮凝剂有良好的除磷、除浊性能。     

一种复合脱色剂在印染废水中的应用研究

以甲醛、双氰胺、醋酸钠、氯化铵、氯化铝等为原料制备了一种印染废水脱色絮凝剂T-1。采用福州某纺织印染有限公司的印染废水为处理对象,以脱色率为主要考核指标,讨论了T-1的投加量、pH值、废水温度等对絮凝效果的影响。实验结果表明,双氰胺-甲醛缩聚物对印染废水具有优良的脱色絮凝效果,当投加量为100mg/L,废水温度为30℃,pH=8时,处理效果最佳,色度去除率达70%,COD去除率为78.3%。而且其絮凝性能明显优于聚合氯化铝(PAC)、聚合硫酸铝(PAS)絮凝剂。     

化学混凝法处理废纸制浆废水的研究

在对瓦楞箱板纸废纸制浆废水的特性作了较系统的分析研究的基础上 ,采用自制的混凝剂LPAS及商品絮凝剂聚合氯化铝PAC ,研究了二者的最佳使用条件与对该废水的处理效果 ,结果表明 :混凝剂LPAS比商品絮凝剂PAC对该废水有更好的处理效果 ,当混凝剂LPAS用量为1 50mg/L时 ,废水CODcr、TSS的去除率分别达 71 .8%和 83.6 % ,添加助凝剂FO4 2 4 0可使絮层的沉降速度加快。     

聚合氯化铁的制备及其絮凝效果

以赤铁矿和工业盐酸为原料,采用盐酸酸浸和加碱聚合等方法制取聚合氯化铁絮凝剂(PFC),将其用来处理造纸废水,并与市售聚合氯化铁和碱式氯化铝絮凝剂进行比较.结果表明,在碱化度为2∶1、聚合温度为40℃、陈化时间为24h时,自制聚合氯化铁絮凝剂对造纸废水具有较好的处理效果;投加量为1.4mL/L时,造纸废水的浊度降低了99%,化学需氧量(COD)降低了69.55%,优于市售絮凝剂对造纸废水的处理效果;且三种絮凝剂用量相同时,自制的聚合氯化铁絮凝剂形成絮体的速率和沉降速率都较快.     

木质素阳离子絮凝剂的合成及其絮凝性能研究

以酶解木质素、甲醛、二甲胺及阳离子化试剂为原料,制备了木质素基阳离子絮凝剂.改变阳离子化试剂的用量、缩合反应的温度和时间等因素,制备不同阳离子度的木质素阳离子絮凝剂;通过其对酸性黑10B的脱色效果研究,确定了最优的制备方案.利用最优条件制备的木质素阳离子絮凝剂对三种不同种类阴离子染料废水进行了絮凝脱色处理.结果表明,原...     

淀粉基阳离子絮凝剂的研制及性能测试

用可溶性淀粉为原料,通过接枝改性合成了一种淀粉基阳离子絮凝剂(MSF),其最佳制备工艺条件为:淀粉与丙烯酰胺的质量比为1:2,引发剂用量为0.6 g,反应温度为50 ℃,接枝时间为3.5 h;阳离子化条件为:甲醛和二甲胺摩尔比为1.0:1.4,反应时间2.5 h,反应温度50 ℃.产物结构经FTIR证实.用其处理番茄废水后,废水的透光率提高了78.2%、TOC下降了22.5%、COD下降了37.25%,结果表明该产品对高浓度有机废水的絮凝性能优于聚丙烯酰胺高分子絮凝剂(PAM).     

“氧化·脱色·絮凝”协同法处理含吡啶酮废水

根据染料中间体吡啶-2-酮生产废水的特点,提出了利用“氧化、脱色和絮凝”三位一体的物化方法处理这种废水;探究了搅拌速度、絮凝反应时间、pH值、药剂用量、废水浓度和温度对COD去除率和脱色率的影响,得出了最佳工艺条件.研究结果表明,在常温下,两性聚丙烯酰胺NDPAM用量35 mg/L,氧化交联剂PDO用量0.55 mL/L,pH=5.7,搅拌速度80 r/m in,絮凝时间为15 m in和静止时间为30 m in的条件下,COD的去除率和脱色率均达到98%,处理后的废水达到了可生化的指标范围.并对处理成本和絮凝动力学机理进行了探讨.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.