PPy‐encapsulated SnS2 Nanosheets Stabilized by Defects on a TiO2 Support as a Durable Anode Material for Lithium‐Ion Batteries

Nanostructured‐alloy‐type anodes have received great interest for high‐performance lithium‐ion batteries (LIBs). However, these anodes experience huge volume fluctuations during repeated lithiation/delithiation and are easily pulverized and subsequently form aggregates. Herein, an efficient method to stabilize alloy‐type anodes by creating defects on the surface of the metal oxide support is proposed. As a demonstration, PPy‐encapsulated SnS₂ nanosheets supported on defect‐rich TiO₂ nanotubes were produced and investigated as an anode material for LIBs. Both experimental results and theoretical calculations demonstrate that defect‐rich TiO₂ provides more chemical adhesions to SnS₂ and discharge products, compared to defect‐poor TiO₂, and then effectively stabilizes the electrode structure. As a result, the composite exhibits an unprecedented cycle stability. This work paves the way to designing durable and active nanostructured‐alloy‐type anodes on oxide supports.     

A New Concept for Obtaining SnO2 Fiber‐in‐Tube Nanostructures with Superior Electrochemical Properties

Tin oxide (SnO₂) nanotubes with a fiber‐in‐tube structure have been prepared by electrospinning and the mechanism of their formation has been investigated. Tin oxide‐carbon composite nanofibers with a filled structure were formed as an intermediate product, which were then transformed into SnO₂ nanotubes with a fiber‐in‐tube structure during heat treatment at 500 °C. Nanofibers with a diameter of 85 nm were found to be located inside hollow nanotubes with an outer diameter of 260 nm. The prepared SnO₂ nanotubes had well‐developed mesopores. The discharge capacities of the SnO₂ nanotubes at the 2nd and 300th cycles at a current density of 1 A g^?1 were measured as 720 and 640 mA h g^?1, respectively, and the corresponding capacity retention measured from the 2nd cycle was 88 %. The discharge capacities of the SnO₂ nanotubes at incrementally increased current densities of 0.5, 1.5, 3, and 5 A g^?1 were 774, 711, 652, and 591 mA h g^?1, respectively. The SnO₂ nanotubes with a fiber‐in‐tube structure showed superior cycling and rate performances compared to those of SnO₂ nanopowder. The unique structure of the SnO₂ nanotubes with a fiber@void@tube configuration improves their electrochemical properties by reducing the diffusion length of the lithium ions, and also imparts greater stability during electrochemical cycling.     

General Self‐Template Synthesis of Transition‐Metal Oxide and Chalcogenide Mesoporous Nanotubes with Enhanced Electrochemical Performances

The development of a general strategy for synthesizing hierarchical porous transition‐metal oxide and chalcogenide mesoporous nanotubes, is still highly challenging. Herein we present a facile self‐template strategy to synthesize Co₃O₄ mesoporous nanotubes with outstanding performances in both the electrocatalytic oxygen‐evolution reaction (OER) and Li‐ion battery via the thermal‐oxidation‐induced transformation of cheap and easily‐prepared Co‐Asp(cobalt–aspartic acid) nanowires. The initially formed thin layers on the precursor surfaces, oxygen‐induced outward diffusion of interior precursors, the gas release of organic oxidation, and subsequent Kirkendall effect are important for the appearance of the mesoporous nanotubes. This self‐template strategy of low‐cost precursors is found to be a versatile method to prepare other functional mesoporous nanotubes of transition‐metal oxides and chalcogenides, such as NiO, NiCo₂O₄, Mn₅O₈, CoS₂ and CoSe₂.     

Templated nanostructured PS‐b‐PEO nanotubes

With anodic aluminum oxide (AAO) membranes as wetting templates, nanotubes of the cylinder‐forming polystyrene‐block‐poly(ethylene oxide) (PS‐b‐PEO) copolymer were generated. The PS‐b‐PEO solution was introduced into the cylindrical nanopores of an AAO membrane by capillary force and polymeric nanotubes formed after solvent evaporation. Because of the water solubility of the cylindrical PEO microdomains and the orientation of the cylindrical PEO microdomains with respect to the nanotube walls, the nanotubes were permeable to aqueous media. PS‐b‐PEO nanotubes were also prepared on the interior walls of amorphous carbon nanotubes (a‐CNTs). Because of the unique water permeability of the PEO microdomains, an avenue for functionalizing the interior of the a‐CNTs is enabled. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2912–2917, 2007     

Fe3O4/reduced graphene oxide‐carbon nanotubes composite for the magnetic solid‐phase extraction and HPLC determination of sulfonamides in milk

A novel magnetic adsorbent Fe₃O₄/reduced graphene oxide‐carbon nanotubes, was prepared by one‐pot solvothermal synthesis method. It was characterized by scanning electron microscopy, X‐ray powder diffraction and vibrating sample magnetometry. The diameter of Fe₃O₄ microparticles was about 350 nm, which were covered by carbon nanotubes and reduced graphene oxide sheets, while carbon nanotubes inserted between the reduced graphene oxide sheets effectively prevented their aggregation. The composite had large surface area and good magnetic property, suiting for magnetic solid‐phase extraction and the determination of sulfonamides, by coupling with high‐performance liquid chromatography. Under the optimized conditions (including extraction time, amount of adsorbent, solution pH, ionic strength and desorption conditions), a good linear was achieved in the concentration range of 5–500 μg/L and the low limits of detection and low limits of quantification were 0.35–1.32 and 1.16–4.40 μg/L, respectively. The enrichment factors were estimated to be 24.72 to 30.15 fold. The proposed method was applied for the detection of sulfonamides in milk sample and the recoveries were 88.4–105.9%, with relative standard deviations of 0.74–5.38%.     

TiS2 and ZrS2 single‐ and double‐wall nanotubes: First‐principles study

Hybrid density functional theory has been applied for investigations of the electronic and atomic structure of bulk phases, nanolayers, and nanotubes based on titanium and zirconium disulfides. Calculations have been performed on the basis of the localized atomic functions by means of the CRYSTAL‐2009 computer code. The full optimization of all atomic positions in the regarded systems has been made to study the atomic relaxation and to determine the most favorable structures. The different layered and isotropic bulk phases have been considered as the possible precursors of the nanotubes. Calculations on single‐walled TiS₂ and ZrS₂ nanotubes confirmed that the nanotubes obtained by rolling up the hexagonal crystalline layers with octahedral 1T morphology are the most stable. The strain energy of TiS₂ and ZrS₂ nanotubes is small, does not depend on the tube chirality, and approximately obeys to D^–2 law (D is nanotube diameter) of the classical elasticity theory. It is greater than the strain energy of the similar TiO₂ and ZrO₂ nanotubes; however, the formation energy of the disulfide nanotubes is considerably less than the formation energy of the dioxide nanotubes. The distance and interaction energy between the single‐wall components of the double‐wall nanotubes is proved to be close to the distance and interaction energy between layers in the layered crystals. Analysis of the relaxed nanotube shape using radial coordinate of the metal atoms demonstrates a small but noticeable deviation from completely cylindrical cross‐section of the external walls in the armchair‐like double‐wall nanotubes. © 2013 Wiley Periodicals, Inc.     

Wintersweet‐Flower‐Like CoFe2O4/MWCNTs Hybrid Material for High‐Capacity Reversible Lithium Storage

CoFe₂O₄/multiwalled carbon nanotubes (MWCNTs) hybrid materials were synthesized by a hydrothermal method. Field emission scanning electron microscopy and transmission electron microscopy analysis confirmed the morphology of the as‐prepared hybrid material resembling wintersweet flower “buds on branches”, in which CoFe₂O₄ nanoclusters, consisting of nanocrystals with a size of 5–10 nm, are anchored along carbon nanotubes. When applied as an anode material in lithium ion batteries, the CoFe₂O₄/MWCNTs hybrid material exhibited a high performance for reversible lithium storage. In particular, the hybrid anode material delivered reversible lithium storage capacities of 809, 765, 539, and 359 mA h g^?1 at current densities of 180, 450, 900, and 1800 mA g^?1, respectively. The superior performance of CoFe₂O₄/MWCNTs hybrid materials could be ascribed to the synergistic pinning effect of the wintersweet‐flower‐like nanoarchitecture. This strategy could also be applied to synthesize other metal oxide/CNTs hybrid materials as high‐capacity anode materials for lithium ion batteries.     

Lanthanide‐Based Functional Misfit‐Layered Nanotubes

The synthesis of nanotubes from layered compounds has generated substantial scientific interest. “Misfit” layered compounds (MLCs) of the general formula [(MX)_1+x]_m[TX₂]_n, where M can include Pb, Sb, rare earths; T=Cr, Nb, and X=S, Se can form layered structures, even though each sub‐system alone is not necessarily a layered or a stable compound. A simple chemical method is used to synthesize these complex nanotubes from lanthanide‐based misfit compounds. Quaternary nanotubular structures formed by partial substitution of the lanthanide atom in nanotubes by other elements are also confirmed. The driving force and mechanism of formation of these nanotubes is investigated by systematic temperature and time‐dependent studies. A stress‐inducement mechanism is proposed to explain the formation of the nanotubes. The resulting materials may find applications in fields that include thermoelectrics, light emitters, and catalysis and address fundamental physical issues in low dimensions.     

Single‐Walled Carbon Nanotubes in Highly Viscous Media: A Comparison between the Dispersive Agents [BMIM][BF4], L121, and Triton X‐100

Dispersions of single‐walled carbon nanotubes (SWNTs) have been prepared by using the room‐temperature ionic liquid [BMIM][BF₄] (1‐butyl‐3‐methylimidazolium tetrafluoroborate), the triblock copolymer Pluronic L121 [poly(ethylene oxide)₅‐poly(propylene oxide)₆₈‐poly(ethylene oxide)₅] and the non‐ionic surfactant Triton X‐100 (TX100) in the pure state. The size of the SWNTs aggregates and the dispersion degree in the three viscous systems depend on the sonication time, as highlighted by UV/Vis/NIR spectroscopy and optical microscopy analysis. A nonlinear increase in conductivity can be observed as a function of the SWNTs loading, as suggested by electrochemical impedance spectroscopy. The generation of a three‐dimensional network of SWNTs showing a viscoelastic gel‐like behavior above a critical percolation concentration has been found at 25 °C in all the investigated systems by oscillatory rheology measurements.     

Tailoring Transition‐Metal Hydroxides and Oxides by Photon‐Induced Reactions

Controlled synthesis of transition‐metal hydroxides and oxides with earth‐abundant elements have attracted significant interest because of their wide applications, for example as battery electrode materials or electrocatalysts for fuel generation. Here, we report the tuning of the structure of transition‐metal hydroxides and oxides by controlling chemical reactions using an unfocused laser to irradiate the precursor solution. A Nd:YAG laser with wavelengths of 532 nm or 1064 nm was used. The Ni²⁺, Mn²⁺, and Co²⁺ ion‐containing aqueous solution undergoes photo‐induced reactions and produces hollow metal‐oxide nanospheres (Ni_0.18Mn_0.45Co_0.37O_x) or core–shell metal hydroxide nanoflowers ([Ni_0.15Mn_0.15Co_0.7(OH)₂](NO₃)_0.2?H₂O), depending on the laser wavelengths. We propose two reaction pathways, either by photo‐induced redox reaction or hydrolysis reaction, which are responsible for the formation of distinct nanostructures. The study of photon‐induced materials growth shines light on the rational design of complex nanostructures with advanced functionalities.     

Three‐Dimensional Nitrogen‐Doped Reduced Graphene Oxide–Carbon Nanotubes Architecture Supporting Ultrafine Palladium Nanoparticles for Highly Efficient Methanol Electrooxidation

A three‐dimensional (3D) nitrogen‐doped reduced graphene oxide (rGO)–carbon nanotubes (CNTs) architecture supporting ultrafine Pd nanoparticles is prepared and used as a highly efficient electrocatalyst. Graphene oxide (GO) is first used as a surfactant to disperse pristine CNTs for electrochemical preparation of 3D rGO@CNTs, and subsequently one‐step electrodeposition of the stable colloidal GO–CNTs solution containing Na₂PdCl₄ affords rGO@CNTs‐supported Pd nanoparticles. Further thermal treatment of the Pd/rGO@CNTs hybrid with ammonia achieves not only in situ nitrogen‐doping of the rGO@CNTs support but also extraordinary size decrease of the Pd nanoparticles to below 2.0 nm. The resulting catalyst is characterized by scanning and transmission electron microscopy, X‐ray diffraction, Raman spectroscopy, and X‐ray photoelectron spectroscopy. Catalyst performance for the methanol oxidation reaction is tested through cyclic voltammetry and chronoamperometry techniques, which shows exceedingly high mass activity and superior durability.     

Low‐Temperature Synthesis of Crystalline Inorganic/Metallic Nanocrystal‐Halloysite Composite Nanotubes

We have demonstrated a facile approach for the low‐temperature synthesis of crystalline inorganic/metallic nanocrystal‐halloysite composite nanotubes by employing the bulk controlled synthesis of inorganic/metallic nanocrystals on halloysite nanotubes. The halloysite clay nanotubes can adsorb the target precursor and induce inorganic/metallic nanocrystals to grow in situ. The crystalline phase and morphology of the composite clay nanotubes is tunable. By simply tuning the acidity of the titania sol, the crystalline titania‐clay nanotubes with tunable crystalline phases of anatase, a mixture of anatase and rutile or rutile are achieved. The approach is general and has been extended to synthesize the representative perovskite oxide (barium and strontium titanate)‐halloysite composite nanotubes. Metallic nickel nanocrystal can also be grown on the surface of halloysite nanotubes at low temperature. The traditional thermal treatment for crystallite transformation is not required, thus intact contour of halloysite nanotubes and the crystallinity structure of halloysite nanotubes can be guaranteed. The combined properties from inorganic/metallic nanocrystal (high refractive index, high dielectric constant and catalytic ability) and the halloysite clay nanotubes are promising for applications such as photonic crystals, high‐k‐gate dielectrics, photocatalysis and purification.     

One‐Step Solvothermal Synthesis of Single‐Crystalline TiOF2 Nanotubes with High Lithium‐Ion Battery Performance

Single‐crystalline TiOF₂ nanotubes were prepared by a one‐step solvothermal method. The nanotubes are rectangular in shape with a length of 2–3 μm, width of 200–300 nm, and wall thickness of 40–60 nm. The formation of TiOF₂ nanotubes is directly driven by the interaction between TiF₄ and oleic acid in octadecane to form the 1D nanorods, and this is followed by a mass diffusion process to form the hollow structures. The synthesis approach can be extended to grow TiOF₂ nanoparticles and nanorods. Compared with TiO₂, which is the more commonly considered anode material in lithium‐ion batteries, TiOF₂ has the advantages of a lower Li‐intercalation voltage (e.g., to help increase the total voltage of the battery cell) and higher specific capacities. The TiOF₂ nanotubes showed good Li‐storage properties with high specific capacities, stable cyclabilities, and good rate capabilities.     

Aligned MoOx/MoS2 Core–Shell Nanotubular Structures with a High Density of Reactive Sites Based on Self‐Ordered Anodic Molybdenum Oxide Nanotubes

The present work demonstrates the self‐organized formation of anodic molybdenum oxide nanotube arrays. The amorphous tubes can be crystallized to MoO₂ or MoO₃ and be converted fully or partially into molybdenum sulfide. Vertically aligned MoO_x/MoS₂ nanotubes can be formed when, under optimized conditions, defined MoS₂ sheets form in a layer by layer arrangement that provide a high density of reactive stacking misalignments (defects). These core–shell nanotube arrays consist of a conductive suboxide core and a functional high defect density MoS₂ coating. Such structures are highly promising for applications in electrocatalysis (hydrogen evolution) or ion insertion devices.     

First‐principles modeling of hafnia‐based nanotubes

Hybrid density functional theory calculations were performed for the first time on structure, stability, phonon frequencies, and thermodynamic functions of hafnia‐based single‐wall nanotubes. The nanotubes were rolled up from the thin free layers of cubic and tetragonal phases of HfO₂. It was shown that the most stable HfO₂ single‐wall nanotubes can be obtained from hexagonal (111) layer of the cubic phase. Phonon frequencies have been calculated for different HfO₂ nanolayers and nanotubes to prove the local stability and to find the thermal contributions to their thermodynamic functions. The role of phonons in stability of nanotubes seems to be negligible for the internal energy and noticeable for the Helmholtz free energy. Zone folding approach has been applied to estimate the connection between phonon modes of the layer and nanotubes and to approximate the nanotube thermodynamic properties. It is found that the zone‐folding approximation is sufficiently accurate for heat capacity, but less accurate for entropy. The comparison has been done between the properties of TiO₂, ZrO₂, and HfO₂. © 2017 Wiley Periodicals, Inc.     

Amine‐Appended Hierarchical Ca‐A Zeolite for Enhancing CO2/CH4 Selectivity of Mixed‐Matrix Membranes

An amine‐appended hierarchical Ca‐A zeolite that can selectively capture CO₂ was synthesized and incorporated into inexpensive membrane polymers, in particular polyethylene oxide and Matrimid, to design mixed‐matrix membranes with high CO₂/CH₄ selectivities. Binary mixture permeation testing reveals that amine‐appended mesoporous Ca‐A is highly effective in improving CO₂/CH₄ selectivity of polymeric membranes. In particular, the CO₂/CH₄ selectivity of the polyethylene oxide membrane increases from 15 to 23 by incorporating 20 wt % amine‐appended Ca‐A zeolite. Furthermore, the formation of filler/polymer interfacial defects, which is typically found in glassy polymer‐zeolite pairs, is inhibited owing to the interaction between the amine groups on the external surface of zeolites and polymer chains. Our results suggest that the amine‐appended hierarchial Ca‐A, which was utilized in membrane fabrication for the first time, is a good filler material for fabricating a CO₂‐selective mixed‐matrix membrane with defect‐free morphology.     

Defect‐Free Mixed‐Matrix Membranes with Hydrophilic Metal‐Organic Polyhedra for Efficient Carbon Dioxide Separation

Defect‐free mixed‐matrix membranes (MMMs) were prepared by incorporating hydrophilic metal‐organic polyhedra (MOPs) into cross‐linked polyethylene oxide (XLPEO) for efficient CO₂ separation. Hydrophilic MOPs with triethylene glycol pendant groups, which were assembled by 5‐tri(ethylene glycol) monomethyl ether isophthalic acid and Cu^II ions, were uniformly dispersed in XLPEO without particle agglomeration. Compared to conventional neat XLPEO, the homogenous dispersion of EG₃‐MOPs in XLPEO enhanced CO₂ permeability of MMMs. Upon increasing the amount of EG₃‐MOPs, the membrane performance such as CO₂/N₂ selectivity was steadily improved because of unsaturated Cu^II sites at paddle‐wheel units, which was confirmed by Cu K‐edge XANES and TPD analysis. Therefore, such defect‐free MMMs with unsaturated metal sites would contribute to enhance CO₂ separation performance.     

Facile Synthesis of High‐Quality Plasma‐Reduced Graphene Oxide with Ultrahigh 4,4′‐Dichlorobiphenyl Adsorption Capacity

High‐quality reduced graphene, termed PG, has been synthesized by a simple, low‐cost, and green plasma approach, and applied as adsorbent to remove 4,4′‐dichloribiphenyl (4,4′‐DCB) from aqueous solutions. As a comparison, the adsorption of 4,4′‐DCB on graphene oxide (GO) and multiwalled carbon nanotubes (MWCNTs) was also studied under the same experimental conditions. PG performs significantly better with regard to 4,4′‐DCB adsorption than GO and MWCNTs, or any reported nanomaterials, with a maximum adsorption capacity (q_max) of 1552 mg g^?1 at pH 7.0. The high affinity of 4,4′‐DCB to PG is mainly a result of strong π–π interactions, as also confirmed by DFT calculations. The results reveal that PG sheets hold promise for the removal of persistent organic pollutants. We expect possible applications of this fast and mild plasma technique in the fabrication of nanomaterials and envisage their use in a variety of advanced chemical processes.     

Cooperative Self‐Assembly of Pyridine‐2,6‐Diimine‐Linked Macrocycles into Mechanically Robust Nanotubes

Nanotubes assembled from macrocyclic precursors offer a unique combination of low dimensionality, structural rigidity, and distinct interior and exterior microenvironments. Usually the weak stacking energies of macrocycles limit the length and mechanical strength of the resultant nanotubes. Imine‐linked macrocycles were recently found to assemble into high‐aspect ratio (>10³), lyotropic nanotubes in the presence of excess acid. Yet these harsh conditions are incompatible with many functional groups and processing methods, and lower acid loadings instead catalyze macrocycle degradation. Here we report pyridine‐2,6‐diimine‐linked macrocycles that assemble into high‐aspect ratio nanotubes in the presence of less than 1 equiv of CF₃CO₂H per macrocycle. Analysis by gel permeation chromatography and fluorescence spectroscopy revealed a cooperative self‐assembly mechanism. The low acid concentrations needed to induce assembly enabled nanofibers to be obtained by touch‐spinning, which exhibit higher Young's moduli (1.33 GPa) than many synthetic polymers and biological filaments. These findings represent a breakthrough in the design of inverse chromonic liquid crystals, as assembly under such mild conditions will enable the design of structurally diverse and mechanically robust nanotubes from synthetically accessible macrocycles.     

Electrospun V2O5 Nanostructures with Controllable Morphology as High‐Performance Cathode Materials for Lithium‐Ion Batteries

Porous V₂O₅ nanotubes, hierarchical V₂O₅ nanofibers, and single‐crystalline V₂O₅ nanobelts were controllably synthesized by using a simple electrospinning technique and subsequent annealing. The mechanism for the formation of these controllable structures was investigated. When tested as the cathode materials in lithium‐ion batteries (LIBs), the as‐formed V₂O₅ nanostructures exhibited a highly reversible capacity, excellent cycling performance, and good rate capacity. In particular, the porous V₂O₅ nanotubes provided short distances for Li⁺‐ion diffusion and large electrode–electrolyte contact areas for high Li⁺‐ion flux across the interface; Moreover, these nanotubes delivered a high power density of 40.2 kW kg^?1 whilst the energy density remained as high as 201 W h kg^?1, which, as one of the highest values measured on V₂O₅‐based cathode materials, could bridge the performance gap between batteries and supercapacitors. Moreover, to the best of our knowledge, this is the first preparation of single‐crystalline V₂O₅ nanobelts by using electrospinning techniques. Interestingly, the beneficial crystal orientation provided improved cycling stability for lithium intercalation. These results demonstrate that further improvement or optimization of electrochemical performance in transition‐metal‐oxide‐based electrode materials could be realized by the design of 1D nanostructures with unique morphologies.