Direct colorimetric detection of copper(II) ions in sampling using diffusive gradients in thin-films

A novel binding phase was developed for use in diffusive gradients in thin-film (DGT) sampling for Cu(II) by employing methylthymol blue as a chelating and chromogenic agent. Methylthymol blue was adsorbed onto beads of Dowex 1 × 8 resin (200-400 mesh) and the resin beads were then immobilised onto an adhesive disc. Analysis of exposed binding discs by either UV-vis spectrophotometry or computer imaging densitometry provided robust quantification of adsorbed Cu(II) in the 0.2-1 μg cm⁻² range, allowing detection at μg L⁻¹ concentrations in the test solution (ca. 17 μg L⁻¹ for a 24 h deployment), and in good agreement with established DGT theory. The method was shown to be a potential replacement for binding phases based on Chelex 100 where a colorimetric response to a specific metal is desired.     

A multi-syringe flow injection system for the spectrophotometric determination of trace levels of iron in waters using a liquid waveguide capillary cell and different chelating resins and reaction chemistries

A method integrating a long waveguide capillary cell with a preconcentration resin in a multi-syringe flow injection analysis (MSFIA) system for iron determination in waters was developed. The determination of iron is based on a colorimetric reaction and two reagents were tested, ferrozine and ammonium thiocyanate. A liquid waveguide capillary cell (1.0 m pathlength, 550 µm i.d. and 250 µL internal volume) with a preconcentration resin were used to improve the sensitivity of the determination. Two different preconcentration resins were also tested, Chelex 100 and NTA Superflow. The developed method employing the NTA Superflow with ferrozine colorimetric reagent provided a detection limit of 0.05 µg L^− 1 with a linear response up to 8 µg L^− 1 and a sample throughput rate of 12 per hour. The developed system presents low reagents/sample consumptions. The accuracy was assessed using a certified reference water sample.     

Exploiting the bead injection concept for sequential determination of copper and mercury ions in river-water samples

A procedure involving bead-injection concept and sequential determination of copper and mercury ions in river-water samples is proposed. The method is based on the solid-phase extraction of both metal ions on the same beads surface (Chelex 100 resin) and in their subsequent reaction with the colorimetric reagents (APDC and Dithizone for copper and mercury ions, respectively). For this task, a resin mini-column is established in the optical path by the selection, introduction and trapping of a defined volume of the Chelex-100 resin beads suspension in the flow system. The passage of the sample solution through the resin mini-column promotes the sorption of Cu(II) ions and, making the APDC colorimetric reagent flows through the beads, the formation of the coloured complex on the solid phase surface occurs. The absorbance of the formed APDC-Cu complex is then monitored at 436 nm and the spent beads are discarded. Packing another resin mini-column in the flow cell and repeating the concentration step it is possible to carried out the mercury determination by using Dithizone as reagent. The absorbance of the Dithizone-Hg complex is monitored at 500 nm. After each measurement, the spent beads are wasted and a new portion of fresh one is trapped in the system, letting it ready for the next measurement. The bead injection system is versatile and can be used to concentrate different sample volumes, which permits the determination of a wide range of copper and mercury ions concentrations. When the sample-selected volumes are 100 and 1000 μl the analytical ranges were 5.0 up to 500.0 μg l⁻¹ and 2.5 up to 30.0 μg l⁻¹ for Cu(II) and Hg(II) ions, respectively. Under these conditions, the detection limit was estimated as 0.63 and 0.25 μg l⁻¹ for copper and mercury ions determination. The system consumes 2 mg of Chelex 100 resin beads, 0.20 mg of APDC or 1.25 mg of Dithizone per determination and the traditional organic solvent extraction methodology, normally used in connection with APDC and Dithizone reagents, is not used here which permits to classify the present method as green.     

Solid-phase iodine as an oxidant in flow injection analysis: determination of ascorbic acid in pharmaceuticals and foods by background correction

A flow injection analysis (FIA)-background correction method comprising two solid-phase reactors and spectrophotometry for determination of ascorbic acid (AsA) is proposed. A polyethylene mini-column filled with solid iodine (30% m/m suspended on silica gel beads), reactor 1, and other column filled only with silica gel, reactor 2, which are then incorporated in a flow system so that solid iodine reagent in reactor 1 is affected as the sample passes through the column. The sample blank is produced by the oxidation of the AsA by iodine to form dehydroascorbic acid, insensitive to ultraviolet at 267 nm. AsA in samples is determined after injected in reactor 2; the difference in two analytical signal observed is related to amount of AsA. The linear range of the system is up to 50 μg ml⁻¹ with a detection limit of 0.08 μg ml⁻¹, R.S.D. of better than 1.0% and sampling frequency of 110 sample h⁻¹. The method is successfully applied to the determination of AsA in pharmaceuticals and foods.     

Solid-phase UV spectrophotometric method for determination of ciprofloxacin

A simple and inexpensive method for the determination of ciprofloxacin has been developed using solid-phase spectrophotometry. The intrinsic absorbance of ciprofloxacin fixed on a dextran-type cation-exchange resin, Sephadex SP C-25, was measured directly at 277 and 380 nm after packing the gel beads in a 1-mm cell. Using a sample volume of 10 ml, the calibration graph was linear over the range 0.05-0.3 μg ml⁻¹ with a R.S.D. of 1.11% (n=8). The sensitivity obtained is 40 times higher than that of the corresponding solution method. The method was applied to the determination of ciprofloxacin in pharmaceutical preparations and was validated by standard addition.     

Study on New Sensitive Method of Determination of Phosphorus by Solid Phase Spectrophotometry

IntroductionThespectrophotometricdeterminationofphosphoruswithcoloursystemcomposedofphosphomolybdate-fructoseinaqueousphasehasbeenreportedI'2.Itwasfoundthatthiscoloursystemwaseasilyadsorbedontheanion-exchangeresin(2O-4Omesh,CLform),hence,anewmethodofdeterminationoftracephosphoruswasestablishedbysolidphasespectrophotometry.Insolutionofsulfuricacid,phosphorusreactswithammoniummolybdatetoformphosphomolybdateyellowwhichisreducedintophosphomolybdatebluebyfructose,thephosphomolybdatebluecanbequant…     

Interfacial reaction using particle-immobilized reagents in a fluidized reactor. Determination of glycerol in biodiesel

A novel fluidized beads strategy for utilization of particle-immobilized reagents in flow analysis was developed in this study. The performance of the suggested strategy was demonstrated by the determination of glycerol in biodiesel. This analytical task was used as a proof-of-concept example. The method is based on on-line extraction of glycerol from biodiesel into aqueous stationary phase of extraction-chromatographic column, followed by elution and spectrophotometric determination in the form of copper glycerate formed in a fluidized reactor of stepwise injection system. The floating of cation exchange resin Dowex^® 50WX4, saturated with Cu(II) ions in liquid phase, was accomplished by air-bubbling. The linear range was from 100 to 1000 mg kg⁻¹, and the limit of detection, calculated as 3s of a blank test (n = 5), was found to be 30 mg kg⁻¹. The method was successfully applied to the analysis of biodiesel and biodiesel-blend (B 20) samples.     

Detection and Spectrophotometric Determination of Microgram Quantities of Ethylenediaminetetraacetic Acid with Phosphomolybdic Acid

Abstract

A simple, rapid and accurate method for the detection and determination of microgram quantities of EDTA is based on the absorbance of the complex formed by its reaction with phosphomolybdic acid at pH 2. Absorbance is measured against a phosphomolybdic acid reference solution at a wave length of 690 am. The effect of time, temperature and amount of phosphomolybdic acid is studied and optimum operating conditions established. Beer's law is obeyed in the concentration range 18.6–186.0 μg ml^?1 of EDTA. Its detection limit is 18.6 μg in the solution phase and 3.72 μg in the resin phase. The relative standard deviation is ±0.445 μg. Ion exchange resin beads act as a catalyst and detection medium to improve the sensitivity and selectivity of the test.     

STUDY ON THE DETERMINATION OF TRACE BISMUTH(Ⅲ) BY THIN-LAYER RESIN PHASE SPECTROPHOTOMETRY

In this paper, a new thin-layer ion-exchange resin phase analytical method is introduced. It is based on that, the bismuthous cation can associate with iodic anions, so as to formed an anioncomplex [BiI-4] in a strong acidic environments. This anion complex can also exchanges with a weaker anions on the surface active site of anion exchange resin, so that a [R+] [BiI-4] solid phase binary associational system is produced. Owing to the solid system is a great many dispersive particulates, it can be pressed to a thin-layer by press tools of the so called "thin-layer resin phase"or "resin phase ", and using this solid association system spectrophotometry for the determination of trace metals. So it can increase the analytical sensitivity. This association system exhibits maximum absorbance at 460nm, and obeys Beer's law over the concentration range 0. 01ug/ml～1.20ug/ml of bismuthous(Ⅲ). It has a molar absorptivity of 7.1 ×105 [L/mol cm]. It indicated the resin phase spectrophotometry is a sensitive analytical method for trace bismuthous. It is 18 times higher than routine aqueous spectrophotometry. The relative standard deviations is 1.82% (n=6) for the measurements of 0. 5ug/ml Bi(Ⅲ). The detection limit of Bismuthous(Ⅲ) is 1.4 ×10-8mol/L. The method has applied to the analysis Bi(Ⅲ) in environmental water samples.     

STUDY ON DETERMINATION OF TRACE Cu（Ⅱ） BY DDCT CHELATING RESIN PRECONCENTRATION AND THIN LAYER RESIN PHASE SPECTROPHOTOMETRY

A new method for determination of Cu(Ⅱ) by DDCT chelating resin preconcentration and thin layer resin phase spectrophotometry was developed. The method has a high sensitivity (ε435 =3.6×105 L/mol· cm), which is 33 times higher than that of liquid phase spectrophotometry. It has a good selectivity (most coexisting ions could not influence determination) and an ideal precision [30μg Cu(Ⅱ), n=6, RSD= 1.67%]. The content of Cu(Ⅱ) in water, high purity rare earth and its oxide was determined. The detection limit of Cu(Ⅱ) is 5.3μg/L, and the linear range is 0～7.2 μg/ml. The result is satisfactory.     

Polypyrrole‐magnetite dispersive micro‐solid‐phase extraction combined with ultraviolet‐visible spectrophotometry for the determination of rhodamine 6G and crystal violet in textile wastewater

Polypyrrole‐magnetite dispersive micro‐solid‐phase extraction method combined with ultraviolet‐visible spectrophotometry was developed for the determination of selected cationic dyes in textile wastewater. Polypyrrole‐magnetite was used as adsorbent due to its thermal stability, magnetic properties, and ability to adsorb Rhodamine 6G and crystal violet. Dispersive micro‐solid‐phase extraction parameters were optimized, including sample pH, adsorbent amount, extraction time, and desorption solvent. The optimum polypyrrole‐magnetite dispersive micro‐solid phase‐extraction conditions were sample pH 8, 60 mg polypyrrole‐magnetite adsorbent, 5 min of extraction time, and acetonitrile as the desorption solvent. Under the optimized conditions, the polypyrrole‐magnetite dispersive micro‐solid‐phase extraction with ultraviolet‐visible method showed good linearity in the range of 0.05–7 mg/L (R ² > 0.9980). The method also showed a good limit of detection for the dyes (0.05 mg/L) and good analyte recoveries (97.4–111.3%) with relative standard deviations < 10%. The method was successfully applied to the analysis of dyes in textile wastewater samples where the concentration found was 1.03 mg (RSD ±7.9%) and 1.13 mg/L (RSD ± 4.6%) for Rhodamine 6G and crystal violet, respectively. It can be concluded that this method can be adopted for the rapid extraction and determination of dyes at trace concentration levels.     

固相分光光度法测定水中痕量磷

固相分光光度法是一种简单、快速、灵敏的新型痕量分析手段。本文首次提出利用氯型阴离子交换树脂做固体吸附剂,采用“模型压片法”测定水中痕量磷。结果令人满意。     

Fe3O4 nanoparticles coated with polyhedral oligomeric silsesquioxanes and β‐cyclodextrin for magnetic solid‐phase extraction of carbaryl and carbofuran

In this study, porous sandwich structure Fe₃O₄ nanoparticles coated by polyhedral oligomeric silsesquioxanes and β‐cyclodextrin were prepared by surface polymerization and were used as the magnetic solid phase extraction adsorbent for the extraction and determination of carbaryl and carbofuran. The Fe₃O₄ nanoparticles coated with polyhedral oligomeric silsesquioxanes and β‐cyclodextrin were characterized by Fourier transform infrared spectroscopy, X‐ray diffraction, thermogravimetric analysis, vibrating sample magnetometry, and scanning electron microscopy. After optimizing the extraction conditions, a method that combined magnetic solid phase extraction with high‐performance liquid chromatography was developed for the determination of carbaryl and carbofuran in apple. The method exhibited a good linearity in the range of 2–400 μg/kg for carbaryl and carbofuran (R² = 0.9995), respectively. The limits of detection were 0.5 μg/kg of carbaryl and 0.7 μg/kg for carbofuran in apple, respectively. Extraction recoveries ranged from 94.2 to 103.1% with the preconcentration factor of 300 and the relative standard deviations were less than 5.9%. These results indicated that the method combined magnetic solid phase extraction with high‐performance liquid chromatography and was promising for the determination of carbaryl and carbofuran at trace amounts.     

Development of a novel mixed hemimicelles dispersive micro solid phase extraction using 1-hexadecyl-3-methylimidazolium bromide coated magnetic graphene for the separation and preconcentration of fluoxetine in different matrices before its determination by fiber optic linear array spectrophotometry and mode-mismatched thermal lens spectroscopy

This study aims at developing a novel, sensitive, fast, simple and convenient method for separation and preconcentration of trace amounts of fluoxetine before its spectrophotometric determination. The method is based on combination of magnetic mixed hemimicelles solid phase extraction and dispersive micro solid phase extraction using 1-hexadecyl-3-methylimidazolium bromide coated magnetic graphene as a sorbent. The magnetic graphene was synthesized by a simple coprecipitation method and characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM). The retained analyte was eluted using a 100 μL mixture of methanol/acetic acid (9:1) and converted into fluoxetine-β-cyclodextrin inclusion complex. The analyte was then quantified by fiber optic linear array spectrophotometry as well as mode-mismatched thermal lens spectroscopy (TLS). The factors affecting the separation, preconcentration and determination of fluoxetine were investigated and optimized. With a 50 mL sample and under optimized conditions using the spectrophotometry technique, the method exhibited a linear dynamic range of 0.4–60.0 μg L⁻¹, a detection limit of 0.21 μg L⁻¹, an enrichment factor of 167, and a relative standard deviation of 2.1% and 3.8% (n = 6) at 60 μg L⁻¹ level of fluoxetine for intra- and inter-day analyses, respectively. However, with thermal lens spectrometry and a sample volume of 10 mL, the method exhibited a linear dynamic range of 0.05–300 μg L⁻¹, a detection limit of 0.016 μg L⁻¹ and a relative standard deviation of 3.8% and 5.6% (n = 6) at 60 μg L⁻¹ level of fluoxetine for intra- and inter-day analyses, respectively. The method was successfully applied to determine fluoxetine in pharmaceutical formulation, human urine and environmental water samples.     

Cellulose membrane modified with polypyrrole as an extraction device for the determination of emerging contaminants in river water with gas chromatography–mass spectrometry

In this study, a simple, efficient, and reusable device based on cellulose membranes modified with polypyrrole was developed to extract 14 emerging contaminants from aqueous matrices. For chemical polymerization, a low‐cost cellulose membrane was immersed in 0.1 mol/L pyrrole and 0.5 mol/L ammonium persulfate for 40 min in an ice/water bath. The cellulose membranes modified with polypyrrole were accommodated in a polycarbonate holder suitable for solid‐phase extraction disks. Solid‐phase extraction parameters that affect extraction efficiency, such as sample volume, pH, flow rate, and desorption were optimized. Subsequently, determination of target compounds was performed by gas chromatography with mass spectrometry. The linear range for analytes ranged from 0.05 to 500 μg/L, with coefficients of determination above 0.990. The limits of quantification varied between 0.05 and 10 μg/L, with relative standard deviations lower than 17%. The performance of the proposed cellulose membranes modified with polypyrrole device for real samples was evaluated after extraction of emerging contaminants from a river water sample from the city of Curitiba, Brazil. Bisphenol A (6.39 μg/L), caffeine (17.83 μg/L), and paracetamol (19.28 μg/L) were found in these samples.     

A continuous flow system combined with a sensing fluorimetric transductor for the determination of β-naphthol

A single automatic method for continuous flow determination of β-naphthol based on the enhancement of its native fluorescence once the analyte was transitorily retained on-line on a solid support (QAE A-25 resin) is reported. So, a flow-through optosensor was developed using a flow-injection analysis system with solid phase fluorimetric transduction. KCl (0.15 mol l⁻¹) at pH 12.0 was used as carrier solution. To obtain the optimum fluorescence signal the wavelengths chosen were 245 nm (excitation) and 420 nm (emission). The response of the sensor was directly proportional to the sample volume injected in the studied range 40-1500 μl. Approximately one higher order of magnitude is achieved in sensitivity when 1500 μl are used with respect to the use of 40 μl of sample. The sensor was calibrated for three different injection volumes: 40, 600 and 1500 μl, responding linearly in the measuring range of 2-60, 0.5-15 and 0.2-5 μg l⁻¹ with detection limits of 0.5, 0.09 and 0.05 μg l⁻¹, respectively. The relative standard deviation for ten independent determination is 0.6% (40 μl), 0.9% (600 μl) and 2.3% (1500 μl). A recovery study was performed onto three different spiked water samples at concentration levels from 1 to 2.5 μg l⁻¹ and the recovery percentage from the experimental data ranged between 101±2 and 105±5.     

Exploiting the bead injection LOV approach to carry out spectrophotometric assays in wine: application to the determination of iron

A sequential injection lab-on-valve (SI-LOV) system was used to develop a new methodology for the determination of iron in wine samples exploiting the bead injection (BI) concept for solid phase extraction and spectrophotometric measurement. Nitrilotriacetic Acid (NTA) Superflow resin was used to build the bead column of the flow through sensor. The iron (III) ions were retained by the bead column and react with SCN⁻ producing an intense red colour. The change in absorbance was monitored spectrophotometrically on the optosensor at 480 nm. It was possible to achieve a linear range of 0.09-5.0 mg L⁻¹ of iron, with low sample and reagent consumption; 500 μL of sample, 15 μmol of SCN⁻, and 9 μmol of H₂O₂, per assay. The proposed method was successfully applied to the determination of iron in wine, with no previous treatment other than dilution, and to other food samples.     

Photoacoustic spectrometric determination of trace phosphorus as molybdenum blue adsorbed on uniform anion-exchange beads

Photoacoustic spectrometry was applied to the determination of phosphorus as molybdenum blue species adsorbed on an anion-exchange resin (10 mg of uniform beads). The photoacoustic intensity of ten resin particles on a glass plate was measured at 760 nm. The calibration graph obtained was linear in the range of 0.05–0.5 μg of phosphorus. The relative standard deviation for ten determinations of 0.3 μg P was 5.0%. The detection limit was 2 ng P ml^?1.     

A Bead Injection System for Copper Determination

ABSTRACT

A bead injection system for copper determination is proposed. Chelex-100 resin beads are introduced in the system as a suspension that is trapped in the Jet Ring Cell. The passage of the sample zone by the beads promotes the sorption of Cu(II). When the colorimetric reagent (APDC) perfuses the beads it reacts with copper ions, forming a colored complex that is monitored at 436 nm. After the measurement, the spent beads are sent to waste and a new portion of fresh beads is trapped in the system. The bead injection system is versatile and can be used to concentrate analyte in different sample volumes, permitting determinations of a wide range of copper concentrations. The detection limit is 0.5 μg l^-1 with a 500 μl sample, and 1.2 μg l^-1 with a 100 μ1 sample.     

Magnetic micro‐solid‐phase extraction based on magnetite‐MCM‐41 with gas chromatography–mass spectrometry for the determination of antidepressant drugs in biological fluids

A new facile magnetic micro‐solid‐phase extraction coupled to gas chromatography and mass spectrometry detection was developed for the extraction and determination of selected antidepressant drugs in biological fluids using magnetite‐MCM‐41 as adsorbent. The synthesized sorbent was characterized by several spectroscopic techniques. The maximum extraction efficiency for extraction of 500 μg/L antidepressant drugs from aqueous solution was obtained with 15 mg of magnetite‐MCM‐41 at pH 12. The analyte was desorbed using 100 μL of acetonitrile prior to gas chromatography determination. This method was rapid in which the adsorption procedure was completed in 60 s. Under the optimized conditions using 15 mL of antidepressant drugs sample, the calibration curve showed good linearity in the range of 0.05–500 μg/L (r ² = 0.996–0.999). Good limits of detection (0.008–0.010 μg/L) were obtained for the analytes with good relative standard deviations of <8.0% (n  = 5) for the determination of 0.1, 5.0, and 500.0 μg/L of antidepressant drugs. This method was successfully applied to the determination of amitriptyline and chlorpromazine in plasma and urine samples. The recoveries of spiked plasma and urine samples were in the range of 86.1–115.4%. Results indicate that magnetite micro‐solid‐phase extraction with gas chromatography and mass spectrometry is a convenient, fast, and economical method for the extraction and determination of amitriptyline and chlorpromazine in biological samples.