Integrated multienzyme electrochemical biosensors for the determination of glycerol in wines

The construction and performance of integrated amperometric biosensors for the determination of glycerol are reported. Two different biosensor configurations have been evaluated: one based on the glycerol dehydrogenase/diaphorase (GDH/DP) bienzyme system, and another using glycerol kinase/glycerol-3-phosphate oxidase/peroxidase (GK/GPOx/HRP). Both enzyme systems were immobilized together with the mediator tetrathiafulvalene (TTF) on a 3-mercaptopropionic acid (MPA) self-assembled monolayer (SAM)-modified gold electrode by using a dialysis membrane. The electrochemical oxidation of TTF at +150 mV (vs. Ag/AgCl), and the reduction of TTF⁺ at 0 mV were used for the monitoring of the enzyme reactions for the bienzyme and trienzyme configurations, respectively. Experimental variables concerning both the biosensors composition and the working conditions were optimized for each configuration. A good repeatability of the measurements with no need of cleaning or pretreatment of the biosensors was obtained in both cases. After 51 days of use, the GDH/DP biosensor still exhibited 87% of the original sensitivity, while the GK/GPOx/HRP biosensor yielded a 46% of the original response after 8 days. Calibration graphs for glycerol with linear ranges of 1.0 × 10⁻⁶ to 2.0 × 10⁻⁵ or 1.0 × 10⁻⁶ to 1.0 × 10⁻⁵ M glycerol and sensitivities of 1214 ± 21 or 1460 ± 34 μA M⁻¹ were obtained with GDH/DP and GK/GPOx/HRP biosensors, respectively. The calculated detection limits were 4.0 × 10⁻⁷ and 3.1 × 10⁻⁷ M, respectively. The biosensors exhibited a great sensitivity with no significant interferences in the analysis of wines. The biosensors were applied to the determination of glycerol in 12 different wines and the results advantageously compared with those provided by a commercial enzyme kit.     

Amperometric cholesterol biosensors based on the electropolymerization of pyrrole and the electrocatalytic effect of Prussian-Blue layers helped with self-assembled monolayers

Three cholesterol biosensor configurations based on the formation of a layer of Prussian-Blue (PB) on a Pt electrode for the electrocatalytic detection of the H₂O₂ generated during the enzymatic reaction of cholesterol with cholesterol oxidase (ChOx) were constructed. The enzyme was entrapped within a polypyrrole (PPy) layer electropolymerized onto the PB film. The influence of the formation of self-assembled monolayers (SAMs) on the Pt surface on the adherence and stability of the PB layer and the formation of an outer layer of nafion (Nf) as a means of improving selectivity were both studied. A comparative study was made of the analytical properties of the biosensors corresponding to the three configurations named: Pt/PB/PPy-ChOx, Pt/SAM/PB/PPy-ChOx and Pt/SAM/PB/PPy-ChOx/Nf. The sensitivity (from 600 to 8500 nA mM⁻¹ cm⁻²) and selectivity of the developed biosensors permitted the determination of the cholesterol content in reference and synthetic serum samples. The detection limit for the Pt/SAM/PB/PPy-ChOx/Nf biosensor was 8 μM. Formation of the SAM on the electrode surface and covering with a Nf film considerably improved the stability and lifetime of the biosensor based on the catalytic effect of the PB layer (as the PB layer was retained longer on the electrode), and the Nf layer protects the enzyme from the external flowing solutions. Lifetime is up to 25 days of use. The formation of the SAM also has an effect on the charge transfer and the formation of the PB layer.     

Continuous-flow/stopped-flow system for determination of ascorbic acid using an enzymatic rotating bioreactor

The high sensitivity that can be attained using an enzymatic system and mediated by hydroquinone, has been verified by on-line interfacing of a rotating bioreactor and continuous flow/stopped-flow/continuous-flow processing. Horseradish peroxidase, HRP, [EC 1.11.1.7], immobilized on a rotating disk, in presence of hydrogen peroxide catalyses the oxidation of hydroquinone to p-benzoquinone, whose electrochemical reduction back to hydroquinone is detected on glassy carbon electrode (GCE) surface at −0.15 V. Thus, when l-ascorbic acid is added to the solution, this acid is reduced chemically (p-benzoquinone to hydroquinone) and acts as mediator of HRP, decreasing the peak current obtained proportionally to the increase of its concentration. The recovery of l-ascorbic acid from four samples ranged from 99.09 to 101.10%. This method could be used to determine l-ascorbic acid concentration in the range 12 nM-3.5 μM (r = 0.998). The determination of l-ascorbic acid was possible with a limit of detection of 6 nM in the processing of as many as 25 samples h⁻¹. The method was successfully applied for the analysis of l-ascorbic acid in pharmaceutical formulations.     

Sensitivity enhancement of SPR biosensor with silver mirror reaction on the Ag/Au film

Based on well-known silver mirror reaction the Ag film was formed on Au film modified by self-assembled monolayer (SAM) of 1,6-hexanedithiol (HDT). The sensitivity of the biosensor based on this Ag/Au film is enhanced compared to that based on Au film. When the surface plasmon resonance (SPR) biosensor based on this Ag/Au film was used to determine human IgG, the range of concentrations of human IgG that could be determined is 0.30-40.00 μg mL⁻¹. The lowest concentration (0.30 μg mL⁻¹) that could be detected was about 8 times lower than that obtained by the biosensor without modification by Ag film (2.50 μg mL⁻¹), which demonstrated that the biosensor based on Ag/Au film could make the resonant wavelength move to longer wavelength following with the sensitivity enhancement of the SPR biosensor.     

Development of hydrogen peroxide biosensor based on in situ covalent immobilization of horseradish peroxidase by one-pot polysaccharide-incorporated sol-gel process

A simple and reliable one-pot approach was established for the development of a novel hydrogen peroxide (H₂O₂) biosensor based on in situ covalent immobilization of horseradish peroxidase (HRP) into biocompatible material through polysaccharide-incorporated sol-gel process. Siloxane with epoxide ring and trimethoxy anchor groups was applied as the bifunctional cross-linker and the inorganic resource for organic-inorganic hybridization. The reactivity between amine groups and epoxy groups allowed the covalent incorporation of HRP and the functional biopolymer, chitosan (CS) into the inorganic polysiloxane network. Some experimental variables, such as mass ratio of siloxane to CS, pH of measuring solution and applied potential for detection were optimized. HRP covalently immobilized in the hybrid matrix possessed high electrocatalytic activity to H₂O₂ and provided a fast amperometric response. The linear response of the as-prepared biosensor for the determination of H₂O₂ ranged from 2.0 × 10⁻⁷ to 4.6 × 10⁻⁵ mol l⁻¹ with a detection limit of 8.1 × 10⁻⁸ mol l⁻¹. The apparent Michaelis-Menten constant was determined to be 45.18 μmol l⁻¹. Performance of the biosensor was also evaluated with respect to possible interferences. The fabricated biosensor exhibited high reproducibility and storage stability. The ease of the one-pot covalent immobilization and the biocompatible hybrid matrix serve as a versatile platform for enzyme immobilization and biosensor fabricating.     

Development of an enzymeless biosensor for the determination of phenolic compounds

The construction of amperometric enzymeless biosensors for phenolic compounds determination, using carbon paste electrode modified with copper phtalocyanine (CuPc) and histidine (His), based on the chemistry of the dopamine β-monooxygenase (DβM) enzyme that catalyzes the hydroxylation of the dopamine and its analogs is shown. The modified carbon paste was evaluated on electrodes constructed in two ways: putting the paste into a cavity of a rotating disk electrode and a platinum slide electrode fixed into a glass tube. The sensor in hydrodynamic conditions presented a linear response range between 30 and 250 μmol l⁻¹, with a sensitivity of 4.6±0.1 nA l μmol⁻¹ cm⁻² for catechol, response time of 3 s and lifetime of about 50 days when stored at room temperature. The sensor in static conditions showed a linear response range from 40 to 250 μmol l⁻¹, with a sensitivity of 0.30±0.01 nA l μmol⁻¹ cm⁻² for catechol. The sensors presented the following relative response order for dopamine and some analog species: catechol>dopamine>guaiacol>serotonin>phenol.     

Amperometric biosensor for hydrogen peroxide based on coimmobilized horseradish peroxidase and methylene green in ormosils matrix with multiwalled carbon nanotubes

A novel amperometric biosensor for the analytical determination of hydrogen peroxide was developed. The fabrication of the biosensor was based on the coimmobilization of horseradish peroxidase (HRP), methylene green (MG) and multiwalled carbon nanotubes within ormosils; 3-aminopropyltrimethoxysilane (APTMOS), 2-(3,4-epoxycyclohexyl)ethyltrimethoxysilane (ETMOS) and phenyltrimethoxysilane (PHTMOS). APTMOS determined the hydrophilicity/hydrophobicity of the ormosils and PHTMOS and ETMOS increased the physical and mechanical strength of the ormosil matrix. The ormosil modified electrodes were characterized with SEM, UV-vis spectroscopy and electrochemical methods. Cyclic voltammetry and amperometric measurements demonstrated the MG coimmobilized with HRP in this way, displayed good stability and could efficiently shuttle electrons between immobilized enzyme and electrode, and MWCNTs facilitated the electrocatalytic reduction of H₂O₂ at reduced over potential. The Micheaelis constant of the immobilized HRP was 1.8 mM, indicating a high affinity of the HRP to H₂O₂ without loss of enzymatic activity in ormosil matrix. The prepared biosensor had a fast response of H₂O₂, less than 10 s, and excellent linear range of concentration from 5 × 10⁻⁷ to 2 × 10⁻⁵ M with the detection limit of 0.5 μM (S/N = 3) under the optimum conditions. At the same time, the influence of solution pH, effect of enzyme amount, steady-state applied potential and temperature on the biosensor were investigated. The enzyme electrode retained about 90% of its initial activity after 30 days of storage in a dry state at 4 °C. The preparation of the developed biosensor was convenient and showed high sensitivity with good stability.     

Modification of carbon ceramic electrode prepared with sol-gel technique by a thin film of chlorogenic acid: application to amperometric detection of NADH

The carbon ceramic electrode prepared with sol-gel technique is modified by a thin film of chlorogenic acid (CGA). By immersing the carbon ceramic electrode in aqueous solution of chlorogenic acid at less than 2 s a thin film of chlorogenic acid adsorbed strongly and irreversibly on the surface of electrode. The cyclic voltammetry of the resulting modified CCE prepared at optimum conditions shows a well-defined stable reversible redox couple due to hydroquinone/quinone system in both acidic and basic solutions. The modified electrode showed excellent electrocatalytic activity toward NADH oxidation and it also showed a high analytical performance for amperometric detection of NADH. The catalytic rate constant of the modified carbon ceramic electrode for the oxidation of NADH is determined by cyclic voltammetry measurement. Under the optimised conditions the calibration curve is linear in the concentration range 1-120 μm. The detection limit (S/N = 3) and sensitivity are 0.2 μM and 25 nA μM⁻¹.The results of six successive measurement-regeneration cycles show relative standard deviations of 2.5% for electrolyte solution containing 1 mM NADH, indicating that the electrode renewal gives a good reproducible and antifouling surface. The advantages of this amperometric detector are: high sensitivity, excellent catalytic activity, short response time t < 2 s, remarkable long-term stability, simplicity of preparation at short time and good reproducibility.     

Electrocatalytic H2O2 amperometric detection using gold nanotube electrode ensembles

Arrays of nanoscopic gold tubes were prepared by electroless plating of the metal within the pores of nanoporous polycarbonate track-etched membranes. A procedure for fabricating an ensemble of enzyme-modified nanoelectrodes has been developed based on the efficient immobilization of horseradish peroxidase (HRP) to the gold nanotubes array using self-assembled monolayers (mercaptoethylamine or mercaptopropionic acid) as anchoring layers. Hydrogen peroxide (H₂O₂) was determined electrochemically by using gold nanoelectrode ensembles (NEE) functionalized or not in phosphate buffer solution (PB) with or without a mediator (hydroquinone, H₂Q). Bare NEE displays a remarkable sensitivity (14 μA mM⁻¹ in H₂Q at −0.1 V versus Ag/AgCl) compared to a classical gold macroelectrode (0.41 μA mM⁻¹). The gold nanoparticles that form the tubular structure act as excellent catalytic surfaces towards the oxidation and the reduction of H₂O₂. The HRP modified NEE presents a slightly lower sensitivity (9.5 μA mM⁻¹) than bare NEE. However, this system presents an enhanced limit of detection (up to 4 × 10⁻⁶ M) and a higher selectivity towards the detection of H₂O₂ over a wide range of potentials. The lifetime, fabrication reproducibility and measurement repeatability of the HRP enzyme electrode were evaluated with satisfactory results.     

Hydrogen peroxide and peracetic acid determination in waste water using a reversible reagentless biosensor

During the reversible reaction between peroxidase (HRP) and peroxides, several peroxidase intermediate species, showing different molecular absorption spectra, are formed which can be used for their determination. On this basis, a reversible reagentless optical biosensor based on HRP for hydrogen peroxide and peracetic acid determinations has been developed. The biosensor (which can be used for at least 3 months and/or more than 200 measurements) is prepared by HRP entrapment in a polyacrylamide gel matrix. A mathematical model (in which optical, kinetic and transport aspects are considered) relating the measured absorbance with the analyte concentration is also presented. Both peroxides show similar responses in the sensor film. Under the recommended working conditions, the biosensor shows linear response ranges from 6 × 10⁻⁷ to 1.0 × 10⁻⁴ M using FIA mode, and from 2 × 10⁻⁷ to 1.5 × 10⁻⁵ M using continuous mode for both peroxides; the precision, expressed as R.S.D., is about 4%. This biosensor has been applied for peroxide determination in waste water samples previously treated with peroxides.     

Comparative study of different alcohol sensors based on Screen-Printed Carbon Electrodes

Different very simple single-use alcohol enzyme sensors were developed using alcohol oxidase (AOX) from three different yeast, Hansenula sp., Pichia pastoris and Candida boidinii, and employing three different commercial mediator-based Screen-Printed Carbon Electrodes as transducers. The mediators tested, Prussian Blue, Ferrocyanide and Co-phthalocyanine were included into the ink of the working electrode. The procedure to obtain these sensors consists of the immobilization of the enzyme on the electrode surface by adsorption. For the immobilization, an AOX solution is deposited on the working electrode and left until dried (1 h) at room temperature. The best results were obtained with the biosensor using Screen-Printed Co-phthalocyanine/Carbon Electrode and AOX from Hansenula sp. The reduced cobalt–phthalocyanine form is amperometrically detected at +0.4 V (vs. Ag pseudo reference electrode). This sensor shows good sensitivity (1211 nA mM⁻¹), high precision (2.1% RSD value for the slope value of the calibration plot) and wide linear response (0.05–1.00 mM) for ethanol determination. The sensor provides also accurate results for ethanol quantification in alcoholic drinks.     

Electrodeposition of gold nanoparticles on indium/tin oxide electrode for fabrication of a disposable hydrogen peroxide biosensor

A novel disposable third-generation hydrogen peroxide (H₂O₂) biosensor based on horseradish peroxidase (HRP) immobilized on the gold nanoparticles (AuNPs) electrodeposited indium tin oxide (ITO) electrode is investigated. The AuNPs deposited on ITO electrode were characterized by UV-vis, SEM, and electrochemical methods. The AuNPs attached on the ITO electrode surface with quasi-spherical shape and the average size of diameters was about 25 nm with a quite symmetric distribution. The direct electron chemistry of HRP was realized, and the biosensor exhibited excellent performances for the reduction of H₂O₂. The amperometric response to H₂O₂ shows a linear relation in the range from 8.0 μmol L⁻¹ to 3.0 mmol L⁻¹ and a detection limit of 2 μmol L⁻¹ (S/N = 3). The value of HRP immobilized on the electrode surface was found to be 0.4 mmol L⁻¹. The biosensor indicates excellent reproducibility, high selectivity and long-term stability.     

Integrated multienzyme electrochemical biosensors for monitoring malolactic fermentation in wines

Integrated amperometric biosensors for the determination of l-malic and l-lactic acids were developed by coimmobilization of the enzymes l-malate dehydrogenase (MDH) and diaphorase (DP), or l-lactate oxidase (LOX) and horseradish peroxidase (HRP), respectively, together with the redox mediator tetrathiafulvalene (TTF), on a 3-mercaptopropionic acid (MPA) self-assembled monolayer (SAM)-modified gold electrode by using a dialysis membrane. The electrochemical oxidation of TTF at +100 mV (vs. Ag/AgCl), and the reduction of TTF⁺ at −50 mV were used for the monitoring of the enzyme reactions involved in l-malic and l-lactic acid determinations, respectively. Experimental variables concerning the biosensors composition and the detection conditions were optimized for each biosensor. Good relative standard deviation values were obtained in both cases for the measurements carried out with the same biosensor, with no need of cleaning or pretreatment of the bioelectrodes surface, and with different biosensors constructed in the same manner. After 7 days of continuous use, the MDH/DP biosensor still exhibited 90% of the original sensitivity, while the LOX/HRP biosensor yielded a 91% of the original response after 5 days. Calibration graphs for l-malic and l-lactic were obtained with linear ranges of 5.2 × 10⁻⁷ to 2.0 × 10⁻⁵ and 4.2 × 10⁻⁷ to 2.0 × 10⁻⁵ M, respectively. The calculated detection limits were 5.2 × 10⁻⁷ and 4.2 × 10⁻⁷ M, respectively. The biosensors exhibited a high selectivity with no significant interferences. They were applied to monitor malolactic fermentation (MLF) induced by inoculation of Lactobacillus plantarum CECT 748^T into a synthetic wine. Samples collected during MLF were assayed for l-malic and l-lactic acids, and the results obtained with the biosensors exhibited a very good correlation when plotted against those obtained by using commercial enzymatic kits.     

Immobilization of [Cu(bpy)2]Br2 complex onto a glassy carbon electrode modified with α-SiMo12O40 and single walled carbon nanotubes: Application to nanomolar detection of hydrogen peroxide and bromate

A simple procedure has been used for preparation of modified glassy carbon electrode with carbon nanotubes and copper complex. Copper complex [Cu(bpy)₂]Br₂ was immobilized onto glassy carbon (GC) electrode modified with silicomolybdate, α-SiMo₁₂O₄₀⁴⁻ and single walled carbon nanotubes (SWCNTs)_. Copper complex and silicomolybdate irreversibly and strongly adsorbed onto GC electrode modified with CNTs. Electrostatic interactions between polyoxometalates (POMs) anions and Cu-complex, cations mentioned as an effective method for fabrication of three-dimensional structures. The modified electrode shows three reversible redox couples for polyoxometalate and one redox couple for Cu-complex at wide range of pH values. The electrochemical behavior, stability and electron transfer kinetics of the adsorbed redox couples were investigated using cyclic voltammetry. Due to electrostatic interaction, copper complex immobilized onto GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ electrode shows more stable voltammetric response compared to GC/CNTs/Cu-complex modified electrode. In comparison to GC/CNTs/Cu-complex the GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ modified electrodes shows excellent electrocatalytic activity toward reduction H₂O₂ and BrO₃⁻ at more reduced overpotential. The catalytic rate constants for catalytic reduction hydrogen peroxide and bromate were 4.5(±0.2) × 10³ M⁻¹ s⁻¹ and 3.0(±0.10) × 10³ M⁻¹ s⁻¹, respectively. The hydrodynamic amperommetry technique at 0.08 V was used for detection of nanomolar concentration of hydrogen peroxide and bromate. Detection limit, sensitivity and linear concentration range proposed sensor for bromate and hydrogen peroxide detection were 1.1 nM and 6.7 nA nM⁻¹, 10 nM-20 μM, 1 nM, 5.5 nA nM⁻¹ and 10 nM-18 μM, respectively.     

Electrochemistry and scanning electron microscopy of polyaniline/peroxidase-based biosensor

An amperometric biosensor was prepared by in situ deposition of horseradish peroxidase (HRP) enzyme on a polyaniline (PANI)-doped platinum disk electrode. The PANI film was electrochemically deposited on the electrode at 100 mV s⁻¹/Ag-AgCl. Cyclic voltammetric characterization of the PANI film in 1 M HCl showed two distinct redox peaks, which prove that the PANI film was electroactive and exhibited fast reversible electrochemistry. The surface concentration and film thickness of the adsorbed electroactive species was estimated to be 1.85×10⁻⁷ mol cm⁻² and approximately 16 nm, respectively. HRP was electrostatically immobilized onto the surface of the PANI film, and voltammetry was used to monitor the electrocatalytic reduction of hydrogen peroxide under diffusion-controlled conditions. Linear responses over the concentration range 2.5×10⁻⁴ to 5×10⁻³ M were observed. Spectroelectrochemistry was used to monitor the changes in UV-vis properties of HRP, before and after the catalysis of H₂O₂. The biosensor surface morphology was characterized by scanning electron microscopy (SEM) using PANI-doped screen-printed carbon electrodes (SPCEs) in the presence and absence of (i) peroxidase and (ii) peroxide. The SEM images showed clear modifications of the conducting film surface structure when doped with HRP, as well as the effect of hydrogen peroxide on the morphology of biosensor.     

Whole-cell Gluconobacter oxydans biosensor for 2-phenylethanol biooxidation monitoring

A microbial biosensor for 2-phenylethanol (2-PE) based on the bacteria Gluconobacter oxydans was developed and applied in monitoring of a biotechnological process. The cells of G. oxydans were immobilized within a disposable polyelectrolyte complex gel membrane consisting of sodium alginate, cellulose sulphate and poly(methylene-co-guanidine) attached onto a miniaturized Clark oxygen electrode, forming whole cell amperometric biosensor. Measured changes in oxygen concentration were proportional to changes in 2-PE concentration. The biosensor sensitivity was 864 nA mM⁻¹ (RSD = 6%), a detection limit of 1 μM, and the biosensor response towards 2-PE was linear in the range 0.02–0.70 mM. The biosensor preserved 93% of its initial sensitivity after 7 h of continuous operation and exhibited excellent storage stability with loss of only 6% of initial sensitivity within two months, when stored at 4 °C. The developed system was designed and successfully used for an off-line monitoring of whole course of 2-PE biooxidation process producing phenylacetic acid (PA) as industrially valuable aromatic compound. The biosensor measurement did not require the use of hazardous organic solvent. The biosensor response to 2-PE was not affected by interferences from PA and phenylacetaldehyde at concentrations present in real samples during the biotransformation and the results were in a very good agreement with those obtained via gas chromatography.     

ZnS quantum dots derived a reagentless uric acid biosensor

A reagentless amperometric uric acid biosensor based on zinc sulfide (ZnS) quantum dots (QDs) was firstly developed. It could detect uric acid without the presence of an electron mediator. The carboxyl group functionalized ZnS QDs were synthesized, and they were soluble biocompatible and conductive. ZnS QDs conjugates could provide increased enzyme binding sites, which may result in higher enzyme loading. Thus, the proposed uricase/ZnS QDs/l-cys biosensor exhibited higher amperometric response compared to the one without QDs (uricase/l-cys biosensor). In addition, there was little AA interference. It showed a linear dependence on the uric acid concentration ranging from 5.0 × 10⁻⁶ to 2.0 × 10⁻³ mol L⁻¹ with a detection limit of 2.0 × 10⁻⁶ mol L⁻¹ at 3σ.     

Bilayer lipid membrane biosensor with enhanced stability for amperometric determination of hydrogen peroxide

In this paper, a polydopamine (PDA) film is electropolymerized on the surface of bilayer lipid membrane (BLM) which is immobilized with horseradish peroxidase (HRP). The coverage of the PDA film on HRP/BLM electrode is monitored by electrochemical impedance spectroscopy (EIS). The electrocatalytic reduction of H₂O₂ at the PDA/HRP/BLM electrode is studied by means of cyclic voltammetry (CV). The biosensor has a fast response to H₂O₂ of less than 5 s and an excellent linear relationship is obtained in the concentration range from 2.5 × 10⁻⁷ to 3.1 × 10⁻³ mol L⁻¹, with a detection limit of 1.0 × 10⁻⁷ mol L⁻¹ (S/N = 3). The response current of BLM/HRP/PDA biosensor retains 84% of its original response after being stored in 0.1 mol L⁻¹ pH 7.0 PBS at 4 °C for 3 weeks. The selectivity, repeatability, and storage stability of PDA/HRP/BLM biosensor are greatly enhanced by the coverage of polydopamine film on BLM.     

A sensitive mediator-free tyrosinase biosensor based on an inorganic-organic hybrid titania sol-gel matrix

A novel inorganic-organic hybrid titania sol-gel nanocomposite film was prepared to fabricate a sensitive tyrosinase biosensor for the amperometric detection of trace phenolic compounds without additional electron mediators. Acetylacetone worked as a complexing ligand to chelate with Ti atom in the synthesis process, and the pH of the titania solution could be adjusted to the value which was optimum for retaining tyrosinase activity and such a membrane was stably attached on to the surface of a glassy carbon electrode (GCE). This titania matrix could supply a good environment for enzyme loading, which resulted in a high sensitivity of 15.78 μA μM⁻¹ cm⁻² for monitoring phenols with a detection limit of 1×10⁻⁸ M at a signal-to-noise ratio of 3. The TiO₂ sol-gel derived biosensor exhibited a fast response less than 10 s and a good stability for more than 2 months.     

Mesoporous silica hollow sphere (MSHS) for the bioelectrochemistry of horseradish peroxidase

In this work, novel mesoporous silica hollow spheres (MSHS) were chosen as an immobilization matrix, to construct a mediator-free third-generation HRP biosensor. UV-vis spectroscopy revealed that horseradish peroxidase (HRP) entrapped in MSHS could retain its native structure. FTIR spectroscopy and nitrogen adsorption-desorption isotherms indicated that HRP are intercalated into the mesopores. The direct electron transfer of HRP entrapped in MSHS was observed. A pair of stable and well-defined redox peaks of HRP with a formal potential of about −0.150 V (vs. Ag/AgCl) in 0.1 M pH 7.0 phosphate-buffered solution (PBS) were obtained. The biosensor exhibited a fast amperometric response to H₂O₂ with a linear range of 3.9 × 10⁻⁶ to 1.4 × 10⁻⁴ M (R = 0.997, N = 20). The detection limit was 1.2 × 10⁻⁶ M based S/N = 3.